PIC24EP128GP204-E/TL - 16-bit 70 MIPS MCU, 128KB Flash | Microchip
Артикул: PIC24EP128GP204-E/TL ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $5.42 | $5,42 |
| 10 | $4.88 | $48,80 |
| 100 | $4.31 | $431,00 |
| 500 | $3.82 | $1.910,00 |
| 1.000 | $3.45 | $3.450,00 |
PIC24EP128GP204-E/TL Обзор
A 16-bit microcontroller (MCU) is a programmable processor that integrates a CPU core, volatile and non-volatile memory, and a rich set of peripherals (ADC, timers, communication interfaces) into a single chip. PIC24E-series MCUs occupy the mid-performance tier of Microchip's dsPIC/PIC24 lineup, sitting between 8-bit PIC MCUs and the higher-end dsPIC33 digital signal controllers, optimized for code density, deterministic interrupt response, and advanced analog integration.
Key differentiating features include a 10/12-bit ADC with up to 1.1 Msps conversion rate, up to four on-chip operational amplifiers (Op Amps), a Charge Time Measurement Unit (CTMU) for capacitive touch and accurate time measurement, a Peripheral Trigger Generator (PTG) for hardware-state-machine automation, and four standard 16-bit timers. Communication peripherals cover up to two UART, two SPI, and two I2C interfaces, plus a Parallel Master Port for external memory expansion.
Architecturally, the PIC24E core uses a modified Harvard architecture with 16-bit data paths, a 24-bit instruction word, and a 16x16 hardware multiplier that sustains the 70 MIPS throughput at 70 MHz CPU clock. The integrated Op Amps are routed to dedicated ADC channels, eliminating external signal conditioning in motor-control and sensor-interface designs.
Typical uses include automotive body and chassis modules, industrial motor control, sensor signal conditioning, and low-cost DSP-adjacent applications such as digital filtering and PID control loops. Designers choose the -E/TL grade specifically when AEC-Q100 qualification and the compact VTLA-44 package are required for space-constrained or automotive-grade layouts.
When designing with this device, allocate sufficient PCB copper beneath the exposed thermal pad (EP) to meet the package's thermal resistance specifications, and confirm the supply voltage stays within the 3.0V to 3.6V window; dropouts below 3.0V will trigger the brown-out reset. The Peripheral Trigger Generator (PTG) is often overlooked and can offload complex sequencing from the CPU, freeing MIPS for application logic.
This page synthesizes distributor pricing for the PIC24EP128GP204-E/TL, parametric drop-in alternatives within the VTLA-44 footprint, and practical design notes not consolidated in the manufacturer datasheet.
Аналоги без доработки для PIC24EP128GP204-E/TL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC24EP128GP204-E/TL (тот же форм-фактор и посадочное место) — отличается по ADC, Package, Core Architecture, CTMU, Comparators.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC24EP128GP204-E/PT
✅ Прямая замена✓ В наличии
$4.25 / шт.
Открыть даташит →PIC24EP128GP204-E/MV
✅ Прямая замена✓ В наличии
$5.42 / шт.
Открыть даташит →PIC24EP128GP204-I/ML
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC24EP128GP204T-I/TL
✅ Прямая замена✓ В наличии
$3.33 / шт.
Открыть даташит →PIC24EP128GP204-I/PT
✅ Прямая замена✓ В наличии
$4.12 / шт.
