SN75112D - Dual 2/0 Line Driver | Texas Instruments
Артикул: SN75112D ✓ АктивенSN75112D Обзор
A line driver is a digital interface IC that converts a low-voltage logic signal into a stronger output signal suitable for driving a transmission line or connected load. In the broader semiconductor hierarchy, the SN75112D belongs to the interface IC family, where transmitters and drivers condition logic signals for reliable communication between circuit blocks. The SN75112D implements this function as two channels in a single package, allowing one component to service two independent data paths.
The device's principal technical feature is its regulated output-current behavior. According to the Texas Instruments product page, the SN75112's higher current of 27 mA permits data transmission over longer lines than lower-current family members. Two channels support economical point-to-point interfaces, while independent operation reduces the need for separate single-channel driver packages. Its 10 V TTL-input compatibility broadens its usefulness in mixed legacy and modern logic environments.
Internally, the SN75112D is optimized for constant-current output behavior rather than simple rail-to-rail switching. The manufacturer highlights improved stability over supply-voltage and temperature ranges, high output impedance, and an extended common-mode output-voltage range. These features are particularly relevant when the connected line presents variable loading, long interconnect distances, or noise-prone industrial environments. Exact propagation-delay, supply-voltage, and absolute-maximum limits should be confirmed in the manufacturer datasheet before final circuit release.
Typical uses include industrial data links, control interfaces, test equipment, and communications equipment where a transmitter must drive a terminated or capacitively loaded cable. Texas Instruments specifically notes optimum performance with the SN55107A, SN75107A, and SN75108A line receivers. The dual-channel organization also makes the device appropriate for paired control and data paths, provided the receiver and transmitter voltage levels remain compatible.
For implementation, verify the supported supply voltage, input logic thresholds, timing limits, and output load capability against the manufacturer datasheet. Place the device close enough to the driven line interface to limit additional trace loading, maintain a continuous return path, and observe the required bypass-capacitor arrangement. Input and output ringing should be evaluated with the actual cable, termination, connector, and receiving-device loading.
This product page consolidates the verified manufacturer identity, package information, interface characteristics, related receiver options, and engineering selection criteria. It also separates a true dual line driver from broader transceiver categories and identifies the two same-family line-driver alternatives that can be evaluated for legacy-interface designs.
Аналоги без доработки для SN75112D — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
SN55110A
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
SN75110A
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
SN75112D Характеристики
| Product Type | Dual line driver, 2 channels |
| Driver Configuration | 2/0 driver |
| Количество выводов | 14 pins |
| Корпус | 14-pin SOIC (D) |
| Output Current | 27 mA |
| Channel Independence | 2 independent channels |
| Output-Current Regulation | Improved across supply-voltage and temperature variations |
| Output Stability | Improved over supply-voltage and temperature ranges |
| TTL Input Compatibility | 10 V compatible |
| Тип монтажа | Surface mount |
Руководство по цоколевке SN75112D в корпусе 14-pin soic (d)
Цоколевка для SN75112D (корпус 14-pin soic (d)). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для SN75112D.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
SN75112D подходит для 6 применениеs: Industrial Control Data Links, Point-to-Point Communications Equipment, Test and Measurement Systems, TTL-Compatible Legacy Interfaces, Instrument and Control Panels, Security and Surveillance Equipment.
Industrial Control Data Links
The SN75112D fits bidirectional-system interfaces that need a dedicated transmitter for each control or status path. Its two independent channels reduce component count, while the stated 27 mA output-current capability is suited to longer driven lines than lower-current drivers. The improved output-current regulation across supply-voltage and temperature variations also helps maintain consistent drive behavior. In an industrial controller, place each output close to its connector or cable driver and confirm receiver thresholds, common-mode limits, grounding, and surge protection against the actual cable environment.
Рекомендуется
Point-to-Point Communications Equipment
The SN75112D is useful in point-to-point communications equipment that transmits two independent digital signals over cable or board-level interconnects. Its dual 2/0 organization lets one package drive two channels, while 27 mA output-current capability supports the longer transmission distances identified by the manufacturer. The high output impedance and high common-mode output-voltage range help describe its behavior on variable loads. The receiving device should be selected from the manufacturer-recommended SN55107A, SN75107A, or SN75108A family and validated with the physical cable and termination.
