PIC18LF2455-I/SP - 8-bit MCU 48MHz 24KB Flash FS-USB SPDIP-28
Артикул: PIC18LF2455-I/SP ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $7.1 | $7,10 |
| 10 | $6.4 | $64,00 |
| 100 | $5.55 | $555,00 |
| 500 | $4.95 | $2.475,00 |
| 1.000 | $4.45 | $4.450,00 |
PIC18LF2455-I/SP Обзор
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, Flash program memory, RAM, EEPROM, and peripherals on one die. The PIC18 family uses an enhanced RISC architecture with 16-bit instructions and 8-bit data paths, positioned between PIC16 mid-range parts and PIC32 32-bit parts in Microchip's portfolio. Microcontrollers sit below microprocessors in the compute hierarchy, providing deterministic, low-power embedded control for appliances, sensors, and USB peripherals.
Key specifications include 48 MHz maximum CPU clock (12 MIPS), 24 KB Flash (12K x 16 words), 2048 bytes SRAM, 256 bytes EEPROM, 16-bit digital I/O, 10-channel 10-bit ADC, two analog comparators, one Enhanced USART, one MSSP (I2C/SPI), a Full-Speed USB 2.0 SIE (12 Mbit/s), and 5 PWM/CCP/ECCP channels. NanoWatt power management offers idle, sleep, and ultra-low-power wake features. Internal oscillator accuracy is typically within +/-2% across voltage and temperature.
The architecture combines a Harvard bus with on-chip hardware multiply, allowing single-cycle math operations on 8-bit data. The integrated USB transceiver eliminates external PHY/clock components; firmware implements the USB stack via the Microchip USB framework, supporting HID, CDC, MSD, and custom classes. The device is industrial-grade (-40C to +85C, "I" suffix) and is a popular choice for legacy and hobby-grade USB peripherals.
Typical applications include low-cost USB HID peripherals (keyboards, mice, game controllers), USB-to-UART bridges, CDC virtual COM ports, sensor data loggers, educational development boards (such as PICDEM FSUSB), and industrial HMI panels. The wide 2.0-5.5 V supply range simplifies integration into both 3.3 V and 5 V systems without level shifters.
When designing with this part, ensure USB DP/DM trace impedance matches 90 ohm differential and that the VUSB pin is tied to the internal 3.3 V regulator output or a clean external 3.3 V rail. Firmware must drive the UCREGEN and UTRDIS bits correctly and provide adequate bulk capacitance on VUSB.
This page synthesizes verified distributor pricing, same-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для PIC18LF2455-I/SP — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18LF2455-I/SP (тот же форм-фактор и посадочное место) — отличается по Package, Timers, ADC, I/O Pins, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F2455-I/SP
✅ Прямая замена✓ В наличии
$4.65 / шт.
Открыть даташит →PIC18F2550-I/SP
✅ Прямая замена✓ В наличии
$4.1 / шт.
Открыть даташит →PIC18F2553-I/SP
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F2450-I/SP
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC18LF2458-I/SP
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC18LF2455-I/SP Максимальные параметры и электрические характеристики
| Core Architecture | PIC18 8-bit enhanced RISC |
| Program Memory (Flash) | 24 KB (12K x 16 words) |
| Data SRAM | 2048 bytes |
| Data EEPROM | 256 bytes |
| Maximum CPU Clock | 48 MHz (12 MIPS) |
| Operating Voltage (Vdd) | 2.0 V to 5.5 V |
| Digital I/O Pins | 16 (multiplexed with peripherals) |
| ADC | 10 channels x 10-bit |
| Analog Comparators | 2 |
| PWM Channels (CCP/ECCP) | 5 |
| Timers | 4 (Timer0/1/2/3) |
| Communication Interfaces | USB FS 2.0, EUSART, MSSP (I2C/SPI) |
| USB Transceiver | Integrated Full-Speed 12 Mbit/s SIE |
| Корпус | SPDIP-28 (/SP) |
| Operating Temperature (I suffix) | -40C to +85C (industrial) |
| Тип монтажа | Through-Hole (DIP) |
| Статус RoHS | Compliant (lead-free /SP marking) |
| Уровень MSL | 1 (not moisture-sensitive, through-hole) |
Конфигурация выводов PIC18LF2455-I/SP
