Texas Instruments

TAS5186DDVR - 6-Channel 210W Class D Power Stage | TI (Tape & Reel)

Артикул: TAS5186DDVR ✓ Активен
13.2 V Vdss 44-terminal HTSSOP Package
MOQ: 1 |

TAS5186DDVR Обзор

The Texas Instruments TAS5186DDVR is a six-channel Class D digital-amplifier power stage rated for 210 W total output power, with 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% power-stage efficiency at 1 W into the recommended single-ended loads. The device is housed in a 44-terminal HTSSOP package and operates from a 10.8 V to 13.2 V supply.

A Class D power stage is an audio-amplifier output circuit that switches its supply rails at high frequency to produce a filtered audio waveform. It belongs to the amplifier IC hierarchy, where a digital-input power stage removes the need for external analog audio-input circuitry when it is paired with a compatible audio codec or digital-audio processor. Its principal advantages are high conversion efficiency, compact implementation, and integration of speaker-output protection.

The TAS5186DDVR provides six independent amplification channels for multichannel audio systems. Its published performance includes 105 dB A-weighted signal-to-noise ratio, THD+N below 0.05% at 1 W, and efficiency above 90% into recommended loads. Integrated protection covers undervoltage, overtemperature, overload, and short-circuit conditions, reducing the amount of discrete protection required around each speaker output.

Digital inputs allow the amplifier to receive audio samples directly from an audio codec, DSP, or other digital-audio source. This architecture supports a compact signal chain and accurate channel synchronization. The 44-terminal HTSSOP package also provides a practical surface-mount footprint for multi-channel consumer and professional audio equipment, subject to careful thermal and layout design.

Typical uses include powered speakers, soundbar amplifier boards, home-theater receiver power stages, active subwoofer systems, and compact multimedia speaker designs. Its six-channel architecture is particularly useful when one board must drive multiple surround-sound channels without implementing six separate discrete amplifier circuits.

Designers should follow the manufacturer layout guidance for high-current speaker and power-ground paths, place the required decoupling capacitors close to the device, and verify copper area for thermal dissipation. Thermal performance depends on output power, channel utilization, load impedance, PCB copper, and ambient temperature, so a compact enclosure should be validated under worst-case multichannel conditions.

This page combines the device's principal performance specifications, application guidance, design cautions, and identified pin-compatible family options for faster engineering selection. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning PCB nets and confirming thermal limits.

Аналоги без доработки для TAS5186DDVR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с TAS5186DDVR (тот же форм-фактор и посадочное место).

TAS5186ADDVR

✅ Прямая замена
📦 44-HTSSOP
Same six-channel, 60 W-class digital power-stage family, but the TAS5186A provides an improved protection system

📋 Справочный аналог (нет в каталоге)

TAS5186DDVRG4

✅ Прямая замена
📦 44-HTSSOP
Same six-channel 60 W-class architecture and HTSSOP footprint; G4 ordering designation differs without a stated electrical difference

📋 Справочный аналог (нет в каталоге)

TAS5186DDVG4

✅ Прямая замена
📦 44-HTSSOP
Same six-channel 60 W-class architecture and HTSSOP footprint; G4 ordering designation differs without a stated electrical difference

📋 Справочный аналог (нет в каталоге)

TAS5176DDWR

✅ Прямая замена
Texas Instruments
📦 44-HTSSOP
Six-channel digital-amplifier power stage · 6 channels · 100 W · Class D · PWM input · 0 V to 34 V · 10.8 V to 13.2 V · 5.1-channel

Уточнить цену

Открыть даташит →

TAS5186DDVR Максимальные параметры и электрические характеристики

Amplifier Type 6-channel Class D digital-amplifier power stage
Total Output Power 210 W
Rated Power per Channel 30 W per channel at 5 channels
Maximum Supply Voltage 13.2 V
Minimum Supply Voltage 10.8 V
Signal-to-Noise Ratio 105 dB A-weighted
Total Harmonic Distortion plus Noise <0.05% at 1 W
Power-Stage Efficiency >90% at 1 W into recommended single-ended loads
Выходная конфигурация 6 channels, single-ended
Input Interface Digital audio input
Integrated Protection Undervoltage, overtemperature, overload, and short-circuit protection
Корпус 44-terminal HTSSOP
Тип монтажа Surface mount
Terminal Count 44 terminals
Temperature Grade Commercial