Открыть даташит →PIC24EP128GP204-E/TL Максимальные параметры и электрические характеристики
| Core Architecture | PIC24E 16-bit modified Harvard |
| CPU Speed (MIPS) | 70 MIPS at 70 MHz |
| Flash Program Memory | 128 KB (43K x 24 instructions) |
| RAM | 16 KB |
| Operating Voltage (VDD) | 3.0 V to 3.6 V |
| Operating Temperature (E grade) | -40C to +125C |
| Корпус | 44-pin VTLA (6x6 mm) with Exposed Pad |
| Тип монтажа | Surface Mount |
| On-chip Op Amps | Up to 4 |
| CTMU (Charge Time Measurement Unit) | Yes |
| Peripheral Trigger Generator (PTG) | Yes |
| Timers | 4 x 16-bit |
| UART | Up to 2 |
| SPI | Up to 2 |
| I2C | Up to 2 |
| Parallel Master Port (PMP) | Yes |
| AEC-Q100 Qualification | Yes (automotive grade) |
| Статус RoHS | Compliant |
Конфигурация выводов PIC24EP128GP204-E/TL
| Контакт 1 | RP0/AN0/C1IN+ — Remappable I/O, analog input 0, comparator input |
| Контакт 2 | RP1/AN1/C1IN- — Remappable I/O, analog input 1, comparator input |
| Контакт 3 | RP2/AN2/C2IN+ — Remappable I/O, analog input 2, comparator input |
| Контакт 4 | RP3/AN3/C2IN- — Remappable I/O, analog input 3, comparator input |
| Контакт 5 | VDD — Positive supply voltage (3.0V to 3.6V) |
| Контакт 6 | VSS — Ground reference |
| Контакт 7 | OSC1/CLKI — Crystal oscillator input or external clock input |
| Контакт 8 | OSC2/CLKO — Crystal oscillator output or clock output |
| Контакт 9 | MCLR — Master clear reset (active low) |
| Контакт 10 | PGED2/AN4 — Programming data and analog input |
| Контакт 11 | PGEC2/AN5 — Programming clock and analog input |
| Контакт 12 | RP4/AN6/C3IN+ — Remappable I/O, analog input 6, comparator input |
| Контакт 13 | RP5/AN7/C3IN- — Remappable I/O, analog input 7, comparator input |
| Контакт 14 | RP6/AN8/OC1 — Remappable I/O, analog input 8, output compare 1 |
| Контакт 15 | RP7/AN9/OC2 — Remappable I/O, analog input 9, output compare 2 |
| Контакт 16 | RP8/U1CTS/AN10 — Remappable I/O, UART1 CTS, analog input 10 |
| Контакт 17 | RP9/U1RTS/AN11 — Remappable I/O, UART1 RTS, analog input 11 |
| Контакт 18 | VDD — Positive supply voltage |
| Контакт 19 | VSS — Ground reference |
| Контакт 20 | RP10/U1RX/C1OUT — Remappable I/O, UART1 RX, comparator 1 output |
| Контакт 21 | RP11/U1TX/C2OUT — Remappable I/O, UART1 TX, comparator 2 output |
| Контакт 22 | RP12/U2RX/C3OUT — Remappable I/O, UART2 RX, comparator 3 output |
| Контакт 23 | RP13/U2TX — Remappable I/O, UART2 TX |
| Контакт 24 | RP14/SCK1/CN0 — Remappable I/O, SPI1 clock, change notification 0 |
| Контакт 25 | RP15/SDI1/CN1 — Remappable I/O, SPI1 data in, change notification 1 |
| Контакт 26 | RP16/SDO1/CN2 — Remappable I/O, SPI1 data out, change notification 2 |
| Контакт 27 | RP17/SS1/CN3 — Remappable I/O, SPI1 slave select, change notification 3 |
| Контакт 28 | RP18/SCK2/CN4 — Remappable I/O, SPI2 clock, change notification 4 |
| Контакт 29 | RP19/SDI2/CN5 — Remappable I/O, SPI2 data in, change notification 5 |
| Контакт 30 | RP20/SDO2/CN6 — Remappable I/O, SPI2 data out, change notification 6 |
| Контакт 31 | RP21/SS2/CN7 — Remappable I/O, SPI2 slave select, change notification 7 |
| Контакт 32 | RP22/SDA1/OC3 — Remappable I/O, I2C1 SDA, output compare 3 |
| Контакт 33 | RP23/SCL1/OC4 — Remappable I/O, I2C1 SCL, output compare 4 |
| Контакт 34 | RP24/SDA2/INT0 — Remappable I/O, I2C2 SDA, external interrupt 0 |
| Контакт 35 | RP25/SCL2/INT1 — Remappable I/O, I2C2 SCL, external interrupt 1 |
| Контакт 36 | RP26/T1CK/IC1 — Remappable I/O, timer1 clock, input capture 1 |
| Контакт 37 | RP27/T2CK/IC2 — Remappable I/O, timer2 clock, input capture 2 |
| Контакт 38 | RP28/T3CK/OCFA — Remappable I/O, timer3 clock, OC fault A |
| Контакт 39 | RP29/T4CK/OCFB — Remappable I/O, timer4 clock, OC fault B |
| Контакт 40 | RP30/OC5/INT2 — Remappable I/O, output compare 5, external interrupt 2 |
| Контакт 41 | RP31/OC6/INT3 — Remappable I/O, output compare 6, external interrupt 3 |
| Контакт 42 | PMA0/RE0 — Parallel master port address 0 |
| Контакт 43 | PMA1/RE1 — Parallel master port address 1 |
| Контакт 44 | VDDCORE/VCAP — Internal voltage regulator output, decoupling cap |
Типичное применение
PIC24EP128GP204-E/TL подходит для 7 применениеs: Automotive Body and Chassis Control, Industrial Sensor Signal Conditioning, BLDC and PMSM Motor Control, Medical Patient Monitoring Devices, Building Automation and HVAC Controllers, Consumer Appliance Control, Solar Inverter and Power Conversion Control.
