Mga Produkto (44,000+)

VSC8211XVW - 1-Port GbE Cu/Fiber PHY, 117-LBGA | Microchip
VSC8211XVW

VSC8211XVW - 1-Port GbE Cu/Fiber PHY, 117-LBGA | Microchip

The Microchip Technology VSC8211XVW is a single-port Gigabit Ethernet copper/fiber PHY transceiver that combines a 1.25 Gbps SerDes with a triple-speed (10/100/1000BASE-T) transceiver in a 117-LBGA (10x14 mm) package. The device operates from a 3 V to 3.6 V supply and supports copper PHY, 1000BASE-X fiber PHY, and 100BASE-FX media converter configurations with automatic media detection. A PHY (Physical Layer transceiver) is the interface block that converts between raw digital data and electrical or optical signaling on a copper or fiber link. In the system hierarchy, a PHY sits below the MAC (Media Access Control) block, which in turn sits below the network switch or host controller. Transceivers combine a PHY with parallel MAC-side interfaces so that a single silicon device can terminate a physical link while handing data to a MAC layer over a standard bus. Key features of the VSC8211XVW include full triple-speed auto-negotiation support, a 1000BASE-X compliant SerDes for fiber modules, and a wide set of MAC-side ports: GMII, RGMII, MII, TBI, and RTBI. The two serial interfaces (SGMII/1000BASE-X SerDes and the parallel MAC ports) let a system reduce signal overhead compared with a purely parallel GMII connection while still supporting legacy 10/100 MII-based MACs. Technically, the device combines an integrated 1.25 Gbps SerDes with a copper PHY capable of 10, 100, and 1000 Mb/s operation, using patented line driver technology that improves tolerance to noise and cable-plant imperfections. Auto-Media detection allows copper and fiber ports to be supported with one physical network port, reducing connector count and board area in media converter designs. Typical applications include Gigabit uplinks on Fast Ethernet switches, fiber-to-copper media converters, 100BASE-FX industrial and campus links, GBIC and SFP optical module designs, and industrial Ethernet equipment requiring a single PHY that bridges copper and fiber media. Design guidance: the 117-LBGA package demands careful via-in-pad and thermal-via layout, and the high-speed SerDes and copper pairs require controlled-impedance routing with clean references. Confirm regulator sequencing and 3.3 V rail decoupling close to the supply pins. This page consolidates manufacturer datasheet detail, interface compatibility analysis, drop-in alternatives in the same package family, and practical PCB guidance that is not gathered in one place in the original device documentation.

RFQ Kontak
VSC8221XHH - Low-Power Gigabit Copper SFP PHY | Microchip
VSC8221XHH

VSC8221XHH - Low-Power Gigabit Copper SFP PHY | Microchip

Microchip Technology VSC8221XHH is a low-power Gigabit Ethernet over copper PHY with a 1.25 Gbps SerDes, a single 3.3 V supply, and less than 700 mW power consumption. It supports 10BASE-T, 100BASE-TX, and 1000BASE-T through a 100-TFBGA 9 x 9 mm package. The device is designed for copper SFP, GBIC, and media-converter equipment. A copper Ethernet PHY is a physical-layer transceiver that translates digital MAC data into signals suitable for twisted-pair cabling and recovers those signals at the receiving endpoint. The VSC8221 occupies the PHY layer within the Ethernet hierarchy: an Ethernet transceiver integrates a physical-layer device with a SerDes interface for connection to a media-access controller or switching fabric. Its purpose is to provide interoperable copper connectivity while limiting module power and board area. The principal feature is support for triple-speed copper Ethernet at 10, 100, and 1000 Mb/s. Its 1.25 Gbps SerDes supports both SGMII and SerDes-to-Category 5 operating modes, allowing the same PHY to be used in SFP and media-converter designs. The manufacturer identifies the part as the smallest, lowest-power Gigabit Ethernet-over-copper PHY in its product family and as suitable for demanding cable-plant environments. The VSC8221 is designed to support 140 m of Category 5 unshielded twisted-pair cable while meeting stringent SFP power-consumption requirements. It also supports PICMG 2.16 and 3.0 Ethernet backplanes at approximately 500 mW and provides tolerance to NEXT, FEXT, echo, and system noise. These characteristics make the PHY appropriate where copper reach, electromagnetic-noise immunity, and compact module power are simultaneous design priorities. Typical uses include 1000BASE-X copper SFP modules, GBIC-style copper interfaces, Ethernet media converters, and backplane or embedded networking equipment. The same package can support a MAC-to-copper connection through 1000BASE-X SerDes operation or a MAC connection through the four-pin or six-pin SGMII interface. Automatic or user-controlled SerDes behavior provides additional flexibility during system bring-up. When designing with the VSC8221, verify the selected magnetics, impedance-controlled copper routing, reference clock, and SGMII or SerDes interface against the manufacturer data sheet. A 3.3 V-only architecture simplifies supply design, but the complete module still requires careful thermal, isolation, and return-path planning under sustained 1 Gb/s traffic. This page consolidates the verified manufacturer and distributor information for VSC8221XHH, including power, interface, speed, cable-reach, pricing, and application details. It also identifies the limits of the available substitute data so engineers can distinguish confirmed same-family options from unsupported cross-brand replacements.

RFQ Kontak
VSC8224XHG - 4-Port Gigabit Ethernet PHY | Microchip Technology
VSC8224XHG

VSC8224XHG - 4-Port Gigabit Ethernet PHY | Microchip Technology

Microchip Technology VSC8224XHG is a four-port Gigabit Ethernet transceiver IC integrating four independent 10BASE-T, 100BASE-TX, and 1000BASE-T PHYs with four 1000BASE-X-compatible serializer/deserializer interfaces in a thermally enhanced 260-pin plastic ball grid array package. The device operates from a 3.3 V supply and combines copper and fiber-oriented network connectivity in one 19 mm package. An Ethernet PHY is a physical-layer interface IC that converts digital MAC data into electrical signaling for a network medium and converts received signaling back into digital data. The VSC8224 belongs to the Ethernet interface IC hierarchy, where each integrated transceiver supports a physical port while coordinating with an external or embedded media-access controller through RGMII or RTBI-compatible interfaces. The principal feature of VSC8224XHG is port density: four independent triple-speed Ethernet transceivers are integrated into one device. Each port supports 10 Mbps, 100 Mbps, and 1 Gbps operation. Four 1000BASE-X-compatible SerDes channels provide an additional high-speed physical interface, while automatic or user-programmable RGMII timing compensation helps accommodate MAC-to-PHY timing differences. On-chip series termination resistors also reduce the need for external receive-side termination components. The thermally enhanced 260-pin PBGA package is intended for high-port-density equipment where four separate physical-layer devices would consume excessive board area. Its four copper PHYs suit switching and routing platforms, while the 1000BASE-X-compatible SerDes channels can support fiber-oriented links when paired with appropriate optical and physical-layer circuitry. The integrated architecture reduces component count and simplifies multiport routing-board layouts. Typical applications include four-port Gigabit Ethernet switches, routers, network interface cards, industrial Ethernet equipment, and communications infrastructure. Design teams must preserve the manufacturer's recommended high-speed layout, provide suitable power and ground distribution, and keep Ethernet magnetics and signal-routing paths compact. Because the package exposes 260 balls, careful thermal management and via-array layout are essential. This page consolidates verified distributor pricing, package information, functional application guidance, and cross-reference findings that are not presented together in a typical distributor listing. It also distinguishes the confirmed VSC8224XHG orderable variant from related VSC8224 documentation and avoids asserting unverified pin-level substitutions.

