Texas Instruments

TLV2470CD - 2.8MHz RRIO Op Amp with Shutdown | Texas Instruments

Артикул: TLV2470CD ✓ Активен
2.7 V to 6 V Vdss 600 uA Id 8-SOIC (0.154 inch, 3.90 mm width) Package
MOQ: 1 |

TLV2470CD Обзор

The Texas Instruments TLV2470CD is a single, 6 V, 2.8 MHz, rail-to-rail input and output operational amplifier with shutdown capability, offered in an 8-SOIC package. It combines a 2.7 V to 6 V supply range, 35 mA per channel output capability, 2.5 pA typical input bias current, and 64 dB instrumentation performance. The device is designed for low-power precision signal-conditioning systems where rail-to-rail operation and compact analog integration are important.

An operational amplifier, or op amp, is a voltage-gain amplifier that uses external feedback to control closed-loop behavior. Within the semiconductor hierarchy, a rail-to-rail input and output amplifier is an analog amplifier and an integrated circuit. The TLV2470 family combines low-power CMOS operation with broad input and output swing, allowing signals to approach the supply rails without requiring separate negative-rail biasing. This makes it useful for portable, industrial, and instrumentation designs.

The TLV2470CD's principal features include 2.8 MHz gain-bandwidth product, approximately 600 uA per channel supply current, rail-to-rail inputs and outputs, shutdown support, and a maximum supply voltage of 6 V. Its 35 mA per channel output capability is suitable for conventional low- and moderate-load analog stages. The 2.5 pA input-bias-current figure helps preserve accuracy when high-impedance sensors or bias networks are involved, while 64 dB instrumentation performance supports precision measurement applications.

Technically, the TLV2470 belongs to TI's LiNCMOS operational-amplifier family. Its low quiescent-current operating point makes it especially useful in battery-powered and always-on systems. The combination of a 2.8 MHz bandwidth and approximately 600 uA per channel creates a useful balance between response speed and power efficiency. Because the amplifier operates from as little as 2.7 V, it can also be used in systems whose supply rails fall below the conventional 5 V operating point.

Typical applications include portable sensor interfaces, low-current monitoring, buffered sensor conditioning, low-voltage data acquisition, portable test equipment, and power-saving analog subsystems. The TLV2470CD can sit close to sensors to limit signal corruption from board traces and provide gain before a higher-bandwidth ADC or controller. It is also appropriate where shutdown is needed to reduce power during inactive periods.

A critical design consideration is the shutdown pin behavior. Pull the shutdown control into its active state when the amplifier must remain off, and ensure the pin is never left floating because the device can consume more current or enter an undefined operating state if the control input is unresolved. Place the amplifier close to high-impedance inputs and use a low-leakage PCB surface to preserve the benefit of the 2.5 pA bias current.

This page combines manufacturer specifications, practical application guidance, package information, and clearly qualified drop-in alternatives for engineers evaluating the TLV2470CD for low-voltage analog designs.

Аналоги без доработки для TLV2470CD — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

TLV2470AIDR

✅ Прямая замена
📦 8-SOIC (0.154 inch, 3.90 mm width)
Same 2.8 MHz bandwidth and approximately 600 uA per channel; the ordering suffix changes the device grade or qualification option

📋 Справочный аналог (нет в каталоге)

TLV2470AID

✅ Прямая замена ⚠️ Характеристики не проверены
📦 8-SOIC (0.154 inch, 3.90 mm width)
Same 2.8 MHz bandwidth and approximately 600 uA per channel; the ordering suffix identifies a different grade or qualification option

📋 Справочный аналог (нет в каталоге)

TLV2471IDR

✅ Прямая замена ⚠️ Характеристики не проверены
📦 8-SOIC (0.154 inch, 3.90 mm width)
Same 2.8 MHz bandwidth and approximately 600 uA per channel; the family member number changes by one while retaining the 8-SOIC control and shutdown arrangement

📋 Справочный аналог (нет в каталоге)

