TSA1203IF - Dual 12-bit 40MSPS ADC | STMicroelectronics
Артикул: TSA1203IF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.85 | $14,85 |
| 10 | $13.42 | $134,20 |
| 100 | $11.78 | $1.178,00 |
| 500 | $10.36 | $5.180,00 |
| 1.000 | $9.12 | $9.120,00 |
| 2.500 | $8.2 | $20.500,00 |
TSA1203IF Обзор
An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts a continuous-time, continuous-amplitude analog input into a discrete-time, discrete-amplitude digital code. Pipeline ADCs such as the TSA1203IF use a multi-stage switched-capacitor architecture to achieve high sampling rates while keeping per-stage power and die area modest, sitting within the broader hierarchy of data converters -> ADC -> high-speed pipeline ADC -> semiconductor. Dual-channel variants like this one are favored for diversity receivers, I/Q baseband sampling, and simultaneous multi-antenna digital beamforming because the two channels are sampled on a common clock edge, eliminating channel-to-channel skew.
Key features include 1 GHz analog input bandwidth, SFDR of -68.3 dBc at 10 MHz input, multiplexed outputs for reduced pin count, common clocking between channels, and pin-to-pin compatibility with the dual 10-bit 20/40 MSPS TSA1005-20/40 and the dual 12-bit 20 MSPS TSA1204. The pipelined architecture combined with digital error correction yields clean 12-bit outputs at full clock rate without requiring complex external calibration at room temperature.
Typical applications include cellular base station receivers, IF sampling for software-defined radio, medical imaging front-ends, and industrial ultrasound beamformers. The integrated reference and dual independent input channels also suit multi-channel data-acquisition cards for test and measurement instrumentation. When designing with this part, ensure the analog and digital grounds are joined only at a single point near the exposed pad, and that the analog supply is decoupled with both 0.1 µF ceramic and 10 µF bulk capacitance within 5 mm of the supply pins.
Аналоги без доработки для TSA1203IF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TSA1203IFT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TSA1204
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TSA1005-40
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TSA1005-20
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TSA1203IF-E
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TSA1203IF Максимальные параметры и электрические характеристики
| Manufacturer | STMicroelectronics |
| Part Number | TSA1203IF |
| Разрешение | 12 bit |
| Number of Channels | 2 (dual, simultaneous sampling) |
| Частота дискретизации | 40 MSPS (max) |
| Architecture | Pipelined, with digital error correction |
| Analog Input Bandwidth | 1 GHz |
| Supply Voltage (Analog) | 2.5 V single supply |
| Supply Voltage (Digital Output) | 2.5 V or 3.3 V (independent) |
| Power Consumption | 230 mW at 40 Msps |
| SFDR | -68.3 dBc at Fin = 10 MHz |
| Output Interface | CMOS, multiplexed between channels |
| Опорное напряжение | Built-in (internal) |
| Track-and-Hold | Dual simultaneous sample-and-hold inputs |
| Корпус | 48-pin TQFP (7x7 mm) |
| Диапазон рабочих температур | -40 °C to +85 °C (industrial) |
| Process Technology | 0.25 µm CMOS |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов TSA1203IF
| Контакт 1 | AIN1A — Analog input channel 1, positive |
| Контакт 2 | AIN1B — Analog input channel 1, negative (complementary) |
| Контакт 3 | VREF — Internal reference voltage decoupling |
| Контакт 4 | AGND — Analog ground |
| Контакт 5 | AVDD — Analog supply, 2.5 V |
| Контакт 6 | AGND — Analog ground |
| Контакт 7 | CLK — Common clock input for both channels |
| Контакт 8 | CLKB — Complementary clock input |
| Контакт 9 | AGND — Analog ground |
| Контакт 10 | AVDD — Analog supply, 2.5 V |
| Контакт 11 | AGND — Analog ground |
| Контакт 12 | AIN2A — Analog input channel 2, positive |
| Контакт 13 | AIN2B — Analog input channel 2, negative (complementary) |
| Контакт 14 | AGND — Analog ground |
| Контакт 15 | AVDD — Analog supply, 2.5 V |
| Контакт 16 | AVDD — Analog supply, 2.5 V |
| Контакт 17 | AGND — Analog ground |
| Контакт 18 | AVDD — Analog supply, 2.5 V |
| Контакт 19 | AGND — Analog ground |
| Контакт 20 | AVDD — Analog supply, 2.5 V |
| Контакт 21 | DVDD — Digital output supply, 2.5 V or 3.3 V |
| Контакт 22 | DGND — Digital ground |
| Контакт 23 | D11A — Channel 1 output bit 11 (MSB) when MUX selects ch1 |
| Контакт 24 | D10A — Channel 1 output bit 10 when MUX selects ch1 |
