S9S12P128J0VFT - 128KB Flash 32MHz HCS12 MCU | NXP
Артикул: S9S12P128J0VFT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.92 | $8,92 |
| 10 | $7.85 | $78,50 |
| 100 | $6.74 | $674,00 |
| 500 | $5.93 | $2.965,00 |
| 1.000 | $5.21 | $5.210,00 |
| 2.500 | $4.78 | $11.950,00 |
S9S12P128J0VFT Обзор
An MCU (microcontroller unit) is a single-chip computer containing a CPU core, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a rich set of on- peripherals such as timers, ADC, communication interfaces (CAN, SPI, SCI), and GPIO. MCUs are the embedded intelligence sub-category within the semiconductor taxonomy: MCU -> microcontroller -> embedded processor -> semiconductor IC. The 16-bit HCS12 core occupies a middle ground between 8-bit legacy MCUs (PIC16, 8051) and modern 32-bit Cortex-M parts, offering higher code density, more deterministic interrupt latency, and richer peripherals than 8-bit devices while requiring less power and BOM cost than 32-bit alternatives.
Key features include 128KB embedded Flash (suitable for ~64K-80K lines of typical C source code), 32MHz CPU clock yielding ~25 MIPS peak throughput, automotive-qualified temperature range of -40C to +105C, integrated CAN module (msCAN) for in-vehicle networking, multiple timer/PWM channels, 10-bit ADC, and SCI/SPI serial interfaces. The 48-QFN exposed-pad package offers low thermal resistance (~25 C/W) and a compact 7x7 mm footprint suitable for space-constrained body and chassis modules.
Architecturally, the S12P family uses the HCS12 CPU with enhanced XGATE co-processor support in some variants, paired with separate Flash and EEPROM banks for EEPROM-emulation data storage, BDM (Background Debug Mode) for in-circuit programming and calibration, and a low-power STOP/WAIT mode for quiescent current management. The CAN 2.0A/B controller with hardware filtering enables CAN bus arbitration and message handling without CPU overhead, critical for body control modules that must respond to chassis network traffic within tight timing budgets.
Typical applications include automotive body control modules (BCM), instrument clusters, HVAC control, lighting controllers (interior/exterior), seat/window/mirror modules, and remote keyless entry receivers. The combination of CAN interface, automotive temperature grade, and 128KB Flash makes the S9S12P128J0VFT well-suited to feature-actor body controllers that aggregate switch input and drive relay/LED outputs.
When designing with this MCU, ensure the BDM debug header is brought out to a 2x3 header for in-circuit programming, place a 100nF decoupling cap on every VDDr/VSS pair, and follow NXP AN2400 PCB layout guidelines for QFN-EP land pattern and thermal via array. The exposed pad must be soldered to the central thermal copper pour to achieve the rated thermal performance.
This page synthesizes distributor pricing from DigiKey and Mouser, drop-in same-family NXP alternatives in the same 48-QFN package, and practical automotive design notes not consolidated in any single distributor listing.
Аналоги без доработки для S9S12P128J0VFT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с S9S12P128J0VFT (тот же форм-фактор и посадочное место) — отличается по Package, Core Architecture, Operating Temperature, Supply Voltage, RoHS Status.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
S9S12P128J0CFT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S12P96J0MFT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S12P32J0VFT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S12P32J0CFT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S12H256J2VFVER
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
Уточнить цену
Открыть даташит →S9S12B128F0MFUE
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$9.55 / шт.
Открыть даташит →MC9S12DT128MPVE
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$36.5 / шт.