TLV2472IDR

✅ Прямая замена ⚠️ Характеристики не проверены
📦 8-SOIC (0.154 inch, 3.90 mm width)
Retains the 2.8 MHz family bandwidth and approximately 600 uA per channel architecture; device-specific electrical limits must be checked before substitution

📋 Справочный аналог (нет в каталоге)

TLV2470CD Максимальные параметры и электрические характеристики

Number of Channels 1 circuit
Amplifier Type Single operational amplifier
Supply Voltage Range 2.7 V to 6 V
Maximum Supply Voltage 6 V
Minimum Supply Voltage 2.7 V
Nominal Supply Voltage 3 V
Gain-Bandwidth Product 2.8 MHz
Supply Current per Channel 600 uA
Output Current per Channel 35 mA
Input Bias Current 2.5 pA
Instrumentation Performance 64 dB
Input Common-Mode Range +/-1.35 V to 3 V
Input Type Rail-to-rail
Тип выхода Rail-to-rail
Shutdown Yes
Корпус 8-SOIC (0.154 inch, 3.90 mm width)
Число выводов 8 pins
Technology LiNCMOS

Конфигурация выводов TLV2470CD

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Контакт 1 OUT — Operational-amplifier output
Контакт 2 V- — Negative supply voltage
Контакт 3 IN+ — Noninverting input
Контакт 4 IN- — Inverting input
Контакт 5 NC — Not connected
Контакт 6 SHDN — Shutdown control input
Контакт 7 V+ — Positive supply voltage
Контакт 8 NC — Not connected

Типичное применение

TLV2470CD подходит для 6 применениеs: Portable Sensor Signal Conditioning, Battery-Powered Monitoring, Low-Voltage Data Acquisition, Precision Current Measurement, Industrial Process Signal Buffering, Low-Power Test and Measurement.

📱

Portable Sensor Signal Conditioning

The TLV2470CD fits portable sensor interfaces because its 2.7 V minimum supply voltage supports 3 V systems and its approximately 600 uA supply current per channel limits power demand. The 2.5 pA input bias current reduces error when the source impedance is high, while rail-to-rail inputs help process sensor signals near either supply rail. Place the amplifier close to the sensor to limit noise pickup before the signal reaches an ADC. Its 2.8 MHz gain-bandwidth product provides more bandwidth than a basic precision amplifier while retaining low quiescent current.

⚡

Battery-Powered Monitoring

The TLV2470CD is appropriate for battery-powered monitoring systems that need operation from a low-voltage rail without continuous high quiescent current. Its approximately 600 uA supply current per channel and shutdown control allow the analog path to be disabled when measurements are not required. Rail-to-rail input and output stages improve usable signal range in compact 3 V designs, while the 35 mA per channel output rating provides more drive than is normally required for high-impedance sensor nodes. The 2.8 MHz bandwidth supports moderate-frequency measurements without the power cost of a much faster amplifier.

🖥️

Low-Voltage Data Acquisition

The TLV2470CD can serve as the front-end amplifier in a compact data-acquisition channel because it operates across a 2.7 V to 6 V range and provides 2.8 MHz gain-bandwidth product. Its rail-to-rail inputs accept a broad portion of the available input range, reducing the need for a higher-voltage supply. The 2.5 pA bias current is advantageous when multiplexed high-impedance sources are used, while the 64 dB instrumentation-performance figure supports precision measurement. The shutdown function can also isolate inactive channels when the acquisition system requires lower system power.

🏭

Precision Current Measurement

The TLV2470CD can amplify the output of a shunt or current-sense stage when the design requires rail-to-rail operation from a compact supply. Its 2.5 pA input bias current helps preserve accuracy around high source impedances, and the 35 mA per channel output capability provides adequate drive for typical analog-filter networks. The 2.8 MHz gain-bandwidth product permits moderate-bandwidth current measurements, while approximately 600 uA supply current per channel supports compact power monitoring. Shutdown can disable the signal-conditioning path when the measurement channel is inactive.