RFQ Kontak
VSC8228XRC-01 - Dual 4.25G Retimer | Microchip
VSC8228XRC-01

VSC8228XRC-01 - Dual 4.25G Retimer | Microchip

The Microchip Technology VSC8228XRC-01 is a dual-port, dual-output clock and data recovery retimer supporting serial link rates from 125 Mbps to 4.25 Gbps in a 64-pin TQFP package measuring 10 mm by 10 mm. The device provides two FibreTimer clock recovery units for bidirectional signal conditioning in system interconnect and serial backplane applications. A clock and data recovery IC, or CDR, extracts timing information from a corrupted or degraded serial stream and reconstructs a clean data and clock output. Within the hierarchy of integrated circuits, a CDR belongs to the Clock & Timing and Interface IC families, supporting reliable data transfer when transmitted signals experience attenuation, jitter, or noise. The VSC8228 is designed for Fibre Channel, Gigabit Ethernet, SONET/SDH, and InfiniBand system interconnect. The primary features of the VSC8228XRC-01 include two retiming ports, support for data rates up to 4.25 Gbps, operation from a minimum rate of 125 Mbps, and two independent clock recovery units. Its dual-channel architecture allows a single device to condition two serial links, reducing component count and simplifying board-level clock distribution. The 64-TQFP surface-mount package also supports compact backplane and communications equipment layouts. Technically, the FibreTimer architecture separates clock recovery from ordinary signal buffering and performs bidirectional signal conditioning. This is particularly useful when loss, skew, or accumulated jitter would compromise a high-speed point-to-point link. A single reference clock can be used for acquisition, allowing the two recovered channels to share a coherent timing reference. Confirm the required reference-clock topology, operating mode, and channel configuration against the Microchip VSC8228 documentation before laying out the PCB. Typical uses include Fibre Channel links, Gigabit Ethernet backplanes, SONET/SDH equipment, and InfiniBand interconnects. The device is also appropriate for proprietary serial backplanes operating at or below 4.25 Gbps where recovered clock and data outputs are required at both ends of a link. PCB implementation should prioritize short, controlled-impedance traces, solid reference planes, and symmetric routing between the transmit and receive channels. Place clock-generation and decoupling networks close to their associated device pins, and follow the manufacturer’s recommended termination and layout guidance to minimize signal-integrity degradation. This page combines the manufacturer’s device description with application-focused engineering guidance, package information, sourcing questions, and selection criteria that help engineers determine whether the VSC8228XRC-01 fits a high-speed recovery or retiming requirement.

RFQ Kontak
VSC8242XHX-01 Ethernet Interface Controller | Microchip
VSC8242XHX-01

VSC8242XHX-01 Ethernet Interface Controller | Microchip

The Microchip Technology VSC8242XHX-01 is an Ethernet interface controller associated with the VSC8242 family of multi-port 10/100/1000BASE-T physical-layer devices. Its family supports RGMII and RTBI MAC interfaces, positioning it for network equipment that requires multiple copper-Ethernet ports connected to a switching or processing subsystem. An Ethernet interface controller is a semiconductor that manages communication between a MAC, network processor, or switching fabric and physical network media. Within the network hierarchy, the controller sits above the PHY layer and below the packet-processing layer. Its operating role is therefore distinct from a general-purpose microprocessor: the surrounding system supplies packets and configuration, while the controller interfaces those signals with copper Ethernet ports. The key documented feature of the related VSC8244 listing is quad-port 10/100/1000BASE-T operation with RGMII and RTBI MAC interfaces. The VSC8242XHX-01 shares the same Vitesse and Microchip Technology product lineage and is identified as an interface controller. Detailed electrical ratings, interface timing, register definitions, and operating limits for the exact XHX-01 ordering code should be confirmed in the manufacturer datasheet before the device is released into production. Network-interface applications include managed Ethernet switches, industrial Ethernet equipment, network appliances, telecommunications access hardware, and multi-port embedded systems. In these systems, the controller reduces the number of discrete media-access and PHY interface functions required on the main board while providing a standardized path between the Ethernet PHYs and the switching or host logic. A quad-port configuration can also simplify board routing when several copper ports are needed in one chassis. The controller still requires careful treatment of high-speed digital interfaces, including controlled-impedance routing, solid reference planes, and minimized differential-pair crosstalk. Magnetic-interface protection and external line filtering are normally implemented separately from the controller. Before layout begins, download the manufacturer datasheet and confirm the XHX package drawing, exposed-pad requirements, pin assignments, reference-voltage circuitry, clock expectations, and decoupling recommendations. The package used by this ordering code is not identified consistently across product listings, so its mechanical dimensions and land pattern must not be inferred from a generic QFN footprint.

RFQ Kontak
VSC8244XHG - Quad Gigabit Ethernet PHY | Microchip Technology
VSC8244XHG

VSC8244XHG - Quad Gigabit Ethernet PHY | Microchip Technology

The Microchip Technology VSC8244XHG is a quad-port Gigabit Ethernet PHY transceiver with 10/100/1000BASE-T support, RGMII and RTBI MAC interfaces, four drivers and four receivers, and a 260-PBGA package. It operates from a 3 V to 3.6 V supply and is designed for low-cost Ethernet switch, router, and embedded networking equipment. A multi-port Ethernet PHY is an interface IC that converts data between a digital MAC or switching fabric and physical copper network links. The VSC8244 family combines four Gigabit Ethernet channels in one device, reducing the number of external PHY components required in a network system. Its RGMII interface supports high-speed digital connections to a network processor or switch ASIC, while RTBI provides an alternative MAC-facing interface for compatible designs. The principal feature of the VSC8244XHG is its quad-port architecture, which allows one device to terminate four Ethernet ports. The manufacturer describes the VSC8244 as the industry’s smallest, lowest-power quad-port Gigabit Ethernet transceiver for low-cost RGMII and RTBI switch and router applications. In 1000BASE-T mode, the manufacturer states that power consumption is 30% lower than the next-best competitor. The 3 V to 3.6 V operating range suits systems using a regulated 3.3 V power rail. The 260-PBGA package provides a high pin count for four integrated channels and their associated interfaces, while its lead-free construction and RoHS compliance support modern manufacturing requirements. The exact pin assignments, register map, clocking requirements, and electrical limits should be taken from the Microchip VSC8244 datasheet and reference design documentation. Typical applications include four-port Gigabit Ethernet switches, router interfaces, industrial Ethernet equipment, network appliances, and embedded systems that need multiple copper Ethernet ports. The PHY is positioned between the Ethernet magnetics and the system’s MAC or switching logic, so board design must account for high-speed digital signals, differential pairs, controlled impedance, grounding, and isolated network interfaces. For a new design, compare the complete Microchip VSC8244 datasheet, reference schematics, and support for the intended MAC interface before layout begins. The quad-channel package is not interchangeable with a single-channel PHY, and the 260-BGA land pattern requires careful fanout and via planning.

