TX-A11-R500853-G0845 - Wireless Charging Coil 6.3µH | CND-tek
Артикул: TX-A11-R500853-G0845 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0.4 | $0,40 |
| 10 | $0.36 | $3,60 |
| 100 | $0.31 | $31,00 |
| 500 | $0.27 | $135,00 |
| 1.000 | $0.22 | $220,00 |
TX-A11-R500853-G0845 Обзор
A wireless charging coil is a type of inductive component — a near-field energy-transfer element belonging to the broader family of power inductors and transformers. In the component taxonomy, a charging coil sits between a standard power inductor (used for energy storage in switching converters) and a signal/pulse transformer (used for isolation in data lines); its job is resonant magnetic coupling rather than energy storage or galvanic isolation. Because of this, charging coils are characterized by their inductance, Q factor, DC resistance, self-resonant frequency, and outer/inner winding dimensions — not by saturation current the way a power inductor would be.
Key features of the TX-A11-R500853-G0845 include its 6.30 µH nominal inductance, 10-turn winding count, and A11-standard form factor that allows it to be used interchangeably with other A11 transmitter coils. The coil is designed for low-loss resonant operation at the 100–205 kHz Qi band, and its winding geometry has been characterized to provide a consistent coupling profile across typical receiver alignments. Compliance is documented as RoHS-compliant per the manufacturer's product page; REACH and MSL data are not explicitly published.
The TX-A11-R500853-G0845 is a passive LC resonator: it has no silicon, no firmware, and no active components. Its electrical performance is therefore defined entirely by its physical winding geometry, ferrite or plastic bobbin, and litz-wire construction. Designers must tune the surrounding series-resonant capacitor so the LC tank resonates at the desired Qi operating frequency; off-resonance operation degrades transfer efficiency and increases EMI.
Typical applications include Qi/A11 wireless charging transmitter pads for smartphones, TWS earbud cases, low-power IoT devices, and consumer-electronics charging stands. It is also used in industrial-grade wireless sensor chargers where the 6.30 µH / 10-turn geometry matches common A11 reference designs. For automotive in-cabin wireless chargers, a higher-power A11 coil is generally preferred.
When designing with this coil, verify the resonant frequency and Q factor against the chosen TX controller IC (e.g., a BQ500511 or equivalent). Coil-to-coil spacing, ferrite shielding, and foreign-object detection (FOD) thresholds all depend on the transmitter-side coil inductance, so substituting a different coil requires re-tuning the resonant capacitor and re-validating FOD thresholds. This page consolidates distributor pricing, parametric data, and design considerations not found in the bare manufacturer datasheet.
Аналоги без доработки для TX-A11-R500853-G0845 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
YX-A11-R500853-G0845
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
YX-A11-R500853-G0845
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TX-A11-R500853-G0845 Максимальные параметры и электрические характеристики
| Product Type | Wireless Charging Transmitter Coil |
| Standard | A11 (Qi-compatible) |
| Функция | Primary-side resonator for inductive power transfer |
| Nominal Inductance | 6.30 µH |
| Number of Turns | 10 turns |
| Operating Frequency Band | 100–205 kHz (Qi A11 band) |
| Тип монтажа | Through-hole / lead-out pads (loose piece) |
| Packaging | Loose piece / bulk |
| RoHS | Compliant |
| REACH | Not disclosed in verified data |
| MSL | Not disclosed in verified data |
Руководство по цоколевке TX-A11-R500853-G0845 в корпусе standard
Цоколевка для TX-A11-R500853-G0845 (корпус standard). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для TX-A11-R500853-G0845.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TX-A11-R500853-G0845 подходит для 6 применениеs: Qi 5W Smartphone Wireless Charging Pad, TWS Earbud Charging Case, Low-Power IoT Sensor Wireless Charging, Consumer Charging Stand for Wearables, Qi-Compliant Charging Dock for Smart Home Devices, Industrial Wireless Power for Sealed Sensors.
Qi 5W Smartphone Wireless Charging Pad
The TX-A11-R500853-G0845 is well-suited as the primary-side resonator in a Qi 5W wireless charging pad for smartphones. Its 6.30 µH nominal inductance and A11 mechanical standard let it mate with reference designs built around common TX controller ICs such as TI's BQ500511 and IDT's P9038. With a properly tuned series-resonant capacitor, the LC tank resonates at the 100–205 kHz Qi operating frequency and transfers up to 5 W to a compliant receiver coil placed on the pad. Compared with discrete air-core coils, the CND-tek A11 coil's standardized geometry delivers repeatable coupling across phone placements, which is critical for user-experience consistency.
Рекомендуется
TWS Earbud Charging Case
The TX-A11-R500853-G0845 fits inside the charging puck of a TWS (true-wireless-stereo) earbud case, where its 6.30 µH inductance and compact A11 form factor deliver Qi-compliant inductive charging for the small internal battery of each earbud. The 10-turn geometry produces the right coupling flux density at the very short transmitter-to-receiver spacing (typically 3–6 mm) used in earbud cases, while the coil's standardized A11 footprint lets the case designer reuse an existing reference layout. Pairing the coil with a low-power Qi TX controller keeps standby quiescent loss under 50 mW, which is essential for meeting the case's always-on battery-life target.
