VNH7100BASTR - 12A Automotive H-Bridge Motor Driver | STMicroelectronics
Артикул: VNH7100BASTR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.4777 | $4,48 |
| 10 | $4.03 | $40,30 |
| 100 | $3.58 | $358,00 |
| 500 | $3.14 | $1.570,00 |
| 1.000 | $2.79 | $2.790,00 |
VNH7100BASTR Обзор
An H-bridge motor driver is a power management IC that controls the direction and speed of a brushed DC motor by selectively activating four switches in an H configuration. It belongs to the broader hierarchy of motor drivers -> motion controllers -> power management ICs -> semiconductors. The VNH7100BASTR integrates the full H-bridge and the gate-drive/protection logic in one package, eliminating the bulk of discrete MOSFET bridges, gate drivers, and current-sense amplifiers.
Key features include a 60 mΩ typ. on-resistance per high-side switch that minimizes conduction loss, PWM control up to 20 kHz for precise speed regulation, and a comprehensive protection suite: undervoltage lockout, overvoltage clamp, thermal shutdown with auto-restart, and load current limitation. A dedicated diagnostic feedback pin reports fault conditions to the host MCU. The PowerSSO-16 exposed pad provides a low thermal resistance path, supporting 12 A continuous operation with proper PCB copper.
Typical applications include 12 V automotive brushed DC loads such as power window lifters, seat adjusters, mirror fold actuators, HVAC flaps, and door lock motors. The wide 4 V to 28 V supply range also suits industrial 24 V brush DC drives and battery-powered robotics where a single-IC H-bridge simplifies BOM and PCB area.
When designing with this device, dedicate at least 1 sq in of top-side copper to the exposed pad and stitch a 4×4 thermal via array to the inner/inner-outer copper planes to keep junction temperature in spec. Place a 100 nF X7R ceramic bypass within 2 mm of the VCC pin and a bulk 47 µF electrolytic at the motor connector. Use a gate resistor or RC snubber on the PWM input if long MCU traces cause ringing above 5 MHz.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, giving engineers a single decision-ready resource for selecting and implementing the VNH7100BASTR in automotive and industrial brushed DC motor designs.
Аналоги без доработки для VNH7100BASTR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с VNH7100BASTR (тот же форм-фактор и посадочное место) — отличается по Continuous Output Current, Package, Technology, Function, Protection Features.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
VNH7070BASTR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
VNH7100ASTR
✅ Прямая замена✓ В наличии
$2.58 / шт.
Открыть даташит →VNH7100BAS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
VNH7100BASTR Максимальные параметры и электрические характеристики
| Функция | Fully integrated H-bridge motor driver |
| Топология | Full H-bridge with dual high-side + dual low-side MOSFETs |
| Supply Voltage Range | 4 V to 28 V |
| Continuous Output Current | 12 A |
| On-Resistance per High-Side Switch (typ.) | 60 mΩ |
| PWM Switching Frequency | Up to 20 kHz |
| Technology | VIPower M0 (smart-power) |
| Диапазон рабочих температур | -40 °C to +150 °C (junction) |
| Корпус | PowerSSO-16 (SO-16N with exposed pad) |
| Тип монтажа | Surface Mount |
| Количество выходов | 1 (H-bridge) |
| Automotive Qualification | AEC-Q100 qualified |
| Protection Features | UVLO, overvoltage clamp, thermal shutdown, current limit |
| Diagnostic Output | Yes (fault feedback pin) |
| Статус RoHS | Compliant |
Конфигурация выводов VNH7100BASTR
| Контакт 1 | VCC — Power supply (4 V to 28 V) |
| Контакт 2 | OUT1 — H-bridge output 1 to motor |
| Контакт 3 | OUT2 — H-bridge output 2 to motor |
| Контакт 4 | GND — Ground |
| Контакт 5 | DIAG — Diagnostic fault feedback output |
| Контакт 6 | PWM — PWM input for speed control |
| Контакт 7 | EN — Enable input (active high) |
| Контакт 8 | IN1 — Logic input for direction control |
| Контакт 9 | IN2 — Logic input for direction control |
| Контакт 10 | NC — Not connected (per datasheet) |
| Контакт 11 | NC — Not connected (per datasheet) |
| Контакт 12 | NC — Not connected (per datasheet) |
| Контакт 13 | GND — Ground |
| Контакт 14 | GND — Ground |
| Контакт 15 | GND — Ground |
| Контакт 16 | GND — Ground |
Область безопасной работы
Типичное применение
VNH7100BASTR подходит для 6 применениеs: Automotive Power Window Lifter, Power Seat Adjuster Motor Drive, Side Mirror Fold Actuator, HVAC Blend/Flap Actuator, Door Lock Motor Drive, Industrial 24 V Brushed DC Drive.
