PIC32MX440F256HT-80V/PT - 32-bit 80MHz 256KB Flash MCU | Microchip
Артикул: PIC32MX440F256HT-80V/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.92 | $8,92 |
| 10 | $7.85 | $78,50 |
| 100 | $6.78 | $678,00 |
| 500 | $5.94 | $2.970,00 |
| 1.000 | $5.21 | $5.210,00 |
PIC32MX440F256HT-80V/PT Обзор
A PIC32 microcontroller is a 32-bit MCU based on the MIPS32 M4K core architecture, positioned above 8/16-bit families in performance and below ARM Cortex-M series in cost. The PIC32MX family integrates rich peripherals such as USB, CAN, and PMP in single-chip packages, enabling direct USB-host/device connectivity without external bridges.
Key features of the PIC32MX440F256HT-80V/PT include 256 KB Flash with 32 KB RAM, 16-bit parallel master port (PMP) for external bus interfaces, up to 5 timers, 2 I2C, 2 SPI, and 2 UART channels. The integrated full-speed USB 2.0 OTG controller with on-chip transceiver eliminates external PHY chips. With 1.56 DMIPS/MHz performance and single-cycle multiply/divide, it executes DSP-like routines efficiently for general-purpose and control applications.
The device runs from 2.3V to 3.6V with 5V-tolerant digital inputs and integrates a 10-bit 1 Msps ADC with up to 16 channels. The 80 MHz core, MIPS M4K pipeline, and 32 KB RAM allow mid-range RTOS execution or complex state-machine firmware without external SRAM.
Typical applications include USB peripherals (barcode scanners, custom HID, data loggers), industrial control PLCs, low-end HMI panels with PMP-driven LCD, embedded motor control, and consumer audio devices. The USB-OTG feature particularly fits point-of-sale terminals, USB-to-UART converters, and device-mode test instrumentation. The wide operating temperature and robust peripheral set also suit industrial automation, building automation, and medical device peripherals.
When designing with this MCU, allocate the 16 KB of boot Flash region reserved by Microchip's firmware update library. Place a 12 MHz crystal with appropriate load capacitors and provide adequate decoupling near VDD/VSS pins. Use the device's internal LDO if 5V-tolerant I/O is required.
This page synthesizes distributor pricing, drop-in PIC32MX-family alternatives, and practical design notes not found on a single datasheet page, helping engineers and buyers make informed component decisions for USB-enabled 32-bit embedded designs.
Аналоги без доработки для PIC32MX440F256HT-80V/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC32MX440F256HT-80V/PT (тот же форм-фактор и посадочное место) — отличается по Package, ADC, Core Architecture, Program Memory (Flash), SRAM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC32MX440F256H-80V/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC32MX440F256HT-80I/PT
✅ Прямая замена✓ В наличии
$6.2 / шт.
Открыть даташит →PIC32MX440F256HT-80V/MR
✅ Прямая замена✓ В наличии
$2.4 / шт.
Открыть даташит →PIC32MX450F256H-80V/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC32MX460F256L-80V/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC32MX350F256HT-V/PT
✅ Прямая замена✓ В наличии
$4.55 / шт.
