XMC4400F100F512BAXUMA1 - 120MHz Cortex-M4 MCU | Infineon
Артикул: XMC4400F100F512BAXUMA1 ✓ АктивенXMC4400F100F512BAXUMA1 Обзор
A microcontroller is a programmable semiconductor that combines a processor core, memory, peripherals, and communication interfaces on one integrated circuit. The ARM Cortex-M4 core gives this device a 32-bit architecture suited to industrial automation, embedded networking, motor control, and data acquisition. The XMC4000 family combines the Cortex-M4 core with on-chip Ethernet, analog interfaces, timers, communication peripherals, and safety-oriented features designed for industrial applications.
The 120 MHz operating frequency provides processing headroom for protocol handling, control-loop execution, diagnostics, and application logic. Its 512 KB flash memory stores firmware, configuration data, and application code, while the device's Ethernet MAC supports connection to 10/100 Mb/s Ethernet networks. The manufacturer identifies the XMC4400-F100F512-BA family variant as an industrial 32-bit Cortex-M4 device with 10/100 Ethernet MAC functionality.
The XMC4400F100F512BAXUMA1 ordering designation identifies the 100-pin package, 512 KB flash configuration, industrial temperature/profile option, tape-and-reel order code, and grade suffix. Its 100-pin PG-LQFP-100 package offers a larger pin count than small-outline packages, supporting broad access to the mixed-signal and communication resources available in the XMC4000 family. Exact pin assignments and exposed-pad connections should be taken from the Infineon XMC4400 datasheet and package drawing before layout release.
Typical uses include industrial Ethernet controllers, factory automation nodes, embedded gateways, motor and power-control systems, industrial sensors, and networked test equipment. For these applications, the device's 120 MHz Cortex-M4 performance and integrated 10/100 Ethernet MAC reduce the need for separate network controllers while keeping real-time processing and communications on the same device.
PCB design should treat all 100 package terminals and the exposed pad, where applicable, according to the manufacturer's land pattern and thermal guidance. Decoupling, analog grounding, Ethernet magnetics, clock stability, and exposed-pad vias are especially important in a mixed-signal industrial design. Firmware selection should also verify the complete ordering-code decoding and all peripheral variants associated with the exact derivative.
This product page combines the manufacturer ordering information with practical engineering guidance for industrial networking, firmware selection, PCB implementation, and drop-in replacement assessment. It is intended to help engineers identify whether the XMC4400F100F512BAXUMA1 matches a required Cortex-M4, 512 KB flash, 10/100 Ethernet, and 100-pin LQFP platform before requesting a quotation.
Аналоги без доработки для XMC4400F100F512BAXUMA1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
XMC4400-F100K512-BA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
XMC4400-F100F512-BA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
XMC4400F100F512BAXUMA1 Максимальные параметры и электрические характеристики
| Product Type | 32-bit industrial microcontroller |
| Processor Core | ARM Cortex-M4 |
| Architecture | 32-bit |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 512 KB (512K x 8) |
| Ethernet MAC | 10/100 Ethernet MAC |
| Product Series | XMC4000 |
| Корпус | PG-LQFP-100 |
| Total Terminal Count | 100 terminals |
| Тип монтажа | Surface mount |
| Package Temperature Code | PG-LQFP-100-25 |
| Qualification Segment | Industrial |
| Core Variant | Cortex-M4 |
| Program Memory Organization | 512K x 8 bits |
Руководство по цоколевке XMC4400F100F512BAXUMA1 в корпусе pg-lqfp-100-25
Цоколевка для XMC4400F100F512BAXUMA1 (корпус pg-lqfp-100-25). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для XMC4400F100F512BAXUMA1.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
XMC4400F100F512BAXUMA1 подходит для 6 применениеs: Industrial Ethernet Gateway, Factory Automation Controller, Connected Motor Control, Industrial Sensor Hub, Embedded Data Acquisition System, Industrial Condition Monitoring.
Industrial Ethernet Gateway
The XMC4400F100F512BAXUMA1 fits an industrial Ethernet gateway because its 120 MHz ARM Cortex-M4 core can process protocol and application tasks while the integrated 10/100 Ethernet MAC handles network communication. Its 512 KB of flash provides space for a bootloader, network stack, configuration, logging, and gateway logic. The 100-pin PG-LQFP package also provides a practical route to mixed industrial peripherals. Use a qualified Ethernet transceiver, appropriate network magnetics, line protection, and carefully separated analog and digital return paths. Validate throughput, latency, boot behavior, and thermal performance with the final firmware and network loading.
Рекомендуется
Factory Automation Controller
The XMC4400F100F512BAXUMA1 is suitable for a factory automation controller that combines deterministic control processing with industrial network connectivity. Its Cortex-M4 architecture executes at up to 120 MHz, allowing firmware to service timers, communication traffic, diagnostics, and control logic. The 512 KB flash supports embedded application code and configuration, while the industrial XMC4000 platform identity aligns it with equipment designed for embedded control. Match the exact ordering variant to the controller's voltage, temperature, qualification, and lifecycle requirements, and test all digital I/O timing against the motor, sensor, and safety-system architecture.