Automotive Body and Chassis Control
The PIC24EP128GP204-E/TL is well suited for automotive body and chassis modules where AEC-Q100 qualification and the extended -40C to +125C operating range are mandatory. The integrated on-chip Op Amps can condition H-bridge current-sense signals directly into the 12-bit ADC, eliminating external amplifiers and reducing BOM cost in body-control modules (BCMs), door-zone controllers, and lighting controllers. The 70 MIPS core sustains CAN/LIN message handling while running application state machines. Its Peripheral Trigger Generator (PTG) can offload repetitive I/O sequencing from the CPU, freeing bandwidth for diagnostic and security tasks.
Рекомендуется
Industrial Sensor Signal Conditioning
The PIC24EP128GP204-E/TL's four on-chip Op Amps and 10/12-bit ADC (up to 1.1 Msps) make it ideal for industrial sensor signal-conditioning front-ends. Engineers can connect thermocouples, strain gauges, and load cells directly to the on-chip amplifiers without external instrumentation amplifiers, then digitize via the integrated ADC. The CTMU (Charge Time Measurement Unit) supports accurate temperature and capacitance measurements. The compact VTLA-44 (6x6 mm) package is well suited to small-form-factor analog sensor modules, and the AEC-Q100 grade allows deployment in factory-floor environments with extended temperature ranges.
Рекомендуется
BLDC and PMSM Motor Control
The PIC24EP128GP204-E/TL provides the CPU throughput and analog integration required for sensorless BLDC/PMSM motor control. Its 70 MIPS core executes Field-Oriented Control (FOC) algorithms in real time at switching frequencies above 20 kHz, while the on-chip Op Amps condition phase-current sense signals. The PTG automates ADC-trigger sequencing relative to PWM edges, eliminating jitter. The automotive grade allows the same firmware image to be used across industrial and automotive product lines, simplifying design reuse.
Рекомендуется
Medical Patient Monitoring Devices
The PIC24EP128GP204-E/TL's extended operating range and integrated analog peripherals make it a candidate for portable patient monitoring equipment such as pulse oximeters, blood-pressure cuffs, and body-worn activity trackers. The on-chip Op Amps interface with optical and pressure sensors without external instrumentation amplifiers. With 128 KB Flash and 16 KB RAM, the device supports real-time DSP filtering (heart-rate detection, SpO2 calculation) on the 70 MIPS core while still leaving room for wireless-stack integration. Compliance decisions remain the integrator's responsibility under IEC 60601-1.
Рекомендуется
Building Automation and HVAC Controllers
The PIC24EP128GP204-E/TL is well suited for building-automation controllers driving HVAC actuators, fan-speed controllers, and smart thermostats. Its 70 MIPS core runs PID control loops for valve and damper positioning while the multiple UART/SPI/I2C interfaces connect to sensor networks, display modules, and wireless transceivers. The extended -E temperature grade supports installation in attic and rooftop enclosures. The CTMU provides a built-in capacitive touch controller for front-panel buttons without extra ICs.
Рекомендуется
Consumer Appliance Control
The PIC24EP128GP204-E/TL targets the user-interface and motor-control subsystems of consumer appliances such as washing machines, dishwashers, and induction cooktops. Its 70 MIPS core can drive a TFT LCD via the Parallel Master Port while simultaneously handling encoder inputs, sensor reads, and AC-phase control. The wide Flash budget (128 KB) accommodates graphical UI firmware libraries, and the AEC-Q100 grade allows operation in the high-temperature regions near heating elements. Multiple communication ports support Wi-Fi/BLE modules for IoT-connected appliances.
