SP3232EUCN-L/TR - 1 Mbps 3.3V RS-232 | MaxLinear
Артикул: SP3232EUCN-L/TR ✓ АктивенSP3232EUCN-L/TR Обзор
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. Within the interface hierarchy, it is a serial transceiver, a line-driver and line-receiver component, and ultimately a semiconductor designed for data communication and industrial-control equipment.
The SP3232E has two transmit channels and two receive channels, allowing two serial links or bidirectional operation on one device. Its 1000 kbps signaling rate supports relatively high-speed RS-232 communication compared with slower legacy transceivers. Operation from a single 3.3 V supply also simplifies power design in portable systems, while the charge-pump topology generates the bipolar voltage required by RS-232 without a separate negative supply.
MaxLinear describes the SP3232E series as a solution for portable or hand-held computers, including notebook and palmtop platforms. The same architecture is useful for instrument control, point-of-sale equipment, industrial serial adapters, and embedded systems that exchange data with a host over RS-232.
The charge-pump network requires small 0.1 µF capacitors for 3.3 V operation. Place these capacitors close to their associated pins and keep the RS-232 driver and receiver traces away from sensitive analog or high-speed digital paths. Confirm the exact pin names and exposed functions against the MaxLinear datasheet before assigning PCB nets.
This product page combines the SP3232E family electrical characteristics, package information, drop-in replacement guidance, comparison data, and practical PCB design notes to support faster component selection and implementation.
Аналоги без доработки для SP3232EUCN-L/TR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с SP3232EUCN-L/TR (тот же форм-фактор и посадочное место) — отличается по Package, Maximum Data Rate, Operating Temperature, Mounting Type, Operating Supply Voltage.
SP3232EEY-L/TR
✅ Прямая заменаУточнить цену
Открыть даташит →SP3232EEN-L/TR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →SP3232ECY-L/TR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →SP3232ECA-L/TR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →SP3232EUCN-L/TR Характеристики
| Product Type | RS-232 transceiver IC |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Interface Standard | RS-232 |
| Maximum Data Rate | 1000 kbps |
| Supply Voltage at 3.3 V Operation | 3.3 V |
| Power-Supply Architecture | Single supply with integrated charge pump |
| Charge-Pump Capacitor Requirement | 0.1 µF in 3.3 V operation |
| Корпус | 16-pin SOIC |
| Тип монтажа | Surface mount |
| Commercial Operating Temperature Range | 0 °C to 70 °C |
| AEC-Q100 Qualification | not_applicable |
Руководство по цоколевке SP3232EUCN-L/TR в корпусе 16-pin soic
Цоколевка для SP3232EUCN-L/TR (корпус 16-pin soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для SP3232EUCN-L/TR.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
SP3232EUCN-L/TR подходит для 6 применениеs: Portable Computer Serial Interface, Industrial Serial Adapter, Point-of-Sale Terminal, Test and Measurement Equipment, Embedded Controller Communication, Data Acquisition and Control Module.
Portable Computer Serial Interface
The SP3232EUCN-L/TR fits a portable computer or data-acquisition accessory that requires an RS-232 port from a 3.3 V system. Its two drivers and two receivers support two serial channels, while the 1000 kbps capability accommodates faster UART links than many legacy transceivers. The integrated charge pump avoids a separate negative supply and needs only 0.1 µF capacitors in the documented 3.3 V configuration. Place the charge-pump capacitors near the IC and route the cable-side traces away from sensitive processor and memory signals.
Рекомендуется
Industrial Serial Adapter
The SP3232EUCN-L/TR is suitable for a compact industrial adapter that converts a 3.3 V UART into RS-232. Two driver and two receiver channels allow connection to more than one downstream serial device, and the 1000 kbps maximum rate supports higher-throughput command and telemetry links. The single-supply charge-pump architecture reduces external power complexity, while its 16-pin SOIC package simplifies assembly. Confirm grounding, cable shielding, and ESD requirements at the enclosure and connector interface.
