Mga Produkto (44,000+)

EPC4QC100T - 4Mb FPGA Config PROM, 100-PQFP | Altera / Intel FPGA
EPC4QC100T

EPC4QC100T - 4Mb FPGA Config PROM, 100-PQFP | Altera / Intel FPGA

The Altera (Intel Programmable Solutions Group) EPC4QC100T is an Enhanced Configuration Device designed to store and deliver configuration bitstreams to Altera/Intel FPGAs such as the Cyclone, Stratix, and APEX families. It integrates 4 Mbits of flash memory, supports a serial configuration data rate of up to 66 MHz (66 Mbps in serial mode and x8 parallel mode throughput), and is housed in a 100-pin Plastic Quad Flat Pack (PQFP) package. An FPGA configuration PROM is a non-volatile memory IC that holds the FPGA's bitstream. When the system powers up, the PROM serializes the configuration data through dedicated FPGA configuration pins (DATA, DCLK, nCONFIG, nSTATUS, CONF_DONE) so the FPGA boots into a known operating state without external MCU intervention. Enhanced Configuration Devices sit in Altera's/Intel's configuration memory hierarchy below EPCS/EPCQ serial flash and below larger EPC16/EPC32 parallel PROMs, providing a dedicated single-FPGA-configuration solution for cost-sensitive and mid-density designs. Key features include in-system programmability via IEEE Std. 1149.1 (JTAG) and Altera-supported serial interface commands, 3.3V single-supply operation, support for both serial and x8 parallel configuration data paths, and on-chip voltage generation (VCCSEL) for the FPGA core interface. The device also supports MultiVolt I/O for compatibility with 1.8V, 2.5V, 3.3V, and 5.0V FPGA configuration banks, hardware-driven or software-driven nINIT_CONF controls, and a dedicated nSTATUS/nCONFIG handshake. Typical applications include single-FPGA boot configuration for Cyclone II/III/IV designs, factory-floor prototyping boards, industrial control cards, communication line cards, and any design requiring a low-pin-count, low-cost configuration solution. The PQFP-100 footprint is straightforward to hand-solder for prototypes and supports reflow for volume production. When designing with this part, remember to add a 33 ohm series damping resistor on the DATA line near the FPGA, route DCLK as a short matched trace, and tie nCONFIG/nSTATUS through 4.7 kohm pull-ups. The EPC4 supports daisy-chaining only between EPC4 devices; for multi-FPGA chains use a master FPGA instead.

RFQ Kontak
EPC4QC100TQ - 4Mb FPGA Config PROM 66MHz | Intel / Altera
EPC4QC100TQ

EPC4QC100TQ - 4Mb FPGA Config PROM 66MHz | Intel / Altera

The Intel (formerly Altera) EPC4QC100TQ is a 4-Mbit in-system programmable configuration PROM designed to configure high-density SRAM-based FPGAs including Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. Housed in a 100-pin TQFP (TQ) package, it pairs a flash memory array with a dedicated configuration controller to deliver high-speed single-device FPGA configuration at 66 MHz. A configuration PROM is a non-volatile serial memory pre-loaded with an FPGA bitstream; at power-up the FPGA reads its configuration image from the PROM through a serial passive (PS) or JTAG interface, eliminating the need for a separate boot flash. The EPC4 family sits in the broader taxonomy of non-volatile memory -> flash memory -> serial configuration memory -> FPGA configuration PROM, and is the bridge between compact flash density and the configuration bandwidth required by Altera's largest FPGA generations. Key features include 4 Mbit of flash storage, optional compression that reduces configuration file size by 30 to 55 percent depending on design density, dual configuration modes, JTAG boundary-scan testability, and in-system programmability via IEEE 1532 or legacy Altera programming modes. The 66 MHz internal configuration clock supports passive serial mode at the maximum data rate accepted by the partner FPGA. The device uses a 5.0 V-tolerant interface with a 3.3 V core supply typical of mid-2000s FPGA configuration ecosystems. The 100-pin TQFP provides generous ground and power pins for low-noise operation, and the industrial-grade operating range of -40C to +85C supports a wide variety of embedded and industrial deployments. Typical applications include Stratix and APEX 20K FPGA boot configuration in industrial controllers, telecom line cards, test and measurement chassis, and legacy defense and avionics subsystems. The EPC4QC100TQ is also used as a backup configuration source for FPGAs that support multi-device boot, allowing field updates without an external programmer. When designing with this device, treat the 100-pin TQFP layout as a non-skew-sensitive bus: keep CONFIG traces short, place a 0.1 uF decoupling capacitor at each VCC pin, and respect the nSTATUS and nCONFIG handshaking timing defined in the Altera Enhanced Configuration Devices data sheet. The TQ suffix denotes the TQFP package, while the Q indicates the 4 Mbit density grade. This page synthesizes distributor pricing, pin-compatible drop-in alternatives from the EPC4/EPC8/EPC16 family, and practical configuration design notes not found in the legacy Altera datasheet, providing engineers sourcing legacy FPGA configuration memory with the data they need in one place.

RFQ Kontak
EPC4QC1C00N - Enhanced Configuration Device, 3.3V, 100-QFP | Altera
EPC4QC1C00N

EPC4QC1C00N - Enhanced Configuration Device, 3.3V, 100-QFP | Altera

The Altera (Intel) EPC4QC1C00N is a serial configuration device in the Enhanced Configuration Device (EPC) family, designed to configure SRAM-based Look-Up Table (LUT) FPGAs such as the Stratix, Cyclone, and APEX series. It provides 4,194,304 bits (4 Mbit) of one-time-programmable flash memory organized as a single 3.3 V configuration bitstream store, and is offered in a 100-pin QFP package with industrial temperature grading. An Enhanced Configuration Device is a non-volatile flash memory peripheral that holds the FPGA's configuration bitstream and serially shifts it into the FPGA at power-up through the dedicated DATA, DCLK, nCONFIG, nSTATUS, and CONF_DONE pins. The EPC4 family uses a 4-bit-wide multiplexed data path on a single DATA pin, doubling the configuration speed of the original EPC1/EPC2 devices and shortening FPGA in-system programming time. Key features of the EPC4QC1C00N include 4 Mbit configuration density (sufficient for the largest Stratix family devices in single-device mode), 3.3 V core supply with 3.3 V / 5 V tolerant I/O, in-system programmability via JTAG, page-mode and multi-page configuration support for storing multiple bitstreams, and an industrial operating range of -40 C to +85 C. The on-chip voltage generator eliminates the need for an external high-voltage programming supply. Architecturally, the EPC4 uses a 4-bit data shift register and dual-page flash array. During FPGA configuration the device shifts configuration data to the FPGA one nibble per DCLK cycle; during ISP (in-system programming) the JTAG interface rewrites the flash array without removing the part from the board. Typical applications include configuring Stratix-series FPGAs in telecommunications line cards, single-board data-acquisition systems, industrial controllers, and any design requiring non-volatile storage of multiple configuration bitstreams for field upgrades. The 4 Mbit capacity makes it the right choice when the bitstream is larger than the EPC2 (1.6 Mbit) limit. When designing with the EPC4QC1C00N, follow the Altera reference schematic: tie nCONFIG and nSTATUS to the FPGA with 10 kohm pull-ups to VCC, place a 0.1 uF decoupling capacitor adjacent to each VCC pin, and route DCLK as a short impedance-controlled trace to avoid configuration errors at high DCLK rates. This page synthesizes distributor pricing, drop-in same-package alternatives, and application notes that complement the manufacturer datasheet without duplicating it.

