VSC7984XYF - 11.3 Gb/s EAM Driver | Microchip Technology
Артикул: VSC7984XYF ✓ АктивенVSC7984XYF Обзор
An electroabsorption modulator driver, or EAM driver, is an interface IC that converts high-speed electrical data into the differential drive signals required by an electroabsorption-modulated optical transmitter. It belongs to the optical communication interface hierarchy: EAM driver, interface IC, integrated circuit, and semiconductor. Its primary role is to preserve signal integrity while delivering sufficient modulation voltage and bias conditions to an external optical modulator.
Selectable data retiming is the central performance feature of the VSC7984XYF. Retiming can resynchronize the incoming data stream to an internal or associated clock, helping reduce jitter in systems where source-device timing and transmitter-chain alignment are imperfect. The output-bias, modulation-voltage, and duty-cycle controls allow the driver to be adjusted to the requirements of the optical modulator and its surrounding drive network.
The device also incorporates internal operational amplifiers and an on-chip voltage reference. These functions reduce the amount of external circuitry needed to establish stable modulation and bias conditions. Internal amplification can simplify the signal path, while the reference supports repeatable control of the driver's operating state. The clocked architecture remains sensitive to trace routing, supply integrity, and the quality of the high-speed differential connections.
Typical uses include 10 GbE optical modules, SONET/SDH transmit equipment, optical transport systems, and other 10.3125 Gb/s-class optical interfaces. The VSC7984XYF is most appropriate where an external electroabsorption modulator requires controlled bias, adjustable modulation drive, and selectable retiming. Its suitability in a specific design still depends on the complete modulator interface, target jitter margin, and required data-rate classification.
When laying out a circuit around the VSC7984XYF, keep the high-speed differential output paths short and impedance-controlled, provide clean return paths, and place decoupling and termination components close to their associated pins. Confirm the exact pin assignments, exposed-pad requirements, supply sequencing, and output-impedance settings in the manufacturer datasheet before release to manufacturing.
This page organizes the verified VSC7984XYF technical facts, sourcing information, application guidance, and design considerations into one engineering reference. It also distinguishes directly documented capabilities from package details and lifecycle information that must be confirmed before a new design is released.
Аналоги без доработки для VSC7984XYF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиVSC7984XYF Характеристики
| Product Type | Electroabsorption modulator driver |
| Device Classification | Clocked interface IC |
| Nominal Data Rate | 11.3 Gb/s |
| Documented Maximum Data Rate | 12.5 Gb/s |
| Primary Optical Standard | SONET/SDH |
| Ethernet Application | 10 GbE |
| Data Retiming | Selectable |
| Output Bias Control | Adjustable output bias voltage |
| Modulation Control | Adjustable modulation voltage |
| Duty-Cycle Control | Adjustable duty cycle |
| Internal Amplification | Internal operational amplifiers |
| Voltage Reference | On-chip voltage reference |
| Package Family | QFN |
| Тип монтажа | Surface mount |
Руководство по цоколевке VSC7984XYF в корпусе qfn
Цоколевка для VSC7984XYF (корпус qfn). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для VSC7984XYF.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
VSC7984XYF подходит для 6 применениеs: 10 GbE Optical Transmitter Modules, SONET/SDH Optical Transport, Clocked Optical Data Links, Optical Amplifier and Modulator Interfaces, High-Speed Optical Test Equipment, High-Speed Optical Backplane Equipment.
10 GbE Optical Transmitter Modules
The VSC7984XYF fits a 10 GbE optical module that uses an external electroabsorption modulator because it provides selectable retiming for jitter improvement and controls for output bias voltage, modulation voltage, and duty cycle. The internal operational amplifiers and on-chip voltage reference reduce the amount of external circuitry needed to stabilize the modulator drive state. Implement the manufacturer reference topology and verify the complete output path against the module's jitter, rise-time, and extinction-ratio requirements.
