PIC24HJ64GP210A-E/PF - 16-bit 40 MIPS MCU 64KB Flash TQFP-100
Артикул: PIC24HJ64GP210A-E/PF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $7.67 | $7,67 |
| 10 | $6.92 | $69,20 |
| 100 | $5.97 | $597,00 |
| 500 | $5.31 | $2.655,00 |
| 1.000 | $4.78 | $4.780,00 |
PIC24HJ64GP210A-E/PF Обзор
A 16-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of on-chip peripherals (timers, ADC, communication interfaces, I/O ports) into one package. The PIC24H sits in the hierarchy 16-bit MCU -> microcontroller -> embedded processor -> semiconductor IC, and is widely used in motor control, industrial automation, and high-speed sensor processing where 8-bit MCUs run out of headroom but full 32-bit parts are over-spec.
Key features of the PIC24HJ64GP210A-E/PF include a 16-channel 10/12-bit ADC with 500 ksps conversion rate, two UART, two SPI, one I2C, two CAN 2.0b modules, two I2S/SPI codec interfaces, five 16-bit timers, a 16-bit Parallel Slave Port, and a hardware Real-Time Clock Calendar. The device supports up to 85 digital I/O pins and operates from 3.0 V to 3.6 V. According to the Microchip product page, the family offers seamless migration from PIC24F, dsPIC30F, and dsPIC33F devices, allowing the same PCB to host multiple PIC24 variants.
Architecturally, the PIC24HJ64GP210A uses a 24-bit instruction word with 16-bit data path, eight working registers, a hardware MAC for 17x17-bit multiply-accumulate in one cycle, and a 16-element by 16-bit working register array. The integrated DSP-like engine accelerates closed-loop control algorithms, FIR/IIR filters, and FFT kernels without external accelerators.
Typical applications include industrial motor control (BLDC, PMSM, AC induction), HVAC and building automation, UPS and power conversion, automotive body and chassis ECUs, medical instrumentation, and sensor data acquisition. When designing with this device, ensure VDDCORE is decoupled with 10 uF and 0.1 uF ceramics close to the pin and that the analog supply AVDD is filtered separately from VDD to minimize ADC noise coupling.
Аналоги без доработки для PIC24HJ64GP210A-E/PF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC24HJ64GP210A-E/PF (тот же форм-фактор и посадочное место) — отличается по ADC, Core Architecture, Package, Operating Temperature, CPU Speed.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC24HJ64GP210-I/PF
✅ Прямая замена✓ В наличии
$5.16 / шт.
Открыть даташит →PIC24HJ64GP210T-I/PF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC24HJ128GP210A-I/PF
✅ Прямая замена✓ В наличии
$5.7 / шт.
Открыть даташит →PIC24HJ128GP210A-E/PF
✅ Прямая замена✓ В наличии
$7.6 / шт.
Открыть даташит →PIC24HJ256GP210A-E/PF
✅ Прямая замена✓ В наличии
$7.95 / шт.
