PIC18F2520-E/SO - 8-bit 25MHz 32KB Flash MCU 28-SOIC | Microchip
Артикул: PIC18F2520-E/SO ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.79 | $6,79 |
| 10 | $6.1 | $61,00 |
| 100 | $5.42 | $542,00 |
| 500 | $4.85 | $2.425,00 |
| 1.000 | $4.36 | $4.360,00 |
PIC18F2520-E/SO Обзор
A PIC18F microcontroller is an enhanced 8-bit Harvard-architecture RISC core in Microchip's PIC18 family. The PIC18F series adds 16-bit wide instructions and a linear program-memory space on top of the legacy PIC16 architecture, while preserving byte-oriented register access. This particular part targets cost-sensitive embedded control applications that need more program space, more I/O, and richer peripherals than the PIC16F family, without moving to a 16-bit MCU. It sits inside the broader microcontroller hierarchy as: 8-bit MCU -> PIC18 family -> PIC18F2xxx sub-family (28-40-44-pin devices) -> PIC18F2520 specifically.
Key differentiating features include 10-bit analog-to-digital conversion (ADC) with up to 10 input channels, nanoWatt Technology power management for reduced active and sleep currents, an enhanced addressable USART, MSSP serial port supporting SPI and I2C (master/slave), capture/compare/PWM (CCP) modules, and 25 I/O pins with individual pull-up control. The on-chip debug (ICD) capability and self-programmability make field firmware updates possible without an external programmer.
Architecturally, the device uses a 16-bit wide instruction set with an 8-bit data path, a 31-level hardware stack, and a priority-level interrupt controller. nanoWatt Technology adds multiple low-power modes (Run, Idle, Sleep and several oscillator-tunable variants), allowing the designer to trade CPU throughput for current consumption in battery-powered nodes.
Typical applications include industrial control and sensor-interface modules, home-automation and building-control nodes, low-cost motor-control signal chains, USB HID bridges (when paired with the PIC18F2550/4550 variant), embedded data acquisition, and consumer appliances requiring reliable 5 V CMOS logic. The PIC18F2520-E/SO is the "E" (Extended) temperature grade variant rated for -40 to +125 C, suitable for industrial environments.
When designing with this part, select decoupling per Microchip's PIC18F2520 datasheet, observe VDD/VSS analog and digital pin separation, and use the MPLAB XC8 compiler with the PIC18 configuration-bit pragma to lock oscillator, watchdog and brown-out behavior at build time.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for engineers evaluating the PIC18F2520-E/SO in production designs.
Аналоги без доработки для PIC18F2520-E/SO — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18F2520-E/SO (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, ADC, Communication Peripherals, Core.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F2520-I/SO
✅ Прямая замена✓ В наличии
$4.65 / шт.
Открыть даташит →PIC18F2520T-E/SO
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F2525-E/SO
✅ Прямая замена✓ В наличии
$3.05 / шт.
Открыть даташит →PIC18F2420-E/SO
✅ Прямая замена✓ В наличии
$3.93 / шт.
Открыть даташит →PIC18F2523-E/SO
✅ Прямая замена✓ В наличии
$5.2 / шт.
Открыть даташит →PIC18F25K20-I/SO
✅ Прямая замена✓ В наличии
$2.55 / шт.
Открыть даташит →PIC18F2520-E/SO Максимальные параметры и электрические характеристики
| Core Architecture | PIC18 (8-bit Harvard RISC) |
| Program Memory (Flash) | 32 KB (16K x 16) |
| RAM | 1.5 KB (3968 bytes) |
| CPU Clock Speed | 25 MHz (max CPU clock) |
| Oscillator Input | 40 MHz (max, 10 MIPS) |
| ADC | 10-bit, up to 10 channels |
| I/O Pins | 25 |
| Communication Peripherals | EUSART, MSSP (SPI / I2C master-slave) |
| CCP/PWM Modules | Capture/Compare/PWM (CCP) |
| Supply Voltage (VDD) | 4.2 V to 5.5 V (typical 5 V) |
| Рабочая температура | -40 C to +125 C (Extended grade) |
| Корпус | 28-pin SOIC (0.295", 7.50 mm width) |
| Тип монтажа | Surface Mount |
| Power Saving | nanoWatt Technology (Run / Idle / Sleep modes) |
| In-Circuit Debug | ICD / ICSP self-programming |
| Статус RoHS | Compliant |
Конфигурация выводов PIC18F2520-E/SO