Открыть даташит →PIC32MX440F256HT-80V/PT Максимальные параметры и электрические характеристики
| Core Architecture | MIPS32 M4K |
| Core Bit Width | 32-bit |
| Maximum CPU Clock | 80 MHz |
| Performance | 1.56 DMIPS/MHz |
| Flash Memory | 256 KB (256K x 8) |
| SRAM | 32 KB |
| Operating Voltage | 2.3V to 3.6V |
| Рабочая температура | -40C to +105C (Industrial) |
| ADC | 10-bit, up to 16 channels, 1 Msps |
| USB | USB 2.0 Full-Speed OTG with on-chip transceiver |
| UART | 2 |
| SPI | 2 |
| I2C | 2 |
| Parallel Master Port (PMP) | Yes (16-bit) |
| Timers | Up to 5 (16-bit) |
| Корпус | 64-TQFP (10x10 mm) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Конфигурация выводов PIC32MX440F256HT-80V/PT
| Контакт 1 | SDA1/RG3 — I2C1 SDA / Port G bit 3 |
| Контакт 2 | SCL1/RG2 — I2C1 SCL / Port G bit 2 |
| Контакт 3 | RA0 — Port A bit 0 / analog input |
| Контакт 4 | RA1 — Port A bit 1 / analog input |
| Контакт 5 | RA2 — Port A bit 2 / analog input |
| Контакт 6 | RA3 — Port A bit 3 / analog input |
| Контакт 7 | RA4 — Port A bit 4 / analog input |
| Контакт 8 | RA5 — Port A bit 5 / analog input |
| Контакт 9 | RA6 — Port A bit 6 / analog input |
| Контакт 10 | RA7 — Port A bit 7 / analog input |
| Контакт 11 | VSS — Ground reference |
| Контакт 12 | VDD — Digital supply voltage (2.3V to 3.6V) |
| Контакт 13 | RB0 — Port B bit 0 / PMP data |
| Контакт 14 | RB1 — Port B bit 1 / PMP data |
| Контакт 15 | RB2 — Port B bit 2 / PMP data |
| Контакт 16 | RB3 — Port B bit 3 / PMP data |
| Контакт 17 | RB4 — Port B bit 4 / PMP data |
| Контакт 18 | RB5 — Port B bit 5 / PMP data |
| Контакт 19 | RB6 — Port B bit 6 / PMP data |
| Контакт 20 | RB7 — Port B bit 7 / PMP data |
| Контакт 21 | RB8 — Port B bit 8 / PMP data |
| Контакт 22 | RB9 — Port B bit 9 / PMP data |
| Контакт 23 | RB10 — Port B bit 10 / PMP data |
| Контакт 24 | RB11 — Port B bit 11 / PMP data |
| Контакт 25 | RB12 — Port B bit 12 / PMP data |
| Контакт 26 | RB13 — Port B bit 13 / PMP data |
| Контакт 27 | RB14 — Port B bit 14 / PMP data |
| Контакт 28 | RB15 — Port B bit 15 / PMP data |
| Контакт 29 | VSS — Ground reference |
| Контакт 30 | VDD — Digital supply voltage (2.3V to 3.6V) |
| Контакт 31 | RC0 — Port C bit 0 |
| Контакт 32 | RC1 — Port C bit 1 |
| Контакт 33 | RC2 — Port C bit 2 |
| Контакт 34 | RC3 — Port C bit 3 |
| Контакт 35 | RC4 — Port C bit 4 |
| Контакт 36 | RC5 — Port C bit 5 |
| Контакт 37 | RC6 — Port C bit 6 |
| Контакт 38 | RC7 — Port C bit 7 |
| Контакт 39 | RC8 — Port C bit 8 |
| Контакт 40 | RC9 — Port C bit 9 |
| Контакт 41 | VDD — Digital supply voltage (2.3V to 3.6V) |
| Контакт 42 | VSS — Ground reference |
| Контакт 43 | RD0 — Port D bit 0 |
| Контакт 44 | RD1 — Port D bit 1 |
| Контакт 45 | RD2 — Port D bit 2 |
| Контакт 46 | RD3 — Port D bit 3 |
| Контакт 47 | RD4 — Port D bit 4 |
| Контакт 48 | RD5 — Port D bit 5 |
| Контакт 49 | RD6 — Port D bit 6 |
| Контакт 50 | RD7 — Port D bit 7 |
| Контакт 51 | RD8 — Port D bit 8 |
| Контакт 52 | RD9 — Port D bit 9 |
| Контакт 53 | RD10 — Port D bit 10 |
| Контакт 54 | RD11 — Port D bit 11 |
| Контакт 55 | VSS — Ground reference |
| Контакт 56 | VDD — Digital supply voltage (2.3V to 3.6V) |
| Контакт 57 | RF0 — Port F bit 0 |
| Контакт 58 | RF1 — Port F bit 1 |
| Контакт 59 | RF2 — Port F bit 2 / analog input |
| Контакт 60 | RF3 — Port F bit 3 / analog input |
| Контакт 61 | RF4 — Port F bit 4 / analog input |
| Контакт 62 | RF5 — Port F bit 5 / analog input |
| Контакт 63 | RF6 — Port F bit 6 / USB D- |
| Контакт 64 | RF7 — Port F bit 7 / USB D+ |
Типичное применение
PIC32MX440F256HT-80V/PT подходит для 7 применениеs: USB Peripherals and HID Devices, Industrial Control PLCs, Low-End HMI Panels, Embedded Motor Control, Consumer Audio Devices, Point-of-Sale Terminals, Medical Device Peripherals.
