TS331ILT - 1.6V-5V Micropower Open-Drain Comparator | STMicroelectronics
Артикул: TS331ILT ✓ АктивенTS331ILT Обзор
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input exceeds the other by more than its input-offset threshold. The TS331 belongs to the comparator, analog IC, and low-voltage power-management hierarchy. It uses an open-drain output, allowing the output to be pulled up externally when a wired-OR arrangement, level translation, or direct digital-interface connection is required.
The TS331ILT operates from 1.6V to 5V and provides rail-to-rail inputs, allowing signals to be compared close to the supply rails without relying on a conventional mid-supply input range. The listed specifications include 26 uA supply current, 1 nA input bias current, 40 nA input offset current, 5 mV input offset voltage, 4.5 uV/°C temperature drift, 720 ns propagation delay, and 79 dB channel-to-channel rejection. These characteristics balance response speed, low power, and precision for compact embedded systems.
The open-drain output is useful when several signals must be combined, but it requires an external pull-up resistor in most applications. The SOT-23-5 footprint supports dense PCB layouts, although correct input polarity and output-pull-up placement are important. The comparator can be used for voltage-threshold detection, battery monitoring, sensor signal conditioning, overvoltage detection, and portable equipment.
Designers should select pull-up voltage and resistor values carefully, account for the open-drain output's rise time, and verify operation across the full temperature range. The TS331 family's low supply current and rail-to-rail inputs are particularly advantageous in 1.8V, 2.5V, and 3.3V systems where the signal range may span the full supply voltage.
This product page combines the manufacturer specifications, package information, practical design guidance, and drop-in replacement considerations for engineers evaluating the TS331ILT in low-voltage comparator applications.
Аналоги без доработки для TS331ILT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TS331ILT (тот же форм-фактор и посадочное место) — отличается по Comparator Type, Input Common-Mode Range, Operating Temperature Range, Output Type, Package.
TS331IYLT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TS331CX5 RFG
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TS331ILT Максимальные параметры и электрические характеристики
| Comparator Type | Single-channel general-purpose comparator |
| Тип выхода | Open-drain |
| Supply Voltage Range | 1.6 V to 5 V |
| Typical Supply Current | 20 uA |
| Listed Supply Current | 26 uA |
| Input Bias Current | 1 nA |
| Input Offset Current | 40 nA |
| Input Offset Voltage | 5 mV |
| Input Voltage Drift | 4.5 uV/°C |
| Propagation Delay | 720 ns |
| Channel-to-Channel Rejection | 79 dB |
| Input Common-Mode Range | Rail-to-rail |
| Диапазон рабочих температур | -40 °C to +125 °C |
| Корпус | SOT-23-5 |
| Тип монтажа | Surface mount |
| Количество выводов | 5 pins |
| Статус RoHS | Compliant |
Руководство по цоколевке TS331ILT в корпусе sot-23-5
Цоколевка для TS331ILT (корпус sot-23-5). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для TS331ILT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TS331ILT подходит для 6 применениеs: Battery Voltage Threshold Detection, Portable Sensor Signal Conditioning, Overvoltage Protection, Low-Voltage Logic Interface, Battery Charger Status Detection, Industrial Limit Detection.
Battery Voltage Threshold Detection
The TS331ILT fits low-voltage battery systems because it operates from 1.6V to 5V and has typical current consumption as low as 20 uA. Place the comparator between a divided battery-voltage signal and a precision reference to detect an undervoltage or overvoltage condition. Rail-to-rail inputs are useful when the monitored signal spans much of the battery's operating range, while the open-drain output can be pulled up to the logic rail used by a supervisor or microcontroller. For a battery-powered product, choose the pull-up value to avoid excessive static current while maintaining an acceptable output rise time.
Рекомендуется
Portable Sensor Signal Conditioning
The TS331ILT is appropriate for comparing a sensor output against a threshold in a compact, energy-limited device. Its 1 nA input bias current and 40 nA input offset current help reduce errors when the source impedance is relatively high, while the 1.6V minimum supply supports low-voltage sensor platforms. The rail-to-rail input range allows the comparator to monitor signals near either supply rail. The open-drain output is useful when the sensor alarm must be wired to a system input or combined with another fault signal through a pull-up resistor.