Руководство по цоколевке TAS5186DDVR в корпусе 44-terminal htssop

Цоколевка для TAS5186DDVR (корпус 44-terminal htssop). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса 44-terminal htssop для TAS5186DDVR

Нет подробных данных о распиновке для TAS5186DDVR.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

TAS5186DDVR подходит для 6 применениеs: Powered Bookshelf Speakers, Home-Theater Amplifier Board, Soundbar Speaker Amplification, Active Subwoofer Power Stage, Digital Audio Speaker System, Portable Multimedia Speaker.

🎧

Powered Bookshelf Speakers

The TAS5186DDVR fits a powered bookshelf speaker requiring multiple amplified channels and digital audio input. Its six-channel architecture can support left, right, center, surround, and additional drivers without six separate output devices, while the 210 W total rating provides useful channel-power headroom. The 105 dB A-weighted SNR helps preserve low-level detail in quiet passages, and THD+N below 0.05% at 1 W supports clean mid-volume operation. A compact enclosure requires careful PCB copper and thermal validation because sustained multichannel load raises dissipation.

📺

Home-Theater Amplifier Board

The TAS5186DDVR is appropriate for a home-theater power stage that must drive multiple surround-sound channels. Six integrated Class D outputs reduce the board area required by discrete amplifier solutions, while digital inputs support a codec-to-amplifier signal path. The device's 10.8 V to 13.2 V supply range suits a nominal 12 V architecture, but rail tolerance and transient headroom must be included in system design. Its 105 dB A-weighted SNR is useful for cinema playback, and integrated overload, short-circuit, undervoltage, and thermal protection provide baseline speaker-rail safeguards.

🔊

Soundbar Speaker Amplification

A soundbar amplifier board benefits from the TAS5186DDVR's six-channel output in a single 44-terminal HTSSOP package. The digital input architecture shortens the analog path between an audio processor and the Class D outputs, and the device can drive several drivers used by left, right, center, surround, or bass functions. Its 210 W total rating provides flexibility for channel allocation, while greater than 90% efficiency at 1 W reduces power loss in the output stage. Soundbar enclosure cooling remains critical, particularly when several channels operate simultaneously at substantial output power.

🔉

Active Subwoofer Power Stage

The TAS5186DDVR can form part of an active subwoofer or multi-driver bass amplification system using one or more of its six Class D channels. Its 60 W-class channel capability is relevant for compact speaker designs, while the 210 W total device rating allows flexible use of several channels. The 105 dB A-weighted SNR supports low background noise, and integrated short-circuit and overload protection are valuable around speaker wiring. Because bass transducers can demand sustained high current, the PCB must use short, wide output paths and adequate copper area, and thermal performance must be tested at the lowest intended speaker impedance.

🖥️

Digital Audio Speaker System

The TAS5186DDVR is well suited to a fully digital speaker system in which an audio codec or DSP delivers digital samples directly to the Class D power stage. This architecture avoids carrying high-level analog audio across much of the board and supports controlled channel synchronization. Six outputs can serve multiple drivers, while the 10.8 V to 13.2 V operating range allows use in a nominal 12 V system. The designer must match digital-interface timing and filtering to the source, validate the full data path for dropout behavior, and follow the manufacturer grounding and output-filter recommendations.

📱

Portable Multimedia Speaker

The TAS5186DDVR can support portable multimedia equipment when its 10.8 V to 13.2 V supply requirement is compatible with the system battery and converter design. The six-channel output reduces the number of separate amplifier packages required for compact speakers, and Class D efficiency helps limit conversion loss. Its digital input interface can simplify connection to a portable media processor, while 105 dB A-weighted SNR preserves quiet-playback performance. A portable enclosure limits copper area and passive cooling, making thermal simulation and sustained-load testing essential rather than relying only on the 210 W aggregate rating.

