TAS5611PHD - 125W Stereo/250W Mono Class-D | Texas Instruments
Артикул: TAS5611PHD ✓ АктивенTAS5611PHD Обзор
A Class-D audio power stage is a switching amplifier category that uses transistor output stages to deliver high audio power efficiently. Unlike a linear Class-AB amplifier, its output transistors operate principally in switching states, reducing conduction losses. PurePath HD, the integrated closed-loop feedback technology used in the TAS5611, helps the device achieve total harmonic distortion below 0.03% while retaining the efficiency advantage of Class-D operation.
The headline capabilities include analog signal input, 125 W stereo or 250 W mono output, support for 4 Ω to 8 Ω speaker loads, and operation from a single 32.5 V supply. The 64-pin HTQFP package measures 14 mm by 14 mm and incorporates an exposed pad that requires careful PCB thermal design. These characteristics make the device suitable for high-power consumer audio, home-theater amplification, powered speakers, and compact professional audio systems.
The PurePath HD architecture is central to the amplifier’s performance. Integrated closed-loop feedback monitors the output waveform and corrects nonlinear distortion introduced by the power stage. In an analog-input implementation, the amplifier accepts a conventional audio signal rather than requiring a digital audio codec, allowing it to operate with preamplifiers, tone-control circuits, volume-control stages, or other line-level sources. Analog input also keeps the signal chain compatible with existing analog audio equipment.
Typical uses include stereo home-theater receivers, powered bookshelf speakers, active subwoofers, compact stereo amplifiers, and single-channel high-output installations. A bridge-tied mono configuration can increase the available power into one speaker load, while the stereo configuration distributes the amplifier’s output between two channels. Appropriate speaker selection and power-supply design remain essential because actual thermal performance depends strongly on the PCB copper area, heat spreading, supply capability, and enclosure ventilation.
The principal design consideration is heat management. The exposed thermal pad must be connected to a properly designed copper heat-spreading area, and the amplifier’s operating mode must be evaluated at the intended load impedance and power level. Inductor selection, speaker filtering, grounding, and high-current supply routing also influence switching noise, output stability, and EMI performance. The manufacturer’s reference layouts should be used as the starting point for a new design.
This page combines the verified 125 W stereo, 250 W mono, 32.5 V, distortion, package, and application information with practical selection guidance, package considerations, and clearly qualified drop-in alternatives. It is intended to help engineers determine whether the TAS5611PHD fits a high-power analog-input Class-D design before beginning board-level implementation.
Аналоги без доработки для TAS5611PHD — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TAS5611PHD (тот же форм-фактор и посадочное место) — отличается по Product Type, Maximum Mono Output Power, Maximum Stereo Output Power, Total Harmonic Distortion.
TAS5613PHD
✅ Прямая заменаУточнить цену
Открыть даташит →TAS5612PHD
✅ Прямая заменаУточнить цену
Открыть даташит →TAS5612APHD
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TAS5611PHD Максимальные параметры и электрические характеристики
| Product Type | Analog-input Class-D audio power stage |
| Топология | PurePath HD |
| Maximum Stereo Output Power | 125 W |
| Maximum Mono Output Power | 250 W |
| Supported Speaker Impedance | 4 ohm to 8 ohm |
| Maximum Supply Voltage | 32.5 V |
| Total Harmonic Distortion | <0.03% |
| Channel Configuration | 1-channel mono or 2-channel stereo |
| Input Type | Analog |
| Корпус | 64-pin HTQFP, 14 mm x 14 mm |
| Exposed Pad | Present |
| Тип монтажа | Surface mount |
Руководство по цоколевке TAS5611PHD в корпусе 64-pin htqfp, 14 mm x 14 mm
Цоколевка для TAS5611PHD (корпус 64-pin htqfp, 14 mm x 14 mm). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для TAS5611PHD.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TAS5611PHD подходит для 6 применениеs: Powered Bookshelf Speakers, Home-Theater Stereo Amplifier, High-Power Subwoofer Amplifier, Compact Hi-Fi Stereo Amplifier, Professional Two-Channel Speaker Amplifier, Multi-Room Audio Amplifier Module.
Powered Bookshelf Speakers
The TAS5611PHD fits powered bookshelf speakers requiring substantial stereo output without the space demanded by a conventional linear power amplifier. Its analog input allows the speaker’s line-level input stage to feed the PurePath HD power stage directly, while its 125 W stereo capability targets 4 Ω to 8 Ω drivers. The 64-pin HTQFP exposed pad can spread heat into the speaker enclosure’s internal ground plane, but sustained output still depends on PCB copper, supply capacity, and enclosure ventilation. Designers should verify thermal rise at the intended power level rather than assuming the maximum catalog rating is continuously available.