| Контакт 1 | MCLR/RE3 — Master Clear (reset) input / digital input only on PORTE |
| Контакт 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Контакт 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Контакт 4 | RA2/AN2/Vref- — PORTA bit 2 / analog input 2 / ADC negative reference |
| Контакт 5 | RA3/AN3/Vref+ — PORTA bit 3 / analog input 3 / ADC positive reference |
| Контакт 6 | RA4/T0CKI/RCV — PORTA bit 4 / Timer0 clock input / USB RCV |
| Контакт 7 | RA5/AN4/SS/HLVDIN/RC2OUT — PORTA bit 5 / analog 4 / SPI SS / HLVD input / USB RC2OUT |
| Контакт 8 | Vss — Ground reference |
| Контакт 9 | OSC1/CLKI/RA7 — Crystal oscillator input / external clock / PORTA bit 7 |
| Контакт 10 | OSC2/CLKO/RA6 — Crystal oscillator output / clock out / PORTA bit 6 |
| Контакт 11 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock input |
| Контакт 12 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 PWM output |
| Контакт 13 | RC2/CCP1/P1A — PORTC bit 2 / CCP1 PWM output / PWM P1A |
| Контакт 14 | Vusb — USB internal 3.3V regulator output |
| Контакт 15 | RC4/D-/VM — PORTC bit 4 / USB D- / external USB monitor input |
| Контакт 16 | RC5/D+/VP — PORTC bit 5 / USB D+ / external USB monitor input |
| Контакт 17 | Vss — Ground reference |
| Контакт 18 | RC6/TX/CK — PORTC bit 6 / EUSART TX / EUSART clock |
| Контакт 19 | RC7/RX/DT/SDO — PORTC bit 7 / EUSART RX / EUSART data / SPI SDO |
| Контакт 20 | Vdd — Positive supply (2.0-5.5V) |
| Контакт 21 | RB0/AN12/INT0/FLT0 — PORTB bit 0 / analog 12 / external interrupt 0 / PWM fault |
| Контакт 22 | RB1/AN10/INT1 — PORTB bit 1 / analog 10 / external interrupt 1 |
| Контакт 23 | RB2/AN8/INT2/VMO — PORTB bit 2 / analog 8 / external interrupt 2 / USB VMO |
| Контакт 24 | RB3/AN9/CCP2/VPO — PORTB bit 3 / analog 9 / CCP2 / USB VPO |
| Контакт 25 | RB4/AN11/KBI0 — PORTB bit 4 / analog 11 / interrupt-on-change KBI0 |
| Контакт 26 | RB5/KBI1/PGM — PORTB bit 5 / KBI1 / LVP programming data |
| Контакт 27 | RB6/KBI2/PGC — PORTB bit 6 / KBI2 / ICSP clock |
| Контакт 28 | RB7/KBI3/PGD — PORTB bit 7 / KBI3 / ICSP data |
Типичное применение
PIC18LF2455-I/SP подходит для 6 применениеs: USB HID Peripheral (Keyboard / Mouse / Game Controller), USB-to-UART Bridge / CDC Virtual COM Port, Industrial Sensor Data Logger with USB Output, Educational Microcontroller Development Board, HMI Front Panel with USB Diagnostics Port, Custom USB Mass Storage / Custom Class Device.
USB HID Peripheral (Keyboard / Mouse / Game Controller)
The PIC18LF2455-I/SP's integrated Full-Speed USB 2.0 SIE eliminates the need for an external PHY chip, making it ideal for low-cost USB HID devices. Its 48 MHz CPU clock and 24 KB Flash comfortably fit HID report descriptors, debounce logic, and macro layers for keyboards or gaming controllers. The 2.0-5.5 V supply range supports both bus-powered 5 V and battery-powered 3.3 V designs, while the 16 I/O pins are sufficient for matrix-scanned key arrays.
Рекомендуется
USB-to-UART Bridge / CDC Virtual COM Port
The PIC18LF2455-I/SP's integrated USB transceiver plus EUSART make it well-suited for USB-to-UART bridges used as virtual COM ports in industrial and embedded applications. Its 48 MHz bus delivers reliable CDC throughput at full USB FS 12 Mbit/s, while the LF voltage variant operates from a single 3.3 V rail without an LDO. Firmware using Microchip's CDC stack achieves transparent UART tunneling with baud rates up to 921600 bps.
Рекомендуется
Industrial Sensor Data Logger with USB Output
The PIC18LF2455-I/SP's 10-channel 10-bit ADC and 24 KB Flash support multi-sensor data logging with USB dump capability for factory diagnostics. Its 2 KB RAM enables buffering of acquisition samples before USB transfer, while industrial -40C to +85C temperature operation suits factory-floor enclosures. NanoWatt sleep modes extend battery life between log sessions in portable units.
