TPS7A1601DGNR - 60V 100mA Ultra-Low IQ LDO | Texas Instruments
Артикул: TPS7A1601DGNR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.95 | $1,95 |
| 10 | $1.75 | $17,50 |
| 100 | $1.42 | $142,00 |
| 500 | $1.18 | $590,00 |
| 1.000 | $0.98 | $980,00 |
TPS7A1601DGNR Обзор
An LDO (low-dropout) linear regulator is a voltage regulator that maintains a stable output even when input and output voltages are close, using a pass transistor in its linear region. LDOs are a subclass of linear regulators within the broader power management IC family, valued for low output noise and simplicity. The TPS7A1601 belongs to this category, optimized for ultra-low standby power in always-on systems.
Key features include a typical quiescent current of only 5 uA, dramatically extending battery life in continuous or sporadic (power backup) applications. The device integrates a CMOS-logic-compatible enable pin and an open-drain active-high power-good (PG) output with user-programmable delay for power-rail sequencing. Dropout voltage is typically 300 mV at 100 mA load, and the part includes overcurrent and thermal shutdown protection.
The CMOS architecture pairs a precision 1.2 V bandgap reference and error amplifier with a P-channel MOSFET pass element, achieving low IQ without sacrificing transient response. The device is stable with ceramic output capacitors as small as 2.2 uF, simplifying the BOM. The open-drain PG output can be pulled up to any rail up to 60 V, enabling flexible level-shifting.
Typical applications include battery-powered industrial sensors, automotive body control modules, and always-on microcontroller power supplies. The 60 V rating allows direct connection to 12 V and 24 V industrial buses with full tolerance for load-dump transients, eliminating a pre-regulator stage.
Design consideration: at high input-to-output differentials, dissipation is significant (e.g., 24 V to 3.3 V at 100 mA is about 2.1 W), so PCB copper area under the exposed pad must be sized for thermal performance, and the programmable PG delay should be set to match MCU reset requirements.
Аналоги без доработки для TPS7A1601DGNR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TPS7A1601DGNR (тот же форм-фактор и посадочное место) — отличается по Input Voltage Range, Package, Power Good Output, Protection Features.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TPS7A1601QDGNRQ1
✅ Прямая замена✓ В наличии
$1.66 / шт.
Открыть даташит →TPS7A1600DGNR
⚡ Тот же корпус ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TPS7A1633QDGNRQ1
⚡ Тот же корпус📋 Справочный аналог (нет в каталоге)
TPS7A4901DGNR
⚡ Тот же корпус📋 Справочный аналог (нет в каталоге)
LT3014BEDD
⚡ Тот же корпус ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TPS7A1601DGNR Максимальные параметры и электрические характеристики
| Тип выхода | Adjustable |
| Диапазон выходного напряжения | 1.2 V to 18.5 V |
| Максимальный выходной ток | 100 mA |
| Диапазон входного напряжения | 3 V to 60 V |
| Ток покоя | 5 uA (typical) |
| Напряжение падения | 300 mV at 100 mA (typical) |
| Опорное напряжение | 1.2 V |
| Вывод разрешения | Yes (CMOS-logic compatible) |
| Выход Power Good | Open-drain active-high PG with programmable delay |
| Protection Features | Overcurrent, thermal shutdown |
| Output Capacitor | Stable with 2.2 uF ceramic minimum |
| Корпус | 8-HVSSOP (DGN) with exposed pad |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant (per distributor listing) |
Конфигурация выводов TPS7A1601DGNR
| Контакт 1 | IN — Input supply, 3 V to 60 V |
| Контакт 2 | EN — Enable input, CMOS-logic compatible |
| Контакт 3 | GND — Ground |
| Контакт 4 | FB — Feedback input for adjustable output |
| Контакт 5 | DELAY — Power-good delay programming pin |
| Контакт 6 | PG — Power good, open-drain active-high output |
| Контакт 8 | OUT — Regulated output voltage, 1.2 V to 18.5 V |
| Контакт PAD | Exposed Pad — Ground connection and thermal dissipation |
Типичное применение
TPS7A1601DGNR подходит для 6 применениеs: Battery-Powered Industrial Sensors, Automotive Body Control Modules, 24 V Industrial Bus Post-Regulator, Always-On Microcontroller Supplies, Power Backup and Sporadic-Load Systems, Metering and Smart Grid Nodes.
Battery-Powered Industrial Sensors
The TPS7A1601DGNR fits battery-powered industrial sensors because its 5 uA typical quiescent current preserves battery capacity over multi-year deployments, while the 60 V input tolerance handles solar-charged or 24 V bus supplies directly. Placed between the battery rail and the sensor analog front end with a 2.2 uF ceramic output capacitor, it provides a clean regulated rail with overcurrent and thermal shutdown protection. The enable pin allows the system MCU to disconnect the rail entirely during sleep, and the power-good output confirms regulation before waking the sensor chain.
