PIC18F4580-E/PT - 40MHz 8-bit MCU w/ ECAN, 32KB Flash TQFP-44
Артикул: PIC18F4580-E/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.82 | $4,82 |
| 10 | $4.45 | $44,50 |
| 100 | $3.96 | $396,00 |
| 500 | $3.58 | $1.790,00 |
| 1.000 | $3.21 | $3.210,00 |
PIC18F4580-E/PT Обзор
A PIC microcontroller is a class of 8-bit Harvard-architecture microcontrollers from Microchip that combine a RISC instruction set, on-chip Flash program memory, integrated peripherals (ADC, timers, communications), and a separate data bus for instruction and data fetches. PIC microcontrollers sit within the broader taxonomy of embedded controllers -> microcontrollers (MCUs) -> microprocessors and integrated circuits (ICs), and are widely deployed in automotive, industrial, and consumer applications where deterministic real-time performance, low power, and a mature toolchain (MPLAB X IDE, MPLAB XC8 compiler, ICD in-circuit debuggers) are essential.
Key features include the ECAN module supporting CAN 2.0B active/passive with hardware filtering, Capture/Compare/PWM (CCP) and Enhanced CCP (ECCP) peripherals, two USART modules with LIN support, an MSSP module for SPI and I2C (master/slave), 36 digital I/O pins, and nanoWatt Technology with multiple power-managed modes (Run, Idle, Sleep). The integrated 10-bit ADC offers up to 13 channels and 100K samples per second, suitable for sensor signal acquisition.
The architecture is based on a 16-bit instruction word with an 8-bit data path, an internal 31-level hardware stack, and a priority-level interrupt controller. The device operates across 2.0V to 5.5V (F-range) or 4.2V to 5.5V (E-extended) supply rails, with extended temperature range of -40C to +125C for the -E variant, making it a workhorse for automotive under-hood and industrial environments. In-system programming via ICSP and ICD debug are both natively supported.
Typical applications include CAN-based automotive body and chassis networks (ECUs, instrument clusters, gateways), industrial CAN-bus nodes (sensor networks, motor control, factory automation), HVAC controls, and remote sensor data loggers. The combination of ECAN, multiple serial interfaces, and nanoWatt power modes makes it well suited to distributed nodes on a CAN network. When designing with this part, allocate the ECAN I/O pins (CANTX/CANRX) carefully because they cannot be remapped; ensure the 5V supply rail is decoupled with at least 100nF + 10uF close to the VDD pins, and follow Microchip AN1245 (ECAN) guidelines for bus termination.
Аналоги без доработки для PIC18F4580-E/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18F4580-E/PT (тот же форм-фактор и посадочное место) — отличается по Package, Core Architecture, Operating Temperature, Timers, ADC.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F4580-I/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F4680-E/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F4580T-E/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F4580-E/P
✅ Прямая замена✓ В наличии
$4.41 / шт.
Открыть даташит →PIC18F4480-E/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F4580-E/PT Максимальные параметры и электрические характеристики
| Family | PIC18F |
| Core | 8-bit PIC RISC |
| Program Memory (Flash) | 32 KB (16K x 16) |
| RAM | 1536 bytes |
| EEPROM | 256 bytes |
| Maximum Clock Speed | 40 MHz |
| MIPS | 10 MIPS |
| Supply Voltage (E - extended) | 4.2 V to 5.5 V |
| I/O Pins | 36 |
| ADC | 10-bit, up to 13 channels |
| ADC Sampling Rate | 100K samples/sec |
| CAN | ECAN (CAN 2.0B active/passive) |
| USART | 2 modules with LIN support |
| MSSP (SPI/I2C) | 1 module, SPI + I2C master/slave |
| CCP / ECCP | 1 CCP + 1 ECCP |
| Timers | 4 (Timer0/1/2/3) |
| Корпус | TQFP-44 (10x10 mm) |
| Рабочая температура | -40C to +125C (E variant) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Programming | ICSP, ICD |
Конфигурация выводов PIC18F4580-E/PT
| Контакт 1 | MCLR — Master Clear (Reset) input, active-low |
| Контакт 2 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Контакт 3 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Контакт 4 | RA2/AN2/VREF- — PORTA bit 2 / Analog input 2 / ADC VREF- |
| Контакт 5 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / ADC VREF+ |
| Контакт 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Контакт 7 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI Slave Select |
| Контакт 8 | RE0/RD/AN5 — PORTE bit 0 / Read control for Parallel Slave Port / Analog input 5 |
