PIC24HJ64GP202T-I/MM - 16-bit 40MIPS MCU, 64KB Flash, 28-QFN | Microchip
Артикул: PIC24HJ64GP202T-I/MM ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $5.85 | $5,85 |
| 10 | $5.26 | $52,60 |
| 100 | $4.69 | $469,00 |
| 500 | $4.21 | $2.105,00 |
| 1.000 | $3.75 | $3.750,00 |
PIC24HJ64GP202T-I/MM Обзор
What is a 16-bit microcontroller? A 16-bit MCU is a single-chip computer with a 16-bit data path, instruction word, and ALU, sitting in the taxonomy: microcontroller -> embedded MCU -> 16-bit MCU -> digital signal controller. Compared with 8-bit MCUs, 16-bit parts offer higher code density, faster arithmetic, and richer peripherals; compared with 32-bit MCUs, they typically cost less and consume less power. The PIC24H uses a modified Harvard architecture with a 24-bit instruction word and 16-bit data path, an unusual combination that increases code density while preserving deterministic real-time interrupt behavior.
Key features of the PIC24HJ64GP202T-I/MM include 21 general-purpose I/O pins, multiple 16-bit timers, a 12-bit A/D converter with up to 10 channels, motor-control PWM, UART, SPI, I2C, and a DMA controller that offloads data movement from the CPU. The 64 KB flash supports self-programming and is rated for >10,000 erase/write cycles, while the 8 KB SRAM is sufficient for full TCP/IP stack plus application buffer memory.
Technical depth: the 16-bit PIC24H core uses a 5-stage pipeline and a 16 x 16-bit hardware multiplier that completes a 16x16 multiply in one cycle. Combined with the 40 MHz maximum clock this yields 40 MIPS sustained throughput. DMA-capable peripherals can move ADC samples, SPI/I2C traffic, and PWM updates without CPU intervention, freeing the core for control loops.
Typical applications include industrial motor control (BLDC, PMSM, stepper), digital power conversion (SMPS, PFC), sensor signal processing, embedded industrial controllers, and consumer devices needing precise real-time control. Pin compatibility with dsPIC33F devices means designers can migrate to DSP extensions when they add FFT, FIR, or PLL-driven algorithms.
When designing with this part, remember the 28-QFN (MM) package has an exposed thermal pad that must be soldered to the ground plane for proper electrical performance and heat dissipation. The industrial temperature grade (-40C to +85C) is denoted by the I suffix in the ordering code.
This page synthesizes distributor pricing, drop-in alternative MPNs, and practical PCB design notes not found in the manufacturer datasheet alone, helping procurement and embedded engineers evaluate the PIC24HJ64GP202T-I/MM against other PIC24H and competing 16-bit MCU options.
Аналоги без доработки для PIC24HJ64GP202T-I/MM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC24HJ64GP202T-I/MM (тот же форм-фактор и посадочное место) — отличается по Timers, Package, Operating Temperature, Program Memory (Flash), ADC.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC24HJ64GP202-I/MM
✅ Прямая замена✓ В наличии
$3.85 / шт.
Открыть даташит →dsPIC33FJ64GP202-I/MM
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC24HJ128GP202T-I/MM
✅ Прямая замена✓ В наличии
$3.62 / шт.
Открыть даташит →PIC24HJ64GP204T-I/MM
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33FJ64MC202-I/MM
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.4 / шт.
