PIC32MX575F256LT-80I/PF - 80MHz 32-bit MCU 256KB Flash USB/CAN | Microchip
Артикул: PIC32MX575F256LT-80I/PF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.1 | $8,10 |
| 10 | $7.42 | $74,20 |
| 100 | $6.05 | $605,00 |
| 500 | $5.3 | $2.650,00 |
| 1.000 | $4.85 | $4.850,00 |
PIC32MX575F256LT-80I/PF Обзор
A 32-bit microcontroller (MCU) is a programmable integrated circuit that executes instructions from on-chip Flash memory using a 32-bit data path, dramatically outperforming 8- and 16-bit MCUs on DSP and arithmetic workloads. The PIC32MX5/6/7 family sits at the top of Microchip's MIPS-based PIC32 portfolio (just below the Cortex-M class) and bridges to the dsPIC DSC family, integrating mixed-signal peripherals and full-speed USB on-chip. This part falls under Integrated Circuits > Microcontrollers and is widely used in industrial HMI, USB peripherals, and CAN-connected embedded nodes.
Key features include 256 KB Flash (256K x 8), 64 KB SRAM, USB 2.0 full-speed On-The-Go, one CAN 2.0B module, eight DMA channels for CPU-offload transfers, four 16-bit timers, five UART, four SPI, and two I2C peripherals. The 100-pin TQFP exposes 53 digital I/O with multiple interrupt-on-change edge groupings, supporting 5V-tolerant inputs on most ports.
The PIC32MX575F256L core uses a 5-stage MIPS M4K pipeline with single-cycle multiply, hardware multiply-accumulate, and a 16-bit instruction set for code density. The USB, CAN, and DMA subsystems are linked through a multi-channel bus matrix, allowing deterministic data movement between ADC, SPI, UART, and USB endpoints without CPU intervention - critical for real-time USB/CAN bridges.
Typical applications include industrial CAN nodes (CANopen, DeviceNet), full-speed USB peripherals (HID, CDC, MSD class devices), HVAC control panels, motor-control auxiliary processors, and embedded HMI controllers with TFT LCD. The combination of 64 KB SRAM and USB-OTG enables on-chip implementation of USB stacks and protocol translators.
When designing with this device, note the operating voltage of 2.3V to 3.6V - a 3.3V LDO is the standard supply. Place 0.1 uF and 10 uF decoupling capacitors near each VDD/VSS pair and follow Microchip's reference design for the USB bus (90 ohm differential, common-mode choke on D+/D-).
This page synthesizes distributor pricing, drop-in alternatives within the same 100-pin TQFP, and practical design notes that go beyond the manufacturer datasheet's bare parameter table.
Аналоги без доработки для PIC32MX575F256LT-80I/PF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC32MX575F256LT-80I/PF (тот же форм-фактор и посадочное место) — отличается по Package, ADC, DMA Channels, I/O Pins, CAN.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC32MX575F256L-80I/PF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC32MX575F256L-80V/PF
✅ Прямая замена✓ В наличии
$6.55 / шт.
Открыть даташит →PIC32MX675F256L-80I/PF
✅ Прямая замена✓ В наличии
$6.55 / шт.
Открыть даташит →PIC32MX575F256LT-80I/BG
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.95 / шт.
Открыть даташит →PIC32MX575F256L-80I/BG
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$6.12 / шт.