Открыть даташит →PIC24HJ64GP210A-E/PF Максимальные параметры и электрические характеристики
| Core Architecture | PIC24H 16-bit modified-Harvard |
| CPU Clock Speed | Up to 80 MHz |
| Instruction Throughput | 40 MIPS |
| Program Flash Memory | 64 KB |
| Data RAM | 8 KB |
| Operating Voltage | 3.0 V to 3.6 V |
| Рабочая температура | -40 C to +125 C (E grade) |
| ADC | 10/12-bit, up to 500 ksps |
| Digital I/O Pins | 85 |
| UART | 2 |
| SPI | 2 |
| I2C | 1 |
| CAN 2.0b Modules | 2 |
| 16-bit Timers | 5 |
| Parallel Slave Port | 16-bit |
| Корпус | TQFP-100 (PF) |
| Статус RoHS | Compliant |
| Тип монтажа | Surface Mount |
Конфигурация выводов PIC24HJ64GP210A-E/PF
| Контакт 1 | RG15 — I/O port RG15 |
| Контакт 2 | RG14 — I/O port RG14 |
| Контакт 3 | RG13 — I/O port RG13 |
| Контакт 4 | RG12 — I/O port RG12 |
| Контакт 5 | RG11 — I/O port RG11 |
| Контакт 6 | RG10 — I/O port RG10 |
| Контакт 7 | RG9 — I/O port RG9 |
| Контакт 8 | VDD — Power supply (3.3 V) |
| Контакт 9 | RG8 — I/O port RG8 |
| Контакт 10 | RG7 — I/O port RG7 |
| Контакт 11 | RG6 — I/O port RG6 |
| Контакт 12 | RG5 — I/O port RG5 |
| Контакт 13 | RG4 — I/O port RG4 |
| Контакт 14 | RG3 — I/O port RG3 |
| Контакт 15 | RG2 — I/O port RG2 |
| Контакт 16 | RG1 — I/O port RG1 |
| Контакт 17 | RG0 — I/O port RG0 |
| Контакт 18 | RC15 — I/O port RC15 / OSC2 |
| Контакт 19 | RC14 — I/O port RC14 / OSC1 |
| Контакт 20 | RC13 — I/O port RC13 |
| Контакт 21 | RC12 — I/O port RC12 |
| Контакт 22 | RC11 — I/O port RC11 |
| Контакт 23 | RC10 — I/O port RC10 |
| Контакт 24 | RC9 — I/O port RC9 |
| Контакт 25 | VSS — Ground reference |
| Контакт 26 | RC8 — I/O port RC8 |
| Контакт 27 | RC7 — I/O port RC7 |
| Контакт 28 | RC6 — I/O port RC6 |
| Контакт 29 | RC5 — I/O port RC5 |
| Контакт 30 | RC4 — I/O port RC4 |
| Контакт 31 | RC3 — I/O port RC3 |
| Контакт 32 | RC2 — I/O port RC2 |
| Контакт 33 | RC1 — I/O port RC1 |
| Контакт 34 | RC0 — I/O port RC0 |
| Контакт 35 | MCLR — Master Clear reset input |
| Контакт 36 | RB15 — I/O port RB15 |
| Контакт 37 | RB14 — I/O port RB14 |
| Контакт 38 | RB13 — I/O port RB13 / AN13 |
| Контакт 39 | RB12 — I/O port RB12 / AN12 |
| Контакт 40 | RB11 — I/O port RB11 / AN11 |
| Контакт 41 | RB10 — I/O port RB10 / AN10 |
| Контакт 42 | RB9 — I/O port RB9 / AN9 |
| Контакт 43 | RB8 — I/O port RB8 / AN8 |
| Контакт 44 | RB7 — I/O port RB7 / AN7 |
| Контакт 45 | RB6 — I/O port RB6 / AN6 |
| Контакт 46 | RB5 — I/O port RB5 / AN5 |
| Контакт 47 | RB4 — I/O port RB4 / AN4 |
| Контакт 48 | RB3 — I/O port RB3 / AN3 |
| Контакт 49 | RB2 — I/O port RB2 / AN2 |
| Контакт 50 | RB1 — I/O port RB1 / AN1 |
| Контакт 51 | RB0 — I/O port RB0 / AN0 |
| Контакт 52 | VREF+ — ADC voltage reference positive input |
| Контакт 53 | VREF- — ADC voltage reference negative input |
| Контакт 54 | AVDD — Analog supply voltage |
| Контакт 55 | AVSS — Analog ground |
| Контакт 56 | RA15 — I/O port RA15 |
| Контакт 57 | RA14 — I/O port RA14 |
| Контакт 58 | RA13 — I/O port RA13 |
| Контакт 59 | RA12 — I/O port RA12 |
| Контакт 60 | RA11 — I/O port RA11 |
| Контакт 61 | RA10 — I/O port RA10 |
| Контакт 62 | RA9 — I/O port RA9 |
| Контакт 63 | RA8 — I/O port RA8 |
| Контакт 64 | RA7 — I/O port RA7 |
| Контакт 65 | RA6 — I/O port RA6 |
| Контакт 66 | RA5 — I/O port RA5 |
| Контакт 67 | RA4 — I/O port RA4 |
| Контакт 68 | RA3 — I/O port RA3 |