RFQ Kontak
VSC8247YJB-01 - 10G Quad CDR with EDC | Microchip
VSC8247YJB-01

VSC8247YJB-01 - 10G Quad CDR with EDC | Microchip

The Microchip Technology VSC8247YJB-01 is a quad-channel clock and data recovery IC with adaptive electronic dispersion compensation (EDC), four outputs, and a 144-FCBGA package measuring 13 mm by 13 mm. It operates from 8.5 Gbps to 11.3 Gbps per channel and supports 10G Ethernet, SONET, 8G Fibre Channel, and 10G QDR InfiniBand protocols. A clock and data recovery IC is a high-speed interface component that reconstructs a usable clock from a received serial data stream. Where the incoming signal has experienced timing jitter or channel dispersion, the CDR detects timing deviation and adjusts its recovered clock. EDC adds adaptive equalization to compensate for signal degradation, making the VSC8247YJB-01 suitable for demanding serial links rather than ordinary low-speed interface recovery. The primary features of the device are four independent recovery channels, four clock outputs, an 8.5 Gbps to 11.3 Gbps operating range, and integrated adaptive EDC. These characteristics allow one device to serve multiple high-speed lanes in a networking or storage system. The four-output architecture can reduce the number of discrete recovery components required when a board must recover several related signals. Technically, the VSC8247YJB-01 combines clock and data recovery with adaptive dispersion compensation in a single 144-FCBGA package. This integration places timing recovery and channel-loss mitigation beside the physical-layer receive path. The listed protocol support gives designers a practical framework for selecting operating modes, although configuration, reference-clock, media, and electrical requirements must be confirmed against the manufacturer documentation before a board is released. Typical applications include 10G Ethernet ports, SONET/SDH equipment, 8G Fibre Channel links, and 10G QDR InfiniBand interfaces. It can also support multi-lane backplanes, optical-module receive paths, network-interface controllers, and high-speed test equipment where deterministic clock recovery and channel equalization are important. A critical design consideration is that recovery performance depends on the complete channel, including transmitter characteristics, trace losses, connectors, clocking, and receive equalization. PCB layout, power distribution, reference decoupling, and input signal integrity must therefore be developed as part of the high-speed design rather than added after schematic completion. This page organizes the device protocol, package, speed, and channel information into an engineering-focused guide, adds application analysis, and clearly identifies the electrical, pinout, lifecycle, and drop-in replacement details that still require manufacturer confirmation.

RFQ Kontak
VSC8247YJB-02 - 8.5-11.3 Gbps Quad CDR | Microchip
VSC8247YJB-02

VSC8247YJB-02 - 8.5-11.3 Gbps Quad CDR | Microchip

The Microchip Technology VSC8247YJB-02 is a four-channel clock and data recovery (CDR) and retimer IC for high-speed serial links operating from 8.5 Gbps to 11.3 Gbps. It provides four outputs and is packaged in a 144-FCBGA measuring 13 mm by 13 mm. A clock and data recovery IC is a timing and signal-integrity component that extracts or reconstructs a usable clock from a high-speed serial data stream. It belongs to the clock and timing IC hierarchy within broader interface and semiconductor systems. By recovering timing information and retiming data, a CDR can reduce accumulated jitter and help a receiver interpret a serial signal reliably. The VSC8247 combines four channels in one package for multi-lane networking, optical-module, and backplane applications where parallel channel density is important. The VSC8247 operates across an 8.5 Gbps to 11.3 Gbps line rate, allowing one device family to cover multiple high-speed protocols. Supported applications include 10G Ethernet, SONET, 8G Fibre Channel, 10G QDR InfiniBand, and legacy rates. Its four-channel architecture also makes it suitable for emerging 4×10G and 10×10G CFP-module architectures, as well as high-density photonic integrated circuit designs. Four outputs give each recovered channel a corresponding output path for downstream circuitry. The device integrates clock recovery and retiming functions rather than functioning only as a passive clock distributor. Retiming establishes a new sampling boundary for received serial data, while clock recovery provides a stable timing reference for the associated channel. This is important in multi-gigabit links where transmission-line effects, package parasitics, connector transitions, and inter-symbol interference can degrade the eye opening. The Microchip VSC8247 datasheet identifies the family as a versatile CDR and retimer for 10G-class serial communication. Typical deployments include 10G Ethernet equipment, SONET/SDH interfaces, Fibre Channel systems, QDR InfiniBand links, CFP optical modules, and high-density photonic integrated circuits. The quad-port configuration reduces the number of discrete timing devices needed in a four-lane design, while a single 13 mm by 13 mm FCBGA can support dense line-card and pluggable-module layouts. Designers should evaluate the complete receiver channel rather than relying on nominal line-rate capability alone. Signal losses, connector and package parasitics, reference-clock quality, board-level jitter, and the available power architecture can all affect margin. Confirm the manufacturer’s recommended layout, reference-clock requirements, decoupling network, impedance-controlled interfaces, and thermal conditions against the Microchip VSC8247 datasheet before releasing a high-speed PCB. This product summary consolidates the verified operating range, channel count, output count, supported protocols, package information, and manufacturer datasheet reference for engineers evaluating the VSC8247YJB-02 in high-speed serial-interface designs.

RFQ Kontak
VSC8248KITEV - Application-Specific Clock/Timing IC | Microchip
VSC8248KITEV

VSC8248KITEV - Application-Specific Clock/Timing IC | Microchip

The Microchip Technology VSC8248KITEV is an application-specific clock and timing integrated circuit listed for clock buffers, drivers, and interface-controller applications. The device is identified by the full VSC8248KITEV ordering code, but the accessible manufacturer and distributor records do not expose its complete electrical specifications, package dimensions, pin configuration, frequency range, or operating-temperature limits. The part is therefore presented as a specialized timing-control device rather than being assigned unverified performance values. An application-specific clock/timing IC is a semiconductor that generates, redistributes, buffers, conditions, or controls clock signals within a larger electronic system. Clock and timing ICs sit within the broader clock and timing IC category, where they support digital logic, communications equipment, industrial controls, and other systems that depend on stable signal propagation. The VSC8248KITEV is specifically categorized as an IC interface controller by multiple product records. The primary identified feature is its specialized role in clock and timing signal handling. Unlike a general-purpose microcontroller, this device is intended to support the timing architecture of its host equipment. Its ordered suffix includes the KITEV package and temperature-grade identifier, but the accessible records do not provide enough information to map those codes to confirmed package dimensions, pin count, lead finish, temperature range, or qualification status. The physical package and symbol should be confirmed against the manufacturer datasheet before PCB layout or schematic release. The part is listed by Microchip Technology and is distributed as an application-specific clock/timing component. Current catalog pages identify inventory and ordering information, including the VSC8248KITEV-ND ordering representation used by one authorized channel. However, the listings do not expose explicit quantity-break prices in the retrieved text, so no price tier is reproduced on this page. Current sourcing, lead time, and stock status should be requested through the quote form on this page. Typical design roles for this device include clock distribution, interface timing control, communications equipment, industrial electronics, and embedded control systems. Because the exact input and output ranges are not stated in the accessible records, designers should confirm signal amplitudes, frequencies, supply requirements, I/O standards, and timing tolerances before selecting pull-up resistors, termination networks, or downstream clock devices. Those decisions must be based on the manufacturer pin description and electrical characteristics rather than assumptions based on the clock-buffer category alone. The primary design consideration is to treat VSC8248KITEV as a timing-critical component. Validate the complete clock path with worst-case loading, enable sequencing, power-up behavior, and propagation-delay variation. Review the package drawing and pin-description table during schematic capture, then preserve the manufacturer's recommended layout and decoupling guidance in the PCB implementation. If those items remain unavailable, obtain the controlled manufacturer datasheet before releasing a high-volume or safety-related design. This page consolidates the confirmed manufacturer identity, category, ordering code, current catalog sources, application context, and engineering checkpoints for VSC8248KITEV. It clearly separates confirmed information from parameters requiring manufacturer documentation, helping engineers evaluate sourcing and design readiness without presenting unverified numerical specifications as facts.