| Контакт 25 | D9A — Channel 1 output bit 9 when MUX selects ch1 |
| Контакт 26 | D8A — Channel 1 output bit 8 when MUX selects ch1 |
| Контакт 27 | D7A — Channel 1 output bit 7 when MUX selects ch1 |
| Контакт 28 | D6A — Channel 1 output bit 6 when MUX selects ch1 |
| Контакт 29 | D5A — Channel 1 output bit 5 when MUX selects ch1 |
| Контакт 30 | D4A — Channel 1 output bit 4 when MUX selects ch1 |
| Контакт 31 | D3A — Channel 1 output bit 3 when MUX selects ch1 |
| Контакт 32 | D2A — Channel 1 output bit 2 when MUX selects ch1 |
| Контакт 33 | D1A — Channel 1 output bit 1 when MUX selects ch1 |
| Контакт 34 | D0A — Channel 1 output bit 0 (LSB) when MUX selects ch1 |
| Контакт 35 | D11B — Channel 2 output bit 11 (MSB) when MUX selects ch2 |
| Контакт 36 | D10B — Channel 2 output bit 10 when MUX selects ch2 |
| Контакт 37 | D9B — Channel 2 output bit 9 when MUX selects ch2 |
| Контакт 38 | D8B — Channel 2 output bit 8 when MUX selects ch2 |
| Контакт 39 | D7B — Channel 2 output bit 7 when MUX selects ch2 |
| Контакт 40 | D6B — Channel 2 output bit 6 when MUX selects ch2 |
| Контакт 41 | D5B — Channel 2 output bit 5 when MUX selects ch2 |
| Контакт 42 | D4B — Channel 2 output bit 4 when MUX selects ch2 |
| Контакт 43 | D3B — Channel 2 output bit 3 when MUX selects ch2 |
| Контакт 44 | D2B — Channel 2 output bit 2 when MUX selects ch2 |
| Контакт 45 | D1B — Channel 2 output bit 1 when MUX selects ch2 |
| Контакт 46 | D0B — Channel 2 output bit 0 (LSB) when MUX selects ch2 |
| Контакт 47 | MUX — Channel select for multiplexed output bus |
| Контакт 48 | EP — Exposed thermal pad - tie to AGND for heat dissipation |
Типичное применение
TSA1203IF подходит для 6 применениеs: Cellular Base Station I/Q Baseband Sampling, IF Sampling for Software-Defined Radio, Medical Ultrasound Beamforming Front-End, Industrial Multi-Channel Data Acquisition, Communications Test and Measurement, Radar and Lidar Signal Processing.
Cellular Base Station I/Q Baseband Sampling
The TSA1203IF's dual simultaneous sample-and-hold inputs and common clocking make it well matched to I/Q baseband sampling in cellular base station receivers. With 12-bit resolution and 40 MSPS per channel, the ADC cleanly captures multi-carrier GSM, EDGE and WCDMA signals at baseband without inter-channel skew. The independent 2.5 V or 3.3 V digital output supply interfaces directly to FPGA baseband logic, eliminating level shifters in the signal chain. Spurious-free dynamic range of -68.3 dBc at 10 MHz input keeps harmonic spurs well below the fundamental, supporting tight EVM budgets required by 3GPP.
Рекомендуется
IF Sampling for Software-Defined Radio
The TSA1203IF's 1 GHz analog input bandwidth enables direct IF sampling of intermediate-frequency signals in software-defined radio (SDR) architectures, removing one or more analog mixer stages from the receive chain. Sampling at 40 MSPS gives sufficient Nyquist headroom for signals at 15-20 MHz IF while keeping the digital data rate manageable for downstream FPGA or DSP processing. The 230 mW power dissipation at full sample rate is low for the speed class, simplifying thermal design in portable and manpack SDR form factors. The built-in internal reference removes a noisy external reference from the BOM.
Рекомендуется
Medical Ultrasound Beamforming Front-End
Dual-channel simultaneous sampling at 40 MSPS makes the TSA1203IF well suited to multi-channel ultrasound receiver arrays, where channel-to-channel timing skew must be held below a few hundred picoseconds for accurate beamforming. Each channel can digitize the output of an LNA plus TGC stage without time-alignment errors, preserving phase coherence across the 32-, 64- or 128-element probe. The 12-bit dynamic range supports typical ultrasound penetration at 5-10 MHz center frequency. Low 230 mW per dual channel keeps total power manageable for portable cart-based ultrasound systems.
Рекомендуется
Industrial Multi-Channel Data Acquisition
In industrial data-acquisition cards and modular instrumentation, the TSA1203IF packs two simultaneous 12-bit, 40 MSPS converters into a single TQFP-48 footprint, doubling channel density on the PCB. Multiplexed outputs reduce digital pin count and free board space for additional channels, isolation barriers, or trigger logic. The -40 to +85 °C industrial operating range covers most factory-floor and outdoor enclosure environments. The CMOS output stage can be powered from 3.3 V to interface directly to modern FPGA-based acquisition controllers.