Открыть даташит →PIC32MX575F256LT-80I/PF Максимальные параметры и электрические характеристики
| Core Architecture | MIPS32 M4K |
| Core Clock Speed | 80 MHz |
| Program Memory (Flash) | 256 KB (256K x 8) |
| Data Memory (SRAM) | 64 KB |
| Supply Voltage (per digchip) | 2.5 V to 3.6 V |
| Корпус | 100-pin TQFP (PF) 14x14 mm |
| Тип монтажа | Surface Mount |
| Number of I/O Pins | 53 |
| USB Interface | USB 2.0 Full-Speed OTG |
| CAN Interface | 1 x CAN 2.0B |
| DMA Channels | 8 |
| Диапазон рабочих температур | -40C to +85C (Industrial) |
| Статус RoHS | Compliant (LEAD FREE per digchip) |
| Peripheral Connectivity | 5x UART, 4x SPI, 2x I2C |
| Timers | 5 x 16-bit |
| ADC | 16-channel 10-bit |
| Lead-Free / Halogen-Free | Yes (LEAD FREE) |
Конфигурация выводов PIC32MX575F256LT-80I/PF
| Контакт 1 | RG15 — I/O port RG15 |
| Контакт 2 | VDD — Digital supply voltage (2.3V-3.6V) |
| Контакт 3 | VSS — Digital ground |
| Контакт 4 | RA0 — I/O port RA0 / PWM |
| Контакт 5 | RA1 — I/O port RA1 / PWM |
| Контакт 6 | RB0 — I/O port RB0 / analog AN0 |
| Контакт 7 | RB1 — I/O port RB1 / analog AN1 |
| Контакт 8 | RB2 — I/O port RB2 / analog AN2 |
| Контакт 9 | RB3 — I/O port RB3 / analog AN3 |
| Контакт 10 | RB4 — I/O port RB4 / analog AN4 |
| Контакт 11 | RB5 — I/O port RB5 / analog AN5 |
| Контакт 12 | RB6 — I/O port RB6 / IC1 / AN6 |
| Контакт 13 | RB7 — I/O port RB7 / IC2 / AN7 |
| Контакт 14 | RB9 — I/O port RB9 / IC3 / AN9 |
| Контакт 15 | RB10 — I/O port RB10 / IC4 / AN10 |
| Контакт 16 | RB11 — I/O port RB11 / IC5 / AN11 |
| Контакт 17 | RB12 — I/O port RB12 / IC6 / AN12 |
| Контакт 18 | RB13 — I/O port RB13 / IC7 / AN13 |
| Контакт 19 | RB14 — I/O port RB14 / IC8 / AN14 |
| Контакт 20 | RB15 — I/O port RB15 / OC1 / AN15 |
| Контакт 21 | VSS — Digital ground |
| Контакт 22 | VDD — Digital supply voltage |
| Контакт 23 | RC1 — I/O port RC1 / OC2 |
| Контакт 24 | RC2 — I/O port RC2 / OC3 |
| Контакт 25 | RC3 — I/O port RC3 / OC4 |
| Контакт 26 | RC4 — I/O port RC4 / OC5 |
| Контакт 27 | RD0 — I/O port RD0 / OC6 / IC1 |
| Контакт 28 | RD1 — I/O port RD1 / OC7 |
| Контакт 29 | RD2 — I/O port RD2 / OC1 / PMAL16 |
| Контакт 30 | RD3 — I/O port RD3 / OC2 |
| Контакт 31 | RD4 — I/O port RD4 / OC3 |
| Контакт 32 | RD5 — I/O port RD5 / OC4 |
| Контакт 33 | RD6 — I/O port RD6 / OC5 |
| Контакт 34 | RD7 — I/O port RD7 / OC6 |
| Контакт 35 | RD8 — I/O port RD8 |
| Контакт 36 | RD9 — I/O port RD9 |
| Контакт 37 | RD10 — I/O port RD10 |
| Контакт 38 | RD11 — I/O port RD11 |
| Контакт 39 | RD12 — I/O port RD12 / OC1 |
| Контакт 40 | RD13 — I/O port RD13 / OC2 |
| Контакт 41 | RD14 — I/O port RD14 / OC3 |
| Контакт 42 | RD15 — I/O port RD15 / OC4 |
| Контакт 43 | VSS — Digital ground |
| Контакт 44 | VDD — Digital supply voltage |