Рекомендуется
Educational Microcontroller Development Board
The PIC18LF2455-I/SP's through-hole SPDIP-28 package and integrated USB make it a teaching-friendly part for courses on embedded C, USB protocols, and PIC assembly. Hobbyists and universities benefit from breadboard-friendly pinout and Microchip's free MPLAB X IDE. Its low cost and wide hobby community reduce the learning curve for first-time MCU users exploring USB peripheral development.
Рекомендуется
HMI Front Panel with USB Diagnostics Port
The PIC18LF2455-I/SP's 5 PWM channels drive LED dimmers or backlights, while the integrated USB allows field technicians to attach a laptop for diagnostics on industrial front panels. Its analog comparators monitor voltage rails, and the 16 I/O can scan button matrices or rotary encoders. The LF voltage variant permits battery backup for parameter retention in field-deployable HMI units.
Рекомендуется
Custom USB Mass Storage / Custom Class Device
The PIC18LF2455-I/SP can implement USB Mass Storage (MSD), CDC+MSD composite, or fully custom USB classes for proprietary host software. Microchip's free USB stack supports bulk transfers up to the FS USB 2.0 ceiling. The 2 KB SRAM provides the endpoint buffer space needed for sector-level transfers, while 24 KB Flash holds both the bootloader and the application code comfortably.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18LF2455-I/SP — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F2455-I/SP | PIC18F2550-I/SP | PIC18F2553-I/SP | PIC18F2450-I/SP | PIC18LF2458-I/SP |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SPDIP-28 (/SP) | SPDIP-28 - same | SPDIP-28 - same | SPDIP-28 - same | SPDIP-28 - same | SPDIP-28 - same |
| Flash Memory | 24 KB | 24 KB | 32 KB (+33%) | 32 KB (+33%) | 16 KB (-33%) | 24 KB |
| SRAM | 2048 B | 2048 B | 2048 B | 2048 B | 2048 B | 2048 B |
| Operating Voltage | 2.0-5.5 V | 4.2-5.5 V (no LF) | 4.2-5.5 V | 4.2-5.5 V | 2.0-5.5 V | 2.0-5.5 V |
| USB 2.0 FS Transceiver | Yes (integrated) | Yes | Yes | Yes | No | Yes |
| ADC Channels | 10 x 10-bit | 10 x 10-bit | 10 x 10-bit | 8 x 10-bit | 10 x 10-bit | 10 x 10-bit |
| Maximum CPU Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
Ключевые отличия
- Integrated Full-Speed USB 2.0 transceiver with on-chip DP/DM (против PIC18F2450-I/SP)
- Wide 2.0-5.5 V operating voltage (LF variant) (против PIC18F2455-I/SP)
- 24 KB Flash with 256-byte EEPROM in the same die (против PIC18F2550-I/SP)
Заметки по проектированию
The PIC18LF2455-I/SP accepts 2.0-5.5 V on Vdd (pin 20), but the USB transceiver requires a clean 3.3 V rail from the internal Vusb regulator (pin 14). According to the Microchip DS39632 datasheet, you must place a 220 nF decoupling capacitor on Vusb and a 0.1 uF plus 10 uF bulk capacitor on Vdd. Powering the device from a noisy switching rail without input filtering may corrupt USB packets; a ferrite bead or LDO upstream of Vdd is recommended for bus-powered designs.
Route USB D+/D- (RC4/RC5, pins 15/16) as a 90 ohm differential pair with controlled impedance; keep traces under 50 mm and match lengths to within 2 mm. Place the 27 ohm series resistors on D+ and D- within 4 mm of the MCU pins. According to USB 2.0 FS signal-integrity guidelines, an unshielded cable plus mismatched impedance causes enumeration failures and intermittent disconnects. Avoid routing USB traces near oscillator or PWM-switching signals.
Do not leave MCLR (pin 1) floating. According to the Microchip DS39632 datasheet, MCLR must be tied to Vdd through a 10 kohm resistor for normal operation, or driven low for external reset. A floating MCLR may cause random resets or programming failures. Also configure the CONFIG3H register to disable the internal MCLR if you are using pin 1 as a digital input on PORTE3.
For reliable USB Full-Speed operation, ensure the internal 48 MHz PLL is stable before asserting the USB module enable bit (UCON.USBEN). According to DS39632, the firmware must poll the PLL lock status bit (OSCCON.PLLRDY) and wait at least 2 ms after start-up for the PLL to settle. Connecting a USB host while the PLL is unstable causes enumeration errors visible in host logs as 'Device Descriptor Request Failed'.
Информация о соответствии
RoHS and REACH compliant per Microchip material declarations; lead-free /SP marking confirmed in DS39632 ordering information. Not AEC-Q100 qualified; for automotive applications select a Q-grade variant.