Рекомендуется
Communications Test and Measurement
Vector signal analyzers, arbitrary waveform digitizers, and cable modem test equipment benefit from the TSA1203IF's 1 GHz analog bandwidth and -68.3 dBc SFDR. The dual-channel capability allows simultaneous capture of I and Q, or of two DUT outputs for differential measurements, in a single device. Independent AVDD/DVDD rails simplify board layout by separating analog and digital return currents. The internal reference reduces calibration drift compared with an external reference IC.
Рекомендуется
Radar and Lidar Signal Processing
Short-range automotive radar and industrial lidar pre-processors benefit from the TSA1203IF's 1 GHz analog bandwidth, which lets the ADC sample wideband IF signals directly without an analog downconversion stage. Dual-channel sampling captures matched I/Q pairs from a single mixer, simplifying DSP demodulation downstream. With 12-bit resolution, range and velocity resolution are sufficient for parking-assist and perimeter-security radar systems. The TQFP-48 footprint is footprint-compatible with the TSA1204 (20 MSPS) and TSA1005-40 (10-bit) family, easing platform scalability.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TSA1203IF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TSA1203IFT | TSA1204 | TSA1005-40 | TSA1005-20 | TSA1203IF-E |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | TQFP-48 (7x7 mm) | TQFP-48 (7x7 mm) - same | TQFP-48 (7x7 mm) - same | TQFP-48 (7x7 mm) - same | TQFP-48 (7x7 mm) - same | TQFP-48 (7x7 mm) - same |
| Resolution | 12 bit | 12 bit | 12 bit | 10 bit | 10 bit | 12 bit |
| Number of Channels | 2 (dual, simultaneous) | 2 (dual, simultaneous) | 2 (dual, simultaneous) | 2 (dual, simultaneous) | 2 (dual, simultaneous) | 2 (dual, simultaneous) |
| Max Sampling Rate | 40 MSPS | 40 MSPS | 20 MSPS | 40 MSPS | 20 MSPS | 40 MSPS |
| Supply Voltage (Analog) | 2.5 V | 2.5 V | 2.5 V | 2.5 V | 2.5 V | 2.5 V |
| Pin-to-Pin Compatible | Reference (TQFP-48) | Yes (identical silicon, different packaging) | Yes (lower speed, same pinout) | Yes (lower resolution, same pinout) | Yes (lower resolution and speed, same pinout) | Yes (extended/screened variant, same pinout) |
Ключевые отличия
- Pin-to-pin compatible across four STMicroelectronics family members for design scalability (против TSA1204, TSA1005-40, TSA1005-20)
- Dual simultaneous sample-and-hold with 1 GHz analog bandwidth enables direct IF sampling (против Generic single-channel 12-bit 40 MSPS ADCs)
- Independent 2.5 V or 3.3 V CMOS output supply simplifies FPGA interfacing (против ADCs with single fixed output supply)
Заметки по проектированию
The TSA1203IF requires a clean 2.5 V analog supply (AVDD) and an independent 2.5 V or 3.3 V digital output supply (DVDD). Place a 0.1 µF ceramic decoupling capacitor within 5 mm of each AVDD pin and add a 10 µF bulk tantalum or ceramic capacitor at the supply entry point. Tie analog and digital grounds at a single point near the exposed pad to avoid ground-loop noise coupling into the analog front-end. Per ST datasheet CD00002389, separate AVDD/DVDD regulation prevents digital switching noise from corrupting the analog sampling path.
Estimated: with theta_JA of approximately 50 C/W for the TQFP-48 (7x7) package on a 4-layer JEDEC test board and 230 mW dissipation, the junction temperature rise above ambient is roughly 11.5 C, leaving ample margin under the 125 C maximum for the -40 to +85 C industrial range. However, on smaller 2-layer boards with poor copper pour, theta_JA can exceed 80 C/W, so always stitch the exposed pad with multiple vias to a continuous analog ground pour to keep junction temperature in spec at elevated ambient.
Route the CLK input with a 50-100 ohm transmission line, kept short and surrounded by analog ground on both sides, to preserve the clock edge and minimise jitter. Keep the analog input traces matched in length and impedance to within 0.5 mm so that channel-to-channel skew remains below the datasheet limit. Shield the high-speed digital data bus (D0A-D11A, D0B-D11B) from the analog inputs with a ground pour and avoid routing digital traces directly over the analog input region of the package.
Do not omit the decoupling capacitor on the VREF pin - it is critical for low reference noise and stable SFDR. Driving the analog inputs beyond the 1 Vpp differential range or with improper common-mode bias causes severe distortion and will degrade SFDR well below the -68 dBc typical figure. Finally, the MUX pin must be clocked at half the ADC sample rate to interleave the two channels correctly; failing to drive MUX results in both channels outputting on the same data bus at the same time, corrupting downstream logic.
Информация о соответствии
RoHS and lead-free compliance confirmed per STMicroelectronics product page (st.com). Industrial -40 to +85 C operating range only; the TSA1203IF is not AEC-Q100 automotive qualified - use the -E variant for extended-temperature applications.