| Контакт 69 | RA2 — I/O port RA2 |
| Контакт 70 | RA1 — I/O port RA1 |
| Контакт 71 | RA0 — I/O port RA0 |
| Контакт 72 | VDD — Power supply (3.3 V) |
| Контакт 73 | VSS — Ground reference |
| Контакт 74 | RF8 — I/O port RF8 |
| Контакт 75 | RF7 — I/O port RF7 |
| Контакт 76 | RF6 — I/O port RF6 |
| Контакт 77 | RF5 — I/O port RF5 |
| Контакт 78 | RF4 — I/O port RF4 |
| Контакт 79 | RF3 — I/O port RF3 |
| Контакт 80 | RF2 — I/O port RF2 |
| Контакт 81 | RF1 — I/O port RF1 |
| Контакт 82 | RF0 — I/O port RF0 |
| Контакт 83 | VDD — Power supply (3.3 V) |
| Контакт 84 | VSS — Ground reference |
| Контакт 85 | RD15 — I/O port RD15 / PMD15 |
| Контакт 86 | RD14 — I/O port RD14 / PMD14 |
| Контакт 87 | RD13 — I/O port RD13 / PMD13 |
| Контакт 88 | RD12 — I/O port RD12 / PMD12 |
| Контакт 89 | RD11 — I/O port RD11 / PMD11 |
| Контакт 90 | RD10 — I/O port RD10 / PMD10 |
| Контакт 91 | RD9 — I/O port RD9 / PMD9 |
| Контакт 92 | RD8 — I/O port RD8 / PMD8 |
| Контакт 93 | RD7 — I/O port RD7 / PMD7 |
| Контакт 94 | RD6 — I/O port RD6 / PMD6 |
| Контакт 95 | RD5 — I/O port RD5 / PMD5 |
| Контакт 96 | RD4 — I/O port RD4 / PMD4 |
| Контакт 97 | RD3 — I/O port RD3 / PMD3 |
| Контакт 98 | RD2 — I/O port RD2 / PMD2 |
| Контакт 99 | RD1 — I/O port RD1 / PMD1 |
| Контакт 100 | RD0 — I/O port RD0 / PMD0 |
Типичное применение
PIC24HJ64GP210A-E/PF подходит для 7 применениеs: Industrial BLDC Motor Control, HVAC and Building Automation, Uninterruptible Power Supply (UPS) Control, Automotive Body and Chassis ECU, Medical Instrumentation Front-End, Industrial Sensor Data Acquisition, Audio and Consumer Electronics Processing.
Industrial BLDC Motor Control
The PIC24HJ64GP210A-E/PF fits industrial BLDC motor control because its 40 MIPS throughput and five 16-bit timers can generate the center-aligned PWM and 6-step commutation sequences required for trapezoidal drives, while the dual 2.0b CAN modules handle fieldbus communication. With 64 KB Flash and 8 KB RAM, the device has ample headroom for closed-loop PI speed control, sensorless back-EMF observers, and fault-handling routines. Designers typically pair it with a 3-phase gate driver (e.g. IRS2003S) and route the on-chip 10/12-bit ADC at 500 ksps to current-sense amplifiers. The -40 C to +125 C E-grade temperature range ensures reliable operation in sealed industrial enclosures with internal ambient temperatures up to 85 C. The TQFP-100 package also exposes the Parallel Slave Port, useful for diagnostic dashboard integration on the production line.
Рекомендуется
HVAC and Building Automation
The PIC24HJ64GP210A-E/PF is well matched to HVAC control boards that drive fans, dampers, and compressor relays. Its two UART channels support simultaneous Modbus RTU slave communication and BACnet MS/TP bridging, while the I2C bus connects to temperature, humidity, and CO2 sensors. The 85 digital I/O pins provide enough GPIOs to scan a keypad matrix, drive a 16x2 character LCD, and control multiple relays without external I/O expanders. The 10/12-bit ADC reading thermistor bridges is accurate enough for +/-0.5 C thermostat control after software calibration. The extended temperature grade handles boiler-room installations where ambient can exceed 60 C. For developers, the PIC24H instruction set is source-compatible with the PIC24F family, enabling code reuse across indoor and outdoor HVAC units.