SONET/SDH Optical Transport
The VSC7984XYF is suitable for SONET/SDH transmit paths operating around the documented 11.3 Gb/s class, particularly where a clocked EAM driver with selectable retiming is required. Adjustable bias and modulation voltage allow the optical operating point to be matched to the selected electroabsorption modulator, while duty-cycle control supports optimization of the driven waveform. Confirm the applicable SONET/SDH rate, jitter tolerance, and mask requirements against the manufacturer test guidance.
Clocked Optical Data Links
In a clocked optical link, the VSC7984XYF can provide selectable data retiming to reduce the effect of accumulated source jitter before the signal reaches the electroabsorption modulator. Its internal operational amplifiers support the high-speed drive function, while the on-chip reference contributes to stable control of bias and modulation conditions. The design must still provide a low-noise supply, controlled clocking, matched differential routing, and suitable output termination.
Optical Amplifier and Modulator Interfaces
The VSC7984XYF can serve as the electrical drive interface between a high-speed transmitter and an external electroabsorption modulator used in amplified optical systems. Adjustable output bias voltage, modulation voltage, and duty cycle provide the controls needed to establish the modulator operating point. The device's documented 11.3 Gb/s class operation supports high-bandwidth transport links, but eye opening, extinction ratio, and power penalties must be verified in the assembled optical path.
High-Speed Optical Test Equipment
The VSC7984XYF can be used in laboratory and production test equipment that must electrically emulate the drive conditions of an EAM-based optical transmitter. Selectable retiming permits testing multiple timing arrangements, and the bias, modulation-voltage, and duty-cycle controls provide adjustable stimulus conditions. A measurement fixture must preserve controlled impedance and minimize fixture reflections, otherwise fixture degradation can obscure the jitter and waveform performance of the device under test.
High-Speed Optical Backplane Equipment
The VSC7984XYF is applicable to high-speed optical backplane and data-conversion equipment that terminates a serial electrical signal into an external electroabsorption modulator. Selectable retiming can improve jitter behavior when source-device and transmitter timing are imperfect, while internal amplifiers and the on-chip reference support controlled drive operation. Deployment requires careful lane-to-lane skew control, a continuous reference plane, and qualification across every supported data-rate and temperature condition.
Справочные инженерные данные для VSC7984XYF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Product Type | Electroabsorption modulator driver |
| Brand | Microchip Technology |
| Package | QFN |
| Nominal Data Rate | 11.3 Gb/s |
| Documented Maximum Data Rate | 12.5 Gb/s |
| Data Retiming | Selectable |
| Output Bias Control | Adjustable output bias voltage |
| Modulation-Voltage Control | Adjustable modulation voltage |
| Duty-Cycle Control | Adjustable duty cycle |
| Internal Functions | Operational amplifiers and on-chip voltage reference |
Ключевые отличия
- Selectable data retiming for jitter control (против Generic EAM drivers without a documented retiming option)
- Integrated modulation-control functions (против EAM drivers requiring more external stabilization circuitry)
- Three independent transmitter adjustments (против EAM drivers with fewer adjustable operating parameters)
Заметки по проектированию
Use the manufacturer reference circuit as the starting point for differential output routing and termination. Keep the high-speed paths short, preserve continuous reference planes, avoid unnecessary stubs and test pads, and match length and geometry to the PCB stack-up. Verify the impedance and differential-mode behavior with a design that reflects the actual fabrication stack-up rather than relying only on a nominal characteristic-impedance calculation.
Provide a clean supply and place local decoupling at the device power pins with the shortest possible current-loop path. Separate sensitive reference and bias circuitry from noisy return currents where the layout permits. Review supply tolerance, sequencing, and the maximum permitted supply voltage in the manufacturer datasheet before assigning capacitors or designing power-state transitions.
Do not assume that every VSC7984 family member has the same retiming, control, speed, or pin arrangement as VSC7984XYF. Check the exact ordering code, package drawing, pin-description table, and electrical-characteristics tables. In particular, distinguish the principally documented 11.3 Gb/s rating from the related 12.5 Gb/s statement before approving a higher-rate design.
Информация о соответствии
The accessible product information does not state the environmental or automotive qualification status for the exact VSC7984XYF ordering code.