| Контакт 1 | RA0/AN0 — Digital I/O / Analog input channel 0 |
| Контакт 2 | RA1/AN1 — Digital I/O / Analog input channel 1 |
| Контакт 3 | RA2/AN2/VREF- — Digital I/O / Analog input 2 / ADC VREF- |
| Контакт 4 | RA3/AN3/VREF+ — Digital I/O / Analog input 3 / ADC VREF+ |
| Контакт 5 | RA4/T0CKI/C1OUT — Digital I/O / Timer0 clock input / Comparator 1 output |
| Контакт 6 | RA5/AN4/SS/HLVDIN — Digital I/O / Analog input 4 / SPI slave select / High/Low Voltage Detect input |
| Контакт 7 | VSS — Ground reference |
| Контакт 8 | RA7/OSC1/CLKI — Digital I/O / Oscillator crystal input / External clock input |
| Контакт 9 | RA6/OSC2/CLKO — Digital I/O / Oscillator crystal output / Clock output |
| Контакт 10 | RC0/T1CKI/T3CKI — Digital I/O / Timer1 clock / Timer3 clock |
| Контакт 11 | RC1/CCP2 — Digital I/O / Capture/Compare/PWM 2 |
| Контакт 12 | RC2/CCP1 — Digital I/O / Capture/Compare/PWM 1 |
| Контакт 13 | RC3/SCK/SCL — Digital I/O / MSSP SPI clock / I2C clock |
| Контакт 14 | RC4/SDI/SDA — Digital I/O / MSSP SPI data in / I2C data |
| Контакт 15 | RC5/SDO — Digital I/O / MSSP SPI data out |
| Контакт 16 | RC6/TX/CK — Digital I/O / EUSART async transmit / sync clock |
| Контакт 17 | RC7/RX/DT — Digital I/O / EUSART async receive / sync data |
| Контакт 18 | VSS — Ground reference |
| Контакт 19 | VDD — Positive supply (4.2V to 5.5V) |
| Контакт 20 | RB0/INT0/FLT0 — Digital I/O / External interrupt 0 / PWM fault input |
| Контакт 21 | RB1/INT1 — Digital I/O / External interrupt 1 |
| Контакт 22 | RB2/INT2/CTEDS — Digital I/O / External interrupt 2 / CTMU edge select |
| Контакт 23 | RB3/CTED1/CCP2 — Digital I/O / CTMU edge 1 / CCP2 alt |
| Контакт 24 | RB4/KBI0 — Digital I/O / Interrupt-on-change KBI0 |
| Контакт 25 | RB5/KBI1/PGM — Digital I/O / Interrupt-on-change KBI1 / LVP programming |
| Контакт 26 | RB6/KBI2/PGC — Digital I/O / Interrupt-on-change KBI2 / ICD clock |
| Контакт 27 | RB7/KBI3/PGD — Digital I/O / Interrupt-on-change KBI3 / ICD data |
| Контакт 28 | VDD — Positive supply (4.2V to 5.5V) |
Типичное применение
PIC18F2520-E/SO подходит для 6 применениеs: Industrial Sensor Interface Module, Home Automation / Building Control Node, Low-Cost Motor Control Signal Chain, Consumer Appliance User Interface Board, USB HID / CDC Bridge (PIC18F2550 Family Companion), Embedded Data Acquisition Front-End.
Industrial Sensor Interface Module
The Microchip PIC18F2520-E/SO is well matched to industrial 4-20 mA / 0-10 V sensor-interface modules because it integrates a 10-bit ADC with up to 10 input channels in a 28-SOIC footprint. With 32 KB flash and 1.5 KB RAM, the part runs basic Modbus RTU slave firmware or a simple proprietary polling protocol without needing external memory; the EUSART handles the RS-485 link directly via an external transceiver. The -40 C to +125 C extended grade ensures operation inside sealed IP65 enclosures near motors or heaters. nanoWatt Technology sleep currents drop to <1 uA in Sleep, enabling loop-powered designs that idle between measurements.
Рекомендуется
Home Automation / Building Control Node
For building-automation nodes (lighting, blinds, HVAC dampers), the PIC18F2520-E/SO offers 25 I/O pins and PWM outputs to drive relays or triac optocouplers without external logic. The 25 MHz CPU and 32 KB flash comfortably execute a Modbus or BACnet MS/TP slave stack. nanoWatt Technology idle/sleep modes let the node consume <2 mA average while polling the bus. The 28-SOIC package fits standard 1-inch-square control modules; the Extended -40 C to +125 C grade covers unheated equipment closets.
Рекомендуется
Low-Cost Motor Control Signal Chain
The PIC18F2520-E/SO CCP modules generate complementary PWM to drive small BLDC or brushed DC motor pre-drivers in a 28-SOIC compact board. With 25 MIPS CPU throughput the firmware can run a sensorless BEMF zero-crossing detection loop at 10 kHz PWM rate while servicing the ADC for current sensing. The MSSP SPI port links to a gate-driver such as the MCP8021 or to a digital potentiometer for closed-loop speed control. nanoWatt sleep keeps the standby current below 1 uA when the motor is parked.