What is the TAS5186DDVR?
The TAS5186DDVR is a Texas Instruments six-channel Class D digital-amplifier power stage rated for 210 W total output power. According to the manufacturer datasheet, it provides 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% efficiency at 1 W into recommended single-ended loads. It is packaged in a 44-terminal HTSSOP and accepts digital audio inputs, making it suitable for compact powered-speaker and multichannel home-audio systems.
What are the key specifications of TAS5186DDVR that engineers should know?
The TAS5186DDVR combines six digital-input Class D output channels with 210 W total rated output power in a 44-terminal HTSSOP. Its headline specifications are 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, greater than 90% efficiency at 1 W, and a 10.8 V to 13.2 V supply range. According to the manufacturer datasheet, integrated protection includes undervoltage, overtemperature, overload, and short-circuit functions.
What is the operating voltage of TAS5186DDVR?
The TAS5186DDVR operates from 10.8 V to 13.2 V. The manufacturer datasheet identifies this range as the device supply requirement, making the amplifier suitable for nominal 12 V power systems when the complete board maintains adequate ripple, tolerance, and transient headroom. The supply limits should be checked against the system rail, startup sequence, and protection behavior before deployment.
How much power can TAS5186DDVR deliver?
The TAS5186DDVR is rated for 210 W total output power, with the manufacturer datasheet also listing 5 × 30 W performance. This represents a multichannel operating configuration rather than a guarantee that every channel continuously produces 210 W. Actual output depends on channel count, load impedance, supply voltage, THD+N limit, PCB thermal design, and ambient temperature, all of which should be validated in the finished enclosure.
What is the audio performance of TAS5186DDVR?
The TAS5186DDVR delivers 105 dB A-weighted SNR and less than 0.05% THD+N at an output power of 1 W, according to the manufacturer datasheet. These figures make the device suitable for high-fidelity powered speakers, soundbars, and home-theater amplification where low idle noise and low small-signal distortion are important. Evaluate the complete signal chain and configured output filters as well, because system-level distortion also depends on the digital source and analog output stage.
What is the pinout of TAS5186DDVR?
The TAS5186DDVR uses a 44-terminal HTSSOP package, but a terminal-by-terminal public pin map is not reproduced on this page. Use the pin-description table and package drawing in the manufacturer datasheet before assigning power, ground, digital-audio, control, and speaker-output nets. Do not infer HTSSOP pin functions from another 44-terminal amplifier because reserved and test terminals can differ between devices.
Where can I download the TAS5186DDVR datasheet PDF?
The TAS5186DDVR manufacturer datasheet is available through the Texas Instruments product document links. The document describes the six-channel digital-amplifier power stage, recommended application circuit, electrical characteristics, protection behavior, pin descriptions, and package information. Use the PDF for final schematic, layout, thermal, and component-selection decisions rather than relying on distributor summaries or catalog listings.
What is the best drop-in replacement for TAS5186DDVR?
TAS5186ADDVR is the closest identified family alternative because it retains the six-channel Class D architecture, 60 W-class output capability, and HTSSOP form factor while introducing an improved protection system. It should not be installed without checking pin assignments, control logic, supply sequencing, and thermal conditions in the manufacturer datasheet. No verified cross-brand, pin-to-pin replacement was identified, so a second-source substitution requires manufacturer-level compatibility confirmation.
Can TAS5186ADDVR replace TAS5186DDVR?
TAS5186ADDVR can be considered for a drop-in design review because it is an enhanced six-channel digital-amplifier power stage in the same HTSSOP family. Its improved protection system is the principal documented difference. Before replacement, compare every pin, digital-input format, control signal, power-supply limit, and speaker-output connection in the two manufacturer datasheets, and verify that the revised protection behavior meets the product requirements.
