TPS2041BQDBVRQ1 - Automotive 0.5A USB Power Switch SOT-23-5 | TI
Артикул: TPS2041BQDBVRQ1 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.18 | $1,18 |
| 10 | $1.02 | $10,20 |
| 100 | $0.86 | $86,00 |
| 500 | $0.74 | $370,00 |
| 1.000 | $0.61 | $610,00 |
TPS2041BQDBVRQ1 Обзор
A USB power-distribution switch is a high-side load switch that sits between a 5 V bus and a downstream USB port or peripheral. It protects the host system from short circuits and over-current events by combining an N-channel MOSFET pass element with built-in current-limit, thermal shutdown, and undervoltage lockout. When the host asserts the active-low enable input, the switch closes to deliver current; when disabled, it presents a high-impedance path to block back-feeding.
Key features include an accurate current limit at approximately 1 A, an integrated 105 mΩ N-channel MOSFET, thermal and short-circuit protection, an active-low logic enable input, and a flag output that asserts on fault. The SOT-23-5 footprint keeps board area minimal, making the part suitable for compact infotainment, telematics, and body-electronics modules where PCB real estate is constrained.
The TPS2041BQDBVRQ1 uses an N-channel MOSFET pass element driven by an internal charge pump to achieve true low-RDS(on) high-side switching. This architecture minimizes I²R conduction loss on the 5 V rail and keeps thermal rise modest at the 500 mA continuous rating. The fixed current limit prevents the upstream automotive bus from sagging during load transients, while the thermal-shutdown circuit latches the switch off on excessive junction temperature.
Typical applications include USB port power switching in automotive head units, body control modules, and rear-seat infotainment hubs. The device is also used to switch individual loads downstream of an LDO, providing fault isolation between branches. The wide input range (2.7 V to 5.5 V) tolerates cold-crank and load-dump conditions typical of 12 V automotive systems after regulation.
When designing with this device, ensure the input supply is well-decoupled with at least 1 µF of ceramic capacitance placed close to IN. Avoid continuous operation above 500 mA and verify thermal performance against the SOT-23-5 θJA. This page synthesizes distributor pricing, drop-in alternatives, and design considerations not found in the manufacturer datasheet alone.
Аналоги без доработки для TPS2041BQDBVRQ1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TPS2041BDBVR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS2042BQDBVRQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS2051BQDBVRQ1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS2041BQDBVRQ1G4
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TPS2041BQDBVRQ1 Максимальные параметры и электрические характеристики
| Part Number | TPS2041BQDBVRQ1 |
| Switch Type | High-Side Power Distribution Switch |
| Количество выходов | 1 |
| Диапазон входного напряжения | 2.7 V to 5.5 V |
| Continuous Load Current | 500 mA |
| On-Resistance (RDS(on)) | 105 mΩ (typical) |
| Ограничение тока | 1 A (typical, factory-trimmed) |
| Enable Input | Active-Low |
| Тепловая защита | Yes (with auto-retry) |
| Short-Circuit Protection | Yes |
| Fault Flag Output | Yes (active-low OC) |
| Рабочая температура | -40 C to +125 C |
| Корпус | SOT-23-5 (DBV) 2.90 mm x 1.60 mm |
| Тип монтажа | Surface Mount |
| Уровень MSL | 1 |
| Automotive Qualification | AEC-Q100 Qualified |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Конфигурация выводов TPS2041BQDBVRQ1
| Контакт 1 | IN — Input supply voltage (2.7 V to 5.5 V); connect to upstream 5 V rail with local decoupling |
| Контакт 2 | GND — Ground reference |
| Контакт 3 | IN — Input supply voltage (internally bonded to pin 1) |
| Контакт 4 | EN — Active-low enable input; drive low to turn the switch on, high to disable |
| Контакт 5 | OUT — Switched output to load (USB VBUS or downstream rail) |
Типичное применение
TPS2041BQDBVRQ1 подходит для 6 применениеs: Automotive Head Unit USB Port Power Switching, Body Control Module (BCM) Load Switching, Rear-Seat Infotainment USB Hub, Telematics Control Unit (TCU) Power Rail Switching, Industrial 5 V Load Protection, USB Charging Port Downstream of LDO.
Automotive Head Unit USB Port Power Switching
The TPS2041BQDBVRQ1 sits between the head unit's internal 5 V rail and each USB VBUS pin, providing per-port overcurrent protection and fault isolation. Its AEC-Q100 qualification and -40 C to +125 C operating range handle the temperature extremes of an in-dash infotainment environment, while the 105 mΩ RDS(on) limits full-load conduction loss to roughly 53 mW per port. The active-low enable input simplifies interface to common USB power controllers that assert low to enable downstream power, and the built-in fault flag can drive a GPIO interrupt for diagnostic reporting on USB overcurrent events.
Рекомендуется
Body Control Module (BCM) Load Switching
In body control modules, the TPS2041BQDBVRQ1 provides protected high-side switching for individual downstream loads, isolating faults between branches such as interior lighting controllers, door modules, or sensor rails. The 1 A current limit prevents upstream automotive bus sagging during a downstream short, while the integrated thermal shutdown protects the SOT-23-5 package from sustained fault currents. The 2.7 V to 5.5 V input range rides through cold-crank transients on 12 V battery systems after regulation, making it a robust choice for distributed BCM architectures.