Рекомендуется
Overvoltage Protection
The TS331ILT can implement a compact overvoltage detector by comparing a divided supply signal with a reference voltage. Its 720 ns propagation delay is short enough for many power-management monitoring paths, and the open-drain output allows a fault signal to be pulled up to the system logic level. The comparator's 1.6V to 5V operating range supports low-voltage rails commonly found in portable and embedded systems. Confirm the input absolute maximum ratings, output pull-up arrangement, and system response requirements in the manufacturer datasheet before using the device as a primary protection element.
Рекомендуется
Low-Voltage Logic Interface
The TS331ILT is useful for translating a low-voltage analog decision into an open-drain digital indication. Its rail-to-rail inputs can compare signals supplied by 1.8V, 2.5V, or 3.3V systems, and the open-drain output gives the designer control over the pull-up voltage. This is helpful for open-drain buses, interrupt lines, and fault flags where multiple outputs need to share a node. Because the output only actively pulls low, the external pull-up resistor determines both the high level and the RC rise time, so the PCB layout should keep the pull-up close to the relevant load.
Рекомендуется
Battery Charger Status Detection
The TS331ILT can monitor charger or power-path signals in a portable system by comparing a scaled voltage with a reference. Its micropower operation supports designs where the comparator remains active during long idle periods, and the 5-pin SOT-23-5 package conserves board area in wearables, portable instruments, and small embedded controllers. The rail-to-rail inputs make the device suitable for low-rail sensing, while the open-drain output can be connected to a charger-status or power-management signal. Verify the exact input polarity and pull-up voltage against the circuit schematic during layout review.
Рекомендуется
Industrial Limit Detection
The TS331ILT can monitor a scaled process or supply signal against a threshold in compact industrial control electronics. Its 1.6V to 5V supply operation and rail-to-rail inputs support low-voltage sensing nodes, while the 5 mV offset-voltage specification helps establish a defined decision boundary. The open-drain output supports fail-safe wiring when an alert must remain low during a reset or power-loss condition. The SOT-23-5 package is suitable for dense analog and mixed-signal boards, but production designs should verify the operating temperature range, input limits, and external pull-up network.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TS331ILT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TS331IYLT | TS331CX5 RFG |
|---|---|---|---|
| Package | SOT-23-5 | SOT-23-5 | SOT-23-5 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Comparator Type | Single-channel general-purpose comparator | Single-channel general-purpose comparator | Single-channel comparator |
| Output Type | Open-drain | Open-drain | Open-drain |
Ключевые отличия
- Micropower operation for portable threshold detection (против TS331IYLT)
- Rail-to-rail input operation in a low-voltage package (против TS331CX5 RFG)
- Defined low-power threshold performance (против TS331IYLT)
Заметки по проектированию
The TS331ILT is specified for a 1.6V to 5V supply and typical current consumption as low as 20 uA. In a battery design, include the comparator's supply current, input bias current of 1 nA, and the current drawn by the external open-drain pull-up when the output is high. A pull-up tied to a higher logic rail can dominate the standby budget, so choose its resistance and switching strategy together with the battery load.
Place the TS331ILT close to the sensed signal and the external pull-up resistor to minimize trace capacitance and sensitivity to coupling. Keep the pull-up return path short and connect the comparator ground pin to the quiet analog ground reference used by the signal source. Because the device is rail-to-rail, input traces should be kept away from switching nodes and clock edges. Verify the final SOT-23-5 land pattern against the manufacturer package drawing.
The open-drain output does not drive a defined high level by itself; omitting the pull-up resistor can leave the output floating and cause undefined digital behavior. Also do not assume that the TS331IYLT and TS331CX5 RFG are automatically equivalent based on package similarity. Confirm input polarity, offset, propagation delay, temperature grade, and qualification against the manufacturer datasheet before approving a drop-in replacement.
Информация о соответствии
The product listing identifies the TS331ILT as RoHS compliant. The supplied manufacturer and distributor information does not establish the REACH, lead-free, halogen-free, or conflict-minerals status for this exact ordering code.