PIC18LF2321-I/ML - 8KB Flash 8-bit MCU, 40MHz, 28-QFN | Microchip
Артикул: PIC18LF2321-I/ML ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.42 | $3,42 |
| 10 | $3.08 | $30,80 |
| 100 | $2.74 | $274,00 |
| 500 | $2.39 | $1.195,00 |
| 1.000 | $2.1 | $2.100,00 |
PIC18LF2321-I/ML Обзор
This device is part of the PIC microcontroller family, which is a RISC (Reduced Instruction Set Computer) architecture widely used in embedded control applications. PIC microcontrollers are 8-bit MCUs that combine Flash program memory, RAM, EEPROM, configurable digital I/O, and on-chip peripherals (ADC, timers, UART, SPI, I2C) on a single chip. They sit within the broader hierarchy of microcontrollers -> microprocessors -> ICs -> semiconductors, and are favored in industrial, automotive, consumer, and IoT applications for their deterministic performance, low power, and ease of programming through MPLAB X IDE.
The PIC18LF2321-I/ML features a 10-bit ADC with up to 28 channels (varies by package), multiple capture/compare/PWM modules, an enhanced USART, MSSP (SPI/I2C) interface, and a 25 I/O pin count in the 28-QFN package. It supports a wide operating voltage range of 2.0V to 5.5V (LF variant), making it suitable for both battery-powered and 5V regulated systems. The /ML suffix indicates the 28-pin QFN industrial temperature grade (-40C to +85C).
Architecture-wise, this device uses a 16-bit-wide instruction word with an 8-bit data path, allowing most instructions to execute in a single cycle. The integrated nanoWatt Technology provides multiple power-managed modes (Idle, Sleep, and Run) for battery-sensitive designs, while the self-reprogrammable Flash under software control enables flexible field updates.
Typical applications include industrial sensor nodes, low-power IoT edge devices, battery-powered instrumentation, HVAC control, motor control loops, USB-to-UART bridges, and consumer appliances. The combination of 8 KB Flash, 25 I/O, and integrated 10-bit ADC allows engineers to replace multiple discrete components with a single chip.
Design consideration: the exposed thermal pad on the QFN package must be soldered to the PCB ground plane for proper thermal dissipation, RF performance, and mechanical reliability. Always follow Microchip's QFN PCB layout guidelines to avoid solder joint fatigue.
This page synthesizes distributor pricing, drop-in alternative MPNs from the Microchip PIC18 family, and practical design notes not aggregated on the manufacturer product page.
Аналоги без доработки для PIC18LF2321-I/ML — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18LF2321-I/ML (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, ADC, Core, I/O Pins.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18LF2320-I/ML
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F2321-I/ML
✅ Прямая замена✓ В наличии
$3.17 / шт.
Открыть даташит →PIC18LF2221-I/ML
✅ Прямая замена✓ В наличии
$1.4 / шт.
