PIC18F452T-I/L - 8-Bit 40MHz 32KB Flash MCU 44-PLCC | Microchip
Артикул: PIC18F452T-I/L ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.32 | $6,32 |
| 10 | $5.78 | $57,80 |
| 100 | $5.05 | $505,00 |
| 500 | $4.42 | $2.210,00 |
| 1.000 | $3.88 | $3.880,00 |
PIC18F452T-I/L Обзор
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, on-chip FLASH program memory, RAM, peripherals, and an arithmetic-logic unit. Within the broader semiconductor taxonomy, the PIC18F452 belongs to the hierarchy: microcontroller -> 8-bit MCU -> FLASH MCU -> PIC18 family -> PIC18F452 sub-family. The 8-bit class remains widely used because it offers deterministic interrupt response, low cost, and low power for embedded control where the throughput of 32-bit Cortex-M parts is unnecessary.
Key features that distinguish this device include 77 single-word instructions (simplifying compiler and assembly code), an enhanced FLASH program memory supporting 100K erase/write cycles, an ICD-friendly in-circuit debug interface, hardware multiplier for 8x8 unsigned operations in a single cycle, and self-programming capability that allows field firmware upgrades through the USART. The MSSP peripheral supports both SPI master/slave and I2C master/slave modes, while the USART handles RS-232/RS-485 links commonly found in industrial automation.
Typical applications include industrial control and sensor interfaces, building automation controllers, HVAC thermostats, instrument data loggers, low-end human-machine interface (HMI) panels, and consumer appliance control boards. Its 10-bit ADC, generous I/O count, and rugged industrial temperature grade make it well-suited to factory-floor designs where reliability over decades matters more than peak compute throughput. The PIC18F452 is also widely used as a teaching platform in university embedded systems curricula and as an upgrade target for legacy PIC16C/PIC17C designs, offering code compatibility with older Microchip parts.
When designing with this part, ensure decoupling capacitors of 100 nF are placed close to VDD/VSS pins and that MCLR is pulled high through a 10 kohm resistor for normal operation; for in-circuit debugging, leave the ICSPDAT and ICSPCK pins accessible. Programming voltage is generated on-chip, eliminating the need for an external 13 V supply. Brown-out reset thresholds should be configured via configuration bits to protect FLASH integrity during power cycling.
Аналоги без доработки для PIC18F452T-I/L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18F452T-I/L (тот же форм-фактор и посадочное место) — отличается по Package, ADC, Operating Temperature, Mounting Type, Timers.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F452-I/L
✅ Прямая замена✓ В наличии
$6.85 / шт.
Открыть даташит →PIC18F452-E/L
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$8.4 / шт.
Открыть даташит →PIC18F448-I/L
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$11.5 / шт.
Открыть даташит →PIC18F442-I/L
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.75 / шт.
Открыть даташит →PIC18F4550-I/L
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC18F4520-I/P
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.35 / шт.
Открыть даташит →PIC18F452T-I/L Максимальные параметры и электрические характеристики
| Core Architecture | PIC18, 8-bit |
| Maximum Clock Speed | 40 MHz |
| Performance | 10 MIPS (100 ns instruction cycle) |
| Program Memory | 32 KB FLASH (16K x 16) |
| Data RAM | 1.5 KB (1536 bytes) |
| Data EEPROM | 256 bytes |
| Напряжение питания | 4.2 V to 5.5 V |
| Digital I/O Pins | 34 (5V tolerant on Port B/D) |
| ADC | 10-bit, up to 8 channels |
| Timers | 2 x 8-bit, 3 x 16-bit |
| Communication | USART (RS-232/RS-485), MSSP (SPI/I2C) |
| Рабочая температура | -40 °C to +85 °C (Industrial) |
| Корпус | 44-pin PLCC (16.59 x 16.59 mm) |
| Тип монтажа | Surface Mount |
| Instruction Set | 77 single-word instructions |
| Статус RoHS | Compliant |
Конфигурация выводов PIC18F452T-I/L
| Контакт 1 | MCLR/VPP — Master clear reset / ICSP programming voltage |
| Контакт 2 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Контакт 3 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Контакт 4 | RA2/AN2/VREF- — PORTA bit 2 / Analog input 2 / ADC VREF- |
| Контакт 5 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / ADC VREF+ |
| Контакт 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Контакт 7 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| Контакт 8 | RE0/RD/AN5 — PORTE bit 0 / Read control for PSP / Analog input 5 |
| Контакт 9 | RE1/WR/AN6 — PORTE bit 1 / Write control for PSP / Analog input 6 |
| Контакт 10 | RE2/CS/AN7 — PORTE bit 2 / Chip select for PSP / Analog input 7 |
| Контакт 11 | VDD — Positive supply voltage (4.2V-5.5V) |
| Контакт 12 | VSS — Ground reference |
| Контакт 13 | OSC1/CLKI — Oscillator crystal input / external clock input |