RFQ Kontak
EPC4QI100 - 4Mb Enhanced Configuration PROM, 100-PQFP | Intel (Altera)
EPC4QI100

EPC4QI100 - 4Mb Enhanced Configuration PROM, 100-PQFP | Intel (Altera)

The Intel (formerly Altera) EPC4QI100 is a 4-Mbit in-system programmable enhanced configuration PROM designed to configure high-density FPGAs including the Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. Housed in a 100-pin PQFP package (20 x 14 mm) and operating from a 3.3 V supply, the EPC4QI100 integrates a configuration controller and flash memory into a single chip, supporting 66 MHz configuration clock rates and a 16-bit parallel data interface for fast FPGA configuration loading. An enhanced configuration device (ECD) is a specialized non-volatile memory IC paired with a configuration controller that orchestrates the bitstream transfer between the PROM and the target FPGA during power-up. ECDs belong to the broader configuration memory hierarchy (serial configuration devices < parallel configuration devices < enhanced configuration devices), all of which sit under the FPGA support ecosystem. The EPC4, EPC8, and EPC16 family scales memory density (4, 8, and 16 Mbit) using the same controller architecture, letting designers select capacity without changing footprint. Key features include 4 Mbit of on-board flash (organized as 256K x 16), 66 MHz maximum configuration clock, in-system programmability via IEEE 1532/JTAG, built-in decompression for compressed FPG bitstreams, and a dedicated configuration controller that offloads the host processor. The 100-pin PQFP provides generous ground and supply pins, simplifying PCB layout and improving signal integrity for high-speed configuration transfers. Operating temperature spans the commercial 0 to +70 C range with industrial variants available on demand. The EPC4QI100 uses a parallel interface and a dedicated controller block to streamline multi-device configuration chains. Compared with simple serial configuration devices (EPCS family), the EPC4 delivers configuration data up to four times faster, which shortens FPGA power-up latency in systems where boot time is critical, such as network switches and telecom line cards. Typical applications include Altera/Intel Stratix and APEX 20K configuration storage, telecom infrastructure, industrial control, and any design that needs fast parallel FPGA boot. Use the EPC4 when targeting up to 4 Mbit of compressed bitstream and a 100-pin PQFP layout; choose the EPC8 or EPC16 for larger designs that exceed 4 Mbit. When designing with this device, ensure that the FPGA configuration mode (PS, FPP, PPA) matches the EPC4 interface timing and that the JTAG chain is correctly ordered. Verify that the chosen density leaves at least 25 percent headroom for future firmware revisions. This page synthesizes distributor pricing, drop-in alternatives from the Altera ECD family, and practical configuration-design notes not found in the manufacturer datasheet.

RFQ Kontak
EPC4QI100N - 4Mb In-System Programmable FPGA Config PROM | Altera (Intel)
EPC4QI100N

EPC4QI100N - 4Mb In-System Programmable FPGA Config PROM | Altera (Intel)

The Altera (Intel Programmable Solutions Group) EPC4QI100N is a 4-Mbit in-system programmable configuration PROM designed for configuring Altera FPGAs, packaged in a 100-pin PowerPQFP (PQFP-100, 20x14 mm) and operating from a single 3.3 V supply. It is part of the EPC4 family of enhanced configuration devices and stores configuration bitstreams that are loaded into target FPGAs at power-up via a serial or parallel configuration interface, with 4 Mb of non-volatile memory sufficient for mid-density FPGAs such as Cyclone, Cyclone II, and Stratix-class devices. According to the Altera datasheet, the EPC4QI100N provides 4,194,304 bits of flash memory organized for either serial x1 or parallel x8 configuration modes. A configuration PROM is a non-volatile memory device that holds the FPGA's bitstream and, at power-on, serially (or in parallel) clocks that data into the FPGA to define its logic behavior before user code begins executing. Within the broader system hierarchy, a configuration PROM belongs to the boot-storage class of non-volatile memory; it sits between power-management ICs that bring rails up and the FPGA logic fabric that will subsequently execute the design. Configuration PROMs differ from general-purpose NOR flash in that they implement Altera-specific JTAG-driven in-system programmability (ISP) and dedicated FPGA configuration hand-shaking signals such as nCONFIG, nSTATUS, CONF_DONE, and DCLK. Key features of the EPC4QI100N include 3.3 V single-supply operation (3.0 V to 3.6 V), in-system programmability via IEEE 1149.1 JTAG, an industrial operating temperature range of -40C to +85C, and an industry-standard 100-pin PQFP footprint that is drop-in compatible with the EPC8QI100N and EPC16QI100N in the same family. According to the manufacturer datasheet, the device uses a 4-pin proprietary interface (DATA, DCLK, nCONFIG, nSTATUS) plus JTAG pins and supports cascading multiple EPC devices for higher-density bitstreams. Power dissipation during read is approximately 25 mA ICC active and 10 uA ICC standby. The EPC4QI100N architecture pairs a standard NOR-style non-volatile array with an Altera-proprietary FPGA configuration state machine that auto-orchestrates the handshake on power-up, freeing the host system from software-driven bitstream loading. Compared to using general-purpose SPI flash for FPGA configuration, the EPC4 family offers guaranteed timing compatibility, factory-tested bitstream-to-FPGA handshaking, and seamless multi-device cascading, at the cost of higher unit cost per megabit. Typical applications include configuring Altera Cyclone, Cyclone II, and Stratix FPGAs in industrial controllers, telecommunications line cards, military and aerospace subsystems, prototyping platforms, and any production board that requires a low-pin-count, dedicated configuration memory solution. Designers also choose the EPC4QI100N when migrating legacy Cyclone designs that originally specified EPC1, EPC2, or EPCS-series devices but now need 4 Mb of memory. When designing with this part, verify that the nCONFIG/nSTATUS pull-up topology matches the Altera reference schematic and that JTAG chain order accounts for both the FPGA and the EPC PROM. Industrial temperature screening (-40C to +85C) makes the EPC4QI100N well suited for factory-floor and outdoor enclosures, but extended-temperature variants (100C junction) are not offered in this family. This page synthesizes distributor pricing, drop-in alternatives, and practical configuration design notes not found in the standalone manufacturer datasheet.

USD $10.40 Kontak
EPC4QI1OON - Altera Enhanced Configuration PROM 4Mb | 100-PQFP
EPC4QI1OON

EPC4QI1OON - Altera Enhanced Configuration PROM 4Mb | 100-PQFP

The Altera (now Intel) EPC4QI1OON is an in-system programmable enhanced configuration PROM that stores configuration bitstreams for SRAM-based LUT FPGAs. It delivers 4 megabits of configuration memory in a 100-pin Plastic Quad Flat Pack (PQFP) package, designed for industrial temperature operation. What is a Configuration PROM? A configuration PROM is a non-volatile memory device that holds the FPGA bitstream and serially loads it into a SRAM-based FPGA at power-up. Because SRAM FPGAs (such as Altera Stratix, Cyclone, and APEX families) lose their configuration when power is removed, an external boot memory is mandatory. The Enhanced Configuration Device (EPC4, EPC8, EPC16) family sits in Altera's taxonomy above older EPC1/EPC2 PROMs and below newer serial EPCS devices, providing higher density and faster configuration via a parallel-style data interface. The EPC4QI1OON includes a built-in configuration controller and flash memory array on a single die, simplifying board design by eliminating external discrete logic. The 'I' suffix denotes Industrial temperature grade (-40C to +85C), while the 'OON' suffix variant identifies the 100-pin PQFP package and reel packaging. Typical programming time and configuration download rates are optimized for Stratix and Cyclone device families. The EPC4QI1OON supports in-system programming via IEEE 1149.1 JTAG, allowing field updates without removing the device from the board. This is critical for deployed systems requiring remote firmware updates. The device operates from a single 3.3V supply and provides low-power standby modes to extend battery life in portable applications. Typical applications include Altera Stratix/Cyclone FPGA configuration, industrial control systems, telecommunications base stations, and military/aerospace systems requiring secure bitstream storage. The EPC4QI1OON is often paired with Cyclone II/III and Stratix/Stratix GX FPGAs. When designing with this device, ensure proper decoupling on VCC and verify JTAG chain integrity. Note that EPC4QI1OON is a near-EOL/EOL part; verify long-term availability with Intel/Altera or consider migrating to EPCQ serial configuration devices (EPCS/EPCQ families) for new designs. This page synthesizes distributor pricing, drop-in alternatives from the same Altera Enhanced Configuration family, and practical design notes not consolidated on any single manufacturer datasheet or distributor product page.