Рекомендуется
Automotive Body Control Modules
In automotive body control modules, the AEC-Q100 qualified TPS7A1601QDGNRQ1 variant provides an always-on standby rail that survives 60 V load-dump transients on 12 V battery systems. The 5 uA quiescent draw keeps key-off battery drain minimal, directly affecting cold-cranking reserve. The CMOS-compatible enable connects to ignition-sense logic, while the open-drain power-good output with programmable delay sequences the MCU reset. Use the same HVSSOP-8 (DGN) footprint as the standard DGNR part to unify PCB layout across consumer and automotive builds.
Рекомендуется
24 V Industrial Bus Post-Regulator
The 60 V input rating lets the TPS7A1601DGNR connect directly to 24 V industrial control buses, including tolerance for surge transients, eliminating a pre-regulator stage that an ordinary 35 V LDO would require. Supplying up to 100 mA to PLC I/O, isolation-side rails, or interface transceivers, the device pairs well with a buck converter downstream at higher loads. Designers must budget thermal margin: 24 V to 5 V at 100 mA dissipates about 1.9 W, so generous copper pour under the exposed pad is essential for reliable junction temperatures.
Рекомендуется
Always-On Microcontroller Supplies
For always-on MCU domains in smart meters and IoT nodes, the TPS7A1601DGNR provides a regulated 1.8 V to 3.3 V rail from a wide input, drawing only 5 uA itself. The programmable power-good delay can be matched to the MCU reset requirement, ensuring the processor boots only after the rail is stable. Its 2.2 uF ceramic-output stability reduces board area and BOM cost. In sporadic-operation designs, the enable pin gates the entire domain, and the 60 V tolerance supports energy-harvest or rectified-AC inputs without additional protection.
Рекомендуется
Power Backup and Sporadic-Load Systems
The TPS7A16 family is explicitly designed by TI for continuous or sporadic (power backup) battery applications where ultra-low quiescent current extends system life. In backup circuits feeding RTC, metering, or alarm circuitry, the 5 uA IQ means the regulator itself consumes negligible standby energy compared to the load. The wide 3 V to 60 V input accommodates battery stacks, supercapacitor banks, and rectified AC. The open-drain PG output pulls up to any rail up to 60 V, giving flexible logic-level signaling to backup controllers regardless of the supervisory supply voltage.
Рекомендуется
Metering and Smart Grid Nodes
Electricity meter and smart-grid node designs benefit from the TPS7A1601DGNR because it tolerates rectified mains-derived DC inputs up to 60 V while drawing microamp-level quiescent current, preserving battery-backed accuracy circuits during outages. The device powers MCU and metrology analog rails at up to 100 mA with low output noise for the ADC front end. Pair it with an isolated interface such as ISO1050 for communication. Designers should implement the programmable PG delay to hold the MCU in reset until the metrology rail settles after power recovery.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TPS7A1601DGNR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TPS7A1601QDGNRQ1 | TPS7A1633QDGNRQ1 | TPS7A4901DGNR |
|---|---|---|---|---|
| Package | 8-HVSSOP (DGN) | 8-HVSSOP (DGN) - same | 8-HVSSOP (DGN) - same | 8-HVSSOP (DGN) - center pad differs, verify footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Output Current | 100 mA | 100 mA | 100 mA | 1 A |
| Output Voltage | Adjustable 1.2 V to 18.5 V | Adjustable 1.2 V to 18.5 V | Fixed 3.3 V | Adjustable (1.2 V class) |
| Automotive Grade (AEC-Q100) | No (standard grade) | Yes | Yes | No |
| Noise / Positioning | Ultra-low IQ, battery life focused | Ultra-low IQ, identical | Ultra-low IQ, fixed rail | Ultra-low noise, high current |
Ключевые отличия
- Industry-low 5 uA quiescent current (против TPS7A4901DGNR)
- 60 V input tolerance (против TPS7A4901DGNR)
- Automotive drop-in upgrade path (против TPS7A1601QDGNRQ1)
Заметки по проектированию
At 24 V input, 3.3 V output, and 100 mA load, the TPS7A1601DGNR dissipates about 2.1 W. Bond the HVSSOP-8 exposed pad to a generous ground copper area (at least 1 square inch with thermal vias) per TI datasheet thermal layout guidance. At lighter loads, dissipation scales linearly, but always compute worst-case continuous dissipation against the package theta-JA before finalizing the layout.
Place a 2.2 uF or larger ceramic output capacitor within a few millimeters of the OUT pin and an input capacitor close to IN. Connect the exposed pad directly to the ground plane with an array of vias for both electrical return and heat spreading. Route the FB divider with short traces away from the PG and switching-node nets to preserve output accuracy.
Never exceed the 60 V absolute maximum input, including transients - the 60 V rating is the family's key advantage, but surges above it will damage the device. Do not omit the DELAY capacitor if PG timing matters; the programmable delay must be matched to the MCU reset requirement. The PG output is open-drain, so it needs an external pull-up that may be to any rail up to 60 V.
Информация о соответствии
RoHS compliant per distributor listing for standard DGNR. AEC-Q100 qualification applies to the TPS7A1601QDGNRQ1 variant, not this standard part.