USB Peripherals and HID Devices
The PIC32MX440F256HT-80V/PT is purpose-built for USB peripherals thanks to its integrated USB 2.0 full-speed OTG controller with on-chip transceiver, eliminating external PHY cost and complexity. The 80 MHz MIPS32 M4K core runs USB stacks (Microchip Harmony, Tiny USB) at full 12 Mbps bandwidth with CPU headroom for application logic. The 256 KB Flash hosts USB stack plus custom firmware, while 32 KB SRAM handles USB endpoint buffers and HID report data. The 16-bit PMP supports external display or memory expansion for HID devices with graphical interfaces. Typical implementations include custom barcode scanners, programmable HID controllers, USB data loggers, and industrial USB-to-UART bridges.
Рекомендуется
Industrial Control PLCs
The PIC32MX440F256HT-80V/PT fits compact PLC designs by integrating 5 timers, 2 UARTs, 2 SPIs, 2 I2Cs, 16-channel 10-bit ADC, and USB on a single die. The -40C to +105C industrial-Plus temperature grade qualifies the part for factory floor environments. The 16-bit PMP can drive character LCDs or interface external I/O expanders for small-scale PLC racks. The 256 KB Flash accommodates IEC 61131-3 runtime or ladder-logic interpreters, while 32 KB RAM buffers process I/O and communication data. Industrial bus options include UART-based Modbus RTU or SPI-attached CAN controllers. This part suits sub-32-I/O PLC nodes, sensor hubs, and distributed I/O modules.
Рекомендуется
Low-End HMI Panels
The PIC32MX440F256HT-80V/PT drives compact HMI panels through its 16-bit Parallel Master Port (PMP), which interfaces directly to character or graphic LCDs and touchscreen controllers. The 80 MHz core decodes touch events, renders graphics, and runs UI state machines at refresh rates above 30 FPS. USB-OTG enables firmware update over USB and host-mode access to USB mass storage for asset-loading. The 32 KB SRAM supports frame buffers for small 320x240 LCDs, while 256 KB Flash holds the UI firmware, fonts, and asset data. The device suits appliance control panels, building automation keypads, medical device front panels, and industrial operator interfaces.
Рекомендуется
Embedded Motor Control
The PIC32MX440F256HT-80V/PT handles low-to-mid-complexity motor control applications including BLDC, stepper, and brushed DC drives. The 5 timers include PWM-capable outputs with dead-band control, while the 10-bit ADC at 1 Msps samples back-EMF and current-sense signals for FOC algorithms. The 80 MHz MIPS M4K core runs control loops at 20-50 kHz with timing headroom. USB-OTG enables tuning, firmware update, and telemetry streaming without external bridges. The industrial temperature range and 256 KB Flash accommodate sensorless FOC libraries and motor-specific tuning data, making this part suitable for small pumps, fans, and appliance motors.
Рекомендуется
Consumer Audio Devices
The PIC32MX440F256HT-80V/PT supports consumer audio devices such as USB speakers, USB headsets, and audio DAC front-ends. The integrated USB-OTG handles full-speed audio streaming (USB Audio Class 1.0 at 48 kHz/16-bit), while the 80 MHz CPU and DMA channels route audio data with minimal CPU loading. The 16-bit PMP interfaces external audio DACs, while the 10-bit ADC handles level detection and pushbutton input. The 256 KB Flash fits USB stacks plus audio processing routines, while 32 KB RAM buffers USB audio packets. The compact 64-TQFP package enables small PCB designs for portable audio peripherals.
Рекомендуется
Point-of-Sale Terminals
The PIC32MX440F256HT-80V/PT powers compact point-of-sale peripherals such as barcode readers, receipt printers, and USB-connected cash-drawer triggers. The full-speed USB-OTG supports HID keyboard emulation and CDC virtual COM port operation. The 16-bit PMP drives small graphical displays and LED status indicators, while the 32 KB SRAM buffers print data and barcode payloads. The 256 KB Flash hosts USB stacks, encryption routines, and printer command interpreters. With industrial temperature grade, this part suits retail POS peripherals in unconditioned environments.
