PIC16LF627-04/SO - 4MHz 8-Bit Flash MCU, 1.75KB | Microchip
Артикул: PIC16LF627-04/SO ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.85 | $2,85 |
| 10 | $2.55 | $25,50 |
| 100 | $2.1 | $210,00 |
| 500 | $1.78 | $890,00 |
| 1.000 | $1.45 | $1.450,00 |
PIC16LF627-04/SO Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (flash/RAM/EEPROM), and peripherals such as timers, ADC, communication interfaces, and I/O. Within the broader classification hierarchy, the PIC16LF627-04/SO belongs to: microcontroller -> embedded controller -> 8-bit MCU -> RISC MCU -> flash-based MCU -> semiconductor IC. The 8-bit PIC mid-range family targets cost-sensitive, deterministic embedded applications where simplicity, low power, and wide toolchain support outweigh the throughput advantage of 16/32-bit cores.
Key features include an internal 4MHz RC oscillator (no external crystal required for many designs), a 10-bit ADC with 8 channels, two 8-bit timers (Timer0, Timer2) plus one 16-bit timer (Timer1), a USART for serial communication, and a capture/compare/PWM (CCP) module. The device also integrates a comparator, brown-out reset, watchdog timer with on-chip dedicated oscillator, and an in-circuit serial programming (ICSP) interface for field upgrades without removing the chip.
The Harvard architecture separates program and data buses, allowing instruction fetch and operand access in the same cycle, which combined with the 14-bit wide instruction word gives high code density. Power management features include nanoWatt technology with multiple idle/sleep modes (typical 100nA standby), and a wide 2.0V-5.5V operating range that allows direct battery connection for 2x AA cells and simplifies designs migrating between 3.3V and 5V rails.
Typical applications include consumer remote controls, small appliance control, sensor signal conditioning, low-end security keypads, lighting controllers, and battery-powered handheld instrumentation. The combination of integrated peripherals, low power, and small SOIC-18 footprint makes it attractive for space- and cost-constrained embedded designs.
When designing with this device, verify whether the comparator and ADC reference are needed for your application - both share pins with digital I/O and require careful pin assignment. Use the ICSP interface to keep prototypes reprogrammable without removing the chip from the board.
This page synthesizes distributor pricing, drop-in compatible alternatives from the same Microchip PIC16F62X family, and practical design notes for engineers working on 8-bit embedded designs where PIC ecosystem familiarity, low BOM cost, or long-term Microchip availability are decision drivers.
Аналоги без доработки для PIC16LF627-04/SO — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16LF627-04/SO (тот же форм-фактор и посадочное место) — отличается по Package, Internal Oscillator, Operating Temperature, Timers, I/O Pins.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16LF627-04I/SO
✅ Прямая замена✓ В наличии
$2.55 / шт.
Открыть даташит →PIC16F627-04/SO
✅ Прямая замена✓ В наличии
$1.85 / шт.
Открыть даташит →PIC16F627-04I/SO
✅ Прямая замена✓ В наличии
$1.59 / шт.
Открыть даташит →PIC16LF628-04/SO
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16F628-04I/SO
✅ Прямая замена✓ В наличии
$2.3 / шт.
Открыть даташит →PIC16LF627A-I/SO
✅ Прямая замена✓ В наличии
$1.65 / шт.