Рекомендуется
Connected Motor Control
The XMC4400F100F512BAXUMA1 can serve as the supervisory controller in a connected motor-control system. At 120 MHz, the Cortex-M4 core can execute motion algorithms, monitor protection events, and communicate status over the 10/100 Ethernet MAC, while 512 KB of flash holds control code and parameter sets. The PG-LQFP-100 package offers extensive board access compared with small-outline alternatives. Power-stage design remains separate from the MCU, so use appropriate gate drivers, current sensing, isolation, and protection. Validate control-loop timing, fault response, thermal behavior, and network latency under worst-case operating conditions.
Рекомендуется
Industrial Sensor Hub
The XMC4400F100F512BAXUMA1 fits an industrial sensor hub that must acquire measurements, perform local processing, and forward results over Ethernet. Its 120 MHz Cortex-M4 core leaves processing capacity for filtering, calibration, diagnostics, and protocol handling, while 512 KB of flash can hold firmware and calibration tables. The integrated 10/100 Ethernet MAC supports network reporting without a separate communications controller. Signal conditioning and precision analog interfaces should be designed around the MCU's documented analog characteristics. Review grounding, isolation, sensor excitation, and Ethernet magnetic-component placement to prevent noise or ground potential differences from degrading measurement accuracy.
Рекомендуется
Embedded Data Acquisition System
The XMC4400F100F512BAXUMA1 supports embedded data-acquisition systems that need local control and Ethernet-based data transfer. The 120 MHz ARM Cortex-M4 core can handle buffering, scaling, event detection, and communication overhead, and the 512 KB flash is appropriate for embedded firmware and configuration. Its 100-pin package allows connection to multiple sensors and digital interfaces while retaining the industrial profile. Use the datasheet to confirm available analog channels and their electrical limits. Calibrate acquisition accuracy, separate analog and digital supplies where appropriate, and test sampling behavior under communications traffic and high-frequency switching conditions.
Рекомендуется
Industrial Condition Monitoring
The XMC4400F100F512BAXUMA1 is appropriate for networked condition-monitoring equipment that combines sensor processing with remote communications. The 120 MHz Cortex-M4 core can run filtering, feature extraction, event logic, and diagnostics, while the 512 KB flash supports firmware updates and operating parameters. The 10/100 Ethernet MAC permits remote configuration and telemetry over a wired industrial network. Select the exact industrial profile only after checking temperature and qualification requirements. Pay particular attention to sensor isolation, clock accuracy, watchdog behavior, recovery after power loss, and secure update procedures in the final system architecture.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для XMC4400F100F512BAXUMA1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | XMC4400-F100K512-BA | XMC4400-F100F512-BA |
|---|---|---|---|
| Brand | Infineon | Infineon | Infineon |
| Package | PG-LQFP-100 | PG-LQFP-100 | PG-LQFP-100 |
| Processor Core | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 |
| Maximum CPU Frequency | 120 MHz | 120 MHz | 120 MHz |
| Architecture | 32-bit | 32-bit | 32-bit |
| Flash Memory | 512 KB (512K x 8) | 512 kB | 512 KB |
| Ethernet MAC | 10/100 Ethernet MAC | 10/100 Ethernet | 10/100 Ethernet MAC |
| Application Segment | Industrial | Industrial | Industrial |
Ключевые отличия
- Combines a 120 MHz Cortex-M4 core with integrated 10/100 Ethernet MAC (против XMC4400-F100K512-BA)
- Full orderable suffix supports production BOM identification (против XMC4400-F100F512-BA)
- Matches the XMC4000 industrial networking positioning (против XMC4400-F100K512-BA)
Заметки по проектированию
Build the layout from the exact PG-LQFP-100 land pattern and pin-description table in the Infineon XMC4400 documentation. Place mandatory supply and decoupling capacitors at their specified pins with the shortest possible traces and vias. Keep sensitive analog inputs away from Ethernet PHY, clock, and high-current return paths, and provide a continuous reference plane without splitting it beneath the MCU. Verify every one of the 100 terminals mechanically and electrically against the package drawing before release.
Validate junction temperature and exposed-pad heat flow using the exact package thermal model and the device's operating profile. If the package drawing specifies an exposed pad, connect it according to the manufacturer instruction and use multiple thermal vias to spread heat into an adequate copper area. Avoid creating a thermal-via void beneath the package, and do not rely on a small top-layer copper region for industrial ambient temperatures. Corner and center temperature measurements under maximum clock and Ethernet activity can reveal assembly or layout weaknesses.
Apply the manufacturer's interface-layout rules for external clocks, analog inputs, reset, and Ethernet communications. Keep clock traces short, continuously referenced, and away from switching nodes; provide the specified startup and load components where required. Ethernet magnetics and the physical-layer transceiver should be positioned according to the reference layout so the differential pair has a continuous return path and avoids unnecessary splits. Check interface rise times and ringing with an oscilloscope using suitable probing practices.
Do not treat the base ordering designation XMC4400-F100F512-BA and the full suffix XMC4400F100F512BAXUMA1 as interchangeable without decoding the manufacturer ordering table. Confirm package code, temperature profile, grade, flash variant, reel format, and qualification requirements against the BOM. Also verify the exact pin multiplexing and peripheral differences between F100F512 and F100K512 derivatives. A similar CPU frequency, flash capacity, and family name do not by themselves prove production drop-in equivalence.
Информация о соответствии
The device is identified as an industrial microcontroller, but no specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration appears in the product information. AEC-Q100 is not applicable because this is an industrial rather than automotive-qualified device.