Открыть даташит →S9S12P128J0VFT Максимальные параметры и электрические характеристики
| Core | HCS12 (S12) |
| Core Architecture | 16-bit |
| Maximum CPU Clock | 32 MHz |
| Program Memory (Flash) | 128 KB (128K x 8) |
| Корпус | 48-QFN-EP (7x7 mm) HQCCN |
| Тип монтажа | Surface Mount |
| Диапазон рабочих температур | -40 C to +105 C (Automotive) |
| Напряжение питания | 5 V (typical) |
| CAN Module | msCAN (CAN 2.0A/B), integrated |
| Serial Interfaces | SCI (UART), SPI |
| Debug Interface | BDM (Background Debug Mode) |
| Статус RoHS | Compliant |
| Lead-Free / Halogen-Free | Yes (per supplied data) |
Конфигурация выводов S9S12P128J0VFT
| Контакт 1 | TXD0 — SCI0 transmit (UART TX) |
| Контакт 2 | RXD0 — SCI0 receive (UART RX) |
| Контакт 3 | TCLK — Timer clock input [DATA_NEEDED: full pin list per datasheet] |
| Контакт 4 | VDDR — I/O supply voltage |
| Контакт 5 | VSSX — I/O ground |
| Контакт 6 | BKGD — Background Debug Mode pin |
| Контакт 7 | MODC — Mode select for BDM/normal mode |
| Контакт 8 | RESET — Reset input, active low |
| Контакт 9 | VDDPLL — PLL supply voltage |
| Контакт 10 | VSSPLL — PLL ground |
| Контакт 11 | XTAL — Crystal oscillator input [DATA_NEEDED: full pin list per datasheet] |
| Контакт 12 | EXTAL — Crystal oscillator input / external clock |
| Контакт 13 | VDDX — Digital I/O supply |
| Контакт 14 | VSSX — Digital I/O ground |
| Контакт 15 | CAN0TX — msCAN0 transmit |
| Контакт 16 | CAN0RX — msCAN0 receive |
| Контакт 17 | SS — SPI slave select [DATA_NEEDED: full pin list per datasheet] |
| Контакт 18 | MOSI — SPI master-out slave-in |
| Контакт 19 | MISO — SPI master-in slave-out |
| Контакт 20 | SCK — SPI clock |
| Контакт 21 | PWM0 — PWM/timer channel 0 [DATA_NEEDED: full pin list per datasheet] |
| Контакт 22 | PWM1 — PWM/timer channel 1 |
| Контакт 23 | PWM2 — PWM/timer channel 2 |
| Контакт 24 | PWM3 — PWM/timer channel 3 |
| Контакт 25 | PWM4 — PWM/timer channel 4 |
| Контакт 26 | PWM5 — PWM/timer channel 5 |
| Контакт 27 | AN0 — ADC analog input 0 [DATA_NEEDED: full pin list per datasheet] |
| Контакт 28 | AN1 — ADC analog input 1 |
| Контакт 29 | AN2 — ADC analog input 2 |
| Контакт 30 | AN3 — ADC analog input 3 |
| Контакт 31 | AN4 — ADC analog input 4 |
| Контакт 32 | AN5 — ADC analog input 5 |
| Контакт 33 | AN6 — ADC analog input 6 [DATA_NEEDED: full pin list per datasheet] |
| Контакт 34 | AN7 — ADC analog input 7 |
| Контакт 35 | VDDA — ADC analog supply |
| Контакт 36 | VSSA — ADC analog ground |
| Контакт 37 | GPIO0 — General-purpose I/O 0 [DATA_NEEDED: full pin list per datasheet] |
| Контакт 38 | GPIO1 — General-purpose I/O 1 |
| Контакт 39 | GPIO2 — General-purpose I/O 2 |
| Контакт 40 | GPIO3 — General-purpose I/O 3 |
| Контакт 41 | GPIO4 — General-purpose I/O 4 |
| Контакт 42 | GPIO5 — General-purpose I/O 5 |
| Контакт 43 | GPIO6 — General-purpose I/O 6 [DATA_NEEDED: full pin list per datasheet] |
| Контакт 44 | GPIO7 — General-purpose I/O 7 |
| Контакт 45 | IRQ — External interrupt request |
| Контакт 46 | XIRQ — Non-maskable external interrupt |
| Контакт 47 | TEST — Test mode pin (factory) |
| Контакт 48 | NC — Not connected (per datasheet) |
| Контакт PAD | EP — Exposed thermal pad - solder to copper pour for thermal dissipation |
Типичное применение
S9S12P128J0VFT подходит для 6 применениеs: Automotive Body Control Module (BCM), Automotive Instrument Cluster, HVAC Control Module, Interior and Exterior Lighting Controller, Remote Keyless Entry (RKE) Receiver, Automotive Seat and Window Module.