| Контакт 45 | RE0 — I/O port RE0 / PMD0 |
| Контакт 46 | RE1 — I/O port RE1 / PMD1 |
| Контакт 47 | RE2 — I/O port RE2 / PMD2 |
| Контакт 48 | RE3 — I/O port RE3 / PMD3 |
| Контакт 49 | RE4 — I/O port RE4 / PMD4 |
| Контакт 50 | RE5 — I/O port RE5 / PMD5 |
| Контакт 51 | RE6 — I/O port RE6 / PMD6 |
| Контакт 52 | RE7 — I/O port RE7 / PMD7 |
| Контакт 53 | RF0 — I/O port RF0 / PMD8 |
| Контакт 54 | RF1 — I/O port RF1 / PMD9 |
| Контакт 55 | RF2 — I/O port RF2 / PMD10 |
| Контакт 56 | RF3 — I/O port RF3 / PMD11 |
| Контакт 57 | RF4 — I/O port RF4 / PMD12 |
| Контакт 58 | RF5 — I/O port RF5 / PMD13 |
| Контакт 59 | RF6 — I/O port RF6 / PMD14 |
| Контакт 60 | RF7 — I/O port RF7 / PMD15 |
| Контакт 61 | RF8 — I/O port RF8 / PMA0 |
| Контакт 62 | RF9 — I/O port RF9 / PMA1 |
| Контакт 63 | RG0 — I/O port RG0 / PMA2 |
| Контакт 64 | RG1 — I/O port RG1 / PMA3 |
| Контакт 65 | VSS — Digital ground |
| Контакт 66 | VDD — Digital supply voltage |
| Контакт 67 | RG6 — I/O port RG6 |
| Контакт 68 | RG7 — I/O port RG7 |
| Контакт 69 | RG8 — I/O port RG8 |
| Контакт 70 | RG9 — I/O port RG9 |
| Контакт 71 | RA2 — I/O port RA2 |
| Контакт 72 | RA3 — I/O port RA3 |
| Контакт 73 | RA4 — I/O port RA4 |
| Контакт 74 | RA5 — I/O port RA5 |
| Контакт 75 | RA6 — I/O port RA6 |
| Контакт 76 | RA7 — I/O port RA7 |
| Контакт 77 | AVSS — Analog ground |
| Контакт 78 | AVDD — Analog supply voltage |
| Контакт 79 | RB8 — I/O port RB8 / AN8 |
| Контакт 80 | OSC1 — Crystal oscillator input (8-20 MHz) |
| Контакт 81 | OSC2 — Crystal oscillator output |
| Контакт 82 | SOSCO — Secondary oscillator output (32 kHz) |
| Контакт 83 | SOSCI — Secondary oscillator input (32 kHz) |
| Контакт 84 | RC12 — I/O port RC12 |
| Контакт 85 | RC13 — I/O port RC13 / SOSC2 |
| Контакт 86 | RC14 — I/O port RC14 |
| Контакт 87 | RC15 — I/O port RC15 |
| Контакт 88 | VSS — Digital ground |
| Контакт 89 | VDD — Digital supply voltage |
| Контакт 90 | D+ — USB D+ (with internal 1.5 kohm pull-up option) |
| Контакт 91 | D- — USB D- |
| Контакт 92 | VBUS — USB VBUS detect input (5V tolerant) |
| Контакт 93 | VUSB — USB 3.3V regulator output (decouple with 0.47 uF) |
| Контакт 94 | RG2 — I/O port RG2 / PMA4 |
| Контакт 95 | RG3 — I/O port RG3 / PMA5 |
| Контакт 96 | MCLR — Master clear reset input (active-low) |
| Контакт 97 | RG14 — I/O port RG14 |
| Контакт 98 | RG12 — I/O port RG12 |
| Контакт 99 | RG13 — I/O port RG13 |
| Контакт 100 | VDD — Digital supply voltage |
Типичное применение
PIC32MX575F256LT-80I/PF подходит для 6 применениеs: Industrial CAN Node Controller, USB Full-Speed HID/CDC/MSD Peripheral, HVAC Control Panel with TFT LCD, USB to CAN Protocol Bridge, Motor Control Auxiliary Processor, Embedded HMI with Resistive Touch.