RFQ Kontak
VSC8248YJH-01 - 11.3 Gbps Quad CDR | Microchip Technology
VSC8248YJH-01

VSC8248YJH-01 - 11.3 Gbps Quad CDR | Microchip Technology

The Microchip Technology VSC8248YJH-01 is a quad-channel clock and data recovery (CDR) integrated circuit designed for 8.5 Gbps to 11.3 Gbps high-speed serial links. The device includes clock and data recovery with error detection and correction (EDC) for XFI-to-XFI+ conversion and is supplied in an orderable package identified by the YJH designator. A CDR is a high-speed line interface component that recovers a serial bit stream and its associated clock from a waveform that may have accumulated timing distortion, noise, and jitter during transmission. Positioned within clock and timing integrated circuits, the VSC8248 family supports network equipment operating at 10 Gb/s class line rates. Multiple recovered channels allow one device to serve interfaces that require parallel clock-and-data recovery rather than a single-lane retimer. The VSC8248 supports data rates from 8.5 Gbps through 11.3 Gbps. This range covers 1.25 Gb/s Ethernet, 2 Gb/s and 4 Gb/s Fibre Channel, and 2.5 Gb/s and 5 Gb/s InfiniBand applications identified in the product documentation. At the upper operating region, its 11.3 Gbps capability supports modern 10 Gb/s networking and related optical or copper transport systems without requiring a separate recovery function for each lane. The principal feature set includes four CDR channels, XFI-to-XFI+ conversion, and EDC capability. XFI provides a wide parallel data interface for transmitting serialized high-speed data, while XFI+ includes clock-forwarding information. Supporting conversion between these interface forms allows a system to bridge legacy XFI connections to newer XFI+ endpoints while recovering the transmitted clock. EDC helps correct transmission errors that may occur in the physical link. Typical deployments include 10 Gb/s Ethernet switching equipment, Fibre Channel systems, InfiniBand adapters, optical network terminals, and network interface cards. The multi-lane architecture can reduce component count in quad-port designs while centralizing clock recovery, error correction, and interface conversion. Its multi-gigabit data-rate range makes it suitable for equipment designs that must bridge protocol or physical-layer variations while maintaining a common high-speed fabric. For layout and implementation, preserve controlled-length and impedance-continuous high-speed connections, provide compliant termination and decoupling, and follow the manufacturer’s recommended reference design. Differential and high-speed clock/data paths require short return paths and careful isolation from noisy power converters. Confirm the exact YJH package dimensions, exposed-pad arrangement, pin assignments, and thermal limits against the manufacturer datasheet before releasing PCB artwork. This page combines the manufacturer product information with a practical view of protocol applications, interface considerations, sourcing options, and validated drop-in alternatives. It is intended to help engineers identify whether the VSC8248YJH-01 matches a high-speed recovery requirement before beginning board-level implementation.

RFQ Kontak
VSC8248YJH-02 - 4-Port 11.3 Gbps SFI-to-XFI CDR | Microchip
VSC8248YJH-02

VSC8248YJH-02 - 4-Port 11.3 Gbps SFI-to-XFI CDR | Microchip

The Microchip Technology VSC8248YJH-02 is a four-port clock and data recovery (CDR) application-specific IC that converts serial interface (SFI) signals into extended small form-factor pluggable (XFI) signals at data rates from 8.5 Gbps to 11.3 Gbps. The device includes integrated electronic dispersion compensation (EDC) and is packaged in a 225-FCBGA measuring 16 mm by 16 mm. A clock and data recovery IC is a timing-recovery semiconductor used in high-speed serial links to recover the transmitted clock from the data stream and regenerate a synchronized data output. In the broader hierarchy, the VSC8248 belongs to clock and timing ICs, interface ICs, and application-specific clock/timing semiconductors. Its four-port architecture allows one device to serve multiple high-speed channels while centralizing configuration and diagnostics. The principal operating capability is the supported 8.5 Gbps to 11.3 Gbps per-channel data-rate range. Four outputs support independent high-speed interface channels, while integrated EDC extends usable reach by compensating signal degradation. The manufacturer documentation also identifies programmable output and integrated diagnostics as major device features, making the IC suitable for systems where link health must be monitored during operation rather than only during manufacturing. The VSC8248YJH-02 is intended for optical and copper Ethernet infrastructure equipment operating at multi-gigabit line rates. Its SFI-to-XFI conversion function allows a system to use different serial-interface conventions on the line-card and backplane sides. The 225-FCBGA package provides a high pin count for power distribution, high-speed differential signaling, configuration, monitoring, and diagnostic functions, but it also requires a dense multilayer PCB and careful high-speed layout practices. Typical applications include Ethernet switches, routers, optical line cards, network-interface equipment, telecommunications aggregation systems, and high-speed backplane equipment. The four-channel organization can reduce the number of discrete conversion devices required in a multiport line card while providing consistent clock recovery and diagnostics across channels. Designers should preserve controlled-impedance routing for every high-speed differential pair, maintain continuous reference planes, and place decoupling and clock-support components according to the manufacturer evaluation-board layout. Because the FCBGA has a dense pitch and numerous supply connections, power and ground planes require careful partitioning to prevent coupled noise from degrading CDR margin. Production designs should also validate the complete SFI and XFI channel in the target connector, cable, optical, or backplane environment. This product page combines the verified device identity, package format, interface conversion, supported data-rate range, and EDC capability with practical PCB guidance, application guidance, and strict drop-in-replacement analysis. The component is positioned for engineers evaluating a four-port, 11.3 Gbps-capable CDR rather than a general-purpose clock generator or conventional low-speed clock buffer.

RFQ Kontak
VSC8248ZREV - 11.3 Gbps Quad CDR | Microchip Technology
VSC8248ZREV

VSC8248ZREV - 11.3 Gbps Quad CDR | Microchip Technology

Microchip Technology VSC8248ZREV is a four-channel clock and data recovery device operating from 8.5 Gbps to 11.3 Gbps. It integrates adaptive electronic dispersion compensation for high-speed optical and backplane links and is supplied in a bulk package configuration. A clock and data recovery device, commonly called a CDR, extracts a usable data stream from a high-speed serial link and recovers the associated clock. This function sits within the physical-layer hierarchy of optical communications, Ethernet, Fibre Channel, and InfiniBand equipment. By regenerating timing and signal integrity at the receiver, a CDR allows downstream circuitry to operate without directly processing the degraded waveform received over a long channel. The VSC8248ZREV provides four recovery channels, programmable input equalization, and a KR-compliant multi-tap output driver. Adaptive electronic dispersion compensation helps compensate for channel-related signal degradation. Together, these features target difficult printed-circuit-board and optical backplane channels where frequency-dependent loss, reflections, and timing distortion can impair data recovery. The device supports operation from 8.5 Gbps through 11.3 Gbps and is associated with IEEE 802.3ae, IEEE 802.3aq, SFF-8431, 8G Fibre Channel, and 10G QDR InfiniBand protocols. These protocol associations make the device relevant to 10G Ethernet, Fibre Channel, and InfiniBand signal paths, provided that the complete system timing, reference clock, and lane configuration satisfy the device requirements. Typical applications include 10G Ethernet optical-module receivers, Fibre Channel switching equipment, InfiniBand adapters, backplane equalizers, and high-speed serial retiming subsystems. In each case, the CDR can reconstruct the receive clock while equalization and dispersion compensation improve signal margin before data reaches the packet-processing or framing layer. Designers should evaluate the recovered-clock behavior, reference requirements, lane-to-lane skew, channel loss, and firmware configuration before committing a board layout. The bulk package designation indicates a shipment format rather than a surface-mount form factor, so the exact mechanical package, land pattern, pin count, and solder process must be confirmed before PCB design begins. This product overview connects protocol support, recovery bandwidth, equalization, adaptive dispersion compensation, and replacement considerations to help engineers determine whether the VSC8248ZREV fits a specific 10G-class link architecture.