Рекомендуется
Point-of-Sale Terminal
The SP3232EUCN-L/TR can provide the physical RS-232 layer in a point-of-sale terminal or peripheral controller powered from 3.3 V. Two receive channels can accommodate two peripheral links, while two driver channels provide outbound command or data paths. Its 1000 kbps rate exceeds typical legacy peripheral baud rates and gives the design additional timing margin. Use the exact UART baud rate, parity, and cable length as part of the system timing budget, and verify signal polarity against the selected connector wiring.
Рекомендуется
Test and Measurement Equipment
The SP3232EUCN-L/TR is appropriate for a compact instrument that exposes an RS-232 control or service port. The 1000 kbps signaling rate supports fast command exchange, and the dual-channel arrangement can simplify sharing between instrument subsystems. Its 3.3 V operation and low-capacitance charge-pump requirement help preserve board area in portable test equipment. Separate the RS-232 cable interface from sensitive analog measurement circuits, and validate ground-offset behavior in the final equipment configuration.
Рекомендуется
Embedded Controller Communication
The SP3232EUCN-L/TR allows an embedded controller with a 3.3 V UART to communicate with an RS-232 modem, reader, or service unit. The 2-driver, 2-receiver arrangement supports simultaneous signal paths and multidrop-style cable wiring where the system design permits it. A maximum rate of 1000 kbps allows a higher baud-rate link than common 230 kbps RS-232 transceivers. Match the UART settings and logic levels to the transceiver specification, and use the manufacturer pin-description table to assign every package terminal.
Рекомендуется
Data Acquisition and Control Module
The SP3232EUCN-L/TR is suitable for a data-acquisition module that accepts commands or returns records through RS-232. The 1000 kbps maximum rate can shorten transfer time for larger data packets, while the 3.3 V supply and 16-pin SOIC package support compact controller boards. Two driver and receiver channels offer flexibility for separate control and monitoring paths. For long cables or noisy industrial environments, validate signal integrity with the actual cable, baud rate, and grounding arrangement rather than relying only on nominal device ratings.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для SP3232EUCN-L/TR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SP3232EEY-L/TR | SP3232EEN-L/TR | SP3232ECY-L/TR | SP3232ECA-L/TR |
|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | MaxLinear, Inc. | MaxLinear, Inc. | MaxLinear, Inc. | MaxLinear, Inc. | MaxLinear, Inc. |
| Product Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 |
| Maximum Data Rate | 1000 kbps | 1000 kbps | 1000 kbps | 1000 kbps | 1000 kbps |
| 3.3 V Operation | Supported | Supported | Supported | Supported | Supported |
| Charge-Pump Capacitor | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF |
| Special Features | Integrated charge pump with 2 drivers and 2 receivers | Same SP3232E family architecture | Same SP3232E family architecture | Same SP3232E family architecture | Same SP3232E family architecture |
Ключевые отличия
- Higher nominal RS-232 speed than lower-rate alternatives (против ST3232ECDR)
- Single 3.3 V supply with integrated charge-pump support (против ST3232ECDR)
- Four communication channels in one interface IC (против SP232EET-L/TR)
Заметки по проектированию
Place the documented 0.1 µF charge-pump capacitors directly beside the corresponding SP3232E pins and keep their ground returns short. The MaxLinear application circuit is the preferred starting point because capacitor placement affects the charge-pump loop and radiated noise. Avoid routing RS-232 driver outputs beneath sensitive analog or high-speed digital traces, and provide a solid ground reference between the transceiver and connector.
Separate the cable-side RS-232 nets from UART logic and internal power signals. Maintain a practical ground connection at the interface boundary, but follow the system grounding strategy so that cable surge currents do not flow through sensitive circuit ground paths. If the board includes both a transceiver and a connector, place the ESD-protection component close to the connector and the transceiver close to its supply and charge-pump components.
Do not assume that every SP3232E ordering suffix is an unconditional drop-in alternative. Verify the package body dimensions, lead pitch, pin assignment, temperature range, and exposed terminal treatment before releasing a PCB substitution. Also confirm the UART baud rate against the 1000 kbps transceiver limit, since protocol overhead and system latency reduce the usable application throughput.
Информация о соответствии
The manufacturer material identifies the SP3232E as a commercial portable-equipment interface product. RoHS, REACH, lead-free, halogen-free, and conflict-mineral status require confirmation from the current manufacturer product or material declaration.