Рекомендуется
Consumer Appliance User Interface Board
Inside a white-good user-interface board (washing machine, microwave, dishwasher), the PIC18F2520-E/SO drives 7-segment LED displays, matrix keypads, and rotary encoders from its 25 I/O pins. The MSSP SPI port connects to an SPI OLED or segment driver; the EUSART serves a service-port diagnostic link to the main control board. With 32 KB flash, manufacturers can ship multiple firmware variants (regional, OEM) on the same hardware platform with self-programmable ICSP field updates.
Рекомендуется
USB HID / CDC Bridge (PIC18F2550 Family Companion)
Although the PIC18F2520-E/SO itself lacks an internal USB peripheral, designers frequently use it alongside the PIC18F2550 in two-MCU bridges where the PIC18F2550 handles the USB physical layer and the PIC18F2520-E/SO runs the application logic. With 25 MIPS throughput and 32 KB flash, the PIC18F2520-E/SO can preprocess sensor data or run a HID report-mapping algorithm and exchange data with the USB MCU over EUSART. The 28-SOIC surface-mount package keeps the bridge board inside low-profile enclosures.
Рекомендуется
Embedded Data Acquisition Front-End
The PIC18F2520-E/SO serves as a battery-powered data-acquisition front end: the 10-bit ADC samples up to 10 inputs at up to 100 ksps aggregate, and the MSSP port offloads buffered samples to an SD card or external FRAM via SPI. With nanoWatt Technology Sleep currents in the single-digit microamp range, the front end can idle most of the time and wake on a timer or external interrupt, dramatically extending battery life in remote-instrumentation installations. The -40 C to +125 C extended grade handles outdoor weather stations.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18F2520-E/SO — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F2520-I/SO | PIC18F2520T-E/SO | PIC18F2525-E/SO | PIC18F2420-E/SO | PIC18F2523-E/SO | PIC18F25K20-I/SO |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SOIC | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same |
| Flash Memory | 32 KB | 32 KB | 32 KB | 48 KB (+16 KB) | 16 KB (-16 KB) | 32 KB | 32 KB |
| RAM | 1.5 KB (3968 B) | 1.5 KB | 1.5 KB | 4 KB | 1 KB | 1.5 KB | 1.5 KB |
| CPU Clock (max) | 25 MHz (10 MIPS @ 40 MHz osc) | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 48 MHz (12 MIPS) | 64 MHz / 16 MIPS (K-series) |
| ADC Resolution | 10-bit, 10 channels | 10-bit | 10-bit | 10-bit | 10-bit | 12-bit | 10-bit |
| Operating Temperature | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +85 C |
| Power Saving | nanoWatt Technology | nanoWatt Technology | nanoWatt Technology | nanoWatt Technology | nanoWatt Technology | nanoWatt Technology | nanoWatt XLP |
Ключевые отличия
- Extended -40 C to +125 C temperature grade over the Industrial-grade sibling (против PIC18F2520-I/SO)
- Highest flash/RAM tier in the PIC18F2x20 family (против PIC18F2420-E/SO)
- Full nanoWatt Technology vs XLP on K-series refresh (против PIC18F25K20-I/SO)
Заметки по проектированию
Estimated: at 25 MHz CPU clock on 5 V supply with all peripherals active, the PIC18F2520-E/SO draws roughly 12-15 mA (datasheet IDD vs frequency curve). Add a 100 nF ceramic decoupling capacitor on each of the two VDD pins (pin 19 and pin 28) and a single bulk 10 uF tantalum or aluminum-polymer cap within 25 mm of the package. Place analog and digital VDD/VSS traces so return currents do not share the same copper segment under the SOIC, preventing ADC reference bounce during CCP switching.
Keep the 28-SOIC land pattern per IPC-7351 SOIC127P762X203-28M (0.65 mm pitch, 7.5 mm body). Place the ICSP/ICD pins (RB6/PGC, RB7/PGD, RA5/PGM) on a 0.1" header or test-point pad so the PICkit 5 can attach. For production programming, route the PGC/PGD traces to a 6-pin right-angle connector at the board edge. Avoid long parallel traces under the crystal (RA6/OSC2, RA7/OSC1) - ground-guard both signals for EMI suppression. The Extended-grade part's -40 C to +125 C range can be exercised in chamber testing by trimming the resistor values for brown-out if needed.
Do not confuse the PIC18F2520 / PIC18F25K20 / PIC18F2620 silicon - the K20 SFR names and oscillator control registers differ and firmware does not port. Verify brown-out voltage (BORV) configuration bits match the supply ramp rate; on a slow-ramping supply (USB bus-powered) set BORV=00 (max) to avoid spurious resets. Read-modify-write operations on PORT registers (LATx) require the read-after-write timing; in interrupt service routines use the LATx register, not PORTx, to avoid one-cycle ghost-write artifacts on the I/O pin.
Информация о соответствии
RoHS and REACH compliance per Microchip product page. The PIC18F2520 family is not AEC-Q100 qualified - for automotive designs, refer to the PIC18F-K-series Q-graded variants. Halogen-free status not stated on the public datasheet; defaulted to "unknown" per Data Authenticity Rule.