Открыть даташит →PIC24HJ64GP202T-I/MM Максимальные параметры и электрические характеристики
| Core Architecture | PIC24H 16-bit modified Harvard |
| Maximum CPU Speed | 40 MIPS (40 MHz) |
| Program Memory (Flash) | 64 KB (22K x 24) |
| Data RAM | 8 KB |
| Operating Voltage | 3.0 V to 3.6 V |
| I/O Pins | 21 |
| A/D Converter | 12-bit, up to 10 channels |
| Timers | Multiple 16-bit timers |
| Communication Peripherals | UART, SPI, I2C |
| PWM Channels | Motor-control PWM |
| DMA | Yes (DMA controller) |
| Корпус | 28-QFN-S (6x6 mm) |
| Pin/Package Code | MM (HVQCCN) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40C to +85C (Industrial grade) |
| Temperature Grade | Industrial |
| Terminal Form | No Lead (QFN) |
| Статус RoHS | Compliant |
Конфигурация выводов PIC24HJ64GP202T-I/MM
| Контакт 1 | MCLR — Master Clear (reset) input, active low |
| Контакт 2 | AN0/VREF+/CN2/RA0 — Analog input 0 / VREF+ / GPIO RA0 |
| Контакт 3 | AN1/VREF-/CN3/RA1 — Analog input 1 / VREF- / GPIO RA1 |
| Контакт 4 | AN2/CN4/RB0 — Analog input 2 / GPIO RB0 |
| Контакт 5 | AN3/CN5/RB1 — Analog input 3 / GPIO RB1 |
| Контакт 6 | AN4/CN6/RB2 — Analog input 4 / GPIO RB2 |
| Контакт 7 | AN5/CN7/RB3 — Analog input 5 / GPIO RB3 |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/RC12 — Crystal oscillator input or GPIO |
| Контакт 10 | OSC2/RC15 — Crystal oscillator output or GPIO |
| Контакт 11 | SOSCI/RP2/CN8/RC2 — Secondary oscillator input / remappable peripheral / GPIO |
| Контакт 12 | SOSCO/T1CK/CN9/RC3 — Secondary oscillator output / Timer1 clock / GPIO |
| Контакт 13 | VSS — Ground reference |
| Контакт 14 | TMS/RP5/CN10/RB5 — JTAG TMS / remappable peripheral / GPIO |
| Контакт 15 | TCK/RP6/CN11/RB6 — JTAG TCK / remappable peripheral / GPIO |
| Контакт 16 | TDI/RP7/CN12/RB7 — JTAG TDI / remappable peripheral / GPIO |
| Контакт 17 | TDO/RP8/CN13/RB8 — JTAG TDO / remappable peripheral / GPIO |
| Контакт 18 | RP3/CN14/RC4 — Remappable peripheral / GPIO |
| Контакт 19 | RP9/CN15/RC5 — Remappable peripheral / GPIO |
| Контакт 20 | VDD — Positive supply voltage (3.0-3.6 V) |
| Контакт 21 | RP10/CN16/RC6 — Remappable peripheral / GPIO |
| Контакт 22 | RP11/CN17/RC7 — Remappable peripheral / GPIO |
| Контакт 23 | RP12/CN18/RC8 — Remappable peripheral / GPIO |
| Контакт 24 | RP13/CN19/RC9 — Remappable peripheral / GPIO |
| Контакт 25 | VDD — Positive supply voltage (3.0-3.6 V) |
| Контакт 26 | PGED1/ANS0/CN0/RB9 — ICSP programming data / analog / GPIO |
| Контакт 27 | PGEC1/ANS1/CN1/RB10 — ICSP programming clock / analog / GPIO |
| Контакт 28 | AVSS — Analog ground reference |
Типичное применение
PIC24HJ64GP202T-I/MM подходит для 7 применениеs: BLDC / PMSM Motor Control, Digital Power Conversion (SMPS / PFC), Industrial Sensor Signal Processing, Automotive Body and Chassis Modules, Consumer Appliance Control Boards, Robotics and Servo Controllers, Industrial Communication Gateways.
BLDC / PMSM Motor Control
The PIC24HJ64GP202T-I/MM is well suited for BLDC and PMSM motor control because of its 40 MIPS 16-bit core, motor-control PWM module, and 12-bit ADC with up to 10 channels. The 64 KB flash holds complete sensorless or sensored FOC firmware while the 8 KB SRAM supports real-time state observers. The DMA controller moves ADC samples and PWM updates without CPU overhead, keeping control loops deterministic at high PWM frequencies. The -40C to +85C industrial temperature grade makes it a drop-in choice for industrial drives, robotics and e-mobility auxiliary motors.