Открыть даташит →PIC18LF2220-I/ML
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC18LF2321-I/ML Максимальные параметры и электрические характеристики
| Core | PIC 8-bit RISC |
| Instruction Set Width | 16-bit |
| Program Memory (Flash) | 8 KB (4K x 16) |
| Data RAM | 512 bytes |
| Data EEPROM | 256 bytes |
| Maximum CPU Speed | 40 MHz (10 MIPS) |
| Operating Voltage | 2.0 V to 5.5 V |
| I/O Pins | 25 |
| ADC | 10-bit, up to 28 channels |
| Communication Interfaces | EUSART, MSSP (SPI/I2C) |
| Корпус | 28-QFN (6x6 mm) with exposed pad |
| Рабочая температура | -40C to +85C (Industrial) |
| Тип монтажа | Surface Mount |
| Power-Saving Modes | nanoWatt Technology (Idle / Sleep / Run) |
Конфигурация выводов PIC18LF2321-I/ML
| Контакт 1 | RA0/AN0 — Digital I/O / Analog input channel 0 |
| Контакт 2 | RA1/AN1 — Digital I/O / Analog input channel 1 |
| Контакт 3 | RA2/AN2/VREF- — Digital I/O / Analog input / ADC VREF- |
| Контакт 4 | RA3/AN3/VREF+ — Digital I/O / Analog input / ADC VREF+ |
| Контакт 5 | RA4 — Digital I/O (open-drain) |
| Контакт 6 | RA5/AN4 — Digital I/O / Analog input channel 4 |
| Контакт 7 | VSS — Ground reference |
| Контакт 8 | OSC1/CLKIN — Crystal oscillator input / external clock |
| Контакт 9 | OSC2/CLKOUT — Crystal oscillator output |
| Контакт 10 | RC0 — Digital I/O / PWM output |
| Контакт 11 | RC1 — Digital I/O / PWM output |
| Контакт 12 | RC2/CCP1 — Digital I/O / Capture-Compare-PWM 1 |
| Контакт 13 | RC3 — Digital I/O / SPI/I2C clock |
| Контакт 14 | RC4 — Digital I/O / SPI/I2C data |
| Контакт 15 | RC5 — Digital I/O / SPI/I2C data |
| Контакт 16 | RC6/TX — Digital I/O / EUSART TX |
| Контакт 17 | RC7/RX — Digital I/O / EUSART RX |
| Контакт 18 | RB0/INT0 — Digital I/O / External interrupt 0 |
| Контакт 19 | RB1/INT1 — Digital I/O / External interrupt 1 |
| Контакт 20 | RB2 — Digital I/O |
| Контакт 21 | RB3 — Digital I/O |
| Контакт 22 | RB4 — Digital I/O |
| Контакт 23 | RB5 — Digital I/O |
| Контакт 24 | RB6/PGC — Digital I/O / ICSP clock |
| Контакт 25 | RB7/PGD — Digital I/O / ICSP data |
| Контакт 26 | VDD — Positive supply (2.0-5.5 V) |
| Контакт 27 | VSS — Ground reference |
| Контакт 28 | MCLR/VPP — Master clear reset (active-low) / programming voltage |
Типичное применение
PIC18LF2321-I/ML подходит для 6 применениеs: Industrial Sensor Hubs, Battery-Powered IoT Edge Nodes, HVAC and Building Control, Consumer Appliance Control, Motor Control and PWM Drivers, Automotive Aftermarket Accessories.
Industrial Sensor Hubs
The PIC18LF2321-I/ML fits industrial sensor hubs because its 25 I/O pins and 10-bit ADC let it aggregate multiple analog sensors (temperature, pressure, humidity) in a single chip. The 2.0-5.5 V supply range lets it run from a 24V industrial rail with a small LDO, while the 8 KB Flash holds protocol stacks for 4-20 mA loop output or Modbus framing. Its nanoWatt sleep mode drops quiescent current to the nA range between sensor reads, suiting remote solar-powered installations.
Рекомендуется
Battery-Powered IoT Edge Nodes
The PIC18LF2321-I/ML's wide 2.0-5.5 V supply range and nanoWatt sleep technology make it a strong choice for battery-powered IoT edge nodes that wake periodically to read sensors and transmit. The 8 KB Flash accommodates lightweight wireless stacks (LoRaWAN, BLE beaconing) and the 512 B RAM is sufficient for short packet buffers. At deep sleep with RTC tick at 32 kHz, the chip draws sub-microamp current, extending coin-cell or 2x AA battery life to multiple years.
Рекомендуется
HVAC and Building Control
The PIC18LF2321-I/ML fits HVAC and building automation controllers because its 25 I/O can drive relays, triacs, and valve actuators while the 10-bit ADC reads thermistor/resistive temperature sensors. The wide operating temperature of -40C to +85C suits unconditioned equipment closets, and the 5V tolerance integrates directly with legacy thermostat wiring. The 8 KB Flash holds proportional-integral control loops and 7-day scheduling logic for smart thermostats.