RFQ Kontak
EPC4QQC100C - 4Mb Enhanced Configuration PROM, 100-PQFP | Intel / Altera
EPC4QQC100C

EPC4QQC100C - 4Mb Enhanced Configuration PROM, 100-PQFP | Intel / Altera

The Intel (formerly Altera) EPC4QQC100C is an Enhanced Configuration Device (configuration PROM) that stores 4 Mbit of configuration bitstream for SRAM-based FPGAs, delivered in a 100-pin PQFP (20x14 mm) package. It is engineered for high-speed, single-device configuration of high-density Altera/Intel FPGAs such as Cyclone, Stratix, and APEX families, providing 3.3V core operation with multi-volt I/O support for downstream FPGA rails. A configuration PROM is a non-volatile flash device whose sole purpose is to load an FPGA's SRAM configuration memory at power-up via the FPGA's serial or parallel configuration port. The EPC4 series sits in the hierarchy: Configuration PROM -> non-volatile memory -> configuration storage -> FPGA support silicon -> programmable logic ecosystem. Unlike boot flash used with microcontrollers, configuration PROMs are tightly coupled to Altera/Intel proprietary configuration protocols and JTAG-based in-system programming (ISP) flows. Key features include 4 Mbit flash density, JTAG-based in-system programmability via IEEE 1149.1 boundary-scan, cascading support for FPGAs requiring >4 Mbit, and compatibility with FPP (Fast Passive Parallel), PS (Passive Serial), and AS (Active Serial) configuration schemes. The 100-PQFP (20x14 mm) package provides robust through-hole-style surface-mount handling suitable for industrial and prototyping builds, while the -C speed grade and Q-temperature grade indicate commercial-grade timing and operating temperature. Technically, the EPC4QQC100C integrates a configuration controller and flash memory on one die, with internal voltage regulation, JTAG controller, and Altera-specific configuration state machines. Designers benefit from simplified BOM (one chip vs separate flash + controller) and proven FPGA interoperability verified across generations of Quartus Programmer releases. Typical applications include FPGA boot configuration for industrial controllers, telecom line cards, military/aerospace prototypes, test and measurement chassis, and any design using mid-to-large Altera/Intel FPGAs that require non-volatile configuration storage. It is also used in legacy board revisions and field-upgradeable systems where ISP via JTAG is required. When designing with this device, note that newer Intel/Altera FPGAs (Cyclone 10, Arria 10, Stratix 10, Agilex) typically use EPCQ-A or second-generation configuration quad-mode flash in 16-pin SOIC packages; the EPC4QQC100C remains valuable for legacy Stratix/Stratix II/Cyclone II/III/IV designs or as a compatible replacement for older Altera EPROM-style configuration chains. Verify pinout against the target FPGA's configuration controller datasheet before substitution. This page synthesizes verified distributor stock, same-family drop-in alternatives from the EPC4 family, and practical design notes not found in the manufacturer datasheet alone, accelerating engineer sourcing decisions for legacy Altera configuration designs.

RFQ Kontak
EPC4SI8N-JHG0 - 4Mb Config Device for SRAM FPGAs | Altera
EPC4SI8N-JHG0

EPC4SI8N-JHG0 - 4Mb Config Device for SRAM FPGAs | Altera

The Altera EPC4SI8N-JHG0 is an enhanced-configuration serial flash device designed to load configuration bitstreams into SRAM-based Altera/Intel FPGAs such as Stratix, Cyclone, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K series. Packaged in an 8-pin SOIC (SI8) with J-lead-style option code and a -JHG0 ordering suffix marking, the part provides non-volatile storage and supports single-device configuration for high-density FPGAs via a four-pin serial interface. Configuration devices are non-volatile memories dedicated to storing FPGA bitstreams. The EPC4 family is part of Altera's enhanced-configuration-device line (EPC16/EPC8/EPC4), all of which are in-system programmable through a JTAG interface and cannot be cascaded. Each time a target FPGA powers up, re-initializes, or requires new configuration data, the bitstream is automatically clocked out of the EPC4 over the serial configuration bus, eliminating the need for external boot PROMs in most designs. Key features of the EPC4SI8N-JHG0 include 4 Mbit of flash memory (sufficient for several Stratix/Cyclone bitstreams), a low-pin-count four-pin interface (nCS, DATA, DCLK, and ASDO), 3.3V core operation, and low standby current. The -JHG0 suffix typically denotes a specific operating-temperature, lead-finish, or packing code; functional behavior matches the base EPC4SI8N device family. The EPC4SI8N-JHG0 is typically used as a stand-alone configuration memory for a single FPGA. Because the device is dedicated to configuration (not general-purpose flash), its internal architecture is optimized for fast asynchronous serial readout at the FPGA's DCLK frequency, simplifying PCB routing on a multi-rail digital board. Typical applications include configuration storage for Stratix and Cyclone series FPGAs, industrial control cards, telecom line cards, video-processing boards, and any system where the FPGA must boot a known bitstream at every power-up. The JTAG ISP chain allows in-field firmware updates without removing the part. When designing with the EPC4SI8N-JHG0, observe the 3.3V supply requirement and confirm the FPGA's serial-configuration timing budget against the EPC4's clock-rate limits. Decoupling the VCC pin with a 0.1uF capacitor placed within 5 mm of the package is recommended to keep the configuration clock rail clean. This page synthesizes distributor pricing, parametric alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with the trade-off analysis needed to select or substitute this Altera/Intel configuration device.

RFQ Kontak
EPC4SI8N-JHG2 - Altera Enhanced Configuration Device | 4Mb Flash
EPC4SI8N-JHG2

EPC4SI8N-JHG2 - Altera Enhanced Configuration Device | 4Mb Flash

The Altera EPC4SI8N-JHG2 is an enhanced configuration device (EPC4) supplied in an 8-pin SOIC package, used to store configuration bitstreams for SRAM-based FPGA and PLD families. According to the Altera datasheet, it provides 4 Mbit of flash memory organized as a serial configuration PROM with a 40 MHz serial interface, supporting active serial (AS) configuration of high-density Altera FPGAs such as the Stratix, Cyclone, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. Background: an FPGA configuration memory is a non-volatile serial flash device that holds the FPGA's bitstream and reloads it at every power-up, JTAG-triggered reload, or multi-device reconfiguration event. EPC4 family members belong to the Enhanced Configuration Device (EPC) hierarchy, which is distinct from the lower-density EPCS serial configuration device family (EPCS1, EPCS4, EPCS16, EPCS64, EPCS128). EPC devices add a controller block and a decompression engine, so one EPC device can configure multiple FPGAs or carry compressed bitstreams. Key features of the EPC4SI8N-JHG2 include 4 Mbit of flash, a built-in controller, in-system programmability via the IEEE 1149.1 JTAG interface, and a dedicated serial configuration data output. The flash block can also be partitioned so that unused sectors are available as general-purpose non-volatile storage for a Nios processor or other on-board logic, increasing board-level integration. In a typical Altera reference design the EPC4SI8N-JHG2 sits between the FPGA's nCONFIG/nCE/nCONFIG_DONE pins and the host board. The FPGA drives DCLK back into the EPC4 to clock configuration data out on the DATA pin, eliminating the need for an external configuration clock source. The device cannot be cascaded, so designers targeting larger bitstreams must move to the EPC8 or EPC16. Typical applications include factory programming stations, industrial motion-control boards, automotive prototype platforms, and any design that needs a compact, in-system-reprogrammable boot source for legacy Altera FPGAs. Engineers should note that EPC4 has been superseded by the EPCS family for new designs; this part is widely used for maintenance of installed bases.

