STM8L101K3U6 - 16MHz 8KB Low-Power MCU | STMicroelectronics
Артикул: STM8L101K3U6 ✓ АктивенSTM8L101K3U6 Обзор
An ultra-low-power microcontroller is a semiconductor controller designed to balance processing capability with minimized energy consumption. The STM8L family combines a compact CISC architecture, low-power operating modes, and integrated peripherals for battery-operated, compact, and low-duty-cycle products. It belongs to the hierarchy of microcontrollers, embedded processors, integrated circuits, and semiconductors.
The STM8L101K3U6 provides up to 16 MIPS at 16 MHz according to the STMicroelectronics STM8L101x3 product page. Its 8 KB Flash configuration supports compact control code in applications that do not require a large memory footprint. The 32-UFQFPN package offers a small 5 mm by 5 mm surface-mount solution, while the exposed-pad construction supports heat transfer from the device to the PCB.
The STM8L101K3 belongs to the STM8L101x1, STM8L101x2, and STM8L101x3 low-power family. The enhanced STM8 CPU core provides increased processing performance while retaining CISC code density, 24-bit linear addressing, and an architecture optimized for low-power operation. The manufacturer identifies operation from 1.65 V to 3.6 V and an industrial temperature range of -40°C to +85°C for the closely related STM8L101K3U6TR ordering code.
Typical uses include compact sensor controllers, battery-powered instruments, low-power monitoring nodes, appliance controls, and embedded products in which a small MCU package and energy-conscious operation are important. The device is also suitable for simple communication, timing, analog-monitoring, and actuator-control functions when firmware and peripheral requirements fit the 8 KB Flash configuration.
Designers should confirm the exact peripheral map, pin functions, clock requirements, and exposed-pad connection in the manufacturer datasheet before layout release. The 5 V by 5 mm footprint requires careful thermal-via placement under the exposed pad, while the low 1.65 V minimum operating voltage constrains compatible sensors, transceivers, and external interface circuits.
This product overview combines the manufacturer family information, exact MPN specifications, package characteristics, application guidance, and a focused drop-in comparison to support faster MCU selection and board-layout review.
Аналоги без доработки для STM8L101K3U6 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с STM8L101K3U6 (тот же форм-фактор и посадочное место) — отличается по Flash Memory, CPU Architecture, LCD Support, Product Family, Series.
STM8L101G3U6A
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM8L152K6U6
✅ Прямая заменаУточнить цену
Открыть даташит →STM8L151K6U6
✅ Прямая заменаУточнить цену
Открыть даташит →STM8L101K2U6
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
STM8L101K1U6
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
STM8L101K3U6 Максимальные параметры и электрические характеристики
| Product Type | 8-bit ultra-low-power microcontroller |
| Product Family | STM8L EnergyLite |
| Maximum CPU Frequency | 16 MHz |
| Maximum Performance | 16 MIPS at 16 MHz |
| Flash Memory | 8 KB (8K x 8) |
| CPU Architecture | Enhanced STM8 CISC core |
| Addressing Space | 24-bit linear |
| Operating Voltage | 1.65 V to 3.6 V |
| Рабочая температура | -40°C to +85°C |
| Корпус | 32-pin UFQFPN (5 mm x 5 mm) |
| Тип монтажа | Surface mount |
| Thermal Construction | Exposed pad |
Руководство по цоколевке STM8L101K3U6 в корпусе 32-pin ufqfpn (5 mm x 5 mm)
Цоколевка для STM8L101K3U6 (корпус 32-pin ufqfpn (5 mm x 5 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для STM8L101K3U6.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
STM8L101K3U6 подходит для 6 применениеs: Battery-Powered Sensor Node, Industrial Environmental Monitoring, Low-Power Data Acquisition, Smart Appliance Control, Wearable Health Device, Compact Communication Controller.
Battery-Powered Sensor Node
The STM8L101K3U6 fits compact battery-powered sensor nodes because its enhanced STM8 core operates up to 16 MHz while retaining an architecture optimized for low-power work, and the device runs from 1.65 V to 3.6 V. It can periodically wake, acquire data, perform local control, and return to a low-energy state without requiring a larger application processor. The 8 KB Flash capacity suits small protocol stacks and tightly bounded sensor logic, while the 5 mm by 5 mm 32-pin UFQFPN package preserves board area. Design the power tree around the lowest usable rail, minimize always-on peripherals, and measure average current with the intended sensor and radio load.
Рекомендуется
Industrial Environmental Monitoring
The STM8L101K3U6 is appropriate for compact environmental-monitoring modules that sample sensors, apply filtering, enforce thresholds, and report readings through a serial interface. Its 16 MHz maximum clock provides useful processing headroom for a 3.6 V system, while the -40°C to +85°C range supports industrial-temperature designs. The 8 KB Flash limit makes disciplined firmware sizing important when adding protocol handling or local data storage. Place the MCU close to the sensor interface to minimize trace susceptibility to noise, use a dedicated regulator path for analog sensing if required, and verify that every timer and communication peripheral used by the module is present in the exact STM8L101K3 variant.
