PIC16LF77-I/L - 8-bit 20MHz PIC MCU 14KB Flash 44-PLCC | Microchip
Артикул: PIC16LF77-I/L ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.2 | $8,20 |
| 10 | $7.45 | $74,50 |
| 100 | $6.55 | $655,00 |
| 500 | $5.95 | $2.975,00 |
| 1.000 | $5.4 | $5.400,00 |
PIC16LF77-I/L Обзор
An 8-bit PIC microcontroller is a Harvard-architecture RISC processor family from Microchip that executes one instruction per clock cycle (except branches), with separate program and data buses that allow simultaneous instruction fetch and data access. Within the broader taxonomy, this device sits in the hierarchy PIC16 -> mid-range PIC -> 8-bit PIC microcontroller -> microcontroller -> embedded processor -> semiconductor. The 'LF' suffix denotes the low-voltage Flash variant that supports operation down to 2.0 V, distinguishing it from the standard PIC16F77 which has a 4.5 V to 5.5 V operating range. The 'I' temperature grade designates the -40 C to +85 C industrial range.
Key differentiating features include the 14 KB Flash program memory (in-system programmable via ICSP), 368-byte data RAM, 256-byte EEPROM data memory, brown-out reset, power-on reset, watchdog timer with its own on-chip RC oscillator, and an 8-bit ADC with 8 input channels. The integrated USART, SSP (SPI/I2C), and two CCP modules significantly reduce external component count. The 33 I/O pins can source/sink up to 25 mA per pin, enabling direct LED drive and interface to power devices without buffering.
The PIC16LF77 uses Microchip's standard mid-range instruction set with 35 single-word/cycle instructions and a 14-bit instruction word. Its deterministic interrupt latency (3 or 4 cycles) and hardware stack (8 levels deep) make it well suited to real-time control loops. The Harvard bus, separate instruction and data paths, and the wide voltage tolerance let the device operate reliably in noisy industrial environments.
Typical applications include industrial control panels, motor control sub-systems, HVAC sensor nodes, automotive body electronics subsystems, smart metering, and embedded operator interfaces with LCDs. The wide voltage tolerance and 33 I/O lines are particularly attractive for legacy industrial designs where the PIC16F877/F777 footprint is already established.
Designers should note that the PLCC-44 socket footprint allows easy prototyping and field replacement, but new designs should consider migrating to PIC16F1xxx or PIC18 families for lower power and more peripherals. A 100 nF decoupling capacitor must be placed within 25 mm of the VDD pins, and an external 4 MHz to 20 MHz crystal or resonator is required for the primary oscillator.
This page synthesizes verified distributor pricing, drop-in PLCC-44 alternatives drawn from Microchip's PIC16 mid-range family, and PCB layout notes not found in the manufacturer datasheet alone.
Аналоги без доработки для PIC16LF77-I/L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16LF77-I/L (тот же форм-фактор и посадочное место) — отличается по Package, ADC, Operating Temperature, Timers, CCP Modules.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16F77-I/L
✅ Прямая замена✓ В наличии
$7.55 / шт.
Открыть даташит →PIC16LF74-I/L
✅ Прямая замена✓ В наличии
$4.32 / шт.
Открыть даташит →PIC16LF77-I/L Максимальные параметры и электрические характеристики
| Core | PIC16 (8-bit Harvard RISC) |
| Program Memory | 14 KB Flash (8K x 14 words) |
| Data RAM | 368 bytes |
| Data EEPROM | 256 bytes |
| Максимальная тактовая частота | 20 MHz |
| Operating Voltage | 2.0 V to 5.5 V |
| Number of I/O Pins | 33 |
| ADC | 8-bit, 8 channels |
| Timers | Timer0, Timer1 (16-bit), Timer2 |
| CCP Modules | 2 (Capture / Compare / PWM) |
| Serial Interfaces | USART / SPI / I2C (SSP) |
| Корпус | 44-pin PLCC (16.59 x 16.59 mm) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40 C to +85 C (industrial) |
| Instruction Word Length | 14 bits |
| Instruction Count | 35 single-cycle instructions |
| Hardware Stack | 8 levels |
| I/O Pin Drive | 25 mA source / sink per pin |
| Brown-out Reset | Yes (BOR) |
| Watchdog Timer | Yes (with dedicated RC oscillator) |
| In-System Programming | ICSP (2-wire) |
| Статус RoHS | Compliant |
Конфигурация выводов PIC16LF77-I/L
| Контакт 1 | MCLR/VPP — Master clear (reset) input / programming voltage |
| Контакт 2 | RA0/AN0 — Digital I/O / ADC analog input 0 |
| Контакт 3 | RA1/AN1 — Digital I/O / ADC analog input 1 |
| Контакт 4 | RA2/AN2/VREF- — Digital I/O / ADC input 2 / ADC negative reference |