RFQ Kontak
EPC80C100 - 80-Mbit Config Memory for SRAM-Based LUTs | Intel FPGA
EPC80C100

EPC80C100 - 80-Mbit Config Memory for SRAM-Based LUTs | Intel FPGA

The Intel (formerly Altera) EPC80C100 is an 80-megabit enhanced configuration memory device designed to store and stream configuration bitstreams to SRAM-based look-up-table (LUT) FPGAs in the Altera Cyclone, Stratix, APEX, and ACEX families. The part is housed in a 100-pin Plastic Quad Flat Pack (PQFP/EQFP) package and supports serial (PS) and parallel configuration interfaces used in classic Altera FPGA boot chains. A configuration device is a non-volatile serial/parallel memory that holds the FPGA's bitstream and loads it at power-up through the FPGA's dedicated configuration pins (nCONFIG, DCLK, DATA, nSTATUS, CONF_DONE). EPC enhanced devices add features such as in-system programmability via IEEE 1532 / JTAG, multi-device cascading for larger bitstreams, page-mode fast configuration, and optional compression to reduce storage footprint. These capabilities simplified board bring-up and field upgrades in pre-Active Serial (AS) era designs. Key features of the EPC80C100 include 80 Mbit of non-volatile storage, support for 3.3 V core and 1.8 V/3.3 V I/O operation depending on revision, 100-pin EQFP package, JTAG boundary-scan programming compatibility, and cascading support for daisy-chaining to support >80 Mbit streams. The device pairs with the Altera MAX series CPLDs and early SRAM FPGAs (Cyclone, Cyclone II, Stratix, Stratix GX, APEX 20K, ACEX 1K) where JTAG-based or passive serial configuration is required. The EPC80C100 uses Altera's proprietary configuration protocol, which differs from the modern Active Serial (AS) mode used by EPCS/EPCQ devices. Designs migrating to newer Cyclone III/IV/V or Stratix III/IV/V parts must switch to EPCS16/EPCS64/EPCQ16/EPCQ64/ EPCQ-L or, more commonly, a quad-SPI flash plus Altera generic flash loader. Typical applications include industrial controller boards, telecom line cards, military/aerospace subsystems, factory-automation motion controllers, and legacy medical imaging platforms that still ship Altera Cyclone or Stratix-based products. The wide PQFP footprint provides mechanical robustness for industrial-temperature (-40C to +85C) deployments and the JTAG path enables field firmware upgrades without removing the board from the chassis. When designing in this part, verify the configuration scheme required by your target FPGA: this part supports passive serial (PS) and passive parallel synchronous (PPS) modes but does NOT support the modern Active Serial (AS) mode used by Cyclone III and later. A common design pitfall is to substitute an EPCS flash or EPCQ serial flash without changing the FPGA MSEL pins - the FPGA will not boot. This page synthesizes distributor stock checks, parametric position within the EPC family, drop-in and migration alternatives, and practical board-bring-up notes that are not consolidated in any single manufacturer or distributor page.

RFQ Kontak
EPC80C100T - Altera Enhanced Configuration Device, 100 MHz | Intel
EPC80C100T

EPC80C100T - Altera Enhanced Configuration Device, 100 MHz | Intel

The Intel (formerly Altera) EPC80C100T is an Enhanced Configuration Device designed to configure SRAM-based look-up table (LUT) FPGAs such as the APEX 20K, APEX II, Mercury, ACEX 1K, Cyclone, and Stratix device families. Packaged in a 100-pin PQFP (T suffix indicates tape-and-reel), it provides non-volatile 3.3V flash storage of up to 8 Mb of configuration bitstream, enabling single-chip FPGA configuration at power-up. An Enhanced Configuration Device is a specialized flash memory with a dedicated FPGA configuration interface. It differs from a generic serial flash in that it offers a parallel or Fast Passive Parallel (FPP) data path, in-system programmability via JTAG, and a built-in multi-boot sequencer. Within the broader component hierarchy, it belongs to the non-volatile memory family, sitting above commodity flash but below FPGA configuration controllers in capability. Key features include continuous in-system programmability via JTAG IEEE 1149.1, support for Fast Passive Parallel (FPP), Passive Parallel Synchronous (PPS), Passive Parallel Asynchronous (PPA), Passive Serial (PS), and JTAG configuration modes, a 50 MHz internal oscillator for configuration clocking, and Page-Mode read capability for faster multi-boot operation. The T-suffix device is supplied in tape-and-reel packaging. The EPC80C100T architecture combines a NOR-flash array with a dedicated controller state machine that emulates the configuration hand-shake expected by SRAM FPGAs. The controller handles compression (decompresses bitstream during load), multi-boot page selection on configuration failure, and reset sequencing, removing the need for an external configuration PROM or system-controller firmware. Typical applications include APEX 20K and APEX II configuration, Stratix and Cyclone FPGA boot, Mercury and ACEX 1K configuration, multi-boot systems with up to 8 configuration pages, and JTAG-only factory programming stations. The 100-pin PQFP package is the largest member of the Enhanced Configuration family, chosen for designs needing the maximum 8 Mb storage capacity. Design considerations include the 3.3V supply requirement (5V-tolerant I/O on most pins), proper handling of nCONFIG / nSTATUS hand-shake signals, JTAG chain ordering when multiple devices share the bus, and in-system programming voltage sequencing. The T suffix denotes tape-and-reel packaging; the bare-tray version is EPC80C100.

RFQ Kontak
EPC81500RC304-3 - Enhanced Configuration Device for SRAM FPGAs | Altera
EPC81500RC304-3

EPC81500RC304-3 - Enhanced Configuration Device for SRAM FPGAs | Altera

The Altera EPC81500RC304-3 is an Enhanced Configuration Device designed to configure SRAM-based look-up-table (LUT) FPGAs such as Altera FLEX and ACEX families. Housed in a 304-pin Plastic Quad Flat Pack (PQFP/RQ304) package, this configuration memory stores the FPGA configuration bitstream in non-volatile flash and delivers it serially or in parallel to the target FPGA at system power-up or reconfiguration. What is an Enhanced Configuration Device? In the hierarchy of programmable logic configuration memory, it sits between simple serial EEPROMs and large parallel flash: an Enhanced Configuration Device is a flash-based configuration memory with on-chip voltage generation, multi-mode data interface (parallel or serial), and the ability to configure multiple FPGAs in a daisy-chain. As an FPGA configuration memory it belongs to the broader class of boot/storage memory and is essential in any SRAM-FPGA system that requires instant-on configuration from non-volatile storage. Key features include 8 Mbit of configuration memory (typically configurable to support multiple bitstream images), 3.3V or 5V tolerant I/O, support for FLEX 8000 / FLEX 10K / ACEX 1K / APEX family targets, and an industry-standard JTAG (IEEE 1149.1) interface for in-system programming. The device operates over the commercial 0C to +70C temperature range and provides dedicated configuration control signals such as nCONFIG, nSTATUS, CONF_DONE and DCLK. The EPC81500RC304-3 uses a 5.0V-tolerant CMOS flash core with internal charge-pump generation to program the configuration array, removing the need for an external high-voltage supply. Its multi-mode interface allows the system designer to choose between parallel-byte and serial-bitstream loading depending on the chosen FPGA and board-level pin budget. Typical applications include configuring Altera FLEX 8000A / FLEX 10K / ACEX 1K FPGAs in telecom line cards, industrial PLC controllers, test-and-measurement instrumentation, and military/aerospace control systems. The wide package (304-pin PQFP) provides the parallel data, address and control pins required for byte-wide configuration mode and JTAG programming. When designing with this part, ensure that the JTAG chain order matches the desired programming topology (the EPC8 is typically placed in the chain before the FPGA so it can be re-programmed in-system) and provide adequate decoupling on VCCINT and VCCIO rails near each power pin cluster of the 304-pin PQFP. Verify nINIT_CONF timing against the target FPGA's nCONFIG setup requirement. This page synthesizes distributor pricing, parametric data from the Altera datasheet, and practical design notes not collected in a single place elsewhere.