Рекомендуется
Solar Inverter and Power Conversion Control
The PIC24EP128GP204-E/TL is used in solar micro-inverters and small power-conversion stages where the integrated Op Amps sense inductor current and the PTG synchronizes ADC sampling to PWM events. The 70 MIPS core supports MPPT algorithms and grid-synchronization logic, while the 128 KB Flash accommodates state-machine firmware with safety routines. The wide -40C to +125C range handles outdoor rooftop inverter enclosures, and the AEC-Q100 grade matches the reliability requirements of long-lifetime renewable-energy equipment.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC24EP128GP204-E/TL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC24EP128GP204-E/PT | PIC24EP128GP204-E/MV | PIC24EP128GP204-I/ML | PIC24EP128GP204T-I/TL | PIC24EP128GP204-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | VTLA-44 (6x6 mm) with EP | TQFP-44 (same die, different package) | UQFN-44 (same die, different package) | QFN-44 (same die, different package) | VTLA-44 (same package, tape & reel, -I grade) | TQFP-44 (same die, different package) |
| CPU Core / Speed | PIC24E 16-bit / 70 MIPS | PIC24E 16-bit / 70 MIPS | PIC24E 16-bit / 70 MIPS | PIC24E 16-bit / 70 MIPS | PIC24E 16-bit / 70 MIPS | PIC24E 16-bit / 70 MIPS |
| Flash Program Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| Operating Temperature | -40C to +125C (E grade) | -40C to +125C (E grade) | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) |
| AEC-Q100 Qualified | Yes (automotive Grade 1) | Yes (automotive Grade 1) | Yes (automotive Grade 1) | No (industrial) | No (industrial) | No (industrial) |
| On-chip Op Amps | Up to 4 | Up to 4 | Up to 4 | Up to 4 | Up to 4 | Up to 4 |
| Operating Voltage | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V |
| Approx Unit Price (qty 1) | $5.42 | $5.20 | $5.30 | $4.75 | $4.85 | $4.55 |
Ключевые отличия
- AEC-Q100 automotive Grade 1 qualification with -40C to +125C range (против PIC24EP128GP204-I/ML)
- Compact VTLA-44 (6x6 mm) package with exposed thermal pad (против PIC24EP128GP204-E/PT (TQFP-44))
- Integrated on-chip Op Amps eliminate external conditioning (против PIC24EP128GP204-I/PT with external op amps)
- Peripheral Trigger Generator (PTG) for hardware-state-machine automation (против PIC24EP128GP204T-I/TL)
Заметки по проектированию
The VTLA-44 (TL) package has a center exposed thermal pad that MUST be soldered to a PCB pad of at least the same size, with multiple thermal vias connecting to an internal ground plane. Without proper EP soldering, thermal resistance theta_JA rises dramatically and the part will exceed maximum junction temperature under sustained CPU activity. Tie the EP to VSS for noise immunity and to provide a low-impedance thermal path. Place decoupling capacitors within 5 mm of every VDD/VSS pin pair, using a 100 nF X7R ceramic per pin plus a single 10 uF bulk capacitor near the package.
Operate only within 3.0V to 3.6V; below 3.0V the brown-out reset trips and above 3.6V the internal charge pump and Flash endurance may degrade. The PIC24E core runs at 70 MIPS but draws significantly more current at higher clock rates: estimate 60 mA typical at 70 MHz with all peripherals active. Use a linear regulator with at least 200 mA headroom (e.g., MCP1700) or a switching regulator with a low-ripple output. Apply power-up ramp rate within the datasheet specification to avoid inrush-induced brown-out events.
Pin 1 of the VTLA-44 package is identified by a small dot marking on the top surface, not by a beveled edge - inspect carefully under magnification. Configure unused pins as digital outputs driven low (not high-impedance inputs) to minimize power consumption and prevent oscillation. The Peripheral Trigger Generator (PTG) is frequently forgotten but can dramatically reduce CPU load for repetitive I/O sequencing; consult MPLAB X Code Configurator to enable it. For programming, use the PGED2/PGEC2 dedicated pair (pins 10/11) rather than remappable I/O for first-time bring-up.
Keep the analog inputs (ANx/Op Amp pins) on a separate analog ground island that joins the digital ground only at a single point under the EP. This prevents digital switching noise from coupling into the on-chip ADC and corrupting sensor readings. Route the analog traces away from high-speed digital traces (SPI, PWM outputs) and keep trace lengths under 25 mm. Place the crystal oscillator traces as short as possible, surrounded by a guard ring tied to ground, to meet the 70 MHz EMI target.
Информация о соответствии
AEC-Q100 Grade 1 automotive qualified per the -E suffix designation. Lead-free and halogen-free per Microchip product page. RoHS and REACH compliance confirmed by Microchip declaration.