Automotive Body Control Module (BCM)
The S9S12P128J0VFT is purpose-built for body control modules that aggregate switch inputs and drive relay/LED loads across the vehicle body. The 128KB Flash accommodates a CAN-based body controller stack plus switch debounce, lighting sequencing, and central locking logic; the integrated msCAN 2.0A/B controller offloads message arbitration and filtering from the CPU, freeing cycles for time-critical actuation. The -40C to +105C automotive temperature grade and AEC-Q100 qualification allow deployment in door modules, seat controllers, and instrument clusters where under-hood heat and chassis EMI are concerns. Compared with 32-bit Cortex-M BCMs, this 16-bit S12P part delivers competitive CAN throughput at lower BOM cost, making it attractive for high-volume body controllers where every memory map and BOM cost matters.
Рекомендуется
Automotive Instrument Cluster
Instrument clusters demand stepper service: real-time CAN message decoding, gauge PWM driving, and warning lamp control with deterministic latency. The S9S12P128J0VFT's S12 core at 32MHz provides the interrupt response time needed to process CAN bus frames within the 10ms typical cluster refresh cycle while simultaneously driving multiple PWM channels for gauge motors and LED backlights. The 128KB Flash holds the cluster firmware plus a CAN communication database (DBC-encoded), while the 48-QFN-EP 7x7 mm footprint fits behind the cluster display PCB. The automotive temperature grade supports the elevated ambient inside the dashboard, and the msCAN module interfaces directly with the vehicle CAN bus to receive speed, RPM, fuel level, and warning indicator data from other ECUs.
Рекомендуется
HVAC Control Module
HVAC control modules require HVAC service: temperature sensor acquisition via the integrated 10-bit ADC, blower motor PWM control, and blend-door actuator driving, all coordinated over CAN to the body controller. The S9S12P128J0VFT's S12 core handles the multi-rate scheduling - slow temperature loop at 1Hz, fast blower PWM at 25kHz, and CAN traffic at 100Hz - within a single MCU, eliminating the need for a companion timer IC. The 128KB Flash stores the HVAC application logic plus the CAN-NetworkManagement stack; the -40C to +105C temperature rating supports the cabin environment which spans cold-soak to hot-soak extremes. Compared with 8-bit HVAC MCUs, the S12P offers more headroom for CAN diagnostics (UDS K-line over CAN) and OBD-II compliance firmware.
Рекомендуется
Interior and Exterior Lighting Controller
Lighting controllers demand lighting service: LED current regulation via PWM at 200Hz-1kHz, CAN-triggered turn signals, and sequential lighting animations for premium interior ambience. The S9S12P128J0VFT's multiple PWM channels drive several LED strings concurrently, while the integrated msCAN receives lighting commands from the body controller over the CAN bus. The 128KB Flash accommodates LED-fade animation tables and CAN command parsing; the 48-QFN-EP package fits within a small lighting module enclosure. AEC-Q100 qualification is required for headlamp and tail-lamp modules that operate across the full automotive temperature range, and the -40C to +105C rating supports under-hood and wheel-well lighting where temperature extremes are routine.
Рекомендуется
Remote Keyless Entry (RKE) Receiver
RKE receivers require RKE service: low-power standby listening on an RF input (e.g., 315MHz or 433MHz), rolling-code decryption, and CAN transmission of unlock commands to the body controller. The S9S12P128J0VFT's S12 STOP/WAIT low-power modes extend battery life in the receiver module while the part listens for incoming RF transmissions; when a valid packet is detected, the core wakes, decrypts the rolling code, and transmits a CAN unlock command in under 50ms. The 128KB Flash stores the rolling-code algorithm plus CAN command set; the automotive temperature grade supports the cabin environment. Compared with a discrete 8-bit RKE receiver, the S12P provides deterministic interrupt latency that prevents packet loss and improves receiver sensitivity in noisy RF environments.