Рекомендуется
Medical Device Peripherals
The PIC32MX440F256HT-80V/PT fits non-critical medical peripherals such as USB-connected diagnostic accessories, patient entertainment terminals, and clinical data loggers. The USB-OTG enables host-mode data transfer to USB memory sticks for clinical reports. The 10-bit ADC reads sensor inputs such as temperature or pressure for monitoring devices, and the 80 MHz core executes signal processing routines. The industrial temperature range supports hospital and clinical environments. Companion components include external signal conditioning amplifiers, isolation barriers, and medical-grade USB isolators meeting IEC 60601-1 requirements.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC32MX440F256HT-80V/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC32MX440F256H-80V/PT | PIC32MX440F256HT-80I/PT | PIC32MX440F256HT-80V/MR | PIC32MX450F256H-80V/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-QFN (8x8 mm) | 64-TQFP (10x10 mm) - same |
| Maximum CPU Clock | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| USB Module | USB 2.0 FS OTG with on-chip transceiver | USB 2.0 FS OTG with on-chip transceiver | USB 2.0 FS OTG with on-chip transceiver | USB 2.0 FS OTG with on-chip transceiver | USB 2.0 FS OTG with on-chip transceiver |
| Operating Temperature | -40C to +105C (V grade) | -40C to +105C (V grade) | -40C to +85C (I grade) | -40C to +105C (V grade) | -40C to +105C (V grade) |
| ADC | 10-bit, 16-channel, 1 Msps | 10-bit, 16-channel, 1 Msps | 10-bit, 16-channel, 1 Msps | 10-bit, 16-channel, 1 Msps | 10-bit, 16-channel, 1 Msps |
| Parallel Master Port (PMP) | Yes (16-bit) | Yes (16-bit) | Yes (16-bit) | Yes (16-bit) | Yes (16-bit) |
Ключевые отличия
- Integrated USB-OTG with on-chip transceiver eliminates external PHY (против PIC32MX340F256H-80V/PT)
- Industrial-Plus -40C to +105C temperature grade for harsh environments (против PIC32MX440F256HT-80I/PT)
- Higher-density PIC32MX4XX family with USB and PMP (против PIC32MX320F128L-80V/PT)
- 64-TQFP package with full peripheral access for hand-rework-friendly designs (против PIC32MX440F256HT-80V/MR)
Заметки по проектированию
The PIC32MX440F256HT-80V/PT operates from 2.3V to 3.6V on VDD pins, with dedicated VDDCORE pins for the internal regulator that supply the CPU core. Place a 10 uF bulk capacitor and 0.1 uF decoupling capacitors adjacent to each VDD/VSS pair, particularly near the high-current USB pins. Estimated: peak current consumption at 80 MHz with USB active is approximately 60-80 mA, requiring attention to PCB power-trace widths.
Reserve 4 KB of Flash for Microchip's bootloader library when designing firmware-upgradeable products. Configure the JTAG/TRACE pins (PGECx/PGEDx) correctly during PCB layout to avoid debugger lock-out. The 16-bit PMP requires careful PCB routing to maintain signal integrity for external LCD interfaces; keep traces under 50 mm and isolate from noisy switching nodes. Note: PIC32MX440F256HT-80V/PT differs from -80I/PT only in temperature grade; choose the correct suffix for your operating environment.
Route the USB D+/D- traces as a 90-ohm differential pair with no stubs or test points, matching the on-chip transceiver requirements per Microchip datasheet DS61143H. Keep the 12 MHz primary oscillator traces short and surround them with a ground guard ring. Place the analog AVSS/AVDD pair with its own ferrite bead to isolate ADC reference noise from digital switching. The 64-TQFP package has multiple VDD/VSS pairs; ensure each pair has its own decoupling capacitor as close to the pin as physically possible.
At 80 MHz operation with USB active and moderate GPIO toggling, the device dissipates approximately 250-400 mW. The 64-TQFP package has a thermal resistance of approximately 35-40 C/W theta_JA, allowing operation up to 105C junction without a heatsink. Estimated: at 25C ambient, junction temperature rises approximately 10-15C above ambient at full operation. For sealed enclosures, validate thermal performance with a thermocouple on the package top during worst-case duty cycle.
Информация о соответствии
RoHS compliant per Microchip product page. Not AEC-Q100 qualified (industrial-Plus grade is for industrial, not automotive). Halogen-free status not specified in available data.