Home-Theater Stereo Amplifier
A home-theater stereo power amplifier can use the TAS5611PHD to drive left and right speakers at up to 125 W per channel from a 32.5 V supply. The analog input is compatible with preamplifier outputs, while PurePath HD closed-loop feedback targets distortion below 0.03%. Its Class-D topology improves power efficiency relative to a Class-AB design, although the switching output still requires correct inductor selection, output filtering, grounding, and EMI control. Thermal validation in the receiver or amplifier enclosure is essential because continuous multi-channel operation can heat the exposed-pad area faster than a short listening test.
High-Power Subwoofer Amplifier
The TAS5611PHD can be configured for mono operation to provide up to 250 W into a 4 Ω or 8 Ω subwoofer load. This arrangement concentrates the available output into one channel and is appropriate for active subwoofer platforms needing more than conventional analog power stages can deliver efficiently. The amplifier’s analog input can accept a filtered low-frequency signal from an analog crossover or source stage. Designers must select a correctly rated output inductor, preserve amplifier stability across the intended load network, plan the high-current supply path, and verify that the PCB thermal design sustains the chosen continuous output.
Compact Hi-Fi Stereo Amplifier
The TAS5611PHD is appropriate for compact hi-fi amplifiers where efficient Class-D operation, analog compatibility, and high output capability are important. A line-level source can feed the analog input after the user’s volume-control and tone-control stages, avoiding the digital interface required by many modern integrated amplifiers. The device supports 125 W stereo output into 4 Ω to 8 Ω speakers, but the mechanical enclosure may be much smaller than the electrical power rating suggests. Keep switching nodes compact, provide a low-impedance power-supply connection, and use the exposed pad as part of a deliberate heat-spreading structure.
Professional Two-Channel Speaker Amplifier
For professional audio, the TAS5611PHD can form the power stage of a two-channel amplifier driving 4 Ω or 8 Ω passive speakers. Its 125 W stereo capability and distortion below 0.03% are useful for stage-monitor, small-format PA, and installation-speaker designs that use analog line-level control systems. The closed-loop PurePath HD architecture helps maintain low distortion across the output stage, while Class-D efficiency reduces heat relative to a linear amplifier. Operational protection still depends on suitable load selection, output filtering, robust supply wiring, EMI control, and enclosure cooling validated under the worst expected channel load.
Multi-Room Audio Amplifier Module
The TAS5611PHD can serve as a high-power output module inside a multi-room audio amplifier, particularly for zones driven from an analog distribution bus. Its analog input works with centralized preamplifier and routing circuitry, while its 125 W stereo capability provides generous headroom for residential or hospitality installations. The 64-pin HTQFP package supports compact module construction, although its exposed pad must connect to the board’s thermal structure. Engineers should account for simultaneous zone loading, inrush current, channel activation sequence, amplifier stability, and the possibility of long speaker cables when designing the power and output-filter sections.
Справочные инженерные данные для TAS5611PHD — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TAS5613PHD | TAS5612PHD | TAS5612APHD |
|---|---|---|---|---|
| Package | 64-HTQFP (14 mm x 14 mm) with exposed pad | 64-HTQFP (14 mm x 14 mm) with exposed pad | 64-HTQFP (14 mm x 14 mm) with exposed pad | 64-HTQFP (14 mm x 14 mm) with exposed pad |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Architecture | Analog input | Analog input | Digital input | Digital input |
| Feedback Technology | PurePath HD closed-loop feedback | PurePath HD closed-loop feedback | PurePath HD closed-loop feedback | PurePath HD closed-loop feedback |
Ключевые отличия
- Higher stated mono output capability (против TAS5613PHD)
- Analog input preserves compatibility with conventional preamplifier signals (против TAS5612APHD)
- Specified distortion performance for high-power analog audio (против TAS5612PHD)
Заметки по проектированию
Treat the exposed pad as the primary thermal path. Follow the manufacturer’s exposed-pad land pattern and thermal-layout guidance, connect the pad to the appropriate ground structure, and provide as much uninterrupted PCB copper as the mechanical design allows. Validate the amplifier in its final enclosure with the intended load, supply, and ambient temperature. A 125 W stereo or 250 W mono catalog rating does not guarantee continuous operation without sufficient heat spreading.
Keep the switching power stage and output-filter routing compact because high-current and high-voltage nodes can create EMI and signal-integrity problems. Use short, wide supply and ground paths, place input and filtering components according to the reference design, and keep sensitive analog input routing away from switching nodes. Grounding and return-current paths should be planned as part of the complete power-stage layout rather than added after signal routing.
Do not assume that a shared 64-pin package makes another PurePath HD device electrically interchangeable. The TAS5612 family uses digital input rather than the TAS5611 analog input, and differences in output rating, control signals, feedback connections, and pin functions can prevent direct substitution. Before replacing TAS5611PHD, compare the complete pin-description table, recommended schematic, input circuitry, exposed-pad connections, and output-filter requirements for the selected replacement.
Информация о соответствии
The manufacturer product page identifies TAS5611 as an active product, but the listed technical material does not explicitly establish the requested compliance statuses.