Рекомендуется
Consumer Appliance Control
The PIC18LF2321-I/ML is well-suited to consumer appliance main-control boards (coffee machines, small kitchen appliances, washing-machine user-interface panels). Its EUSART and MSSP blocks drive character LCDs and capacitive touch controllers, while the 8 KB Flash supports user-interface state machines and safety logic. The industrial temperature grade and surface-mount QFN package meet reliability requirements for white goods.
Рекомендуется
Motor Control and PWM Drivers
The PIC18LF2321-I/ML's enhanced CCP/ECCP modules deliver PWM outputs suitable for brushed DC and small stepper motor control in toys, small fans, and valve actuators. The 40 MHz core closes PID loops fast enough for sub-millisecond update rates, while the 25 I/O pins carry encoder feedback, limit switches, and H-bridge control signals. Pairing with Microchip's TC4469 gate driver provides robust MOSFET switching for brushed DC motors up to several amps.
Рекомендуется
Automotive Aftermarket Accessories
The PIC18LF2321-I/ML powers automotive aftermarket accessories such as auxiliary lighting controllers, alarm-system interfaces, and OBD-II loggers. Its 2.0-5.5 V supply tolerates 12V battery cranking transients when paired with a TVS diode and LDO. The industrial temperature grade suits cabin and engine-bay installations, while the 8 KB Flash holds CAN/LIN framing libraries and diagnostic-logging routines for aftermarket telematics.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18LF2321-I/ML — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18LF2320-I/ML | PIC18F2321-I/ML | PIC18LF2221-I/ML | PIC18LF2220-I/ML |
|---|---|---|---|---|---|
| Package | 28-QFN (6x6 mm) | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 8 KB | 8 KB | 8 KB | 2 KB | 2 KB |
| Operating Voltage | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 4.2 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| I/O Pins | 25 | 25 | 25 | 25 | 25 |
| CPU Speed | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS |
| ADC | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit |
| Unit Price (qty 1, as of 2026-09-28) | $3.42 | ~$3.30 | ~$3.50 | ~$2.40 | ~$2.30 |
Ключевые отличия
- Wider supply range than PIC18F2321-I/ML (против PIC18F2321-I/ML)
- More Flash than PIC18LF2221-I/ML (против PIC18LF2221-I/ML)
- Includes second analog comparator missing from PIC18LF2320-I/ML (против PIC18LF2320-I/ML)
- Industrial -40C to +85C operation (против PIC18F2321T-I/ML (extended temp variant))
Заметки по проектированию
The 28-QFN exposed thermal pad must be soldered to a continuous ground copper pour on the PCB. Microchip recommends at least 16 thermal vias (0.3 mm drill, 1.0 mm pitch) connecting the pad to internal ground planes. Without proper soldering, the part's mechanical reliability drops sharply and ground return impedance for analog peripherals rises, increasing ADC noise. Always follow Microchip application note AN233 for QFN PCB layout.
Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of each VDD pin, plus a bulk 10 uF tantalum or aluminum polymer capacitor on the supply rail. For ADC accuracy, place a ferrite bead between digital and analog VDD rails when the board has switching converters nearby. The /ML suffix indicates industrial temperature range, so verify capacitor dielectric (X5R/X7R) supports -40C operation if exposed to cold environments.
Do not leave the MCLR pin floating. Tie MCLR to VDD through a 10 kohm pull-up resistor, with an optional 100 nF cap to VSS for noise immunity. Programming failures and spurious resets are almost always traceable to a missing or undersized MCLR pull-up. Also, ensure the PGC/PGD pins (RB6/RB7) are not loaded by external pull-ups that exceed 10 kohm, or ICSP programming will fail.
When using the ADC, source impedance should be below 10 kohm to avoid conversion errors caused by the Sample-and-Hold capacitor charging incompletely. Add an op-amp buffer (e.g., MCP6001) when reading high-impedance sensors. Keep analog traces short and routed over a continuous ground plane to minimize ADC noise coupling from digital I/O switching.
Информация о соответствии
RoHS and lead-free compliance assumed for active Microchip PIC18 family parts; AEC-Q100 not applicable (industrial grade, not automotive qualified - Microchip does not publish Q100 status for this part).