TAS5186DDVR vs TAS5176DDWR: which is better for multichannel audio?
The TAS5186DDVR is the stronger choice for a multichannel design requiring higher output power: comparison data identifies it as a 60 W Class D amplifier versus 40 W for TAS5176DDWR. Both use a 44-pin HTSSOP package, but the 20 W rating difference is substantial. Use TAS5176DDWR only when its lower channel power satisfies the speaker loads and budget; verify pin-level compatibility rather than treating package similarity alone as sufficient.
TAS5186DDVR vs TAS5186ADDVR: which should I choose?
Choose TAS5186ADDVR when the improved protection system is valuable and its manufacturer documentation confirms compatibility with the intended board. Choose TAS5186DDVR when the original device already satisfies the design and no redesign is desired. Both provide a six-channel digital-amplifier power stage with approximately 60 W-class output, but TAS5186ADDVR is described as having improved protection, making the choice a functional protection review rather than simply a speed or capacity comparison.
When should I choose TAS5186DDVR over TAS5176DDWR?
Choose TAS5186DDVR over TAS5176DDWR when channel power headroom is the deciding requirement. The identified ratings are approximately 60 W for TAS5186DDVR and 40 W for TAS5176DDWR, a 20 W or 50% increase in the stated class of output. Both occupy a 44-pin HTSSOP footprint, which can simplify mechanical planning, but the designer must still confirm pin compatibility, digital timing, protection behavior, and thermal requirements.
Is TAS5186DDVR suitable for powered speakers and home theater?
The TAS5186DDVR is suitable for powered speakers, soundbars, and home-theater amplification because it combines six Class D channels with digital inputs and 210 W total rated power. Its 105 dB A-weighted SNR supports high-fidelity use, while integrated undervoltage, overtemperature, overload, and short-circuit protection improves system robustness. Suitability depends on speaker impedance, channel loading, enclosure cooling, and the digital-audio source.
Where can I buy TAS5186DDVR and check its lead time?
Use the Request a Quote form on this page to request TAS5186DDVR pricing, current availability, lead time, and order quantity for your project. The inquiry should include the required quantity, shipping destination, and whether the part must be supplied in a specific package or tube-and-reel configuration. This approach provides current commercial terms without embedding prices that may change independently of the component.
Is TAS5186DDVR in stock and what is the current lead time?
Current stock and lead time for TAS5186DDVR should be confirmed through the Request a Quote form on this page. A distributor's generic product page does not establish guaranteed inventory for a specific order quantity. Include your forecast quantities and required delivery date in the request so the manufacturer or authorized supply channel can confirm allocation, production status, and the most appropriate shipping schedule.
What is the best cross-brand equivalent for TAS5186DDVR?
No verified cross-brand drop-in equivalent was identified for TAS5186DDVR. A valid substitute would need the same 44-terminal HTSSOP footprint, six digital-input channels, compatible audio-data timing, compatible control and protection behavior, comparable output capability, and a supply range compatible with 10.8 V to 13.2 V operation. Until a manufacturer confirms those conditions, treat any cross-brand part as a redesign candidate rather than a drop-in replacement.
What design features matter most for a TAS5186DDVR power amplifier board?
The most important design features are high-current routing, thermal management, supply decoupling, and correct digital-audio integration. The manufacturer datasheet identifies a 10.8 V to 13.2 V supply range, greater than 90% efficiency at 1 W, and integrated undervoltage, overtemperature, overload, and short-circuit protection. Use short, wide speaker-output paths, low-impedance supply and ground planes, and the recommended capacitor placement to control switching transients and maintain stable multichannel operation.