Открыть даташит →PIC16LF627-04/SO Максимальные параметры и электрические характеристики
| Core Architecture | PIC RISC, 8-bit, Harvard |
| Instruction Set | 35 instructions, 14-bit word |
| Max CPU Frequency | 4 MHz |
| Program Memory (Flash) | 1.75 KB (1K x 14) |
| Data RAM | 224 bytes |
| Data EEPROM | 128 bytes |
| I/O Pins | 16 |
| Operating Voltage | 2.0 V to 5.5 V |
| ADC | 10-bit, 8 channels |
| Timers | 2x 8-bit (TMR0/TMR2), 1x 16-bit (TMR1) |
| Communication | USART (SCI) |
| CCP Module | 1 (Capture/Compare/PWM) |
| Analog Comparator | Yes (1 pair) |
| Brown-Out Reset | Yes |
| Watchdog Timer | Yes, with dedicated oscillator |
| ICSP Programming | Yes |
| Internal Oscillator | Yes, 4 MHz |
| Power-Saving Modes | nanoWatt Technology (multiple sleep/idle) |
| Рабочая температура | 0C to +70C (Commercial) |
| Корпус | 18-SOIC (SOIC-18) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов PIC16LF627-04/SO
| Контакт 1 | RA2/AN2/CVREF — GPIO RA2 / ADC channel 2 / comparator voltage reference output |
| Контакт 2 | RA3/AN3/CMP1 — GPIO RA3 / ADC channel 3 / comparator 1 output |
| Контакт 3 | RA4/T0CKI/CMP2 — GPIO RA4 / Timer0 clock input / comparator 2 output |
| Контакт 4 | RA5/MCLR/VPP — GPIO RA5 / Master Clear (reset, active low) / ICSP programming voltage |
| Контакт 5 | VSS — Ground reference |
| Контакт 6 | RB0/INT — GPIO RB0 / external interrupt input |
| Контакт 7 | RB1/RX/DT — GPIO RB1 / USART RX / synchronous data line |
| Контакт 8 | RB2/TX/CK — GPIO RB2 / USART TX / synchronous clock line |
| Контакт 9 | RB3/CCP1 — GPIO RB3 / Capture Compare PWM module 1 |
| Контакт 10 | RB4/PGM — GPIO RB4 / LVP programming entry |
| Контакт 11 | RB5 — GPIO RB5 |
| Контакт 12 | RB6/PGC — GPIO RB6 / ICSP programming clock (serial clock) |
| Контакт 13 | RB7/PGD — GPIO RB7 / ICSP programming data (serial data) |
| Контакт 14 | VDD — Positive supply voltage (2.0V to 5.5V) |
| Контакт 15 | OSC1/CLKIN — Oscillator input / external clock input |
| Контакт 16 | OSC2/CLKOUT — Oscillator output / 1/4 system clock output |
| Контакт 17 | RA0/AN0 — GPIO RA0 / ADC channel 0 |
| Контакт 18 | RA1/AN1 — GPIO RA1 / ADC channel 1 |
Типичное применение
PIC16LF627-04/SO подходит для 6 применениеs: Consumer Remote Controls, Small Appliance Control, Sensor Signal Conditioning Hubs, Battery-Powered Handheld Instrumentation, Lighting Controllers, Security Keypads and Access Panels.
Consumer Remote Controls
The PIC16LF627-04/SO is well suited for consumer remote controls where its 16 I/O pins can directly scan a 4x4 key matrix without external drivers, and the internal 4MHz oscillator eliminates the need for an external crystal, reducing BOM cost. The 1.75KB flash comfortably holds protocol stacks for NEC, RC5, or Sony SIRC IR encoders, and the nanoWatt sleep modes drop quiescent current to roughly 100nA between button presses, extending alkaline battery life to over a year. The 10-bit ADC handles battery voltage monitoring while the USART supports learning-mode bridges to other household devices.
Рекомендуется
Small Appliance Control
For small appliance controllers (coffee makers, fans, toasters, blender controls), the PIC16LF627-04/SO provides the right mix of analog and digital integration: 8 channels of 10-bit ADC read temperature sensors, motor current, and user potentiometers; the CCP module drives TRIAC or PWM outputs for heater and motor power control; and the integrated comparator handles zero-crossing detection for line-powered applications. The wide 2.0V-5.5V supply range supports both battery backup and rectified-mains-derived rails. Brown-out reset and watchdog timer protect against supply glitches common in motor-driven loads.
Рекомендуется
Sensor Signal Conditioning Hubs
The PIC16LF627-04/SO works as a low-cost sensor hub that reads analog sensors via its 10-bit ADC, applies digital filtering in firmware, and outputs conditioned data over the USART or via PWM. Industrial measurement integrators (PLCs, HVAC, building automation) often use this PIC to convert 4-20mA loop or thermistor/bridge signals into clean digital outputs. The 224-byte RAM accommodates moving-average buffers while the internal 4MHz oscillator ensures consistent sampling rates without crystal compensation across temperature.
Рекомендуется
Battery-Powered Handheld Instrumentation
Battery-powered handheld tools (multimeters, light meters, IR thermometers, gas detectors) benefit from the PIC16LF627-04/SO's nanoWatt sleep modes that drop quiescent current to microamp levels, enabling years of standby life on a single coin cell. The 1.75KB flash holds calibration tables and measurement routines, while the integrated ADC and comparator simplify front-end designs. The 18-SOIC package occupies minimal PCB area, allowing slim handheld form factors with 16 I/O pins to drive LCD segments, LEDs, and user buttons.