Automotive Power Window Lifter
The VNH7100BASTR's 12 A continuous rating directly supports window-lift motor stall currents, and its 4 V lower supply bound survives 12 V cold-crank events. AEC-Q100 qualification allows the part to ship in OEM door-module PCBs without requalification. Place the H-bridge between the 12 V battery rail and the window motor, and use the diagnostic pin to feed back fault status to the body-control MCU.
Рекомендуется
Power Seat Adjuster Motor Drive
Seat-position motors require bidirectional current up to ~10 A and PWM speed control for soft-start comfort positioning. The VNH7100BASTR's 20 kHz PWM capability and 60 mΩ high-side RDS(on) keep dissipation under 1 W per switch during typical seat travel. The exposed PowerSSO-16 pad dissipates waste heat into the seat-module chassis ground plane, eliminating an external heatsink.
Рекомендуется
Side Mirror Fold Actuator
Mirror-fold motors draw 2-4 A peak during the 1-2 second fold cycle, well within the VNH7100BASTR's 12 A envelope. The integrated overvoltage clamp protects the H-bridge from 24 V jump-start transients on the body harness. The device's diagnostic output signals fault conditions back to the BCM, enabling OBD-compliant fault logging for premium mirror modules.
Рекомендуется
HVAC Blend/Flap Actuator
HVAC flap motors operate at low duty cycle with 1-3 A average current, but require VDC+ regulators for continuous position hold. The VNH7100BASTR's PWM control and current-limit features make it suitable for stepping the flap through precise angles while reporting stall conditions. AEC-Q100 qualification matches the under-dash thermal environment of HVAC control modules.
Рекомендуется
Door Lock Motor Drive
Door-latch actuators need a short 10-15 A inrush pulse followed by ~2 A holding current. The VNH7100BASTR handles the inrush on its 12 A continuous rating with the current-limit circuit clamping stall events. The integrated thermal shutdown protects against prolonged stall conditions, and the PowerSSO-16 exposed pad dissipates the inrush energy without an external heatsink.
Рекомендуется
Industrial 24 V Brushed DC Drive
On a 24 V industrial bus, the VNH7100BASTR's 28 V upper supply bound provides margin against rectified 24 V transformer ripple. The VIPower M0 protection suite rejects inductive kickback when the motor commutates, eliminating external flyback diodes and shrinking the BOM. Industrial enclosures with 50 °C ambient are tolerated thanks to the -40 °C to +150 °C junction range.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для VNH7100BASTR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | VNH7070BASTR | VNH7100ASTR | VNH7100BAS |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | PowerSSO-16 | PowerSSO-16 - same | PowerSSO-16 - same | PowerSSO-16 - same |
| Continuous Output Current | 12 A | 10 A | 12 A | 12 A |
| Supply Voltage Range | 4 V to 28 V | 4 V to 28 V | 4 V to 28 V | 4 V to 28 V |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes |
| PWM Frequency | Up to 20 kHz | Up to 20 kHz | Up to 20 kHz | Up to 20 kHz |
| Diagnostic Output | Yes | Yes | Yes | Yes |
Ключевые отличия
- 12 A continuous rating in PowerSSO-16 exposed-pad package (против VNH7070BASTR)
- Latest 'B' silicon revision (против VNH7100ASTR)
- AEC-Q100 automotive qualification (против DRV8873HPWPR)
Заметки по проектированию
Estimated: at 12 V supply, 12 A continuous output with a stalled motor (100% duty), the VNH7100BASTR dissipates approximately 60 mΩ × 12 A × 2 switches ≈ 17 W. A PowerSSO-16 with a 4×4 thermal via array on a 1 sq in copper pour keeps theta_JA under 30 °C/W, holding Tj below 150 °C in 50 °C ambient. At lower duty cycles (e.g. seat travel <2 s), much smaller copper areas are adequate.
Place a 100 nF X7R ceramic bypass within 2 mm of the VCC pin to suppress the high-side driver switching transients. Add a 47 µF electrolytic bulk capacitor at the motor connector to absorb motor commutation energy. Stitch a 4×4 thermal via array (0.3 mm drill, 0.6 mm pad) under the exposed pad and tie the inner planes to a clean ground island for best power dissipation.
Do not float the EN pin - tie it to VCC through a 10 kΩ pull-up if unused, or to the MCU GPIO if controlled. Avoid routing the motor wires parallel to the PWM logic traces for more than 25 mm; keep at least 5 mm spacing or a ground guard trace to prevent dv/dt noise from coupling into the IN1/IN2 logic. Always observe the motor current rating versus the H-bridge 12 A continuous limit; peak inrush above 12 A will trigger the current-limit circuit and may stall the application.
Информация о соответствии
AEC-Q100 qualified per ST product family. RoHS compliant per distributor listings. Halogen-free status not explicitly confirmed in verified data.