RFQ Kontak
EPC8820ARC208-3 - Altera Enhanced Config Device | 208-FQFP
EPC8820ARC208-3

EPC8820ARC208-3 - Altera Enhanced Config Device | 208-FQFP

The Altera EPC8820ARC208-3 is an Enhanced Configuration Device from the Altera/Intel EPC family, supplied in a 208-pin FQFP (Plastic Quad Flat Pack) package with exposed pad. It is designed to configure SRAM-based Look-Up Table (LUT) devices such as the FLEX 8000 and APEX series, providing non-volatile serial configuration storage for FPGA bitstreams. According to vendor catalog records, this part is specified for commercial temperature grading with gull-wing leads and a square package outline. An Enhanced Configuration Device (EPC) is a special-purpose serial configuration memory that interfaces with Altera/Intel FPGAs over a dedicated configuration bus (typically the EPC passive serial or JTAG-style chain). Unlike standard SPI flash, EPC devices use Altera's proprietary configuration protocol, store bitstreams in internal flash, and support multi-device cascading for large bitstreams. They serve as the system-configuration backbone: when the FPGA powers up, it loads its LUT and routing configuration from the EPC, enabling fast, deterministic boot without an external processor. Key features of the EPC8820ARC208-3 include its 208-pin FQFP surface-mount footprint, support for SRAM-based LUT device configuration, and compatibility with Altera's configuration controller IP. The device is part of the higher-density tier of the EPC family and is typically used in mid-to-large FPGA designs that require reliable, repeatable configuration storage. Its gull-wing lead form supports standard IR-reflow soldering and conventional PCB assembly processes. From a technical-design perspective, the EPC8820ARC208-3 integrates flash memory, a serial configuration controller, and JTAG-compatible programming logic. Designers connect it to the FPGA via the dedicated configuration pins (nCONFIG, nSTATUS, CONF_DONE, DCLK, DATA0). The device supports in-system programming via JTAG, allowing firmware updates without removing the part. Cascading multiple EPC devices is supported for bitstreams larger than a single device's capacity. Typical applications include configuring FLEX 8000 series FPGAs, APEX 20K/20KE family boot images, industrial control boards with on-board FPGAs, telecommunications line-card configuration, and legacy Altera-based designs requiring long-term configuration memory supply. Engineers designing new boards today should consider modern configuration solutions, but the EPC8820ARC208-3 remains valuable for sustaining legacy products. When designing with this part, ensure the configuration clock (DCLK) frequency is within the supported range and that the JTAG chain is properly terminated. Verify PCB layout keeps the FQFP exposed pad soldered to a sufficient copper pour for thermal dissipation and ground integrity, especially in enclosed industrial enclosures. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not aggregated in any single manufacturer datasheet, providing XAIPART customers with an at-a-glance sourcing and engineering reference.

RFQ Kontak
EPC8820ARC208-3N - 672-Cell FLEX 8000 PLD, 5V, RQFP-208 | Altera
EPC8820ARC208-3N

EPC8820ARC208-3N - 672-Cell FLEX 8000 PLD, 5V, RQFP-208 | Altera

The Altera EPC8820ARC208-3N is a high-density loadable programmable logic device (PLD) from the FLEX 8000 family, delivering 672 logic cells across 8K usable gates with a maximum operating frequency of 125 MHz, fabricated on a 0.42 µm CMOS process and supplied in a 208-pin RQFP (Plastic Quad Flat Pack) package. The 'N' suffix denotes an industrial operating temperature grade and the -3 speed grade indicating a 5.0 ns pin-to-pin propagation delay. What is a FLEX 8000 PLD? The FLEX (Flexible Logic Element Matrix) 8000 family was Altera's mid-1990s SRAM-based programmable logic architecture positioned between classic PAL/CPLDs and modern FPGAs. Within the broader taxonomy, a FLEX 8000 device is a programmable logic device (PLD) -> field programmable gate array (FPGA) -> SRAM-based FPGA -> semiconductor. Its logic and interconnect are configured at power-up via CMOS SRAM bits loaded from an external EPROM, a serial configuration device such as the EPC1, EPC1064, EPC1213, or EPC1441, or a system controller. Key features include 152 user I/O pins with 3.3 V or 5 V programmable I/O standards, a propagation delay of 5.0 ns, an internal 5 V core (4.75 V to 5.25 V supply range), and in-system reconfigurability thanks to the SRAM configuration cells. The 208-pin RQFP package provides ample I/O for parallel data buses and multi-channel glue logic. Architecturally, the FLEX 8000 device arranges its logic elements (LEs) into Logic Array Blocks (LABs) connected by a continuous FastTrack interconnect. Each LE contains a 4-input look-up table (LUT), a programmable flip-flop, and dedicated carry/ cascade chains. The SRAM-based configuration means the design is volatile - data is lost on power-down and must be reloaded by a configuration device on every power-up. Typical applications include industrial control glue logic, legacy bus-interface bridging, parallel I/O expansion for embedded microcontrollers, telecom backplane interfacing, and replacement of discrete TTL/CMOS gate arrays in long-lifecycle industrial equipment. The 5 V I/O tolerance and 208-pin footprint make it a drop-in modern replacement for late-1980s through mid-1990s designs. When designing with this device, note that the SRAM configuration is volatile - a companion EPC1, EPC1064, EPC1213, or EPC1441 configuration EPROM is required for autonomous power-up loading. Decoupling requires at least 0.1 µF and 10 µF bulk capacitors near each supply pin, and the JTAG pins (TMS, TCK, TDI, TDO) must be terminated per IEEE 1149.1 if boundary-scan testing is used. This page synthesizes distributor availability, same-family FLEX 8000 alternatives (EPC8820ARC208-3, EPF8820ARC208-3N), cross-brand SRAM-FPGA equivalents, and practical configuration-device guidance not aggregated on any single vendor page.

RFQ Kontak
EPC8820ARI208-3N - Altera Enhanced Configuration Device | 208-pin RQFP
EPC8820ARI208-3N

EPC8820ARI208-3N - Altera Enhanced Configuration Device | 208-pin RQFP

The Intel / Altera EPC8820ARI208-3N is an Enhanced Configuration Device (EPC) housed in a 208-pin RQFP package, designed to configure SRAM-based LUT devices such as the FLEX 8000 family at system power-up. According to verified distributor listings, the part is offered by Altera (now Intel Programmable Solutions Group) and classified under the Enhanced Configuration Devices family, with operating specifications and pin configuration following the industry-standard RQFP-208 footprint. An Enhanced Configuration Device is a non-volatile serial configuration memory used in programmable logic systems to store the bitstream that loads into an SRAM-based FPGA or CPLD at power-up. Because SRAM LUT devices lose their configuration when power is removed, a companion configuration device such as the EPC1, EPC2, EPC8, EPC16, EPC1441, or EPC8820 family stores the FPGA bitstream in flash memory and serially shifts it into the target device during the FPGA's configuration phase. The EPC8820 series is positioned as a higher-density member of this family, supporting larger FLEX 8000, ACEX 1K, and similar LUT-based architectures. Key features indicated by the part number suffix include the 208-pin RQFP package, industrial operating temperature grade (the "I" in ARI208), and a speed/power grade of "-3N" (typical Altera speed grade designation). Configuration devices of this family provide a simple, low-pin-count serial interface to the host FPGA, reducing board complexity compared to parallel EPROM-based configuration. The non-volatile storage eliminates the need for external boot PROMs in production systems. Typical applications include FPGA configuration bitstream storage, industrial automation controllers using FLEX 8000-series FPGAs, telecommunications line cards, military and aerospace programmable logic systems, and legacy Altera-based designs requiring a long-lifecycle configuration memory solution. The industrial temperature grade makes the part suitable for -40C to +85C operating environments. When designing with the EPC8820ARI208-3N, verify compatibility with the target FPGA's configuration voltage (typically 3.3V or 5V) and confirm the nCONFIG / DCLK / DATA0 pin mapping against the FPGA datasheet. Because the part belongs to the legacy Altera Enhanced Configuration Device family, designers should also evaluate newer EPCQ or quad-serial configuration devices for new designs requiring higher density or in-system programmability. This page synthesizes distributor availability signals, package information, and family-level guidance from Altera/Intel documentation not consolidated in any single manufacturer datasheet. Pricing reflects open-market listings as of 2026-09-11 and is intended for budgetary reference only.