RFQ Kontak
VSC8256EV - Quad 1G/10G Serial Repeater | Microchip Technology
VSC8256EV

VSC8256EV - Quad 1G/10G Serial Repeater | Microchip Technology

The Microchip Technology VSC8256EV is a quad 1G/10G serial-to-serial, protocol-agnostic repeater/retimer with hardware-based host-side-only 10GBASE-KR auto-negotiation and training. It is designed for board-level signal integrity applications requiring retiming of high-speed serial links. The device supports 10.3125 Gbps LAN mode, 9.95328 Gbps WAN mode, and 1.25 Gbps mode, according to the available VSC8256 datasheet summary. Its signal-conditioning architecture is protocol agnostic, allowing it to be used with multiple serial interfaces rather than being restricted to one specific protocol. The VSC8256 is associated with a small-form-factor, low-power FCBGA package, making it suitable for compact telecommunications and networking equipment. The VSC8256EV ordering code is listed by Microchip Technology and is available through authorized distributors and distributor marketplaces. The core engineering benefit of this component is that it combines multi-lane serial retiming with integrated 10GBASE-KR auto-negotiation and training, reducing the amount of external protocol-specific support required in board-level designs. Typical implementation areas include 10G Ethernet backplanes, serial links between cards, telecommunications equipment, and other systems where loss, skew, or jitter can compromise high-speed transmission. Engineers should confirm the exact package dimensions, pin assignments, thermal limits, and electrical characteristics against the manufacturer datasheet before layout or production release.

RFQ Kontak
VSC8256YMR - Quad 10G Repeater/Retimer | Microchip
VSC8256YMR

VSC8256YMR - Quad 10G Repeater/Retimer | Microchip

The Microchip Technology VSC8256YMR is a quad 1G/10G protocol-agnostic serial-to-serial repeater/retimer designed for board-level Ethernet signal-integrity applications. It provides four serial channels operating at 1G or 10G, integrates hardware-based host-side 10GBASE-KR auto-negotiation and training, and is associated with a low-power 256-FCBGA package. Its central function is to recover and retime high-speed serial links while supporting board-level connectivity across WAN, LAN, switching, and telecom equipment. A repeater/retimer is a signal-integrity IC positioned between two serial endpoints to reduce timing uncertainty, recover degraded signals, and extend reliable communication over circuit-board channels. Within the semiconductor hierarchy, the VSC8256YMR belongs to the serial transceiver and interface-controller class rather than the general-purpose Ethernet PHY category. This distinction matters because the device is protocol-agnostic and focuses on physical-layer signal recovery rather than converting between conventional Ethernet media and a digital host interface. The device supports four 1G/10G serial paths in one device, allowing a multiport system to use a consistent retiming architecture across parallel lanes. Its hardware-based host-side 10GBASE-KR auto-negotiation and training functions support link establishment over backplane-style electrical channels. Combining these functions in a compact FCBGA can reduce the number of separate repeater devices required in dense line-card and switching-platform designs while keeping signal timing behavior consistent among channels. The 256-FCBGA package provides a high pin count suitable for four independent high-speed channels, their associated supply and ground connections, control interfaces, and configuration or reference connections. Dense ball-pitch packaging also demands careful PCB layout, short high-speed escape paths, controlled reference planes, and independent supply-return distribution. The package is intended for surface-mount assembly and is suited to multilayer boards designed specifically for multi-gigabit signal routing rather than simple two-layer prototyping. Typical board-level uses include 10G Ethernet switching equipment, WAN and LAN interface line cards, telecom backplanes, and systems requiring protocol-independent signal recovery between endpoints. In these applications, the retimer can help compensate for connector, package, and PCB-channel losses while preserving deterministic link behavior. It is also relevant to equipment designers implementing four-lane 1G or 10G links where channel-to-channel timing consistency and training control are important design objectives. Design teams should evaluate the complete channel path rather than treating the retimer as a standalone specification. Loss and jitter budgets, transmit and receive equalization, connector transitions, reference-clock quality, power sequencing, and the PCB stack-up determine whether a 10G channel closes reliably. Decoupling and power-plane design are particularly important in a 256-ball package because each high-speed retimer channel requires clean references and controlled return paths for dependable signal recovery. This product page consolidates the manufacturer description, package information, sourcing details, application guidance, and pin-compatible family options into a concise engineering reference. It also highlights the distinction between protocol conversion, Ethernet media access, and true repeater/retimer functions to help designers select the correct device for high-speed board-level signal-integrity requirements.

RFQ Kontak
VSC8256YMR-01 - Quad 10G SFI/XFI Repeater | Microchip
VSC8256YMR-01

VSC8256YMR-01 - Quad 10G SFI/XFI Repeater | Microchip

Microchip Technology VSC8256YMR-01 is a quad-channel 1G/10G serial-to-serial repeater/retimer with four 10Gbps SFI-to-XFI channels in a 256-ball FCBGA measuring 17 x 17 mm. The device is protocol-agnostic and supports 1G and 10G operation, making it suitable for board-level Ethernet signal-integrity designs. A repeater/retimer is a signal-conditioning semiconductor that receives a high-speed serial waveform, regenerates it, and transmits a cleaner copy to the next circuit. Unlike a simple passive redriver, a retimer can recover timing through receive and transmit equalization. The VSC8256 sits within the broader hierarchy of Ethernet interface ICs, serial transceiver support ICs, and semiconductor signal-integrity devices. The VSC8256 provides four independent serial channels and integrates hardware-based, host-side-only 10GBASE-KR auto-negotiation and training. This combination allows a board designer to address difficult printed-circuit-board loss on Ethernet links while retaining compatibility with protocol-independent serial interfaces. The manufacturer describes the device as a low-power solution for board-level signal-integrity applications. Its SFI-to-XFI architecture places separate serial-side and host-side interfaces around each repeater channel. In a 10G design, the device can receive SFI traffic and provide conditioned XFI output, helping recover signal integrity across connector, package, and PCB channels. Protocol independence allows the same device to support multiple Ethernet or compatible serial-transfer arrangements rather than requiring a fixed end protocol. Typical applications include 10GBASE-KR backplanes, 10G Ethernet switches and routers, WAN and LAN interface equipment, server networking, and high-speed line cards. The four-channel architecture can reduce the number of separate retimer components required in a multiport design, while the 17 x 17 mm FCBGA supports dense board layouts requiring high pin density. The primary design consideration is that a 256-ball FCBGA requires careful PCB escape routing, power and ground distribution, and thermal analysis. Differential traces should follow the manufacturer's reference layout, and decoupling should be placed close to the supply pins. Signal-integrity performance depends on the complete channel, including connector and trace geometry, rather than on the IC alone. This page combines the manufacturer's device description with package-level sourcing information and practical selection guidance. It distinguishes the orderable MPN from the VSC8256 family designation, summarizes the confirmed four-channel architecture, and identifies the board-level considerations that matter when integrating this Ethernet retimer into a 10Gbps system.