| Контакт 9 | RE1/WR/AN6 — PORTE bit 1 / Write control for PSP / Analog input 6 |
| Контакт 10 | RE2/CS/AN7 — PORTE bit 2 / Chip Select for PSP / Analog input 7 |
| Контакт 11 | VDD — Positive supply voltage (4.2V to 5.5V) |
| Контакт 12 | VSS — Ground reference |
| Контакт 13 | OSC1/CLKI/RA7 — Oscillator crystal input / external clock input / PORTA bit 7 |
| Контакт 14 | OSC2/CLKO/RA6 — Oscillator crystal output / clock output / PORTA bit 6 |
| Контакт 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| Контакт 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 I/O |
| Контакт 17 | RC2/CCP1 — PORTC bit 2 / ECCP1 output |
| Контакт 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Контакт 19 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Контакт 20 | RC5/SDO — PORTC bit 5 / SPI data out |
| Контакт 21 | RC6/TX/CK — PORTC bit 6 / USART1 async transmit / USART1 sync clock |
| Контакт 22 | RC7/RX/DT — PORTC bit 7 / USART1 async receive / USART1 sync data |
| Контакт 23 | RB0/INT0/FLT0 — PORTB bit 0 / External interrupt 0 / ECCP fault input |
| Контакт 24 | RB1/INT1 — PORTB bit 1 / External interrupt 1 |
| Контакт 25 | RB2/CANTX — PORTB bit 2 / ECAN transmit output |
| Контакт 26 | RB3/CANRX — PORTB bit 3 / ECAN receive input |
| Контакт 27 | RB4 — PORTB bit 4 |
| Контакт 28 | RB5/PGM — PORTB bit 5 / Low-voltage ICSP programming |
| Контакт 29 | RB6/PGC — PORTB bit 6 / ICSP clock / ICD clock |
| Контакт 30 | RB7/PGD — PORTB bit 7 / ICSP data / ICD data |
| Контакт 31 | VSS — Ground reference (second) |
| Контакт 32 | VDD — Positive supply voltage (second) |
| Контакт 33 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port data 0 |
| Контакт 34 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port data 1 |
| Контакт 35 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port data 2 |
| Контакт 36 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port data 3 |
| Контакт 37 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port data 4 |
| Контакт 38 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port data 5 |
| Контакт 39 | RD6/PSP6/TX2 — PORTD bit 6 / PSP data 6 / USART2 transmit |
| Контакт 40 | RD7/PSP7/RX2 — PORTD bit 7 / PSP data 7 / USART2 receive |
| Контакт 41 | AVDD — Analog positive supply |
| Контакт 42 | AVSS — Analog ground |
| Контакт 43 | NC — Not connected (per datasheet) |
| Контакт 44 | NC — Not connected (per datasheet) |
Типичное применение
PIC18F4580-E/PT подходит для 7 применениеs: Automotive CAN Body Electronics, Industrial CAN-Bus Sensor Nodes, HVAC Climate Control Systems, Instrument Cluster and Dashboard ECUs, Remote Sensor Data Loggers (CAN-Connected), Motor Control with CAN Feedback, Automotive Gateway and Bridge Nodes.
Automotive CAN Body Electronics
The PIC18F4580-E/PT is ideally suited for automotive body and chassis CAN nodes because its ECAN module implements CAN 2.0B active/passive with hardware acceptance filtering and three transmit mailboxes. The 36 digital I/O pins are sufficient to drive lights, switches, and relay drivers while reading digital sensors. At 40 MHz the core runs at 10 MIPS, easily handling LIN master stacks, OBD-II diagnostic framing, and CCP-based PWM fan or lighting control. The -40C to +125C extended temperature grade and 4.2 V to 5.5 V supply cover automotive 12 V rail cranking and load-dump transients when paired with a proper TVS/regulator front end. Compared with a basic 8-bit MCU without ECAN, this part eliminates the need for an external CAN controller and transceiver interface logic, reducing BOM cost and PCB area.
Рекомендуется
Industrial CAN-Bus Sensor Nodes
In distributed industrial sensor networks, the PIC18F4580-E/PT's ECAN peripheral and 10-bit 13-channel ADC make it a single-chip solution for analog-sensor-to-CAN nodes. The ADC converts at 100K samples/sec with selectable reference, while ECAN streams converted values onto the bus with hardware time-stamping. The 36 I/O support multiple digital sensors, and nanoWatt Technology (Idle/Sleep modes) reduces quiescent current for battery or solar-powered remote nodes. The TQFP-44 package is hand-solderable for prototypes yet compatible with full SMT lines for production. Compared with a 32-bit Cortex-M0 + external CAN, the 4580 saves cost and firmware complexity while delivering adequate throughput for sensor telemetry at 100 Hz update rates typical of industrial CANopen or DeviceNet nodes.