Справочные инженерные данные для TAS5186DDVR — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose TAS5186DDVR for a new six-channel digital Class D power stage requiring approximately 60 W-class output per channel, a 10.8 V to 13.2 V supply, and integrated speaker-output protection. Choose TAS5186ADDVR when its improved protection system provides a meaningful design benefit and the manufacturer documentation confirms compatibility with the intended PCB and signal chain. Choose TAS5186DDVRR, TAS5186DDVRRG4, or TAS5186DDVRG4 only after checking the exact ordering code and datasheet because the available comparison information does not establish a meaningful electrical difference. Consider TAS5176DDWR only when its lower 40 W-class rating satisfies the speaker loads and budget. No verified cross-brand drop-in replacement is established, so any competitor part should be treated as a redesign until its footprint, interface, protection, and electrical characteristics are confirmed.

Сравнение с аналогами

Параметр Этот товар TAS5186DDVRR TAS5186ADDVR TAS5186DDVRRG4 TAS5186DDVRG4 TAS5176DDWR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 44-HTSSOP 44-HTSSOP 44-HTSSOP 44-HTSSOP 44-HTSSOP 44-HTSSOP
Amplifier Type 6-channel Class D digital power stage 6-channel Class D digital power stage 6-channel Class D digital power stage 6-channel Class D digital power stage 6-channel Class D digital power stage 6-channel Class D digital power stage
Rated Output Class 60 W per channel 60 W per channel >60 W single-ended at 10% THD+N 60 W per channel 60 W per channel 40 W per channel
Digital Audio Input Yes Yes Yes Yes Yes Yes

Ключевые отличия

  • Higher identified channel-output rating (против TAS5176DDWR)
  • Six-channel integration in one 44-HTSSOP package (против TAS5176DDWR)
  • Selection based on protection-generation needs (против TAS5186ADDVR)

Заметки по проектированию

Validate thermal performance with all intended channels loaded rather than relying on the 210 W aggregate rating. Use the lowest supported speaker impedance and the highest sustained output expected in production. Provide uninterrupted PCB copper beneath and around the 44-HTSSOP, minimize thermal barriers, and test the assembled board inside its enclosure. If the enclosure prevents convection, increase copper area or add a thermal solution without compromising the recommended high-current layout.

Route speaker outputs, supply rails, and power returns as short, wide paths to reduce voltage drop and electromagnetic radiation. Place input, output, and supply-decoupling capacitors at the locations shown in the manufacturer application circuit, with particularly low loop area between each output stage and its local supply connection. Avoid narrow necks between the amplifier, power supply, and speaker connectors, and keep switching-current paths away from digital-audio traces.

Follow the manufacturer datasheet for exposed-pad or thermal-pad connection and keep high-current outputs away from sensitive clock and audio-data nets. Maintain a continuous return reference beneath digital and analog input routing, use point-to-point digital connections where recommended, and verify that the digital-audio source and amplifier agree on clocking, data format, and channel mapping. PCB changes should be validated for bit errors across voltage and temperature limits.

Do not equate a 44-HTSSOP footprint with unconditional drop-in compatibility. Before substituting TAS5186ADDVR, TAS5186DDVRR, TAS5186DDVRRG4, TAS5186DDVRG4, or TAS5176DDWR, compare pin names, exposed-pad requirements, control signals, digital timing, output filtering, protection behavior, and electrical limits. Also confirm that the supply rail remains between 10.8 V and 13.2 V under load and that startup order matches the audio source.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The commercial temperature grade does not by itself establish AEC-Q100 qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not confirmed by the manufacturer page text and require review of the current manufacturer product documentation.

Похожие запросы

TAS5186DDVR datasheet TAS5186DDVR pinout TAS5186DDVR datasheet pdf Texas Instruments TAS5186DDVR TAS5186DDVR 6 channel Class D TAS5186DDVR 210W power stage TAS5186DDVR 44 HTSSOP TAS5186DDVR powered speaker application TAS5186DDVR vs TAS5176DDWR TAS5186DDVR vs TAS5186ADDVR TAS5186DDVR replacement TAS5186DDVR price TAS5186DDVR stock TAS5186DDVR equivalent TAS5186DDVR schematic

Связанные компоненты & термины

Texas Instruments TAS5186DDVR TAS5186DDVRR TAS5186ADDVR TAS5186DDVRRG4 TAS5186DDVRG4 TAS5176DDWR Class D amplifier digital-amplifier power stage audio power amplifier amplifier IC semiconductor HTSSOP-44 surface-mount package digital audio input THD+N signal-to-noise ratio power-stage efficiency short-circuit protection undervoltage protection overtemperature protection powered speaker home-theater amplifier soundbar active subwoofer
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