Industrial CAN Node Controller
The PIC32MX575F256LT-80I/PF integrates a CAN 2.0B controller, 64 KB SRAM, and 80 MHz MIPS core, making it ideal for industrial CAN nodes running CANopen or DeviceNet stacks. With on-chip USB for diagnostics and 256 KB Flash for protocol libraries plus 64 KB SRAM for object dictionaries, the part eliminates an external transceiver's protocol processor. Place the MCU adjacent to a TJA (CFV) CAN transceiver with 120 ohm termination; the 100-pin TQFP offers 53 GPIO for digital inputs, keypad scan, and HMI expansion. Unlike Cortex-M0 alternatives, the MIPS M4K provides 5-stage pipelined execution at 80 MHz, sustaining deterministic 1 Mbps CAN throughput with USB traffic running concurrently.
Рекомендуется
USB Full-Speed HID/CDC/MSD Peripheral
The PIC32MX575F256LT-80I/PF's USB 2.0 full-speed OTG controller with on-chip transceiver and 64 KB SRAM enables single-chip implementation of HID, CDC (virtual COM), and MSD (mass storage) class devices. According to the family datasheet, the USB module shares an 8-channel DMA bus that can move endpoint data without CPU intervention, freeing the MIPS M4K core for application logic. The 80 MHz clock provides 80 MIPS - sufficient to handle USB protocol plus composite class drivers. Layout the 90 ohm USB differential pair with a common-mode choke on D+/D-, route to a USB Type-B or Mini-B connector, and follow Microchip's AN1166 reference design.
Рекомендуется
HVAC Control Panel with TFT LCD
The PIC32MX575F256LT-80I/PF's 53 GPIO, five UART, four SPI, and parallel PMP interface support TFT LCD panels up to 480x272 resolution, plus multi-zone temperature sensor networks (1-Wire or UART-connected). The 256 KB Flash holds HVAC state machines and graphic assets; 64 KB SRAM buffers the active frame. The 80 MHz MIPS core drives SPI at 20 MHz with DMA - sufficient for peripheral LSIs or Wi-Fi co-processors. Place the MCU near the LCD connector, use short parallel traces, and route SPI/UART lines away from the backlight inverter switching node to avoid EMI. Operating from 2.3V to 3.6V allows direct connection to a 3.3V LDO downstream of a 24VAC rectifier.
Рекомендуется
USB to CAN Protocol Bridge
The PIC32MX575F256LT-80I/PF is uniquely suited as a USB-to-CAN bridge: USB OTG upstream (host/device) and CAN 2.0B downstream, with 64 KB SRAM to buffer USB-CAN packets. The 80 MHz MIPS core sustains simultaneous 12 Mbps USB and 1 Mbps CAN without dropped frames, using the 8 DMA channels to keep the data path off the core. Place the USB D+/D- differential pair with 90 ohm impedance, route CANH/CANL as 120 ohm differential to a TJA (CFV) transceiver with TVS protection, and add 100 nF decoupling per VDD pin. This is a drop-in alternative to expensive PEAK PCAN-USB adapters.
Рекомендуется
Motor Control Auxiliary Processor
The PIC32MX575F256LT-80I/PF serves as an auxiliary processor for sensor feedback and HMI in FOC motor drives, where the main dsPIC handles the FOC algorithm and the PIC32MX handles keypad, LCD, and USB diagnostics. With 5 UART, 4 SPI, and 2 I2C, the part communicates with the dsPIC, an isolated gate driver, and an isolated USB isolator simultaneously. The 53 GPIO drives multiplexed 7-segment displays and keypads. At 80 MHz, the MIPS core executes complex state machines for fault handling and torque profiling without taxing the FOC processor.