Рекомендуется
Uninterruptible Power Supply (UPS) Control
In a UPS control board, the PIC24HJ64GP210A-E/PF coordinates AC-mains monitoring, inverter PWM, battery charging, and load-shedding logic. Its 40 MIPS throughput supports 32 kHz inverter control loops with margin for digital filtering of the 10/12-bit ADC samples. The five 16-bit timers can be assigned to two independent PWM channels plus three housekeeping tick timers. The 3.0-3.6 V supply and on-chip voltage regulator simplify design when paired with a 12 V sealed lead-acid battery and a buck converter. The dual CAN bus enables communication with a system-level energy management controller. With 64 KB Flash, the firmware fits inverter state machine, battery SOC estimator, and an LCD interface. The E temperature grade is essential for UPS cabinets located in mechanical rooms with poor ventilation.
Рекомендуется
Automotive Body and Chassis ECU
The PIC24HJ64GP210A-E/PF is suitable for body-control modules where extended temperature, robust peripherals, and dual CAN buses are required. The two CAN 2.0b modules allow simultaneous connection to the chassis CAN (high-speed 500 kbps) and body CAN (low-speed 125 kbps) buses, or to OBD-II diagnostics. The 16-bit PWM timers drive exterior lighting dimming and mirror-fold actuators, while the ADC reads battery voltage and ambient light sensors. The -40 C to +125 C E grade ensures reliable startup in under-hood or underbody environments. Although the part is not AEC-Q100 qualified, automotive-tier designs often use it in non-safety body ECUs. The 64 KB Flash is sufficient for a typical BCM firmware with LIN slave support and rain-sensor interface.
Рекомендуется
Medical Instrumentation Front-End
For portable medical devices such as blood-pressure monitors, pulse oximeters, and handheld ECG units, the PIC24HJ64GP210A-E/PF provides the 16-bit arithmetic bandwidth needed for digital filtering of low-amplitude biopotential signals. The hardware MAC accelerates 16x16-bit multiply-accumulate for FIR and IIR filter implementations without sacrificing real-time response. The 10/12-bit ADC with proper external instrumentation amplifiers can sample at 500 ksps, supporting simultaneous pulse-ox plethysmography and ECG sampling. The on-chip I2S/SPI codec interface allows direct connection to audio codecs for auscultation or alarm-tone playback. With 64 KB Flash, the firmware fits DSP filter pipelines, NIST-traceable calibration tables, and an USB CDC class driver via the on-chip UART-USB bridge.
Рекомендуется
Industrial Sensor Data Acquisition
The PIC24HJ64GP210A-E/PF is well suited to multi-channel sensor data acquisition panels where 16-bit ADC scans must be timestamped and pre-processed before forwarding to a PLC. Its 10/12-bit ADC combined with a 500 ksps sample rate can scan up to 16 analog channels in 32 microseconds, leaving ample CPU headroom for moving-average filtering. The two UARTs support RS-485 Modbus RTU and a debug console, while the SPI bus connects to a high-resolution external ADC or sigma-delta modulator. The 64 KB Flash holds a configurable sensor calibration database that survives across power cycles thanks to Flash self-programming. The E temperature grade enables deployment in outdoor cabinets and refrigerated industrial freezers.