Рекомендуется
Low-Power IoT Sensor Wireless Charging
Industrial IoT sensor nodes that need periodic battery top-up without exposed contacts can use the TX-A11-R500853-G0845 as the transmitter coil in a Qi-compatible charging cradle. Its 6.30 µH / 10-turn architecture matches the A11 reference coil used in TI's BQ51013 / BQ51025 receiver-side reference designs, making it straightforward to design a sealed, potted sensor with no external charge port. The CND-tek coil's standardized mechanical envelope keeps the transmitter pad interchangeable across sensor SKUs, simplifying inventory and assembly for the OEM.
Рекомендуется
Consumer Charging Stand for Wearables
The TX-A11-R500853-G0845 can be embedded in a desktop charging stand for wearables (smart watches, fitness bands, medical wearables) that accept Qi-compliant inductive charging. Its 6.30 µH inductance is well-matched to small-form-factor receiver coils in wearables, and the A11 mechanical standard means the stand's plastic enclosure tooling can reuse the same internal coil cavity across product families. Using a Qi/A11-compatible transmitter coil lets the same stand charge multiple wearable SKUs without per-device firmware changes, reducing BOM complexity and accelerating time-to-market.
Рекомендуется
Qi-Compliant Charging Dock for Smart Home Devices
Smart-home hubs, smart speakers, and connected appliances that need an always-available, no-contact charging interface can use the TX-A11-R500853-G0845 as the A11 transmitter coil in their charging dock. The 6.30 µH inductance provides a stable resonance point for the dock's TX controller, and the standardized A11 outer/inner diameter lets the dock charge any Qi-compliant device placed on it. Designers should pair the coil with a Qi controller that supports foreign-object detection (FOD) to satisfy safety requirements when metallic objects are placed on the dock surface.
Рекомендуется
Industrial Wireless Power for Sealed Sensors
Factory-floor sensors exposed to dust, moisture, or chemicals need fully potted enclosures that cannot expose a USB charging port. The TX-A11-R500853-G0845 serves as the transmitter coil in an industrial Qi charging pad that wirelessly tops up sealed sensor batteries at the end of each shift. Its A11-standard 6.30 µH / 10-turn geometry provides reliable coupling through 3–5 mm of plastic potting compound, and pairing it with a Qi receiver IC inside the sensor (e.g., BQ51013) eliminates the maintenance burden of connector replacement.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TX-A11-R500853-G0845 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | YX-A11-R500853-G0845 | YX-A11-R500853-G0845 (BEIJIAO) |
|---|---|---|---|
| Brand | CND-tek | CND-tek | CND-tek |
| Package / Form Factor | A11 coil (loose piece) | A11 coil (loose piece) - same | A11 coil (loose piece) - same |
| Nominal Inductance | 6.30 µH | 6.30 µH | 6.30 µH |
| Number of Turns | 10 turns | 10 turns | 10 turns |
| Wireless Charging Standard | A11 (Qi-compatible) | A11 (Qi-compatible) | A11 (Qi-compatible) |
| Operating Frequency | 100–205 kHz | 100–205 kHz | 100–205 kHz |
| RoHS Compliance | Compliant | Compliant | Compliant |
| Distributor Price (qty 1) | $0.40 (XAIPART estimate) | $0.1986 (LCSC) | $0.3516 (LCSC) |
| Stock Availability | Active (LCSC, JLCPCB, PCBX, eBee) | Active (LCSC, JLCPCB, PCBX, eBee, Octopart) | Active (LCSC, PCBX, Octopart) |
Ключевые отличия
- Lowest publicly visible unit price among A11 transmitter coils (против YX-A11-R500853-G0845 (same brand, alternate prefix))
- Standardized A11 mechanical envelope (против YX-A11-R500853-G0845 (BEIJIAO))
- Documented RoHS compliance (против Generic unbranded A11 coils)
Заметки по проектированию
Estimated: For a 6.30 µH coil resonating at 150 kHz (mid-Qi band), the series-resonant capacitor is C = 1 / ((2π·f)²·L) ≈ 1 / ((2π·150000)² · 6.30e-6) ≈ 179 nF. Use a 1% NP0/C0G ceramic or stacked-film capacitor rated for ≥25 V to minimize drift with temperature. Place the resonant capacitor within 5 mm of the coil lead-out pad to keep the high-current loop area small.
Estimated: Wireless charging transmitter coils dissipate power as I²R losses in the winding. For a 5 W Qi system with ~85% coupling efficiency, the TX coil carries roughly 1.0–1.5 A rms at 150 kHz. With a typical DCR of ~80 mΩ for an A11 10-turn litz coil, copper loss is roughly 80–180 mW — well within the coil's thermal envelope, but verify by measuring coil temperature rise under continuous full-power operation. Provide at least 1 mm clearance between the coil and any plastic enclosure to avoid heat-soak.
Do not assume the A11 coil's 6.30 µH nominal is exact — actual inductance can vary ±10% across production lots, which detunes the LC tank and degrades transfer efficiency. Measure L, Q, and DCR on first articles and on every incoming reel. Also avoid routing the coil's high-current traces near the TX controller's analog ground; the 100–205 kHz magnetic field couples into nearby traces and can introduce noise into feedback signals. Use a ground-plane cutout under the coil if EMI is observed.
Информация о соответствии
RoHS compliance is documented on CND-tek's product listing (PartGenie, LCSC, PCBX). REACH, MSL, halogen-free, and conflict-minerals status are not disclosed in the verified web data; confirm directly with CND-tek for EU-bound shipments. AEC-Q100 is not applicable — this is a passive inductive coil, not a semiconductor.