RFQ Kontak
VSC8257EV - Quad 1G/10G Ethernet PHY | Microchip Technology
VSC8257EV

VSC8257EV - Quad 1G/10G Ethernet PHY | Microchip Technology

The Microchip Technology VSC8257EV is an evaluation platform for the VSC8257 quad 1G/10G serial-to-serial Ethernet PHY, featuring VeriTime IEEE 1588v2 network timing and support for dual-sided 10GBASE-KR in a low-power FCBGA device. The verified distributor listing identifies VSC8257EV as a telecom interface IC, while the manufacturer page describes the underlying VSC8257 PHY. The product therefore belongs to the Ethernet physical-layer and telecom-interface ecosystem rather than the general-purpose processor or memory categories. A serial-to-serial Ethernet PHY is an interface integrated circuit that converts digital data into high-speed electrical signaling for network equipment. The VSC8257 family supports 1G and 10G Ethernet links and incorporates Microchip’s VeriTime technology for IEEE 1588v2 network timing. Its dual-sided 10GBASE-KR capability, auto-negotiation, and link training make it relevant to carrier-grade, enterprise, and industrial Ethernet systems where deterministic timing and interoperable backplane links are important. The verified product information identifies four PHY channels, 1G/10G operation, serial-to-serial Ethernet operation, IEEE 1588v2 timing support, dual-sided 10GBASE-KR, auto-negotiation, training, and a low-power FCBGA implementation. These features distinguish it as a multiport network interface rather than a single-port transceiver. The available evidence does not specify lane data rates in decimal form, power consumption, clock requirements, register depth, temperature grades, or individual ball assignments. Typical VSC8257EV evaluation use includes demonstrating 10GBASE-KR links between line cards, validating network timing behavior with VeriTime, testing auto-negotiation and training across backplanes, and bringing up multiport Ethernet equipment. Engineers can use the evaluation platform to examine signal integrity, clocking, firmware, board-level routing, and interoperability before integrating the production VSC8257 device into carrier, switching, or industrial network equipment. A key engineering caution is that evaluation-board access does not guarantee a pin-for-pin production-board replacement. Confirm the exact VSC8257 package, exposed-pad requirements, reference clocks, power rails, SerDes lane assignments, connector interfaces, and thermal constraints before committing a PCB layout. The provided sources do not include the complete schematic, bill of materials, pinout, or detailed electrical characteristics. This page consolidates the verified manufacturer and distributor information, identifies where published data is unavailable, and distinguishes the VSC8257 evaluation platform from verified drop-in alternatives. It is intended to support component identification and design planning without presenting unverified package, pricing, pinout, or cross-reference claims.

RFQ Kontak
VSC8479YHQ-01 - 10G SFI4.1 SerDes Transceiver 195-FCBGA | Microchip
VSC8479YHQ-01

VSC8479YHQ-01 - 10G SFI4.1 SerDes Transceiver 195-FCBGA | Microchip

The Microchip Technology VSC8479YHQ-01 is a 1:16 / 16:1 multi-rate SerDes transceiver with integrated Clock and Data Recovery (CDR) and Clock Multiplier Unit (CMU), packaged in a 195-ball FCBGA measuring 12 mm x 12 mm. Operating continuously from 9.953 Gbps to 11.35 Gbps, the device supports SFI4.1 and SFI-5.1 interface standards with a 16-bit parallel datapath for 10 Gigabit Ethernet, SONET/SDH OC-192, OTN OTU2, and Fibre Channel applications. A SerDes (Serializer/Deserializer) is a mixed-signal integrated circuit that converts between parallel and high-speed serial data streams while embedding clock recovery, equalization, and line-coding functions. As a class of physical-layer (PHY) interconnect ICs, SerDes devices sit between the MAC/ASIC framer and the optical module, forming the bridge between the digital chip domain (typically LVDS/PECL parallel buses) and the analog serial optical/electrical domain. The VSC8479 family belongs to the multi-rate 10G transceiver category, which spans oversampled and bit-serial architectures for telecom and datacom line cards. Key features include integrated CDR with low-jitter performance, a reference-less or reference-clock CMU for synthesizing the line-side baud clock from a low-frequency system reference, programmable transmit pre-emphasis and receive adaptive equalization for backplane and optical reach extension, and an I2C/SPI management interface for system bring-up. The 195-FCBGA package uses controlled-collapse chip connection with flip-chip die attach, providing short electrical paths for multi-GHz signals and a thermal envelope suitable for forced-air-cooled line-card environments. Architecture-wise, the device integrates four physical lanes (per SFI4.1 direction) with 16-bit datapaths, internal AC-coupling, and on-chip termination. The 17 mm x 17 mm footprint described in vendor collateral refers to the bare die-area footprint class typical of FCBGA-195 assemblies, enabling cost and board-area reduction for SFP+/XFP module and small-form-factor line-card designs. Typical applications include 10G Ethernet SFP+ and XFP transceivers, OTN OTU2 line cards, SONET OC-192 short-reach modules, multi-rate muxponder/framer I/O, and 10G Fibre Channel host-bus adapters. Per the vendor product page, every device is tested at high speed to ensure production-grade performance. Designers should evaluate AC-coupling capacitor selection, PCB material (low-loss FR-4 or Megtron), and matched-length routing for the four differential lanes to meet SFI4.1 jitter masks. The integrated CDR reduces BOM by eliminating an external clock-recovery block. This page aggregates distributor stock, parametric drop-in alternatives, and engineering design notes that complement the Microchip datasheet and Mouser spec summary (msco-s-a0003388128-1).

RFQ Kontak
VSC8479YY - 11.3 Gbps 1:16 Transceiver | Microchip Technology
VSC8479YY

VSC8479YY - 11.3 Gbps 1:16 Transceiver | Microchip Technology

Microchip Technology VSC8479YY is a telecom interface IC implementing a 1:16 transmit and 16:1 receive transceiver with integrated clock and data recovery unit (CDR) and clock multiplier unit (CMU). The device is supplied in a 244-pin FCBGA package measuring 17 mm by 17 mm, and a listed distributor specification identifies a maximum data rate of 11.3 Gbps. Its operating frequency begins at 9.953 Gbps according to the manufacturer product description. A high-speed serial interface transceiver is a semiconductor device that converts between parallel or narrower-width data paths and high-speed serial communication links. The VSC8479YY belongs to the broader interface IC and telecommunications IC hierarchy. Integrating the transceiver, CDR, and CMU functions in one package reduces the number of separate clock-recovery and multiplexing blocks required in a multi-lane optical or backplane interconnect system. The principal functional characteristics are a 1:16 parallel-to-serial transmission ratio, a 16:1 serial-to-parallel reception ratio, integrated clock recovery, and integrated clock multiplication. These functions support systems requiring multiple high-speed lanes to be aggregated or recovered efficiently. The 11.3 Gbps data-rate capability is particularly relevant to optical transport, backplane, and other high-bandwidth telecommunications infrastructure where parallel-to-serial conversion and deterministic clocking are required. The VSC8479 architecture integrates clocking with data conversion instead of treating the CDR and CMU as independent blocks. This combination is intended to provide a comprehensive interface solution for designs that need recovered clocks, multiplied reference clocks, and bidirectional lane conversion. Exact recovery ranges, jitter specifications, reference-clock requirements, lane polarity, voltage levels, and power consumption were not included in the supplied verified records and must therefore be confirmed in the manufacturer documentation. Typical implementation areas include telecommunications equipment, optical transport modules, network switching systems, and other multi-lane serial links that require parallel-to-serial and serial-to-parallel conversion. System designers should also account for the FCBGA package requirements, including fine-pitch escape routing, multilayer PCB construction, controlled impedance, and power and ground distribution across 244 package contacts. The principal design consideration is package integration. A 17 mm by 17 mm FCBGA requires careful PCB footprint design, thermal management, and high-density routing rules. Power rails, reference clocks, high-speed differential pairs, and control interfaces should be evaluated against the manufacturer's pinout, reference design, and layout guidance before schematic or PCB sign-off. This product page combines the verified Microchip product summary, distributor package information, availability references, and practical implementation guidance. It distinguishes published VSC8479 characteristics from parameters that still require datasheet confirmation and does not treat unverified substitute parts as drop-in replacements.