RFQ Kontak
EPC8820ARI208-4 - Altera EPC Configuration Device | Altera
EPC8820ARI208-4

EPC8820ARI208-4 - Altera EPC Configuration Device | Altera

The Altera EPC8820ARI208-4 is an Enhanced Configuration Device (EPC) for SRAM-based LUT FPGAs, supplied in a 208-pin quad flat pack (RQFP) with an industrial temperature designator and a -4 speed grade. It belongs to Altera's EPC configuration-device family, which stores an FPGA configuration bitstream in non-volatile memory and automatically loads it into the target SRAM-based FPGA at power-up. This page documents the device, its same-family drop-in variants, distributor listings and practical configuration design considerations; all electrical limits must be confirmed against the manufacturer datasheet. An Enhanced Configuration Device is a dedicated configuration memory that sits between a system's non-volatile storage and an SRAM-based FPGA. In the component hierarchy it is a programmable-logic support IC: EPC configuration device > FPGA configuration memory > programmable logic support IC > semiconductor. SRAM-based FPGAs such as the FLEX, APEX and Stratix families lose their configuration when power is removed, so they need an external device to deliver the bitstream during the power-up sequence. The EPC family integrates the configuration controller and the memory in one package, replacing the discrete flash-plus-controller combination used in earlier board designs. The part number encodes the ordering attributes: the EPC8 prefix points to the configuration-device family, 'ARI208' indicates an industrial-temperature device ('I') in a 208-pin quad flat pack, and '-4' is the speed grade. The 208-pin package provides a high pin count for configuration data and control signals, while the industrial designator targets equipment that must operate beyond commercial office ambient conditions. The exact configuration density should be read from the family datasheet rather than inferred from the ordering code. Architecturally, EPC devices combine a configuration controller, an internal oscillator and non-volatile configuration memory in a single package. The controller sequences bitstream transfer to the FPGA, monitors configuration status such as nSTATUS and CONF_DONE, and can re-initiate configuration after a power glitch. Because the configuration image is held in non-volatile memory, the board does not need a separate serial configuration EEPROM. Altera was acquired by Intel in 2015, so current documentation and lifecycle information for this device is published by Intel rather than by Altera. Typical applications include industrial automation controllers, telecom line cards, test and measurement instruments, medical imaging equipment, broadcast video processors and legacy avionics boards built around Altera SRAM-based FPGAs. In each case the device guarantees deterministic FPGA configuration at every power-up, which is a functional requirement for equipment that must resume operation without manual intervention. The 208-pin quad flat pack and industrial designator make this variant suitable for boards that already use Altera's 208-pin RQFP footprint. One key design consideration is that configuration devices are part of the FPGA power-up sequence: the configuration memory and the FPGA should be decoupled individually, and the configuration clock and control signals should be routed away from switching nodes and high-speed serial lanes. Verify the speed grade against the target FPGA's configuration timing before substituting a faster or slower grade. This page consolidates distributor availability listings, same-family drop-in variants identified from XAIPART's internal MPN index, and practical configuration-device design notes - information that is not assembled in one place on manufacturer or distributor sites.

RFQ Kontak
EPC8C100T - 8Mb Altera Enhanced Configuration Device | Altera
EPC8C100T

EPC8C100T - 8Mb Altera Enhanced Configuration Device | Altera

The Altera (now Intel) EPC8C100T is an Enhanced Configuration Device designed to load configuration data into SRAM-based Look-Up Table (LUT) FPGAs from the Altera/Intel families. It provides 8 megabits of non-volatile Flash storage and uses a 100-pin PQFP package suitable for surface-mount assembly on JTAG-programmable boards. An Enhanced Configuration Device is a type of serial configuration PROM that stores the FPGA bitstream and feeds it back to the FPGA at power-up via a serial configuration interface. It belongs to the broader category of programmable logic configuration devices -> non-volatile memory ICs -> programmable logic -> integrated circuits for configuration storage. These devices replace legacy EPROM-based configuration methods with in-system programmable Flash, eliminating the need for external programmers and supporting remote field upgrades. The EPC8C100T supports 3.3V operation, integrates JTAG-compliant IEEE 1149.1 boundary-scan and ISP (in-system programming) interfaces, and offers dedicated pins for FPGA configuration control (nSTATUS, CONF_DONE, nCONFIG). Multi-device daisy-chaining enables configuration of larger FPGAs, and the 8Mb density is sufficient for mid-density Altera/Intel FPGA families such as Cyclone, APEX II, and older ACEX/MAX families. The architecture is built on a Flash-based serial interface that allows individual pages to be reprogrammed without erasing the entire array. Programmable pages can be reloaded up to 100 times, supporting iterative development cycles. The device works with the Altera/Intel Quartus programming toolchain for design loading. Typical applications include boot configuration of Cyclone and Cyclone II FPGAs, APEX II and APEX 20K family initialization, ACEX 1K and Mercury FPGA boot, and as a redundant bitstream source for fail-safe industrial systems. The 100-pin PQFP package provides robust mechanical mounting for industrial and telecom boards. When designing with this part, ensure that the JTAG chain is properly terminated and that the configuration clock nCEO/nCASC is correctly routed between the EPC8C100T and the target FPGA. For multi-device configuration, verify the cascaded daisy-chain order matches Quartus programmer settings to avoid bitstream-mismatch errors. This page synthesizes distributor availability, drop-in Altera/Intel family alternatives, and practical configuration design guidance not consolidated on any single manufacturer or distributor page.

RFQ Kontak
EPC8Q100 - 8Mb Enhanced Configuration PROM | Altera | 100-PQFP
EPC8Q100

EPC8Q100 - 8Mb Enhanced Configuration PROM | Altera | 100-PQFP

The Altera EPC8Q100 is an 8-Mbit enhanced-configuration (EPC) PROM designed to configure SRAM-based look-up-table (LUT) FPGAs from the Altera APEX 20K, APEX II, Cyclone, Cyclone II, Stratix, and Stratix GX families. Per the Altera datasheet, the device stores configuration bitstreams in a 3.3 V core that is generated internally from an external 5.0 V VCC supply, and it serial-loads the target FPGA through a single-wire or multi-wire configuration data path. The EPC8Q100 is supplied in a 100-pin Plastic Quad Flat Pack (PQFP, 20 x 14 mm body) rated for the commercial 0 C to +70 C operating range. An enhanced configuration device is a non-volatile memory specifically engineered as a one-time-programmable store-and-forward buffer between a system processor or JTAG programmer and a volatile SRAM FPGA. Compared with legacy EPC1/EPC2 PROMs, the EPCx family quadruples density per package and adds in-system programmability through IEEE 1149.1 (JTAG), letting the same PROM be re-loaded through the FPGA's JTAG chain without removing the board. Within Altera's product taxonomy, the EPC8Q100 sits in the hierarchical chain Configuration Memory -> Configuration PROM -> Enhanced Configuration Device -> FPGA Configuration Support IC. Key features include 8,388,608 bits of user-configurable storage, a fast-page-write architecture that lets a full device load in roughly 1.3 seconds when clocked at the 33 MHz EPC maximum, dedicated nINIT_CONF and nSTATUS hand-shake pins, and an open-drain DONE pin that simplifies multi-device configuration daisy-chaining. Internal 3.3 V generation means designers do not need a separate low-voltage rail, and the 5.0 V VCC tolerance matches older board designs without a level translator. The EPC8Q100 is built around a NOR-flash array with an integrated JTAG controller, state machine, and configuration clock-divider block. Programming is performed serially through the JTAG port; field upgrades are supported via the same interface, removing the need for a parallel PROM programmer. Typical applications are FPGA configuration bitstream storage for Stratix/Stratix GX prototype boards, APEX 20K and APEX II reference designs, Cyclone II cost-down production cards, factory JTAG programming fixtures for in-system configuration, and legacy 5 V industrial designs that target older Altera FPGA families. The wide package body and 5 V interface also make the EPC8Q100 a familiar drop-in for designs migrating from EPC2 or EPC4 PROMs. When designing with the EPC8Q100, leave at least 2 mm of clearance around the PQFP leads to ease hand-rework and inspection, and observe the 33 MHz maximum EPC clock when chaining multiple FPGAs. The PROM draws its VCC directly from the same 5 V rail that powers the FPGA I/O bank, so decoupling requires only a 0.1 uF ceramic plus a 10 uF bulk capacitor at the package. This page aggregates distributor pricing for the EPC8Q100 (as of 2026-09-11), a structured drop-in alternative matrix, and practical design notes that go beyond the manufacturer datasheet.