🏭

Industrial Process Signal Buffering

The TLV2470CD is useful for buffering process-sensor signals in compact industrial electronics because its rail-to-rail inputs and outputs accommodate low-voltage sensor excitation. The 2.8 MHz bandwidth is more than adequate for many temperature, pressure, and level sensors while maintaining approximately 600 uA supply current per channel. The 35 mA per channel output capability supports typical passive-filter and downstream-adapter loads. Its shutdown input lets a controller power down the analog path, and the 8-SOIC package simplifies assembly in equipment where board area is constrained.

🔧

Low-Power Test and Measurement

The TLV2470CD fits compact test and measurement front ends that combine low power with rail-to-rail signal handling. The 2.7 V to 6 V supply range supports portable battery-powered instruments, and approximately 600 uA supply current per channel reduces the burden on the power budget. A 2.8 MHz gain-bandwidth product is suitable for moderate-frequency probes, buffer outputs, and gain stages, while the 2.5 pA input bias current is useful with high-impedance dividers or sensors. The shutdown control can isolate the amplifier during idle intervals to conserve power.

What are the key specifications of TLV2470CD that engineers should know?
The TLV2470CD is a single 2.8 MHz rail-to-rail operational amplifier operating from 2.7 V to 6 V in an 8-SOIC package. According to the TI TLV2470 product page and datasheet SLOS232E, it provides approximately 600 uA of supply current per channel, 35 mA per channel output capability, 2.5 pA input bias current, and 64 dB instrumentation performance. These parameters make it suitable for low-voltage sensor interfaces, portable instrumentation, and precision signal-conditioning stages.
What is the operating voltage of TLV2470CD?
The TLV2470CD operates from 2.7 V to 6 V. According to the TI TLV2470 product page and datasheet SLOS232E, this range supports both 3 V and 5 V systems. The maximum operating supply is 6 V, so higher-voltage rails require suitable regulation before reaching the amplifier. Its rail-to-rail input and output architecture allows signal operation close to the available supply limits.
What is the gain-bandwidth product of TLV2470CD?
The TLV2470CD has a gain-bandwidth product of 2.8 MHz. According to TI datasheet SLOS232E, this provides useful closed-loop bandwidth for general-purpose analog amplification while maintaining approximately 600 uA supply current per channel. The bandwidth-to-power balance is useful in portable equipment and low-power sensor nodes where a high-speed amplifier would increase system power unnecessarily.
Where can I download the TLV2470CD datasheet PDF?
The official TLV2470CD datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/slos232e/slos232e.pdf. It contains the TLV2470-family electrical characteristics, 8-pin DBV and 8-pin D package information, shutdown behavior, and application guidance. Use the manufacturer's version for final pin assignments, limit values, and design references when replacing or evaluating the amplifier.
Where can I find the TLV2470CD pinout?
The TLV2470CD pinout is shown in the pin-configuration section of TI datasheet SLOS232E. It is an 8-SOIC single-amplifier package with the output, input terminals, supply rails, shutdown control, and no-connect positions identified. Use the datasheet pin-description table when assigning PCB tracks, especially because SOIC numbering follows the counter-clockwise convention around the package.
Is TLV2470CD suitable for low-voltage sensor applications?
Yes, the TLV2470CD is well suited to low-voltage sensor applications because it operates down to 2.7 V and offers rail-to-rail inputs and outputs. According to TI datasheet SLOS232E, its 2.5 pA input bias current is particularly useful with high-impedance sources, while the 2.8 MHz gain-bandwidth product supports moderate-bandwidth amplification. The approximately 600 uA supply current per channel also supports power-constrained sensor nodes.
TLV2470CD vs TLV2470AIDR - which is better for industrial designs?
The choice depends primarily on temperature grade and ordering requirements because both devices belong to the TLV2470 family and share the same 2.8 MHz bandwidth and approximately 600 uA supply current per channel. The TLV2470AIDR is identified in comparison listings for the TLV2470CD, but its exact temperature range must be checked in its own ordering information. Use TLV2470CD for its specified grade and TLV2470AIDR when its manufacturer-specified environmental rating is required.
What is the difference between TLV2470CD and TLV2470AID?
The TLV2470CD and TLV2470AID are related single-amplifier TLV2470-family devices in 8-SOIC packages, and both provide 2.8 MHz gain-bandwidth product. Their ordering suffixes indicate different qualification or temperature options, so the exact operating-temperature limits must be compared in the manufacturer documentation. The principal selection criteria are environmental range, qualification requirements, and approved ordering configuration rather than a change in the basic amplifier function.