Рекомендуется
HVAC Climate Control Systems
The PIC18F4580-E/PT is well matched to HVAC control applications because of its combined ADC, ECCP PWM, and serial-interface richness. Multiple temperature/humidity sensors are digitized by the 10-bit ADC, while the ECCP drives TRIAC or IGBT gate signals for variable-speed blower and compressor control. Two USART modules support both a local HMI display (RS-232/RS-485) and a building-automation backbone (Modbus or BACnet). The 1536-byte SRAM is sufficient for scheduled-control loops, look-up tables for fan curves, and stack depth for interrupt-driven USART reception. nanoWatt Sleep mode lets the controller draw microamps during standby, an essential property for ENERGY-STAR-qualified HVAC systems. Compared with discrete logic controllers, this 4580-based design reduces component count and provides firmware-upgrade flexibility over ICSP without removing the board.
Рекомендуется
Instrument Cluster and Dashboard ECUs
The PIC18F4580-E/PT can serve as a secondary display or gauge controller in automotive dashboards, offloading graphics rendering from a host head-unit MCU via SPI/I2C. The MSSP module talks to dedicated display-driver ICs, while ECCP drives gauge stepper motors or LED backlights. ECAN receives vehicle-speed, RPM, and fuel data from the central ECU over CAN at 500 kbps. The 32KB Flash accommodates full CAN J1939 stack, gauge sweep animations, and fault-handling code. The -E temperature rating tolerates cabin-temperature swings including direct sunload up to +125C, while the 44-pin TQFP keeps the PCB compact enough to fit behind a 3.5-inch TFT. Compared with a 16-bit MCU, this 4580 base lowers cost while still meeting the real-time rendering budget for small clusters.
Рекомендуется
Remote Sensor Data Loggers (CAN-Connected)
For battery-powered remote sensor data loggers, the PIC18F4580-E/PT combines a low-power Sleep mode, ECAN for communication, and 256 bytes of EEPROM for non-volatile configuration storage. The 10-bit ADC digitizes slow-changing analog signals such as soil moisture, pressure, or temperature with programmable acquisition timing. ECAN wakes the device from Sleep via CAN activity, transmits a packet, and returns to Sleep - the entire transaction drains microamp-level current on average. The 32KB Flash accommodates TinyOS-style or custom scheduler code with over-the-air firmware update hooks over CAN. Compared with a discrete ADC + microcontroller + CAN controller design, this single-chip approach reduces PCB area by ~60% and BOM cost by ~40%.
Рекомендуется
Motor Control with CAN Feedback
The PIC18F4580-E/PT integrates ECCP for PWM generation and ECAN for closed-loop feedback, making it a unified motor-controller platform for small BLDC or stepper systems. The ECCP module generates center-aligned 10-bit PWM at up to 40 MHz timer clock with programmable dead-band delay, while ECAN streams encoder position, current, and temperature back to a supervisory controller at 1 Mbps. The ADC samples motor current via shunt resistors through the 13 available channels. The 36 I/O drive direction logic, brake, and fault inputs. The -40C to +125C range and ECAN's hardware filtering make this part suitable for industrial servo drives where determinism and bus reliability matter. Compared with using a separate PWM controller + MCU, the 4580 integration cuts component count and improves PWM-to-CAN latency consistency.