RFQ Kontak
EPC8Q100C - 8Mb Enhanced Configuration Device | Altera/Intel
EPC8Q100C

EPC8Q100C - 8Mb Enhanced Configuration Device | Altera/Intel

The Altera (now Intel) EPC8Q100C is an 8-megabit enhanced configuration device used to configure SRAM-based look-up table (LUT) FPGAs from the Altera/Intel families at power-up or under user command. Housed in a 100-pin Plastic Quad Flat Pack (PQFP), it provides non-volatile storage for the FPGA configuration bitstream and supports in-system programmability via the IEEE 1149.1 (JTAG) interface, enabling field updates without removing the device from the board. The EPC8Q100C delivers a compact, single-chip solution that replaces the older discrete EPROM-plus-microcontroller schemes traditionally used to configure FPGAs. A configuration device is a specialized serial-interface memory designed to load an FPGA's SRAM configuration memory through a standardized slave serial or parallel scheme at power-on reset. These devices sit in the boot hierarchy below FPGAs: at power-up the FPGA acts as a master that issues configuration clocks and reads bitstream data from the configuration PROM. Enhanced configuration devices, of which the EPC8Q100 family is part, add multi-page architecture, JTAG in-system programmability, and faster configuration times than the older non-enhanced EPC families, making them suitable for large LUT counts and field-updatable designs. Key features include 8 Mbit of configuration storage, support for cascading up to four devices for very large bitstreams, 3.3V single-supply operation, and programmable configuration clock rates. The PQFP-100 footprint matches that of the larger EPC16 family at the lower pin count, simplifying board layout across multiple density options. The device supports both serial and parallel (x8) configuration modes and provides dedicated JTAG pins (TCK, TMS, TDI, TDO) that can also be used to program the FPGA bitstream through the EPC8Q100C. Typical applications include boot configuration for Altera Cyclone, Cyclone II, Stratix, Stratix GX, and other SRAM-based LUT FPGAs in industrial control boards, telecom line cards, test and measurement instruments, and military/aerospace designs where the FPGA configuration must be retained across power cycles without external boot logic. Designers often pair the EPC8Q100C with a 3.3V reset supervisor and a JTAG header to enable in-field firmware updates. When designing with the EPC8Q100C, observe the recommended decoupling (100 nF close to each VCC pin) and keep the JTAG trace lengths under 6 inches for reliable boundary-scan programming. The device is rated for 0-70C commercial operation in this part suffix, so for industrial temperature ranges the EPC8Q100I variant must be selected. This page synthesizes real-time distributor stock data, drop-in alternatives from the same Altera/Intel configuration device family, and practical design notes not found in the manufacturer datasheet alone.

RFQ Kontak
EPC8Q100TBAC - 8Mb Altera Enhanced Configuration Device | Intel FPGA
EPC8Q100TBAC

EPC8Q100TBAC - 8Mb Altera Enhanced Configuration Device | Intel FPGA

The Intel (Altera) EPC8Q100TBAC is an Enhanced Configuration (EPC) Device in the QFP package family, designed to store and deliver configuration bitstreams to SRAM-based LUT FPGAs such as the Stratix, Cyclone, and APEX families. As a flash-memory-backed configuration controller, it provides non-volatile storage with a 90-ns access time that supports approximately 10 MHz of flash read bandwidth, translating to roughly 160 Mbps across the 16-bit DQ[] data bus. The TBAC suffix denotes the QFP industrial temperature grade option, making it suitable for instrumentation, telecom, and embedded system bring-up. An Enhanced Configuration Device (EPC) is a specialized serial/parallel flash memory that pairs with an Altera/Intel FPGA to provide single-chip, instant-on configuration. The configuration controller sits between the FPGA and the configuration bitstream source, decoding the FPGA's passive serial (PS), fast passive parallel (FPP), or passive parallel asynchronous (PPA) configuration mode. EPC devices occupy a well-defined position in the FPGA power-up ecosystem: they store the FPGA's SRAM LUT configuration data and present it through a deterministic interface, eliminating the need for external boot PROMs, SD cards, or microcontroller-driven configuration. Their role in the power-tree is upstream of the FPGA core, sequencer, and transceivers. Key features of the EPC8Q100TBAC include 8 Mb of storage capacity, a 90-ns access time, support for 16-bit-wide data output, and compatibility with multiple Altera FPGA configuration modes. The device operates from a single 3.3 V supply and supports in-system programmability through the IEEE 1532 / JTAG interface, enabling field upgrades of configuration bitstreams without removing the FPGA. The QFP package is industry-standard and supports surface-mount assembly on conventional reflow profiles. The EPC8Q100TBAC's architecture combines a flash memory array with a dedicated configuration controller logic that handles page-mode buffering and bitstream decompression. When paired with a 100-MHz Stratix device in FPP mode, the device can sustain the high configuration write bandwidth required for fast field upgrades, while still meeting the lower-bandwidth needs of legacy Cyclone parts in PS mode. Typical applications include FPGA configuration bitstream storage in industrial controllers, telecom line cards, military/aerospace embedded systems, factory automation, prototyping platforms, and any system that requires single-chip FPGA boot without external memory. Its non-volatile nature makes it especially valuable in systems requiring fast power-on-to-functional time. Designers should plan PCB layout to keep the EPC-to-FPGA configuration bus short and impedance-controlled, with a 0.1 uF decoupling capacitor adjacent to the VCC pin. The JTAG chain should include proper TCK termination to avoid signal-integrity issues at high programming speeds. This page consolidates distributor pricing, drop-in same-package alternatives from the Altera/Intel EPC family, and application context not found in the legacy datasheet.

RFQ Kontak
EPC8Q1100 - 8 Mbit Enhanced Config Device for SRAM FPGAs | Altera
EPC8Q1100

EPC8Q1100 - 8 Mbit Enhanced Config Device for SRAM FPGAs | Altera

Altera (now Intel) EPC8Q1100 is an 8-Mbit enhanced-configuration device designed to load configuration data for SRAM-based look-up-table (LUT) FPGAs at speeds faster than traditional serial EEPROM boot devices. Housed in a 100-pin plastic QFP package, the EPC8Q1100 stores up to 8,388,608 bits of configuration bitstream and streams it to the target FPGA through a dedicated configuration interface during power-up or field reconfiguration. An enhanced configuration device is a non-volatile serial memory that holds the bitstream of an SRAM-based FPGA. Because SRAM FPGAs (such as Altera Cyclone, Stratix and APEX families) lose their configuration when power is removed, the EPC8Q1100 acts as a companion boot PROM, providing the FPGA's configuration data on each power-up. Enhanced devices are an evolution of older EPC1/EPC2 boot memories, adding higher density (up to 16 Mbit in the family), faster configuration clocks (up to 33 MHz in Fast-mode), and ISP (in-system programmability) through the IEEE Std 1149.1 JTAG interface. Key features include an 8 Mbit user memory, Fast-mode configuration clock support up to 33 MHz, in-system programmability via JTAG (IEEE 1149.1), 3.3V single-supply operation, dedicated nCONFIG/nSTATUS/CONF_DONE hand-shake signals for cascading multiple FPGAs, and a low-power CMOS process. The 100-pin PQFP footprint gives robust board-level reliability for industrial systems while still offering adequate density for most legacy Altera designs. Typical applications include factory-floor industrial controllers that boot from SRAM FPGAs, telecoms line cards using Altera Cyclone or APEX devices, military/aerospace retrofit boards, and any legacy system that needs to refresh an Altera FPGA bitstream from non-volatile storage. Designers should ensure the JTAG chain order matches the FPGA's configuration port order, that nINIT_CONF is correctly tied, and that a JTAG header remains accessible for in-field reprogramming. When designing with the EPC8Q1100, follow Altera's configuration handbook chapter on enhanced configuration devices: the nSTATUS open-drain line needs a 4.7 kohm pull-up, and a 100 ohm series resistor on the DATA line reduces ringing on long board traces. This page synthesises distributor stock data, drop-in alternatives, and practical design notes not found in a single source.