Рекомендуется
Rear-Seat Infotainment USB Hub
Each USB port in a rear-seat entertainment hub can be protected by a dedicated TPS2041BQDBVRQ1, giving per-port current limiting and fault indication to the host processor. The device's small SOT-23-5 footprint allows multiple switches to be placed in tight spaces behind the rear-seat display panel. The 500 mA continuous rating matches the USB 2.0 standard port current, and the 1 A current limit accommodates brief inrush events from downstream device hot-plug without nuisance tripping, while still protecting the wiring harness in a sustained fault.
Рекомендуется
Telematics Control Unit (TCU) Power Rail Switching
Telematics modules often need to selectively power-down sub-circuits when the vehicle is parked to limit battery drain, and the TPS2041BQDBVRQ1 provides the controllable high-side switch for those rails. The active-low enable input allows the TCU's microcontroller to assert low during sleep mode to fully disconnect downstream 5 V loads, drawing essentially zero quiescent current from the switched rail. The AEC-Q100 qualification and wide temperature range suit the under-dash or roof-mounted TCU installation environment.
Рекомендуется
Industrial 5 V Load Protection
Beyond automotive, the TPS2041BQDBVRQ1 also fits industrial 5 V load-protection applications where its 105 mΩ RDS(on) and 1 A current limit provide efficient, fault-isolated power switching. PLCs, sensor hubs, and HMI panels benefit from the same per-port current-limit architecture used in USB designs. The wide 2.7 V to 5.5 V input range allows the device to operate directly from a regulated 5 V industrial bus or from the output of a 3.3 V LDO with margin.
Рекомендуется
USB Charging Port Downstream of LDO
The TPS2041BQDBVRQ1 can be placed between a 5 V LDO and a USB charging port to provide a second layer of fault isolation in addition to the LDO's current limit. This two-stage protection architecture allows the LDO to source average load while the TPS2041BQDBVRQ1 handles the instantaneous fault current and limits peak dissipation. The fault flag output can interrupt the system MCU to log or display the USB fault condition for service diagnostics.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TPS2041BQDBVRQ1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TPS2041BDBVR | TPS2042BQDBVRQ1 | TPS2051BQDBVRQ1 | TPS2041BQDBVRQ1G4 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 (DBV) | SOT-23-5 (DBV) - same | SOT-23-5 (DBV) - same | SOT-23-5 (DBV) - same | SOT-23-5 (DBV) - same |
| Number of Channels | 1 | 1 | 2 | 1 | 1 |
| Continuous Load Current | 500 mA | 500 mA | 500 mA per channel | 500 mA | 500 mA |
| On-Resistance (typ) | 105 mΩ | 80 mΩ | 105 mΩ | 105 mΩ | 105 mΩ |
| Current Limit (typ) | 1 A | 0.9 A | 1 A per channel | 1 A | 1 A |
| Enable Polarity | Active-Low | Active-Low | Active-Low | Active-High | Active-Low |
| AEC-Q100 Qualified | Yes | No | Yes | Yes | Yes |
Ключевые отличия
- AEC-Q100 qualified for automotive USB power switching (против TPS2041BDBVR)
- Dual-channel option available in same footprint (против TPS2042BQDBVRQ1)
- Active-low enable polarity for USB controller compatibility (против TPS2051BQDBVRQ1)
Заметки по проектированию
Estimated: At VIN=5 V, VOUT drop ~0.05 V (RDS(on)*I), and 500 mA continuous load, the steady-state power dissipation is roughly 0.13 W. The SOT-23-5 (DBV) package has a typical theta_JA around 220 C/W on a standard JEDEC 1-square-inch 2-oz copper test board, yielding a junction temperature rise of approximately 28 C above ambient at 500 mA. Confirm against the manufacturer's thermal curve in the datasheet for your specific PCB copper area; reduce load or improve copper pour if Tj approaches 125 C.
Place a low-ESR ceramic bypass capacitor of at least 1 µF as close as possible to the IN pin (pin 1 and pin 3, which are internally bonded). Add a 0.1 µF ceramic in parallel for high-frequency decoupling of the upstream 5 V rail. The OUT pin should also have a local bulk capacitor (typically 1 µF to 10 µF) to limit inrush currents when the switch closes into a capacitive load. Keep the GND trace short and wide to minimize ground bounce during load transients.
Do not drive the EN pin with a floating signal; if left open, the internal pull-up keeps the switch disabled, but a floating enable can pick up noise and cause intermittent turn-on. Verify that the upstream supply does not exceed 5.5 V during load-dump transients - this part is designed for post-regulator 5 V rails, not direct 12 V battery connection. Ensure the load capacitance on OUT does not exceed the datasheet's recommended maximum, otherwise the inrush current at switch turn-on can trip the current-limit circuit prematurely.
Информация о соответствии
AEC-Q100 automotive qualified per TI -Q1 designation. RoHS and lead-free compliant per TI product page. REACH compliance not explicitly listed; treated as compliant by default under TI's standard declaration. Halogen-free status not stated in available data.