Рекомендуется
Automotive Gateway and Bridge Nodes
The PIC18F4580-E/PT's two USART modules, MSSP, and ECAN give it three independent serial interfaces, sufficient to act as a CAN-LIN-SPI gateway between sub-networks in a vehicle. The 32KB Flash fits protocol translation tables, and the 10 MIPS core executes state-machine routing with low latency. In a typical bridge use case, ECAN transports CAN frames while USART1 speaks LIN to body-control nodes and MSSP exchanges configuration with an external EEPROM or secure element. The TQFP-44 package leaves pins free for status LEDs, configuration jumpers, and an SWD-like debug header. Compared with an FPGA-based bridge, this 4580-based gateway dramatically reduces unit cost and power consumption for high-volume automotive ECUs.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18F4580-E/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F4580-I/PT | PIC18F4680-E/PT | PIC18F4580T-E/PT | PIC18F4480-E/PT |
|---|---|---|---|---|---|
| Package | TQFP-44 (10x10 mm) | TQFP-44 (10x10 mm) - same | TQFP-44 (10x10 mm) - same | TQFP-44 (10x10 mm) - same | TQFP-44 (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| Core / Architecture | 8-bit PIC18 RISC | 8-bit PIC18 RISC - same | 8-bit PIC18 RISC - same | 8-bit PIC18 RISC - same | 8-bit PIC18 RISC - same |
| Max Clock Speed | 40 MHz | 40 MHz - same | 40 MHz - same | 40 MHz - same | 40 MHz - same |
| Flash Memory | 32 KB | 32 KB - same | 64 KB (+100%) | 32 KB - same | 32 KB - same |
| RAM | 1536 bytes | 1536 bytes - same | 3328 bytes (+117%) | 1536 bytes - same | 1536 bytes - same |
| ECAN Module | Yes | Yes - same | Yes - same | Yes - same | No |
| Operating Temperature | -40C to +125C (E - extended) | -40C to +85C (I - industrial) | -40C to +125C (E - extended) | -40C to +125C (E - extended) | -40C to +125C (E - extended) |
| I/O Pins | 36 | 36 - same | 36 - same | 36 - same | 36 - same |
Ключевые отличия
- Integrated ECAN hardware (против PIC18F4480-E/PT)
- Extended temperature range for automotive/industrial (против PIC18F4580-I/PT)
- 44-pin TQFP with maximum I/O in the family (против PIC18F448-E/PT (40-pin))
Заметки по проектированию
The PIC18F4580-E/PT operates from 4.2V to 5.5V on VDD (pins 11 and 32) and AVDD (pin 41). Decouple each VDD with 100nF + 10uF ceramic placed within 5 mm of the pin, and add 10uF + 100nF on AVDD. Tie the two VSS pins (12, 31) and AVSS (pin 42) to a single ground plane, but keep analog and digital grounds separated to one point near the MCU. nanoWatt Sleep mode drops quiescent current to sub-microamp levels - use CAN message-wake or external interrupt to exit Sleep without resetting state.
The TQFP-44 package has a thermal resistance of approximately 50 C/W (theta_JA) on a standard 4-layer JEDEC test board. At maximum operating current (~50 mA active, ~1 uA Sleep) the part dissipates less than 250 mW even at 5.5 V, so no heatsink is required. However, in sealed enclosures at +125C ambient, derate the maximum clock frequency below 25 MHz if the internal die temperature approaches the +150C junction limit. Use Sleep mode aggressively to keep average die temperature low.
Route the ECAN signals (CANTX/CANRX on RB2/RB3, pins 25/26) as a short differential pair directly to the MCP2551 or similar CAN transceiver, with 120 ohm termination at each end of the bus. The ICSP pins (PGC/PGM/PGD on RB6/RB5/RB7) must be brought out to a 5-pin header for ICD debug - do not place other loads on these pins. MCLR (pin 1) requires a 10 kohm pull-up to VDD and a 100 nF decoupling cap to ground to prevent spurious resets. Keep crystal traces (OSC1/OSC2, pins 13/14) short and surrounded by ground pour.
Common pitfalls with PIC18F4580-E/PT designs: (1) Forgetting CONFIG settings - LVP must be disabled to free RB5 for digital I/O unless using low-voltage programming; (2) Leaving CANTX/CANRX as analog by default - they must be configured as digital via TRISB; (3) ECAN requires configuration of the CANCON register family before any message transmission; (4) The ADC channel AN4 shares pin RA5 with SS - disable SS by clearing TRISA bit appropriately; (5) MCLR cannot be left floating - it requires a pull-up to VDD for normal operation.
For ECAN at 1 Mbps, place the MCP2551 within 50 mm of the PIC18F4580 and add a 120 ohm resistor between CANH and CANL at the bus ends. Avoid routing CAN traces parallel to noisy switching traces; if unavoidable, increase spacing to 3x the trace height or use a guard ground trace. The MSSP SPI signals (RC3/RC4/RC5) need 33 ohm series resistors when driving more than 50 mm of trace at 10 MHz or above - this damps ringing on the SDO/SDI/SCK lines.
Информация о соответствии
RoHS compliant per Microchip product page. PIC18F4580-E/PT is not formally AEC-Q100 qualified per Microchip's automotive product catalog (qualification status varies by part number); for AEC-Q100 specifically, consult Microchip automotive-grade PIC18F parts list. Halogen-free per Microchip environmental compliance disclosure.