| Контакт 5 | RA3/AN3/VREF+ — Digital I/O / ADC input 3 / ADC positive reference |
| Контакт 6 | RA4/T0CKI — Digital I/O / Timer0 clock input |
| Контакт 7 | RA5/AN4/SS — Digital I/O / ADC input 4 / SPI slave select |
| Контакт 8 | OSC1/CLKI — Oscillator crystal input / external clock input |
| Контакт 9 | OSC2/CLKO — Oscillator crystal output / clock output |
| Контакт 10 | RC0/T1OSO/T1CKI — Digital I/O / Timer1 oscillator output / Timer1 clock |
| Контакт 11 | RC1/T1OSI/CCP2 — Digital I/O / Timer1 oscillator input / CCP2 PWM output |
| Контакт 12 | RC2/CCP1 — Digital I/O / CCP1 PWM output |
| Контакт 13 | RC3/SCK/SCL — Digital I/O / SPI clock / I2C clock |
| Контакт 14 | RC4/SDI/SDA — Digital I/O / SPI data in / I2C data |
| Контакт 15 | RC5/SDO — Digital I/O / SPI data out |
| Контакт 16 | RC6/TX/CK — Digital I/O / USART TX / USART clock |
| Контакт 17 | RC7/RX/DT — Digital I/O / USART RX / USART data |
| Контакт 18 | GND — Ground reference |
| Контакт 19 | GND — Ground reference |
| Контакт 20 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| Контакт 21 | RB0/INT — Digital I/O / external interrupt |
| Контакт 22 | RB1 — Digital I/O |
| Контакт 23 | RB2 — Digital I/O |
| Контакт 24 | RB3/PGM — Digital I/O / ICSP programming clock |
| Контакт 25 | RB4 — Digital I/O |
| Контакт 26 | RB5/PGM — Digital I/O / ICSP data |
| Контакт 27 | RB6/PGC — Digital I/O / ICSP clock |
| Контакт 28 | RB7/PGD — Digital I/O / ICSP data |
| Контакт 29 | VSS — Ground (logic ground) |
| Контакт 30 | RD0/PSP0 — Digital I/O / Parallel Slave Port bit 0 |
| Контакт 31 | RD1/PSP1 — Digital I/O / Parallel Slave Port bit 1 |
| Контакт 32 | RD2/PSP2 — Digital I/O / Parallel Slave Port bit 2 |
| Контакт 33 | RD3/PSP3 — Digital I/O / Parallel Slave Port bit 3 |
| Контакт 34 | RD4/PSP4 — Digital I/O / Parallel Slave Port bit 4 |
| Контакт 35 | RD5/PSP5 — Digital I/O / Parallel Slave Port bit 5 |
| Контакт 36 | RD6/PSP6 — Digital I/O / Parallel Slave Port bit 6 |
| Контакт 37 | RD7/PSP7 — Digital I/O / Parallel Slave Port bit 7 |
| Контакт 38 | VSS — Ground |
| Контакт 39 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| Контакт 40 | RE0/RD — Digital I/O / parallel port read control |
| Контакт 41 | RE1/WR — Digital I/O / parallel port write control |
| Контакт 42 | RE2/CS — Digital I/O / parallel port chip select |
| Контакт 43 | AVDD — Analog supply voltage (tied to VDD) |
| Контакт 44 | AVSS — Analog ground (tied to VSS) |
Типичное применение
PIC16LF77-I/L подходит для 6 применениеs: Industrial Control Panels, HVAC Sensor Nodes, Automotive Body Electronics Subsystems, Smart Metering Edge Nodes, Embedded Operator Interfaces with LCD, Motor Control Sub-Systems.
Industrial Control Panels
The PIC16LF77-I/L fits industrial control panels because its 33 digital I/O pins (each capable of 25 mA source/sink) directly drive indicator LEDs, relay coils, and opto-isolated inputs without external buffers. The wide 2.0 V to 5.5 V supply tolerance simplifies designs that accept both 24 V industrial rails (post-regulation) and battery backup. The 14 KB Flash and 368-byte RAM are adequate for keypad scan, multiplexed 7-segment displays, and Modbus RTU over the integrated USART. The -40 C to +85 C industrial temperature grade is the primary reason this part persists in factory-automation designs.
Рекомендуется
HVAC Sensor Nodes
For HVAC sensor nodes (temperature, humidity, pressure) the PIC16LF77-I/L brings the 8-channel 8-bit ADC and integrated I2C/SPI to a low-cost PLCC package. The 2.0 V to 5.5 V range allows direct operation from a 3.3 V lithium backup during power-line outages, while brown-out reset and watchdog timer keep the node recovering safely from transients on long sensor cables. The 14 KB Flash is sufficient for sensor linearization, hysteresis filtering, and BACnet MS-TP or Modbus framing without external memory.
Рекомендуется
Automotive Body Electronics Subsystems
Although not AEC-Q100 qualified, the PIC16LF77-I/L appears widely in non-safety automotive body subsystems (interior lighting, mirror controllers, seat position memory) where its -40 C to +85 C industrial range, 33 I/O, and integrated CAN-like software UART over its USART simplify node counts. Two CCP modules generate PWM for LED dimming and small DC motor control. PLCC packaging, while legacy, is valued in automotive service environments for socketed replacement. For safety-critical ADAS nodes, designers should select AEC-Q100-qualified dsPIC33 or PIC18 variants.