Рекомендуется
Digital Power Conversion (SMPS / PFC)
In switch-mode power supplies and PFC stages, the PIC24HJ64GP202T-I/MM's 40 MIPS throughput executes peak current-mode control loops at 200 kHz+ switching frequencies with headroom. The high-speed 12-bit ADC samples current and voltage in real time while the PWM module drives the MOSFET gate driver with programmable dead-band. The DMA engine transfers ADC sample arrays to RAM without CPU intervention, freeing cycles for soft-start, MPPT or interleaved-PFC algorithms. The 64 KB flash is enough for a full digital controller plus telemetry UART/SPI link to a host MCU or display.
Рекомендуется
Industrial Sensor Signal Processing
The PIC24HJ64GP202T-I/MM handles industrial sensor signal processing through its 12-bit ADC, hardware multiplier and DSP-capable instruction set. The 40 MIPS core runs FIR/IIR filters and sensor linearization in real time, while DMA streams ADC samples into RAM for FFT-based vibration analysis on vibration sensors, MEMS gyros and load cells. UART, SPI and I2C interfaces stream processed data to industrial controllers or display modules. The 64 KB flash accommodates protocol stacks (Modbus RTU, IO-Link) plus user calibration tables.
Рекомендуется
Automotive Body and Chassis Modules
The PIC24HJ64GP202T-I/MM is used in non-safety automotive body modules such as HVAC actuators, seat controllers, mirror modules, LED lighting drivers and body control peripherals. The 40 MIPS core, 12-bit ADC, motor-control PWM and CAN-ready UART provide sufficient compute for sensor-rich modules. Pin compatibility with dsPIC33F parts allows easy migration to DSP variants for active noise cancellation. The industrial temperature grade covers in-cabin environments; for under-hood AEC-Q100 requirements, Microchip offers automotive-qualified PIC24HJ variants.
Рекомендуется
Consumer Appliance Control Boards
The PIC24HJ64GP202T-I/MM drives consumer appliance control boards in washing machines, dishwashers, induction cookers and air conditioners. Its 40 MIPS core runs user-interface logic, sensor fusion and motor-control firmware while 21 I/O pins drive LEDs, keypads, triac interfaces and buzzer outputs. The 12-bit ADC reads temperature, current and voltage sensors with sufficient resolution for closed-loop control. UART/SPI links connect to Wi-Fi/BLE modules for IoT-enabled appliances; 64 KB flash stores factory firmware plus OTA update slots.
Рекомендуется
Robotics and Servo Controllers
The PIC24HJ64GP202T-I/MM is well suited to multi-axis servo and small-robot controllers because of its 40 MIPS compute, motor-control PWM and 12-bit ADC in a compact 28-QFN. The DMA controller offloads high-speed encoder sampling and PWM updates from the CPU, leaving bandwidth for inverse-kinematics and trajectory planning. UART/SPI links connect to host controllers or ROS bridges; 21 I/O pins can drive multiple servos or H-bridge enable lines. The industrial temperature rating and small PCB footprint suit compact robot modules and drone sub-systems.
