TJA1022T - Dual LIN 2.2A Transceiver | NXP Semiconductors
Артикул: TJA1022T ✓ АктивенTJA1022T Обзор
A LIN transceiver is a physical-layer interface IC within the broader automotive networking hierarchy. It connects a host microcontroller or LIN protocol controller to a low-speed, single-wire vehicle network by translating controller-side logic signals into LIN bus levels and receiving bus signals for the controller. Two integrated transceivers allow one controller to manage two LIN channels while retaining a common device footprint and application architecture.
The TJA1022 is primarily intended for in-vehicle subnetworks operating at baud rates up to 20 kBd. Its stated compliance includes LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. These protocol and automotive-interface specifications make the TJA1022T relevant to distributed vehicle systems in which body, comfort, lighting, seat, door, and other accessory modules exchange commands and diagnostic information over LIN networks.
The NXP datasheet identifies the TJA1022T and TJA1022TK as pin-compatible with the TJA1020, TJA1021, TJA1027, and TJA1029. It also states that the TJA1022, TJA1024, TJA1027, and TJA1029 are software compatible. These compatibility statements support platform reuse, although designers should still verify operating conditions, enabled features, electrical limits, and package dimensions for each selected order code before treating a part as a replacement.
Typical uses include vehicle body-control modules, door and seat controllers, lighting controllers, climate-control interfaces, sensor nodes, and gateway modules that combine LIN communication with microcontroller processing. The dual-channel configuration can simplify boards that must connect multiple LIN subnets while reducing the number of separate physical-layer transceivers required.
When designing around the TJA1022T, preserve the pin compatibility and protocol expectations of the selected TJA1020, TJA1021, TJA1027, or TJA1029 reference design. The LIN bus interface must be reviewed against the manufacturer datasheet for termination, wiring, protection, grounding, and application-specific guidance. This page combines verified manufacturer information, distributor availability, package details, and compatibility options for faster component selection.
This product data adds practical context beyond basic catalog listings by organizing protocol compliance, package compatibility, verified alternative families, bus-focused applications, and sourcing information. It highlights where the TJA1022T fits in a LIN network while clearly separating verified facts from specifications that still require confirmation from the manufacturer datasheet.
Аналоги без доработки для TJA1022T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TJA1022T (тот же форм-фактор и посадочное место) — отличается по Package, Product Type, Maximum Baud Rate, Pin Compatibility.
TJA1020T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TJA1021T/20/C
✅ Прямая заменаУточнить цену
Открыть даташит →TJA1027T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TJA1029T/2Z
✅ Прямая заменаУточнить цену
Открыть даташит →TJA1022T Характеристики
| Product Type | Dual LIN transceiver |
| LIN Channels | 2 channels |
| Maximum LIN Baud Rate | 20 kBd |
| LIN 2.0 Compliance | Compliant |
| LIN 2.1 Compliance | Compliant |
| LIN 2.2 Compliance | Compliant |
| LIN 2.2A Compliance | Compliant |
| SAE J2602 Compliance | Compliant |
| Корпус | SO14 |
| Тип монтажа | Surface mount |
Руководство по цоколевке TJA1022T в корпусе so14
Цоколевка для TJA1022T (корпус so14). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для TJA1022T.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TJA1022T подходит для 6 применениеs: Vehicle Body Control Module, Door and Accessory Control, Automotive Lighting Controller, Climate Control Subnetwork Interface, Automotive Sensor Node, LIN Gateway and Communication Hub.
Vehicle Body Control Module
The TJA1022T fits body-control modules that connect distributed door, lighting, seat, and accessory modules to a host microcontroller. Its two LIN transceivers support vehicle subnetworks at rates up to 20 kBd, while stated compliance with LIN 2.0 through LIN 2.2A and SAE J2602 provides a documented protocol baseline. Placing both physical-layer interfaces in one SO14 device can simplify routing and component selection compared with using separate single-channel transceivers. The controller still needs matching LIN protocol handling, and the final design must verify power, grounding, protection, and bus-integration details against the NXP datasheet.
Рекомендуется
Door and Accessory Control
The TJA1022T is suitable for door-zone controllers, latch modules, window controls, and seat-position nodes connected through a LIN subnet. The documented maximum rate of 20 kBd matches the intended low-speed in-vehicle environment, while two channels can serve nodes that need separate LIN connections. Compatibility with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 supports protocol-oriented platform design. Engineers should use the manufacturer datasheet to confirm bus loading, mode-control behavior, supply limits, and pin-level implementation before approving a drop-in replacement.