| Контакт 14 | OSC2/CLKO — Oscillator crystal output / clock output |
| Контакт 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output |
| Контакт 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| Контакт 17 | RC2/CCP1 — PORTC bit 2 / CCP1 PWM/capture/compare |
| Контакт 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Контакт 19 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| Контакт 20 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| Контакт 21 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| Контакт 22 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| Контакт 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Контакт 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| Контакт 25 | RC6/TX/CK — PORTC bit 6 / USART async transmit / clock |
| Контакт 26 | RC7/RX/DT — PORTC bit 7 / USART async receive / data |
| Контакт 27 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| Контакт 28 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| Контакт 29 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| Контакт 30 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| Контакт 31 | VSS — Ground reference |
| Контакт 32 | VDD — Positive supply voltage (4.2V-5.5V) |
| Контакт 33 | RB0/INT0 — PORTB bit 0 / External interrupt 0 |
| Контакт 34 | RB1/INT1 — PORTB bit 1 / External interrupt 1 |
| Контакт 35 | RB2/INT2 — PORTB bit 2 / External interrupt 2 |
| Контакт 36 | RB3/CCP2 — PORTB bit 3 / CCP2 |
| Контакт 37 | RB4 — PORTB bit 4 (interrupt-on-change) |
| Контакт 38 | RB5/PGM — PORTB bit 5 / Low-voltage ICSP programming |
| Контакт 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Контакт 40 | RB7/PGD — PORTB bit 7 / ICSP data |
| Контакт 41 | NC — Not connected (per datasheet) |
| Контакт 42 | NC — Not connected (per datasheet) |
| Контакт 43 | NC — Not connected (per datasheet) |
| Контакт 44 | NC — Not connected (per datasheet) |
Типичное применение
PIC18F452T-I/L подходит для 7 применениеs: Industrial Sensor Interface Controller, HVAC Thermostat and Building Automation, Appliance Control Board (White Goods), Portable Data Logger, HMI Panel Controller, Educational Embedded Systems Platform, Low-End Motor Control (BLDC / Stepper).
Industrial Sensor Interface Controller
The PIC18F452T-I/L is well suited to industrial sensor hubs where 34 digital I/O lines and a 10-bit ADC are needed to read multiple 4-20 mA loops, thermistors, and digital encoders. With 40 MHz operation (10 MIPS) and 32 KB FLASH, the device handles C-compiled sensor fusion, PID loops, and Modbus RTU over the hardware USART. Industrial -40 °C to +85 °C operation ensures deployment on factory floors where ambient temperatures fluctuate widely. Place the MCU on an RS-485 bus with the USART for multi-drop sensor networks.
Рекомендуется
HVAC Thermostat and Building Automation
In HVAC and building automation controllers, the PIC18F452T-I/L's 32 KB FLASH accommodates Modbus, BACnet MS-TP, and proprietary thermostat firmware while its nanoWatt Technology drops quiescent current during battery-backed thermostat standby to microamp levels. The 10-bit ADC reads thermistor temperature sensors with adequate resolution for ±0.5 °C setpoint control, and three 16-bit timers drive triac-based heater/cool actuator timing. Use MSSP in I2C mode to interface LCD keypads and external RTC chips.
Рекомендуется
Appliance Control Board (White Goods)
The PIC18F452T-I/L serves washing-machine, dishwasher, and oven control boards where its 77 single-word PIC18 instructions simplify MISRA-style safety-critical firmware in C. With 34 I/O pins it directly drives triac optocouplers, relay coils, and seven-segment LED displays without external expanders, while the 10-bit ADC monitors motor current and temperature. Industrial temperature grade handles the steam and heat of kitchen environments, and 100K FLASH endurance supports the 10-15 year field life typical of white goods.
Рекомендуется
Portable Data Logger
For battery-powered portable data loggers, the PIC18F452T-I/L's nanoWatt Technology enables sleep currents under 1 µA, allowing weeks of unattended recording from two AA cells. The 32 KB FLASH stores application code while 256 bytes of data EEPROM retains calibration constants and time stamps across battery swaps. The MSSP I2C bus interfaces to external FRAM for high-endurance log storage, and the 10-bit ADC captures analog sensor inputs at up to 100 ksps aggregate sampling.
Рекомендуется
HMI Panel Controller
In human-machine interface panels, the PIC18F452T-I/L drives character LCDs and matrix keypads via the parallel I/O ports while the USART communicates with a host PLC over RS-232 or RS-485. Its 40 MHz throughput (10 MIPS) is sufficient to debounce keypads, render menu hierarchies, and service Modbus transactions within millisecond response budgets. PIC18 code compatibility eases migration from older PIC16C/PIC17C panel designs.