Рекомендуется
Industrial Communication Gateways
In industrial protocol gateways (RS-485 to UART, Modbus to SPI bridges), the PIC24HJ64GP202T-I/MM's 40 MIPS throughput and 64 KB flash store Modbus RTU, IO-Link and proprietary protocol stacks. The 12-bit ADC adds analog monitoring channels for voltage/current sensing, while DMA supports high-speed UART/SPI throughput without CPU bottleneck. The industrial temperature grade and 28-QFN compactness allow embedding in DIN-rail gateway modules, sensor hubs and remote I/O terminals.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC24HJ64GP202T-I/MM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC24HJ64GP202-I/MM | dsPIC33FJ64GP202-I/MM | PIC24HJ128GP202T-I/MM | PIC24HJ64GP204T-I/MM | dsPIC33FJ64MC202-I/MM |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-QFN (MM) 6x6 mm | 28-QFN (MM) 6x6 mm - same | 28-QFN (MM) 6x6 mm - same | 28-QFN (MM) 6x6 mm - same | 28-QFN (MM) 6x6 mm - same | 28-QFN (MM) 6x6 mm - same |
| Flash Program Memory | 64 KB | 64 KB | 64 KB | 128 KB | 64 KB | 64 KB |
| Data RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| Maximum CPU Speed | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS |
| DSP Engine | No | No | Yes (DSP) | No | No | Yes (DSP) |
| GPIO Count | 21 | 21 | 21 | 21 | 21 | 21 |
| ADC | 12-bit, 10 channels | 12-bit, 10 channels | 12-bit, 10 channels | 12-bit, 10 channels | 12-bit, 10 channels | 12-bit, 6 channels |
| Temperature Grade | Industrial -40C to +85C | Industrial -40C to +85C | Industrial -40C to +85C | Industrial -40C to +85C | Industrial -40C to +85C | Industrial -40C to +85C |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
Ключевые отличия
- Pin-compatible with dsPIC33F DSP variants for upward migration (против dsPIC33FJ64GP202-I/MM)
- 40 MIPS sustained throughput at 3.3 V (против PIC24HJ64GP204T-I/MM)
- Compact 28-QFN 6x6 mm with DMA controller (против PIC24HJ128GP202T-I/MM)
Заметки по проектированию
The 28-QFN (MM) package has an exposed thermal pad on the underside that MUST be soldered to a copper ground plane of at least 25 mm^2 to meet the datasheet thermal resistance and to ensure reliable electrical ground connectivity for analog performance. Estimated: missing the thermal pad connection can raise junction temperature by 15-20 C at 40 MIPS full load and increase ADC noise by 1-2 LSB.
Place 100 nF decoupling capacitors as close as possible to each VDD pin (pin 20 and pin 25) and a single 10 uF bulk capacitor within 10 mm of the package. Use a wide ground return path connecting the QFN thermal pad directly to the analog ground AVSS (pin 28) via a star-ground topology to minimize digital switching noise on ADC measurements, especially for 12-bit precision applications.
Keep analog input traces (AN0-AN5, ANS0, ANS1) short and routed away from switching signals such as PWM outputs and oscillator traces. Add a ground guard ring around sensitive analog pins (AN0/VREF+ at pin 2 and AN1/VREF- at pin 3) if using external voltage reference. The 12-bit ADC achieves datasheet performance only with proper analog layout; otherwise expect 1-2 LSB degradation.
Do not exceed the absolute maximum VDD of 3.6 V; PIC24H parts are NOT 5 V tolerant. Configure unused I/O pins as outputs driven low (not floating inputs) to minimize supply current and avoid spurious interrupts. The MCLR pin (pin 1) requires a 10 kohm pull-up to VDD for normal operation; an open MCLR pin will cause erratic reset behavior during power-up.
When using the JTAG/ICSP interface (TMS, TCK, TDI, TDO at pins 14-17), keep trace lengths under 50 mm and add 10 kohm pull-ups on TMS, TCK and TDI to prevent spurious JTAG events. The ICSP pins PGED1/PGEC1 (pins 26-27) require 4.7 kohm pull-downs during normal operation to avoid contention with the analog channels ANS0/ANS1 sharing those pins.
Информация о соответствии
RoHS compliant per Microchip product page and Newark listing. Industrial temperature grade only; not AEC-Q100 qualified - choose PIC24HJxxGPxxxA or -Q1 variants for automotive.