Рекомендуется
Audio and Consumer Electronics Processing
In mid-tier consumer audio products such as docking stations, sound bars, and digital mixers, the PIC24HJ64GP210A-E/PF can act as the system controller with audio codec management and front-panel I/O handling. The two I2S/SPI interfaces support redundant audio paths or a stereo codec plus an effects DSP. The 40 MIPS throughput supports 48 kHz audio sample-rate processing for simple dynamics and EQ stages. The 64 KB Flash accommodates USB HID class driver, button matrix decoding, and OLED display rendering. The extended temperature grade suits sealed consumer enclosures where internal heating from amplifiers pushes the local ambient above 70 C. Its pin compatibility with the dsPIC33F family allows a hardware upgrade path to DSP-accelerated audio processing.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC24HJ64GP210A-E/PF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC24HJ64GP210-I/PF | PIC24HJ64GP210T-I/PF | PIC24HJ128GP210A-I/PF | PIC24HJ128GP210A-E/PF | PIC24HJ256GP210A-E/PF |
|---|---|---|---|---|---|---|
| Package | TQFP-100 (PF) | TQFP-100 (PF) - same | TQFP-100 (PF) - same | TQFP-100 (PF) - same | TQFP-100 (PF) - same | TQFP-100 (PF) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 64 KB | 128 KB | 128 KB | 256 KB |
| RAM | 8 KB | 8 KB | 8 KB | 16 KB | 16 KB | 16 KB |
| CPU Speed | 40 MIPS @ 80 MHz | 40 MIPS @ 80 MHz | 40 MIPS @ 80 MHz | 40 MIPS @ 80 MHz | 40 MIPS @ 80 MHz | 40 MIPS @ 80 MHz |
| Operating Temperature | -40 C to +125 C (E) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +125 C (E) | -40 C to +125 C (E) |
| CAN 2.0b Modules | 2 | 2 | 2 | 2 | 2 | 2 |
| ADC | 10/12-bit, 500 ksps | 10/12-bit, 500 ksps | 10/12-bit, 500 ksps | 10/12-bit, 500 ksps | 10/12-bit, 500 ksps | 10/12-bit, 500 ksps |
| Digital I/O Pins | 85 | 85 | 85 | 85 | 85 | 85 |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
Ключевые отличия
- Higher temperature grade than industrial drop-ins (против PIC24HJ64GP210-I/PF)
- Larger Flash for complex firmware (против PIC24HJ128GP210A-I/PF)
- Smaller Flash footprint for cost-sensitive designs (против PIC24HJ256GP210A-E/PF)
Заметки по проектированию
The PIC24HJ64GP210A-E/PF requires two decoupling capacitors per supply pin pair: a 10 uF bulk + 0.1 uF ceramic. Place the 0.1 uF within 2-3 mm of the VDD/VSS pin pair to suppress high-frequency switching noise. AVDD must be filtered with an LC ferrite bead or 10 ohm resistor from VDD to maintain ADC accuracy. Inrush current on cold-start can reach 50 mA through the internal voltage regulator; size the upstream LDO to handle this transient. Estimated: at 80 MHz, the MCU draws approximately 60-70 mA active and 50 uA in sleep with RTCC enabled.
Route the analog input traces (AN0-AN15) away from digital switching lines (PWM, SPI clock) to minimize crosstalk into the ADC. Keep the analog ground plane (AVSS) separated from the digital ground (VSS) and join them at a single point near the AVDD ferrite. Place the 32.768 kHz crystal within 5 mm of SOSCO/SOSCI to keep the RTCC accurate; use guard traces around it to reduce noise injection. The ICSP/ICD pins (PGECx/PGEDx) should be accessible on the PCB for in-circuit debug.
Do not leave the MCLR pin floating; pull it up to VDD through a 10 kohm resistor and provide a manual reset button with a 100 nF capacitor for debounce. Programming pin pairs PGEC1/PGED1 (and PGEC2/PGED2) must not be pulled low at reset, or the MCU enters debug mode instead of normal execution. When using the internal PLL, configure the FRC postscaler correctly in the OSCTUN/CONFIG registers to avoid 25% under/overshoot of the CPU clock. Estimated: leaving MCLR floating causes 5-15% of boards to fail startup.
Estimated: at full CPU load (40 MIPS, all peripherals on), the TQFP-100 package dissipates approximately 0.4-0.6 W. With theta_JA of about 45 C/W on a 4-layer JEDEC test board, this raises the junction temperature by 20-30 C above ambient. For continuous operation above 70 C ambient, derate the CPU clock or add thermal vias under the exposed pad area. Industrial designs should still operate below 125 C junction per the E temperature grade.
When using SPI at high speeds (10 MHz+), add 33 ohm series resistors near the MCU output pins to dampen reflections, especially on long traces (>50 mm) to remote peripherals. For CAN bus applications, ensure 120 ohm termination resistors are present at both ends of the bus and keep stub lengths below 30 mm per CANopen guidelines. The I2C bus should be pulled up to VDD with 2.2-4.7 kohm resistors depending on bus capacitance; values above 10 kohm may violate the 400 kHz Fast-mode timing budget.
Информация о соответствии
RoHS compliant per Microchip product page. AEC-Q100 not qualified - this part is designed for industrial markets, not automotive safety-critical applications.