Рекомендуется
Test and Measurement Systems
The SN75112D can drive control, trigger, or status lines in a test and measurement system where the destination may be farther from the logic circuitry than a direct digital output can accommodate. Two independent channels simplify paired control paths, and the 27 mA output-current capability provides additional drive margin over lower-current family members. Because the driver is not an isolation barrier, cable transients still require suitable protection. Confirm timing, supply range, and output loading in the manufacturer datasheet, then verify signal integrity at the receiver with the intended cable and probe load.
Рекомендуется
TTL-Compatible Legacy Interfaces
The SN75112D is appropriate for legacy control interfaces requiring 10 V TTL-input compatibility. Its two channels can carry independent data or control signals, while the improved output-current regulation helps maintain behavior across supply-voltage and temperature changes. In a mixed-generation system, verify that the receiver recognizes the driver's actual output levels and that the logic source meets the SN75112D input thresholds. Confirm that the selected system supply is inside the device operating range and use the manufacturer datasheet to establish timing margins before connecting long or noisy lines.
Рекомендуется
Instrument and Control Panels
The SN75112D can drive signal lines from an instrument or control panel toward a remote receiver where cable capacitance and loading create a more demanding transmission path. Dual independent outputs reduce the space required for two single-channel drivers, and the stated 27 mA capability supports longer-line operation identified by the manufacturer. High output impedance can be useful when the interface requires controlled drive behavior, but the complete load and termination arrangement still determines the usable bandwidth. Validate eye timing and ringing at the receiver using the final wiring harness.
Рекомендуется
Security and Surveillance Equipment
The SN75112D can provide separate drive channels for alarm, control, or status links in surveillance equipment installed away from the main controller. The dual-channel format simplifies board area, while its improved current regulation and 27 mA output-current capability help preserve signal behavior across supply and temperature variations. Long outdoor cables remain vulnerable to surges and induced noise, so the driver should not be treated as a surge protector. Use appropriate line protection, maintain a controlled reference ground, and verify the receiver thresholds and common-mode operating conditions at both ends.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для SN75112D — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SN55110A | SN75110A |
|---|---|---|---|
| Package | 14-pin SOIC (D) | 14-pin SOIC | 14-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Dual line driver | Dual line driver | Dual line driver |
| Channel Count | 2 independent channels | 2 channels | 2 channels |
| Output-Current Regulation | Improved over supply-voltage and temperature variations | Improved over supply-voltage and temperature variations | Improved over supply-voltage and temperature variations |
Ключевые отличия
- Higher stated output-current capability within the manufacturer family (против SN75110A)
- Two independently operating driver channels in one package (против SN55110A)
- Manufacturer-identified optimum receiver-family support (против SN75110A)
Заметки по проектированию
Evaluate the completed interface with the actual cable, connector, receiver, and termination. The SN75112D's stated 27 mA output-current capability and improved current regulation help support longer lines, but they do not determine edge rate or acceptable loading by themselves. Confirm propagation timing and rise/fall behavior in the manufacturer datasheet, then inspect the receiver end for ringing, threshold-margin loss, and reflections under the worst-case supply and temperature conditions.
Route each driver output toward its connector or cable interface with a short, continuous return path, and keep the device close enough to the driven line to minimize additional trace capacitance and susceptibility to coupled noise. Because the device has two independent channels, maintain consistent routing geometry between them where timing relationship matters. Confirm the complete pin assignments and bypass requirements from the manufacturer datasheet before finalizing the 14-pin SOIC footprint.
Do not assume that every SN75110-family device is interchangeable merely because it is a dual line driver. The SN75112D is specifically identified as the higher-current family member with 27 mA output-current capability. Before substituting SN55110A or SN75110A, compare output current, supply range, propagation delay, enable behavior, and every numbered pin. If any function or timing value differs, redesign or qualify the substitute rather than relying on the common 14-pin SOIC outline.
Long line connections can pick up external noise and reflect driver edges. Use the manufacturer-recommended SN55107A, SN75107A, or SN75108A receivers, select the proper termination arrangement for the physical cable, and compare received waveforms at the far end. Add suitable surge and ESD protection where exposed to industrial or outdoor environments; the line driver itself is not an isolation or surge-protection device.
Информация о соответствии
The manufacturer and distributor information does not state the required compliance statuses for this exact ordering option. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status on the current manufacturer product documentation before qualification.