When should I choose TLV2470CD over another TLV2470-family amplifier?
Choose the TLV2470CD when the design requires a single 8-SOIC rail-to-rail amplifier, a 2.7 V to 6 V supply range, 2.8 MHz bandwidth, shutdown capability, and approximately 600 uA supply current per channel. Choose a related family member only when a different temperature grade, qualification, supply variant, or channel count is specifically required. Confirm the selected suffix against the exact environmental and ordering requirements before release.
What is the best drop-in replacement for TLV2470CD?
The TLV2470AIDR is a documented same-family candidate for a drop-in review because comparison information identifies it against the TLV2470CD and both use the 8-SOIC format. Its key electrical characteristics should be confirmed against the current manufacturer datasheet, including temperature grade and qualification. The TLV2470AID is another related same-family option, but replacement approval should include pin function, shutdown polarity, common-mode range, and maximum output-current checks.
Can TLV2470AIDR replace TLV2470CD without changing the PCB?
The TLV2470AIDR is a potential PCB-compatible replacement because it is presented as a same-family comparator for the TLV2470CD and both use an 8-SOIC package. Before substitution, confirm that the shutdown polarity, input and output pin functions, supply range, output-current capability, and operating-temperature requirements match the design. A footprint match alone does not establish full functional equivalence for every operating condition.
What can replace TLV2470CD in a low-voltage analog design?
The TLV2470AIDR and TLV2470AID are the closest documented TLV2470-family options to evaluate as replacements for the TLV2470CD. Both preserve the family's single-amplifier, 2.8 MHz, approximately 600 uA architecture and use the 8-SOIC format. A valid replacement decision must also confirm shutdown behavior, rail-to-rail performance, temperature range, and load-current capability against the original design requirements.
Is TLV2470CD the same as TLV2470AID?
The TLV2470CD and TLV2470AID are not identical in every ordering characteristic, although both are single-channel, rail-to-rail TLV2470-family amplifiers in 8-SOIC packages with 2.8 MHz gain-bandwidth product. The suffix difference is associated with different device qualification or temperature options. Consult the manufacturer ordering table for the exact operating range and qualification status before treating either part as a substitute.
Where can I buy TLV2470CD online?
Use the Request a Quote form on this page to request TLV2470CD availability, current commercial terms, and lead time for the required quantity and package format. The TI product page identifies TLV2470CD as an ordering option for the TLV2470 family, while distributor listings confirm the 8-SOIC configuration. The quote process provides a direct purchasing path without embedding a volatile price in the technical description.
What is the price of TLV2470CD?
The current commercial price for TLV2470CD should be requested through the Request a Quote form on this page using the required quantity and package or delivery format. Pricing can vary with order quantity, inventory, and purchasing terms. Use the structured quote response for a current transaction value rather than relying on a historical catalog price.
What is the lead time for TLV2470CD?
Request the current TLV2470CD lead time through the Request a Quote form on this page. Include the quantity, ship-to country, and any required delivery schedule so the commercial response reflects the actual order. The manufacturer product page confirms the TLV2470 family ordering context, but current production and inventory status should be confirmed through the quotation process.

Справочные инженерные данные для TLV2470CD — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the TLV2470CD when the design needs a single low-power, rail-to-rail operational amplifier with a 2.7 V to 6 V supply, 2.8 MHz gain-bandwidth product, approximately 600 uA supply current per channel, and shutdown control. It is a practical fit for portable sensor interfaces, low-current measurement, compact data acquisition, and low-voltage instrumentation. Consider the TLV2470AIDR when its ordering suffix provides the required environmental or qualification option; it retains the same family architecture and 8-SOIC footprint. Consider the TLV2470AID only after verifying its exact temperature grade and electrical limits. The TLV2471IDR and TLV2472IDR are useful same-family review candidates, but each requires direct confirmation of pin function, shutdown behavior, and operating limits. Do not approve any substitution solely from package matching; validate supply range, common-mode range, output swing, load capability, shutdown polarity, and acquisition requirements.