Рекомендуется
Lighting Controllers
LED lighting controllers, dimmers, and color-mixing fixtures use the PIC16LF627-04/SO to generate multiple PWM channels for RGB or warm-white LED strings, manage dimming curves in firmware, and respond to user inputs via the 10-bit ADC. The CCP module provides one hardware PWM channel, and additional channels are generated via timer interrupts in the 1.75KB flash. The internal 4MHz oscillator is precise enough for flicker-free dimming above 100Hz PWM frequency, while the 2.0V-5.5V range supports both 3.3V logic-level LEDs and 5V analog dimmer interfaces.
Рекомендуется
Security Keypads and Access Panels
Low-end security keypads, garage-door entry pads, and access-control panels rely on the PIC16LF627-04/SO to scan 3x4 or 4x4 key matrices using 16 I/O pins, debounce inputs in firmware, and drive relays or buzzer outputs. The internal EEPROM stores user PINs and access codes with 100k write-cycle endurance, and the brown-out reset prevents EEPROM corruption during power glitches. The 1.75KB flash holds complete entry logic, lockout-after-N-attempts state machines, and serial output to a master controller via the integrated USART.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16LF627-04/SO — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16LF627-04I/SO | PIC16F627-04/SO | PIC16F627-04I/SO | PIC16LF628-04/SO | PIC16F628-04I/SO | PIC16LF627A-I/SO |
|---|---|---|---|---|---|---|---|
| Package | SOIC-18 | SOIC-18 - same | SOIC-18 - same | SOIC-18 - same | SOIC-18 - same | SOIC-18 - same | SOIC-18 - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 1.75 KB (1K x 14) | 1.75 KB | 1.75 KB | 1.75 KB | 3.5 KB (2K x 14) | 3.5 KB | 1.75 KB |
| Data RAM | 224 bytes | 224 bytes | 224 bytes | 224 bytes | 224 bytes | 224 bytes | 224 bytes |
| Data EEPROM | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 256 bytes | 256 bytes | 128 bytes |
| Max CPU Frequency | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz |
| Operating Voltage | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| Operating Temperature | 0C to +70C (Commercial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| nanoWatt Sleep Modes | Yes (LF variant) | Yes | No (standard variant) | No | Yes | No | Yes (improved) |
Ключевые отличия
- Wide 2.0V-5.5V supply range with nanoWatt sleep modes (против PIC16F627-04/SO)
- Industrial temperature variant available in same 18-SOIC package (против PIC16LF627-04I/SO)
- Pin-compatible upgrade path to 3.5KB flash (против PIC16LF628-04/SO)
Заметки по проектированию
The PIC16LF627-04/SO supports nanoWatt technology with multiple idle/sleep modes drawing as little as 100nA typical standby current per Microchip datasheet 40300D. To maximize battery life, configure unused peripherals to off via PCON/PIE registers before entering sleep, and use INT-on-change (RB0-RB7) to wake the MCU rather than polling loops. Brown-out reset must be enabled in the configuration words to prevent EEPROM corruption during battery voltage decay.
Two critical configuration traps are documented in the Microchip datasheet: (1) MCLR (pin 4) must be tied to VDD through a 10k resistor or left as input-only if not used as reset - leaving it floating causes spurious resets; (2) The ICSP pins PGC (RB6) and PGD (RB7) must not be pulled low at power-up if LVP is enabled in config words, or the device enters programming mode and the application fails to start. Use a 10k pull-up on RB7 if external circuitry might drive it low at boot.
For the 18-SOIC package, place a 100nF decoupling capacitor within 5mm of the VDD pin (pin 14) and a 10uF bulk capacitor on the same supply rail for transient response. The internal 4MHz oscillator does not require external capacitors, but if you switch to an external crystal via the configuration words, keep the crystal traces short (under 10mm) and surround them with a ground guard ring to reduce EMI susceptibility per Microchip analog PIC mid-range design guidelines.
Информация о соответствии
RoHS compliant per Microchip product page. Lead-free SOIC-18 package. Not AEC-Q100 qualified (commercial grade); choose PIC16LF627-04I/SO for industrial-grade or automotive-cabin applications. Conflict-minerals compliant per Microchip supply chain disclosures.