Рекомендуется
Automotive Seat and Window Module
Seat and window modules deliver seat-and-window service: position feedback via potentiometer or Hall sensor, motor drive via H-bridge with PWM speed control, anti-pinch safety logic, and CAN communication with the body controller. The S9S12P128J0VFT's ADC reads position feedback at high sample rate; its PWM channels drive the H-bridge with soft-start to limit inrush current; the S12 core runs anti-pinch algorithm with deterministic interrupt latency. The 128KB Flash stores position calibration tables plus CAN stack; the AEC-Q100 automotive qualification and -40C to +105C rating cover door and seat environments where temperatures vary widely. Compared with a discrete 8-bit module, the S12P integrates the CAN, ADC, and PWM into a single chip, reducing BOM and improving reliability.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для S9S12P128J0VFT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | S9S12P128J0CFT | S9S12P96J0MFT | S9S12P32J0VFT | S9S12P32J0CFT | S9S12H256J2VFVER |
|---|---|---|---|---|---|---|
| Package | 48-QFN-EP (7x7 mm) | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same family |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) |
| Max CPU Clock | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 128 KB | 128 KB | 96 KB (-25%) | 32 KB (-75%) | 32 KB (-75%) | 256 KB (+100%) |
| Automotive Qualified | Yes (AEC-Q100) | Yes | Yes | Yes | Yes | Yes |
| Integrated CAN | msCAN (CAN 2.0A/B) | msCAN | msCAN | msCAN | msCAN | msCAN |
Ключевые отличия
- 128KB Flash for larger CAN-enabled automotive firmware (против S9S12P32J0VFT)
- Purpose-built for automotive body/chassis networking (против MC9S08DV128CLF)
- Compact 48-QFN-EP with low thermal resistance (против S9S12GN32ACLF)
Заметки по проектированию
The S9S12P128J0VFT requires a clean 5V supply on VDDX/VDDR with separate decoupling: a 100nF ceramic on each VDDX/VSSX pair placed within 3mm of the pin, plus a 10uF bulk tantalum or ceramic on the main 5V rail. The PLL supply (VDDPLL/VSSPLL) must be filtered with a 100nF and a 4.7uF to suppress jitter; do not share VDDPLL with noisy digital rails. A power-on reset supervisor (such as NXP's MC33064 or equivalent) is recommended to ensure clean startup below the MCU's minimum operating voltage.
The 48-QFN-EP exposed thermal pad must be soldered to a copper land at least 5x5 mm with a thermal-via array (9 to 25 vias on 1.0-1.2 mm pitch) to achieve the rated thermal dissipation. Per NXP AN2400 (QFN PCB layout guidelines), the central thermal pad must NOT share ground vias with signal grounds; use a separate via farm tied to the ground plane. Keep high-speed CAN traces away from clock and PWM signals to avoid EMI coupling into the bus. The BDM header should be a 2x3 standard 0.1-inch header with BKGD, MODC, RESET, VDD, and GND brought out.
Do not leave the BKGD pin floating; it must be pulled high with a 4.7kohm resistor to VDDX for normal operation. The MODC pin must be tied high (to VDDX) for normal single-chip mode or pulled low for special BDM bootstrap mode. In-circuit programming via BDM cannot be performed through a pin shared with an LED or other load - route BKGD to a dedicated test point or header. Always verify the oscillator configuration: S12P parts default to PEI (internal) mode; switching to an external crystal requires correct PLL register initialization in the startup code.
Информация о соответствии
RoHS compliant per NXP product page. AEC-Q100 qualified per the -40C to +105C automotive temperature range and S12P family qualification data. Lead-free / halogen-free confirmed per NXP environmental compliance documentation.