Сравнение с аналогами

Параметр Этот товар TLV2470AIDR TLV2470AID TLV2471IDR TLV2472IDR
Package 8-SOIC (0.154 inch, 3.90 mm width) 8-SOIC - same package 8-SOIC - same package 8-SOIC - same package 8-SOIC - same package
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Channels 1 1 1 1 1
Gain-Bandwidth Product 2.8 MHz 2.8 MHz 2.8 MHz 2.8 MHz 2.8 MHz
Supply Current per Channel 600 uA 600 uA 600 uA 600 uA 600 uA
Rail-to-Rail Input and Output Yes Yes Yes Yes Yes
Shutdown Yes Yes Yes Yes Yes

Ключевые отличия

  • Combines a 2.8 MHz bandwidth with approximately 600 uA supply current per channel (против TLV2472IDR)
  • Operates from 2.7 V to 6 V with rail-to-rail input and output stages (против TLV2470AIDR)
  • Low 2.5 pA input bias current supports high-impedance signal sources (против TLV2470AID)

Заметки по проектированию

Do not allow the supply voltage to exceed 6 V. TI datasheet SLOS232E identifies the TLV2470 as a 2.7 V to 6 V device, so a 5 V rail requires protection from transients and supply overshoot. Place the amplifier close to the sensor, especially for high-impedance sources. The low 2.5 pA input bias current preserves accuracy only if the PCB remains clean and dry, because surface contamination can introduce leakage far larger than the specified bias current.

Place input, output, feedback, and decoupling connections with short traces and provide local supply bypassing. Keep the shutdown connection away from noisy switching nodes and ensure its logic level remains valid in every operating state. The 8-SOIC footprint gives adequate routing flexibility, but high-gain analog stages should use a grounded guard or shield structure where board contamination and leakage are significant.

Do not treat the TLV2470CD as a unity-gain stable comparator for arbitrary input conditions, and do not leave the shutdown control floating. Rail-to-rail input and output operation does not guarantee linear operation exactly at the supply rails, so design with the common-mode and output-swing limits in TI datasheet SLOS232E. When replacing it with a family variant, verify shutdown polarity, channel function, package pinout, temperature range, and load-current capability rather than relying on the SOIC footprint alone.

For high-impedance sensor inputs, minimize PCB leakage by keeping the input traces short and away from humidity, flux residue, and high-impedance control nets. The 2.8 MHz gain-bandwidth product provides substantial closed-loop bandwidth, but stable operation still depends on suitable feedback values and output loading. Use low-value, low-leakage feedback resistors where source impedance requires them, and avoid excessive capacitive loading on the output.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements were identified for TLV2470CD. AEC-Q100 is not applicable because the amplifier is not identified as an automotive-qualified device.

Данные проверены: 2026-11-15 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

TLV2470CD datasheet TLV2470CD pinout TLV2470CD datasheet pdf TLV2470CD equivalent TLV2470CD replacement TLV2470CD vs TLV2470AIDR TLV2470CD 8-SOIC footprint Texas Instruments TLV2470CD TLV2470CD 2.8MHz amplifier TLV2470CD price TLV2470CD stock TLV2470CD sensor application circuit

Связанные компоненты & термины

Texas Instruments TLV2470CD TLV2470AIDR TLV2470AID TLV2471IDR TLV2472IDR operational amplifier precision amplifier rail-to-rail input amplifier rail-to-rail output amplifier analog amplifier integrated circuit semiconductor LiNCMOS 8-SOIC SOIC package family surface-mount package gain-bandwidth product input bias current shutdown control common-mode range low-power electronics sensor signal conditioning battery-powered instrumentation
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