Рекомендуется
Low-Power Data Acquisition
The STM8L101K3U6 can serve as the acquisition controller in a low-power instrument that converts sensor inputs into a compact digital record. Its enhanced STM8 CPU can deliver up to 16 MIPS at 16 MHz, enabling local filtering, calibration, and status processing without a high-power processor. Operating from 1.65 V to 3.6 V supports low-energy system rails, and the exposed-pad UFQFPN construction can improve heat transfer when copper and thermal vias are provided. For accurate measurements, separate analog and digital return paths, keep sensitive inputs away from switching nodes, and confirm the available ADC characteristics in the manufacturer electrical data before selecting gain and sampling rates.
Рекомендуется
Smart Appliance Control
The STM8L101K3U6 is suitable for smart-appliance subcontrollers that coordinate buttons, relays, indicators, and simple sensors while consuming little standby power. Its 16 MHz STM8 core handles timing and state management, and its 8 KB Flash is most effective when the firmware is organized around direct peripheral control rather than a large embedded operating system. The 32-pin 5 mm by 5 mm package supports compact control boards, although inductive or high-current loads should use separate driver stages. Provide local protection for exposed connector pins, keep switching devices away from sensitive control traces, and verify that each relay or motor driver interface has suitable voltage, current, and isolation margins.
Рекомендуется
Wearable Health Device
The STM8L101K3U6 can support a wearable health device in which a small low-power MCU handles sensor acquisition, button input, vibration control, and short burst communications. Its 1.65 V to 3.6 V operating range suits compact energy-storage systems, while the 16 MHz maximum operating frequency permits responsive control without a complex processor core. The 5 mm by 5 mm package helps minimize board area, but battery-current demand will be dominated by sensors and wireless circuitry. Use low-power modes between measurements, disable unused clock trees and peripherals, and validate the complete system's average current rather than estimating battery life from the MCU specification alone.
Рекомендуется
Compact Communication Controller
The STM8L101K3U6 can act as a compact protocol controller for a small sensor, actuator, or service interface where the required code fits within 8 KB Flash. Its enhanced 8-bit STM8 core supports CISC-oriented firmware with 24-bit linear addressing, while operation up to 16 MHz provides adequate control performance for many serial protocols and simple packet handling. The device should be selected only after checking the exact available UART, SPI, I2C, timer, and interrupt resources. Match the MCU and transceiver to the same voltage domain, provide adequate bus pull-ups, route communications away from switching power nodes, and confirm protocol timing under the system's worst-case clock configuration.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для STM8L101K3U6 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | STM8L101G3U6A | STM8L152K6U6 | STM8L151K6U6 | STM8L101K2U6 | STM8L101K1U6 |
|---|---|---|---|---|---|---|
| Package | 32-UFQFPN (5 mm x 5 mm) | 32-UFQFPN (5 mm x 5 mm) | 32-UFQFPN (5 mm x 5 mm) | 32-UFQFPN (5 mm x 5 mm) | 32-UFQFPN (5 mm x 5 mm) | 32-UFQFPN (5 mm x 5 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Maximum CPU Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 8 KB | 8 KB | 32 KB | 16 KB | 4 KB | 2 KB |
Ключевые отличия
- Balances 16 MHz processing with compact code-memory requirements (против STM8L101K2U6)
- More code space for low-power firmware than the lower-density family options (против STM8L101K1U6)
- Smaller memory footprint than the higher-capacity STM8L alternatives (против STM8L152K6U6)
- Lower memory configuration than the STM8L151 option (против STM8L151K6U6)
Заметки по проектированию
The 32-UFQFPN package uses an exposed thermal pad, so the PCB stack-up and copper area directly affect operating temperature. Place a compact array of thermal vias beneath the pad and connect them to a low-impedance ground plane where the manufacturer pinout permits. Apply even solder coverage to the exposed pad to avoid voids, and avoid placing thermally sensitive analog components immediately beneath the MCU. Validate the assembled board at the maximum expected ambient temperature and load.
Route sensitive sensor and analog signals away from the MCU clock pins, exposed-pad vias, and any nearby switching circuitry. Keep the 32-pin footprint's perimeter pads and exposed pad within the manufacturer's land-pattern tolerances, and follow the assembly land-pattern drawing rather than a generic QFN footprint. Because the exact pin map is not listed on the product page, cross-check every net against the datasheet pin-description table before releasing artwork or ordering assembly fixtures.
Design the supply network for the documented 1.65 V to 3.6 V operating range and place the local bypass capacitors directly beside the appropriate power and ground pins. Keep the power loop short, use a quiet return path, and isolate analog or radio loads from the MCU rail when they create large transients. Confirm startup behavior across the full input range, especially when attached sensors begin in an active state before the MCU controls their power.
Do not treat a matching UFQFPN package as proof of a drop-in replacement. Firmware, clock initialization, interrupt vectors, peripheral assignments, and alternate-pin functions can differ even among devices from the same STM8 family. For any listed alternative, compare every used pin, the maximum clock setting, supply limits, oscillator requirements, and all active peripherals. Run a proof-of-concept build and peripheral-level test before authorizing a production substitution.
Информация о соответствии
The manufacturer product page does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for this exact ordering code. AEC-Q100 is not applicable to the standard industrial-temperature STM8L101K3U6 ordering code.