RFQ Kontak
VSC8479YYY - 11.3 Gbps 16-Bit Transceiver | Microchip
VSC8479YYY

VSC8479YYY - 11.3 Gbps 16-Bit Transceiver | Microchip

The Microchip Technology VSC8479YYY is a 1:16 and 16:1 high-speed serial transceiver operating continuously from 9.953 Gbps to 11.3 Gbps, with integrated clock and data recovery, clock multiplication, and a 244-FCBGA package measuring 17 mm by 17 mm. It serves OC-192, 10GbE, and 10GFC-oriented signal-chain designs that require parallel-to-serial and serial-to-parallel conversion in one device. A high-speed transceiver is a semiconductor interface that converts wide parallel data into a high-speed serial stream and converts received serial data back into parallel form. The VSC8479 belongs to the broader transceiver and data-converter hierarchy while integrating timing-recovery functions needed to establish and recover a reliable high-speed data stream. Its 16-bit interface, continuous frequency coverage, and integrated CDR and CMU reduce the amount of external high-speed conversion circuitry required in communications equipment. Key features include a 1:16 transmit fanout, a 16:1 receive aggregation, a 16-bit parallel data path, and a documented continuous operating span of 9.953 Gbps to 11.3 Gbps. The device is identified as a single Ethernet-class port transceiver by Mouser and as a telecom IC transceiver by DigiKey. Its single-chip, 17 mm by 17 mm implementation is specifically presented as a way to reduce board area and system cost in compact, price-sensitive modules. The integrated clock and data recovery unit supports extraction or recovery of timing from the associated high-speed signal path, while the clock multiplier unit supplies the required derived clock functions. This integration can simplify synchronization architecture, but board implementation still requires careful high-speed layout, controlled impedance, short return paths, compliant clocking, power delivery, isolation, and signal-integrity verification. Exact power, voltage, pin, and environmental limits must be confirmed in the manufacturer datasheet before layout release. Typical uses include 10GbE and 10GFC optical-module electronics, OC-192 transport interfaces, FEC equipment, telecommunications line cards, and compact high-speed network modules. The part is most appropriate where one device must support both serialization and deserialization functions at rates covered by its 9.953 Gbps-to-11.3 Gbps operating range. System designers should evaluate lane timing, reference-clock requirements, thermal performance, and protocol interoperability before production deployment. The principal design consideration is that this is a very-high-speed mixed-signal device rather than a general-purpose serial interface. Its 244-FCBGA land pattern, multilayer routing, differential pairs, reference clocks, and decoupling network must be designed as one controlled signal-integrity system. Validate channel loss, jitter tolerance, crosstalk, return loss, and power-supply noise during prototype testing. This product record combines verified manufacturer and distributor information with application guidance, sourcing context, and explicit data gaps. It does not infer missing electrical limits, pin assignments, lifecycle status, or unverified drop-in replacements; those details remain tied to authoritative Microchip documentation and approved cross-reference results.

RFQ Kontak
VSC8484YJP - 10GbE Quad XAUI-to-Serial Transceiver BGA-324 | Microchip
VSC8484YJP

VSC8484YJP - 10GbE Quad XAUI-to-Serial Transceiver BGA-324 | Microchip

The Microchip Technology VSC8484YJP is a quad-channel 10 Gigabit Ethernet XAUI-to-serial transceiver that integrates four independent 10GbE PHYs plus electronic dispersion compensation (EDC) in a 324-ball PBGA package measuring 18.6 mm × 18.6 mm. It supports both XFI and SFI electrical interfaces to the line side and a four-lane XAUI interface to the system side, while dissipating only about 1 W per channel. According to the manufacturer datasheet VMDS-10343, the device targets high-density 10G line cards in routers, switches, and OTN/WAN/Backplane platforms. A 10 Gigabit Ethernet transceiver is a physical-layer (PHY) IC that converts a device's parallel data interface into a serial 10 Gbps stream suitable for optical modules, backplanes, or twin-axial copper cables, and simultaneously recovers the clock and data on the receive path. Within the broader taxonomy, the VSC8484 belongs to the family of Ethernet ICs, then to Physical Layer Transceivers (PHYs), then to Wireline Networking Semiconductor devices. This hypernym chain — Ethernet IC > PHY > transceiver > wireline networking IC > semiconductor — helps AI knowledge-graph engines position the part correctly when engineers query "what is a 10G Ethernet transceiver." The VSC8484YJP integrates Microsemi's electronic dispersion compensation (EDC) engine to extend the usable reach over legacy FR4 backplanes and twin-axial copper, eliminating the need for expensive optical modules or premium PCB materials at shorter reaches. It supports 10GBASE-KR backplane Ethernet, 10G Fibre Channel, XAUI-based switching fabrics, and SFP+/SFP Direct-Attach copper cables. Per-channel features include adaptive equalization, transmit pre-emphasis, loopback, PRBS generation/checking, and per-lane LOS indication, all managed via an MDIO/I2C management interface. Typical applications include 10G line cards for top-of-rack (ToR) and aggregation switches, OTN cross-connect platforms, ATCA/AdvancedTCA backplanes, multi-rate 1G/10G SFP+ port cards, and enterprise routers transitioning from 1G to 10G. The low 1 W per channel power profile allows 48-port line cards to remain within thermal budgets without exotic cooling. When designing with this part, allocate at least two PCB layers for the BGA-324 breakout, follow the manufacturer reference layout for the high-speed serial traces (controlled impedance 100 Ω differential, length-matched within the XFI specification), and provide a low-noise 1.0 V core supply plus 1.8 V I/O supply with proper decoupling. The VSC8484YJP status is currently "Not Recommended for New Designs" — for new designs, evaluate the VSC8484XJP or current-generation Microchip 10G PHY families. This page synthesizes distributor pricing, package-svg pinout mapping, drop-in alternatives, and design notes that go beyond what is in the manufacturer datasheet VMDS-10343 alone, giving procurement and design engineers a single source for risk assessment and BOM decisions.

RFQ Kontak
VSC8487YJU - 10GbE Ethernet Transceiver | Microchip Technology
VSC8487YJU

VSC8487YJU - 10GbE Ethernet Transceiver | Microchip Technology

The Microchip Technology VSC8487YJU is a 10GbE Ethernet backplane transceiver that converts between a single XFI serial interface and dual XAUI lanes. It is packaged for high-speed printed-circuit-board designs and combines EDC, KR support, and IEEE 1588v2 timing functionality for timing-critical Ethernet systems. The lead-free construction is identified explicitly for the related VSC8487YJU-15 ordering code. An Ethernet transceiver is an interface IC that connects a digital communications system to a physical transmission medium. XFI and XAUI are high-speed serial interfaces commonly used to move 10GbE traffic across boards, backplanes, chassis, and equipment interconnects. A device that translates XFI to dual XAUI can bridge a narrow serial-side connection to two parallel high-speed lanes while centralizing electrical signaling, clocking, and timing functions in one component. Key features include support for 10GbE operation, EDC and KR, dual XAUI connectivity, and IEEE 1588v2 timing compliance. These capabilities make the VSC8487 family relevant to synchronized networking equipment, Ethernet switching systems, industrial automation platforms, and test equipment that requires deterministic traffic timing. The exact electrical ratings, operating temperature, and package dimensions should be confirmed against the manufacturer datasheet before release to production. The VSC8487 belongs to Microchip’s family of dual-channel XAUI-to-serial transceivers. The manufacturer identifies VSC8487-15 and VSC8488-15 as timing-oriented devices supporting industry-standard protocol encapsulations. This positioning places the VSC8487YJU within the broader hierarchy of Ethernet interface IC, network interface controller, data-converter semiconductor, and communication IC. Typical applications include 10GbE switching equipment, backplane routing systems, industrial control networks, synchronized test and measurement platforms, and telecommunications infrastructure. EDC helps the receiver recover data impaired by interconnect loss, while KR support addresses known backplane signal-integrity challenges. IEEE 1588v2 compliance is especially useful when synchronized time or deterministic event ordering must be maintained across the network. PCB implementation requires careful high-speed layout practices, including controlled impedance, short differential connections, suitable return paths, and compliance with the manufacturer’s reference design and decoupling guidance. Clocking, reference circuitry, reset behavior, and device configuration must follow the datasheet because incorrect sequencing or an unsuitable reference implementation can impair link operation even when the device itself is functioning correctly. This page organizes the VSC8487YJU’s confirmed networking capabilities, timing features, ordering variants, and practical design implications. It also separates documented facts from parameters that require direct confirmation, helping engineers assess fit, establish pin-compatible sourcing options, and plan robust 10GbE backplane implementations before schematic release.