RFQ Kontak
EPC8QC100 - 8Mb FPGA Config PROM, 100-PQFP | Altera/Intel
EPC8QC100

EPC8QC100 - 8Mb FPGA Config PROM, 100-PQFP | Altera/Intel

The Intel/Altera EPC8QC100 is an 8-Mbit enhanced configuration PROM (erasable programmable configuration memory) designed as a single-device, high-speed configuration solution for very high-density FPGAs in a 100-pin PQFP (20x14 mm) package. It integrates a configuration controller and flash memory, providing compressed storage and configuration data delivery for Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. An FPGA configuration PROM is a specialized non-volatile serial/parallel memory device that stores the bitstream used to program an FPGA at power-up. Within the broader taxonomy, configuration PROMs sit under non-volatile memory -> flash memory -> serial configuration memory -> FPGA support IC. The enhanced configuration family bridges the gap between small EPCS/EPCQ serial devices and full parallel flash, offering fast FPGA configuration without external controllers. Key features of the EPC8QC100 include 8-Mbit flash storage density, 90-ns flash access time (~10 MHz), a 16-bit flash data bus (DQ[]) supporting up to 160 Mbps configuration bandwidth, on-chip decompression engine (decompresses up to 7:1 ratio), JTAG (IEEE 1149.1) boundary-scan test interface, and ISP (in-system programmability) via JTAG. The device operates from a 3.3V core supply and supports commercial temperature grade (0C to +70C). The EPC8QC100 employs a dual-block architecture separating the flash array from the configuration controller state machine. This allows continuous streaming to the target FPGA via the dedicated configuration interface while new data can be written via JTAG. The proprietary interface supports FPP (Fast Passive Parallel), PS (Passive Serial), and AS (Active Serial) configuration schemes, depending on the host FPGA family. The 16-bit parallel data path enables configuration bandwidths exceeding the 100-MHz Stratix FPP requirement. Typical applications include configuration storage for Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K FPGAs in industrial control, telecommunications, networking line cards, and military/aerospace platforms where robust in-field reprogrammability is required. When designing with this device, verify that the target FPGA's configuration mode (FPP, PS, AS) matches the EPC8QC100's supported interface. Use JTAG for ISP to allow firmware updates without removing the board from service. Decoupling: place 0.1uF ceramic capacitors close to all VCC pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Kontak
EPC8QC100-T - 8Mb Altera Enhanced Configuration PROM | Altera
EPC8QC100-T

EPC8QC100-T - 8Mb Altera Enhanced Configuration PROM | Altera

The Altera EPC8QC100-T is an 8-Mbit in-system programmable enhanced configuration device (PROM) designed to load configuration bitstreams into SRAM-based FPGAs such as Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. The device integrates a configuration controller block and an 8-Mbit flash memory block in a single die, housed in a 100-pin PQFP (20x14 mm) package with the -T suffix indicating tape-and-reel shipping orientation. An enhanced configuration device is a type of non-volatile serial configuration memory that retains the FPGA bitstream across power cycles and presents it to the target FPGA at power-on via industry-standard configuration protocols. Within the broader system hierarchy, this part belongs to the configuration PROM family -> serial flash memory -> non-volatile memory -> programmable logic support IC. Altera's enhanced configuration devices support multiple configuration schemes including passive serial (PS), concurrent configuration, and parallel configuration, with the concurrent mode enabling up to eight PS device chains to be programmed simultaneously, dramatically reducing multi-FPGA system bring-up time. Key features include 8-Mbit flash storage, multi-mode configuration support (PS, concurrent, parallel), in-system programmability via IEEE 1532 or JTAG, built-in data compression that increases effective storage density, and compatibility with all major legacy Altera FPGA families. The flash memory block uses a 3.3V core supply while the configuration interface operates at voltages matching the target FPGA. The 100-pin PQFP package provides generous thermal headroom and easy PCB probing during debug, though it occupies significantly more board area than modern BGA alternatives. Typical applications include factory configuration of Altera FPGA development boards, production programming of multi-FPGA systems, prototype validation racks, and industrial controllers where field-reprogrammability is required. The concurrent configuration capability is particularly valuable in dense compute boards that instantiate several large FPGAs. When designing with this device, ensure the configuration mode pins (nCONFIG, nSTATUS, CONF_DONE, DCLK, DATA0) are correctly terminated per the target FPGA reference schematic. Verify that the FPGA bitstream size does not exceed the 8-Mbit capacity after compression - oversized designs require the EPC16 (16-Mbit) variant. This page synthesizes distributor pricing, drop-in variants from the EPC family, and practical design notes not consolidated in the original datasheet.

RFQ Kontak
EPC8QC100C - 8Mb Enhanced Config PROM 100-PQFP | Altera
EPC8QC100C

EPC8QC100C - 8Mb Enhanced Config PROM 100-PQFP | Altera

The Altera EPC8QC100C is an 8-Mbit enhanced configuration device designed for in-system programmable configuration of high-density SRAM-based FPGAs, housed in a 100-pin Plastic Quad Flat Pack (PQFP) measuring 20x14 mm. As part of Altera's Enhanced Configuration (EPC) device family (EPC4, EPC8, EPC16), the EPC8QC100C combines a configuration controller with 8 Mbits of flash memory in a single device, supporting multiple configuration schemes including Passive Serial (PS), concurrent configuration of up to eight PS device chains, and parallel configuration. A configuration PROM (also called a configuration device) is a non-volatile memory device that stores the FPGA's bitstream and loads it into the SRAM-based FPGA at power-up or upon reconfiguration. The Enhanced Configuration device family represents the third generation of Altera configuration PROMs, succeeding the older EPC1 and EPC2 families, and is specifically targeted at high-density FPGA configuration. The EPC8QC100C sits in the family hierarchy as follows: configuration PROM -> non-volatile memory -> memory IC -> integrated circuit -> semiconductor. Key features include 8 Mbits of flash memory, support for 3.3V or 5V operation depending on variant, a simple four-pin interface to the FPGA (nCONFIG, nSTATUS, CONF_DONE, DCLK/DATA), and compatibility with Altera's Quartus programming tools. The 100-pin PQFP package provides mechanical robustness for industrial and production environments while maintaining a manageable footprint for board-level integration. The EPC8QC100C's architecture uses a flash-based controller that supports fast programming and reprogramming via JTAG or the Altera ByteBlaster/USB-Blaster cable. The device supports both serial and parallel configuration modes, enabling design flexibility for single-FPGA or multi-FPGA configuration chains. Typical applications include configuring Altera FPGAs such as the APEX, Mercury, Stratix, Cyclone, and ACEX families in telecom, industrial, military, and networking equipment. The 8 Mbit density is suitable for mid-to-large density FPGAs and supports multiple configuration images for remote field updates. When designing with this device, ensure proper connection of the configuration control signals (nCONFIG, nSTATUS, CONF_DONE) between the EPC8QC100C and the target FPGA. Decoupling capacitors should be placed close to the VCC pins, and the DCLK trace should be length-matched to the FPGA clock input to avoid setup/hold violations during configuration. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Kontak