Рекомендуется
Smart Metering Edge Nodes
The PIC16LF77-I/L's 2.0 V to 5.5 V operating range and 256-byte on-chip EEPROM make it a fit for smart-metering edge nodes that record pulses from electricity, gas, or water meters. The 8-bit ADC with 8 channels can read battery voltage, temperature, tamper switches, and current-sense amplifiers simultaneously. The integrated I2C master reads RTC and EEPROM companion chips while the USART drives the optical or PLC modem. PLCC sockets reduce field-service time in deployments where battery replacement is operator-handled.
Рекомендуется
Embedded Operator Interfaces with LCD
For embedded operator interfaces that integrate a character LCD (16x2 or 20x4) and a 4x4 keypad, the PIC16LF77-I/L offers 33 I/O - enough to drive the LCD in 4-bit mode plus the keypad matrix plus a beeper and status LEDs without multiplexing. The 14 KB Flash holds custom bitmap font tables and message strings in addition to the menu logic. The 8-bit ADC reads a potentiometer for contrast adjustment. Watchdog timer protects against keypad-scan lockups.
Рекомендуется
Motor Control Sub-Systems
Small DC and stepper motor sub-systems (fans, pumps, valves, conveyor segments) are well served by the PIC16LF77-I/L because its two CCP modules can output independent PWM channels - one for motor speed, one for current limiting or braking. The 8-channel ADC monitors back-EMF, current sense, and supply voltage while the USART exposes a Modbus service interface. Industrial temperature range and 25 mA I/O drive eliminate the need for gate-driver buffers in low-current (<1 A) motor circuits.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16LF77-I/L — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16F77-I/L | PIC16LF74-I/L | PIC16LF777-I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin PLCC (16.59 x 16.59 mm) | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin TQFP - NOT pin-compatible with PLCC |
| Operating Voltage | 2.0 V to 5.5 V | 4.5 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| Program Memory | 14 KB Flash | 14 KB Flash | 7 KB Flash | 14 KB Flash |
| Data RAM | 368 bytes | 368 bytes | 192 bytes | 368 bytes |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Number of I/O Pins | 33 | 33 | 33 | 36 |
| ADC | 8-bit, 8 channels | 8-bit, 8 channels | 8-bit, 8 channels | 10-bit, 14 channels |
| EEPROM | 256 bytes | 256 bytes | 128 bytes | 256 bytes |
Ключевые отличия
- Wider operating voltage than the PIC16F77-I/L (против PIC16F77-I/L)
- More memory than PIC16LF74-I/L in the same PLCC-44 footprint (против PIC16LF74-I/L)
- PLCC-44 package for socketed serviceability (против PIC16LF777-I/PT)
Заметки по проектированию
Place a 100 nF decoupling capacitor within 25 mm of each VDD/AVDD pin (pins 20, 39, and 43) and a 10 uF bulk capacitor on the same supply rail. Connect AVSS (pin 44) directly to the analog ground plane; do not share its trace with switching digital returns. Brown-out reset (BOR) is enabled by config bits; for 3.3 V operation set BOREN=ON with BORV=2.0 V to maximize low-voltage coverage. Estimated: total in-rush current at 20 MHz is approximately 15 mA plus I/O loading.
The PIC16LF77 requires an external 4 MHz to 20 MHz crystal or ceramic resonator on OSC1/OSC2 (pins 8/9) with the correct capacitor load per the crystal datasheet. For low-EMI designs, use a 4-pin SMD crystal with grounded case; for cost-sensitive prototypes a two-pin resonator with internal capacitors is acceptable. If the system clock is supplied externally, drive OSC1 and leave OSC2 unconnected per the Microchip mid-range oscillator note.
The 44-pin PLCC footprint is JEDEC-standard PLCC-44 with 1.27 mm pitch and 16.59 x 16.59 mm body. Keep digital traces more than 5 mm away from the analog ADC inputs (RA0-RA5, RE0-RE2) to minimize crosstalk; route VREF+/VREF- as a Kelvin pair. Place the ICSP test points (RB6/PGC and RB7/PGD) at the board edge so a Microchip PICkit can program the part in-circuit without removing the PLCC socket.
Do not connect any I/O pin directly to voltages above VDD or below VSS - the absolute maximum is VDD + 0.3 V. MCLR (pin 1) requires a 10 kohm pull-up to VDD; failure to do so produces intermittent resets in noisy environments. Watchdog timer must be either enabled in software or explicitly disabled in the config bits - a forgotten WDT can starve the main loop. Estimated: writing to Flash while executing from Flash stalls the CPU for 2-4 ms per row.
Информация о соответствии
RoHS compliant per Microchip product page. 'I' grade is -40 C to +85 C industrial; not AEC-Q100 qualified - choose AEC-Q100 dsPIC33 or PIC18 for automotive safety. Halogen-free status not published by Microchip for this legacy part.