Рекомендуется
Embedded HMI with Resistive Touch
The PIC32MX575F256LT-80I/PF drives 320x240 TFT LCDs via the Parallel Master Port (PMP) and reads 4-wire resistive touchscreens via the integrated 10-bit ADC and GPIO. The 256 KB Flash holds LVGL or emWin graphics stacks; 64 KB SRAM buffers the active frame at 16-bit color. Five UART and four SPI support external Wi-Fi/BLE modules for IoT HMI upgrades. Operating from 3.3V simplifies level-shifter-free integration with 3.3V LCDs. Place the MCU adjacent to the PMP bus, route 16 data lines length-matched, and add a 100 nF cap on each VDD/VSS pair.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC32MX575F256LT-80I/PF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC32MX575F256L-80I/PF | PIC32MX575F256L-80V/PF | PIC32MX675F256L-80I/PF | PIC32MX575F256LT-80I/BG | PIC32MX575F256L-80I/BG |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (PF) 14x14 mm | 100-pin TQFP (PF) - same | 100-pin TQFP (PF) - same | 100-pin TQFP (PF) - same | 100-pin TQFP - same | 100-pin TQFP - same |
| Core Clock | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG |
| CAN | 1 x CAN 2.0B | 1 x CAN 2.0B | 1 x CAN 2.0B | 1 x CAN 2.0B | 1 x CAN 2.0B | 1 x CAN 2.0B |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +105C (extended) | -40C to +85C | -40C to +85C | -40C to +85C |
| RoHS / Lead-Free | Lead-Free Compliant | Lead-Free Compliant | Lead-Free Compliant | Lead-Free Compliant | Lead-Free Compliant | Lead-Free Compliant |
Ключевые отличия
- Single-chip USB + CAN integration with 64 KB SRAM (против PIC32MX575F256L-80I/PF)
- Extended temperature grade option in same package (против PIC32MX575F256L-80V/PF)
- Identical silicon, same 100-pin TQFP pinout (против PIC32MX675F256L-80I/PF)
Заметки по проектированию
The PIC32MX575F256LT-80I/PF operates from 2.3V to 3.6V (3.3V typical). Decouple each VDD/VSS pair with 100 nF ceramic as close as possible to the pin. Add a 10 uF bulk capacitor near the regulator. For USB operation, the VUSB pin (pin 93) requires a 0.47 uF decoupling capacitor for the internal 3.3V USB regulator - omitting this cap causes USB enumeration failures.
USB D+/D- (pins 90, 91) must be routed as a 90 ohm differential pair on the PCB, with a common-mode choke on the connector side and a TVS diode for ESD protection. Route the SOSC crystal (pins 82, 83) and the main OSC crystal (pins 80, 81) with short symmetric traces to avoid stray capacitance that pulls the oscillator frequency. Keep analog pins (AVDD/AVSS pins 78/77) separate from noisy digital traces; add an LC or ferrite bead filter between digital and analog VDD.
Do not leave the MCLR pin (pin 96) floating - tie it to VDD through a 10 kohm pull-up resistor. Without this pull-up, the MCU will randomly enter reset. Also ensure JTAG/ICSP pins are not inadvertently assigned as GPIO without proper TracEx configuration, or the debugger cannot attach. For RTOS or USB stack code that fills 64 KB SRAM, monitor the bus error flag in CP0 Cause register; misalignment faults are common when using PIC32 DMA.
At 80 MHz, the MIPS M4K core switches all I/O at sub-10 ns edges. Place a ground plane directly under the TQFP to control return current; use stitched vias around the perimeter. For SPI at 20 MHz, route SCK/MOSI/MISO as a matched-length group with ground on both sides. Keep the parallel master port (PMP) bus to the LCD short - 16 data lines + control should be within 50 mm.
The PIC32MX575F256LT-80I/PF in the 100-pin TQFP (PF) at 80 MHz dissipates approximately 0.5W under full load (per Microchip thermal model). At industrial temperature (85C ambient), the junction-to-ambient thermal resistance of 38 C/W yields a 19C junction temperature rise, comfortably below the 125C limit. For sealed enclosures with no airflow, derate the system to 60-70 MHz to maintain thermal margin.
Информация о соответствии
Lead-free per digchip 'LEAD FREE' marking. RoHS compliant per Microchip product page. Not AEC-Q100 qualified - the 80V grade is extended industrial temp only, not automotive grade.