Рекомендуется
Educational Embedded Systems Platform
Universities and training institutes use the PIC18F452T-I/L on development boards to teach 8-bit embedded programming, interrupts, and peripheral interfacing thanks to the PIC18 architecture's simple 77-instruction set and free MPLAB X IDE + XC8 toolchain. The 44-pin PLCC is breadboard-friendly via PLCC-to-DIP adapters, and ICSP allows live debugging without removing the part. The PIC18F452 lineage has decades of application notes, sample code, and textbook references supporting curriculum delivery.
Рекомендуется
Low-End Motor Control (BLDC / Stepper)
For cost-sensitive BLDC and stepper motor controllers under 1 kg, the PIC18F452T-I/L's three 16-bit timers generate PWM channels for H-bridge commutation and its 10-bit ADC reads back EMF sensing on three phases. The hardware USART supports RS-485 daisy-chained motor nodes, and 32 KB FLASH holds sensorless commutation tables plus a small state machine. For higher-performance FOC, designers migrate to dsPIC33 or PIC32MK families in the same Microchip ecosystem.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18F452T-I/L — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F452-I/L | PIC18F4550-I/L | PIC18F442-I/L |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-PLCC (16.59x16.59 mm) | 44-PLCC - same | 44-PLCC - same | 44-PLCC - same |
| Program FLASH | 32 KB (16K x 16) | 32 KB | 32 KB | 16 KB (-50%) |
| Data RAM | 1.5 KB (1536 B) | 1.5 KB | 2 KB (+33%) | 768 B (-49%) |
| Maximum Clock | 40 MHz (10 MIPS) | 40 MHz | 48 MHz (+20%) | 40 MHz |
| ADC Resolution | 10-bit, 8 channels | 10-bit, 8 ch | 10-bit, 13 ch | 10-bit, 8 ch |
| USB Peripheral | No | No | Yes, USB 2.0 FS | No |
| Supply Voltage | 4.2 V to 5.5 V | 4.2 V to 5.5 V | 4.2 V to 5.5 V | 4.2 V to 5.5 V |
| Industrial Temp Grade | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Ключевые отличия
- Tape-and-reel format for high-volume SMT assembly (против PIC18F452-I/L)
- On-chip USB 2.0 FS not present, but extensive general-purpose peripherals (против PIC18F4550-I/L)
- 32 KB FLASH doubles program headroom vs PIC18F442 (против PIC18F442-I/L)
- Industrial -40 °C to +85 °C operation standard (против PIC18F452-E/L)
Заметки по проектированию
Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD/VSS pin pair (pins 11/12 and 32/31 on the 44-PLCC), plus a bulk 10 µF tantalum or aluminum polymer capacitor near the IC. The PIC18F452T-I/L powers up with MCLR held low; tie MCLR to VDD through a 10 kohm resistor and add a 100 nF cap to ground for noise immunity. Brown-out reset should be enabled in configuration bits to protect FLASH integrity below 4.0 V.
Route the 40 MHz oscillator traces (OSC1/OSC2, pins 13/14) on the top layer under 1 cm of length, guard them with a GND ring, and keep high-current digital traces away. When using a crystal, place load capacitors (typically 15-33 pF) within 3 mm of the OSC pins. For best ADC accuracy, dedicate an AVSS pin trace back to a clean star-ground point; the PIC18F452 lacks dedicated AVSS but VSS at pin 12 should be the ADC reference ground.
Do not omit the MCLR pull-up resistor (10 kohm to VDD); leaving MCLR floating causes spurious resets. For in-circuit serial programming (ICSP), the RB6/PGC and RB7/PGD pins must be accessible - do not load them with heavy capacitance that slows the ICSP clock below 2 MHz. Configuration bits must be set before code execution; an unprogrammed CONFIG reads all 1s, which can disable the PLL, brown-out reset, and watchdog - often a frustrating debug-time discovery.
When the 44-pin PLCC drives long cables from USART (RS-485) or I2C (MSSP), add 100 ohm source-termination on each differential pair and a TVS diode array at the connector. The PIC18F452T-I/L does not include slew-rate control on I/O; for EMI-sensitive applications, place 100 ohm series resistors on toggling outputs. PORTB has weak internal pull-ups that can be enabled per pin in software - use them for keyswitch inputs instead of external resistors where possible.
Информация о соответствии
RoHS compliant per Microchip product page; lead-free matte-tin plating on PLCC leads. Not AEC-Q100 qualified; choose PIC18F452-E/L (extended temp) for automotive. PIC18F452 family supports IEC 60730 Class B software safety requirements for white-goods.