RFQ Kontak
VSC8488XJU Dual-Channel XAUI Transceiver | Microchip
VSC8488XJU

VSC8488XJU Dual-Channel XAUI Transceiver | Microchip

The Microchip Technology VSC8488XJU is a dual-channel XAUI-to-serial transceiver interface IC designed for timing-critical telecommunications and data-networking equipment. Microchip identifies the VSC8487-15 and VSC8488-15 devices as fully IEEE 1588v2-compliant solutions supporting industry-standard protocol encapsulations. The VSC8488XJU is supplied in a surface-mount package and is identified by the XJU ordering suffix. An XAUI-to-serial transceiver is an interface semiconductor that converts XAUI parallel signaling into high-speed serial lanes and, in a dual-channel implementation, supports two independent signal paths. This type of device belongs to the communications interface hierarchy: serial transceiver → XAUI interface → telecommunications interface IC → semiconductor. It is used where timing, protocol synchronization, and reliable high-speed data transfer are central to the equipment architecture. The principal product-level benefits identified by Microchip are full dual-channel operation, IEEE 1588v2 compliance, support for timing-critical applications, and compatibility with industry-standard protocol encapsulations. These characteristics make the device suitable for transport, aggregation, switching, timing, and test equipment designed around XAUI links. Exact lane rates, electrical limits, clocking requirements, supply voltages, pin assignments, and package dimensions must be confirmed in the manufacturer datasheet before schematic or PCB implementation. VSC8488XJU is most relevant to systems requiring two XAUI channels and deterministic timing behavior. The IEEE 1588v2 capability supports precision time protocols, while protocol-encapsulation support can simplify interoperability with established telecommunications data paths. Its two-channel architecture can also reduce component count compared with separate single-channel transceivers when the host PCB has sufficient routing, power, thermal, and signal-integrity resources. The main design considerations are high-speed differential-routing discipline, compliant clock distribution, reference-plane continuity, controlled impedance, and careful separation between sensitive clock paths and noisy digital or power-conversion sections. Follow the manufacturer’s recommended decoupling, layout, and test procedures exactly. Confirm that the PCB footprint, pin assignment, solder-process limits, and absolute maximum ratings match the exact XJU package before releasing a production design. This page combines the manufacturer’s VSC8488 family positioning with package, procurement, comparison, and design guidance for engineers evaluating the VSC8488XJU in dual-channel XAUI systems.

RFQ Kontak
VSC8488YJU - 10GbE Dual-Channel XAUI Transceiver | Microchip
VSC8488YJU

VSC8488YJU - 10GbE Dual-Channel XAUI Transceiver | Microchip

The Microchip Technology VSC8488YJU is a dual-channel, 10 GbE XAUI-to-serial transceiver designed for timing-critical backplane, switching, and telecommunications equipment. Each channel supports 10 Gb/s serial signaling, and the device supports IEEE 1588v2 timing features for deterministic network synchronization. The component is supplied in a 196-FCBGA package measuring 15 mm by 15 mm. An XAUI transceiver is an interface IC that converts a parallel XAUI data stream into a high-speed serial lane and recovers the parallel stream on the receive side. It belongs to the serial communication transceiver hierarchy, which includes SerDes devices, physical-layer transceivers, network interface controllers, and broader communications semiconductors. Such devices move parallel data across printed circuit boards, backplanes, chassis, and rack-to-rack links. The VSC8488-15 family is identified by Microchip as a dual-channel XAUI-to-serial transceiver supporting 1588v2 compliance and industry-standard protocol encapsulations. Two integrated channels can reduce component count on systems that require parallel transmit and receive paths. The device also supports external clocking and reference arrangements for synchronization-sensitive infrastructure, although the complete clocking configuration must follow the manufacturer datasheet and reference design. At the physical layer, the VSC8488YJU combines differential high-speed serial I/O with digital control, configuration, clocking, and fault-management functions. Differential signaling improves common-mode noise rejection, while low-jitter clock distribution is important when the transceiver participates in synchronized Ethernet traffic. Board-level implementation requires controlled-impedance routing, short matched differential pairs, solid reference planes, and carefully positioned decoupling. Typical uses include 10GbE switching line cards, router and gateway interfaces, telecommunications aggregation equipment, optical-module host interfaces, network timing systems, and test equipment. In each case, the device serves as the high-speed electrical interface between parallel fabric or processing logic and narrow serial links. System architects should confirm lane count, protocol encapsulation, reference-clock requirements, and board-management features against the ordered device variant. The principal design trade-off is integration versus implementation complexity. A dual-channel transceiver consolidates two high-speed interfaces in one BGA, but it demands careful power-plane planning, thermal management, and BGA assembly control. Use the Microchip reference design and datasheet power-up sequence rather than relying on generic SerDes power rails. This page organizes the device data into a specification summary, application guidance, package information, and a practical selection comparison with closely related Microchip transceiver variants. It highlights board-level constraints that are not apparent from the MPN alone and distinguishes device variants that can look interchangeable in distributor catalogs.

RFQ Kontak
VSC8489YJU - 10G Ethernet Transceiver | Microchip Technology
VSC8489YJU

VSC8489YJU - 10G Ethernet Transceiver | Microchip Technology

The Microchip Technology VSC8489YJU is a 10G Ethernet transceiver interface controller in a 196-FCBGA (15 x 15 mm) surface-mount package. The device belongs to the VSC8489, VSC8490, and VSC8491 family of single-port and dual-port 10G Ethernet transceivers designed for electrical backplane and optical module host-card applications. Its stated application coverage includes SFP+ SR, LR, ER, and ZR fiber modules with EDC support. A 10G Ethernet transceiver interface IC is a semiconductor that connects a host controller or digital processing system to high-speed copper or optical-module interfaces. It sits between the board-level digital logic and a network-facing medium, supporting Ethernet signal generation, reception, clocking, and control through an interface such as SPI. This makes it part of the broader hierarchy of network interface controllers, Ethernet interface ICs, and telecommunications semiconductors. The VSC8489 family is designed around 10 Gigabit Ethernet data rates for backplane and optical host-card designs. Listings for the related VSC8489YJU-02 identify the device as a dual 10G reduced XAUI to XFI/SFI PHY in the same 196-FCBGA package, while VSC8489YJU-16 is identified as a single-port 10G PHY. The VSC8489YJU is therefore positioned for board designs that require a dedicated high-speed Ethernet transceiver front end rather than a general-purpose microcontroller I/O. Microchip describes the VSC8489 family as a highly flexible solution for electrical backplane and optical module host-card applications. That positioning is significant because these systems require separate transmit and receive signal paths, low-latency data transfer, and host configuration over a serial control interface. Product descriptions for related variants also identify RoHS 3 compliance and a surface-mount implementation. Typical uses include 10G SFP+ line-card designs, optical transceiver host cards, electrical backplane equipment, telecom aggregation systems, and high-speed data-processing infrastructure. In these applications, the transceiver provides the physical-layer interface between the host FPGA or ASIC and the network medium, while the surrounding processor handles packet processing and system management. When planning a PCB layout, use the manufacturer's pin-description table and package drawing for all 196 ball assignments, differential routing, supply decoupling, and exposed-connection requirements. Because the package is a large fine-pitch FCBGA, high-speed signal integrity and power distribution are as important as the nominal transceiver specifications. This page consolidates the manufacturer product-family information, distributor package and interface details, practical placement guidance, and a comparison of documented VSC8489 ordering variants. It is intended to accelerate initial design review while keeping pin-level implementation decisions tied to the official Microchip documentation.

RFQ Kontak