Рекомендуется
Automotive Lighting Controller
A lighting-control module can use the TJA1022T when exterior or interior lamps are distributed over a LIN subnet rather than wired directly to the main controller. The device provides two LIN physical-layer channels, each operating within the family's stated 20 kBd capability, and its listed LIN and SAE J2602 compliance supports standardized in-vehicle communication. The dual-channel arrangement may reduce board area and simplify firmware resource allocation. Lamp drivers and diagnostics remain separate functions, so the LIN interface should be evaluated for bus termination, fault behavior, wake-up strategy, and environmental requirements.
Рекомендуется
Climate Control Subnetwork Interface
The TJA1022T can provide the physical interface for climate-control subsystems that distribute sensor, actuator, or panel commands over LIN. A 20 kBd dual-transceiver device aligns with the low-bandwidth, cost-conscious vehicle subnetwork architecture described by NXP. Using one controller with two LIN channels can support separate HVAC and cabin-conditioning subnetworks while preserving a common component footprint. The implementation should account for the number of nodes, bus capacitance, wake-up and sleep requirements, and any protection network required by the vehicle platform.
Рекомендуется
Automotive Sensor Node
Compact sensor nodes can use the TJA1022T as the LIN physical-layer interface when the node must exchange measurements or configuration data with a vehicle network. The stated support for LIN 2.2A and SAE J2602 provides relevant protocol context, while the dual-channel architecture offers flexibility where a node serves more than one LIN connection. A low-speed LIN bus helps integrate distributed sensing without requiring a more complex communications physical layer. The exact supply range, standby current, bus-output capability, and environmental limits must be taken from the complete NXP datasheet before schematic sign-off.
Рекомендуется
LIN Gateway and Communication Hub
The TJA1022T can support a communication hub that bridges a host controller to two independent LIN subnetworks. Its dual-transceiver arrangement is useful when the gateway needs separate bus connections without duplicating the physical-layer component footprint. The 20 kBd maximum rate is consistent with the LIN networks targeted by the manufacturer, and compliance across several LIN revisions supports use in established vehicle platforms. Gateway designs still require independent bus management, termination strategy, fault containment, and software scheduling; physical-layer compatibility alone does not provide protocol routing or arbitration.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TJA1022T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TJA1020T | TJA1021T | TJA1027T | TJA1029T |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SO14 | SO14 | SO14 | SO14 | SO14 |
| Pin Compatibility with TJA1022 | Reference device | Pin compatible | Pin compatible | Pin compatible | Pin compatible |
Ключевые отличия
- Dual-channel integration in one package (против TJA1020T)
- Documented support for LIN 2.2A and SAE J2602 (против TJA1020T)
- Software-compatible LIN platform option (против TJA1029T)
Заметки по проектированию
Use the NXP TJA1022 datasheet land pattern for the SO14 footprint and confirm every pin function before routing the PCB. The verified compatibility statement covers TJA1020, TJA1021, TJA1027, and TJA1029, but it does not establish that every alternative exposes identical mode-control or sleep behavior. Preserve the manufacturer-recommended decoupling placement and keep the LIN interface away from high-current switching nodes to reduce coupled disturbance.
Do not treat pin compatibility or software compatibility as proof that two LIN devices are interchangeable in every operating condition. Before substituting TJA1020T, TJA1021T, TJA1027T, or TJA1029T, compare supply voltage, bus-output current, dominant-state and sleep behavior, wake-up logic, temperature range, qualification, and error handling. This is especially important in modules that share one PCB across several vehicle configurations.
Follow the NXP application guidance for LIN bus wiring, termination, grounding, and protection. A LIN bus is sensitive to network topology and parasitic capacitance, so the selected transceiver must be evaluated with the intended number of nodes, cable lengths, and vehicle harness conditions. Validate signal integrity and fault recovery at the system level rather than relying only on the stated 20 kBd maximum baud rate.
Verify the transceiver supply range and current consumption from the manufacturer datasheet because these values were not exposed in the supplied web results. Account for the supply current of both integrated channels and any local logic when sizing the regulator and decoupling network. Also evaluate the module's sleep and wake architecture, since a communication transceiver can materially influence total standby power even when the host controller is inactive.
Информация о соответствии
The verified NXP product information confirms LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 compliance, but the supplied web snippets do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These values remain unknown rather than being inferred.
