Mga Produkto (46,000+)

LM224KNE4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM224KNE4

LM224KNE4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM224KNE4 is a quadruple operational amplifier built around four high-gain, internally frequency-compensated amplifiers. The device operates from a single power supply, supports supply voltages up to 30 V, and provides a gain-bandwidth product of 1.2 MHz per amplifier. It is packaged in a 14-pin PDIP and rated for operation from -25°C to +85°C, making it suitable for general-purpose industrial and instrumentation signal-processing circuits. An operational amplifier is a high-gain analog building block used to amplify small voltage signals, buffer sensors, implement active filters, and drive higher-impedance loads. The LM224 belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and integrated analog signal-processing ICs. Its four amplifiers share a power supply while operating independently, allowing one package to implement several stages of a signal chain while conserving PCB area. The LM224KNE4 provides a 1.2 MHz gain-bandwidth product, a 30 V maximum supply capability, and approximately 3 mV typical input-offset voltage. Typical input-offset current is 2 nA, while input-bias current is approximately 20 nA. The device also offers improved 2 kV ESD protection. These characteristics support accurate closed-loop amplification when appropriate external feedback and compensation components are selected according to the manufacturer's application guidance. The four amplifiers are internally frequency compensated, simplifying basic gain configurations without requiring external compensation in ordinary closed-loop operation. The LM224 series supports operation from a single supply, and its common-mode input range includes ground, which is useful for signals referenced to the lower supply rail. Low input-bias and input-offset currents also reduce errors when the source impedance is relatively high. Typical uses include sensor-signal conditioning, process-control instrumentation, active analog filtering, low-frequency audio and communications circuitry, and general industrial control systems. Because the package contains four amplifiers, applications such as instrumentation amplifiers, multi-stage filters, bridge amplifiers, and four-channel signal-conditioning boards can reduce both component count and board space. Input and output signal ranges must remain within the electrical limits for the selected supply voltage. For reliable PCB implementation, follow the manufacturer pinout and place input, output, and supply connections to minimize noise pickup and unwanted oscillation. Keep sensitive input traces short, provide adequate decoupling across the supply pins, and avoid placing high-impedance signal routes beside fast-switching nodes. Stable feedback-network layout is particularly important when the amplifier operates near its 1.2 MHz gain-bandwidth product. This product summary combines the manufacturer device information, ordering details, distributor listings, and documented cross-reference results into an engineering-oriented view of the LM224KNE4. It also identifies same-footprint alternatives, highlights parameter differences, and adds practical guidance for power bypassing, input routing, feedback layout, and replacement qualification.

RFQ Kontak
LM224M - Quad 32V Op Amp in 14-SOP | onsemi
LM224M

LM224M - Quad 32V Op Amp in 14-SOP | onsemi

The onsemi LM224M is a general-purpose quad operational amplifier packaged in a 14-pin SOP. Each amplifier provides true differential inputs, internal frequency compensation for unity gain, a large DC voltage gain of 100 dB, and a wide 3 V to 32 V power-supply range. The M suffix identifies the 14-SOP package, while the broader LM224 family is intended for operation from 3 V to 32 V. The input common-mode voltage range includes ground, and the output can swing from approximately 0 V to VCC minus 1.5 V. An operational amplifier is an analog signal-processing semiconductor that uses differential feedback to amplify the voltage difference between its two inputs while rejecting common-mode signals. The LM224M belongs to the hierarchy of operational amplifier, analog amplifier, linear integrated circuit, and semiconductor. Its internally compensated architecture allows stable operation as a unity-gain buffer without external frequency-compensation components, simplifying sensor, control, and signal-conditioning circuits. Key features include four amplifiers in one package, true differential inputs, a 100 dB DC voltage gain, unity-gain frequency compensation, and supply operation from 3 V to 32 V. The ground-referenced input range is useful for battery-powered and single-supply systems in which signals remain near zero volts. Output swing ending near VCC minus 1.5 V should be considered when designing logic-level interfaces or driving heavier loads. The LM224M is suitable for general-purpose industrial analog systems operating across a wider temperature range than commercial-grade LM324 variants, although the exact temperature limits and electrical limits must be confirmed from the selected manufacturer datasheet. It can provide input buffering, sensor amplification, error amplification, and low-frequency closed-loop signal conditioning when operated with suitable passive feedback networks. Typical uses include temperature-sensor interfaces, process-control loops, current-sensing amplifiers, low-level transducers, instrumentation, and embedded analog subsystems. In a sensor circuit, the LM224M can amplify a small differential signal while its feedback network sets the closed-loop gain. In a control loop, it can amplify an error voltage while avoiding external compensation components, subject to stability and noise checks in the completed circuit. When designing around the LM224M, keep input and feedback components close to the relevant pins, provide suitable supply bypassing, and verify the input common-mode range under every supply condition. Avoid assuming rail-to-rail input or output capability. The documented input range includes ground, but does not necessarily extend to the positive supply rail. Likewise, the maximum output swing is not equal to the positive rail because the specified upper limit is approximately VCC minus 1.5 V. This product page synthesizes the verified LM224M package, supply-range, gain, compensation, input-range, and output-swing information with practical design guidance and source traceability. The included comparisons and alternatives are limited to parts that can be evaluated as same-package drop-in options; verify pinout, electrical limits, temperature range, and production status before substitution.

RFQ Kontak
LM224N - Quad 32V 1.2MHz Op Amp | Texas Instruments
LM224N

LM224N - Quad 32V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM224N is a quad operational amplifier with a 32 V supply rating, 1.2 MHz gain-bandwidth product, four amplifier circuits, and a 14-pin PDIP package. Designed for general-purpose signal conditioning, the LM224N supports single-supply operation and is positioned for applications requiring multiple amplifiers on one package. According to the TI product page, the LM224-N family is a general-purpose quad amplifier solution. An operational amplifier is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. LM224 devices contain four independently usable amplifiers, allowing one package to implement sensing, buffering, amplification, filtering, or control functions. The LM224N family is commonly associated with single- and dual-supply operation, making it relevant to industrial control, instrumentation, sensor interfaces, and low-frequency analog signal chains. The LM224N combines four amplifiers, a 32 V maximum supply rating, and a 1.2 MHz bandwidth in one 14-pin PDIP package. The verified distributor listing identifies the device as a standard general-purpose amplifier with four circuits and a 14-PDIP package. Its quad configuration can reduce component count and board area in designs that need several similar amplifier stages. The LM224N is intended for general-purpose analog applications where a conventional high-voltage-capable op amp is appropriate. Its internally compensated architecture makes it useful for non-inverting and inverting amplifier stages, voltage followers, comparators, and basic active-filter stages when the circuit requirements fall within the datasheet limits. The package and electrical details should be checked against the selected manufacturer datasheet before layout release. Typical applications include sensor signal conditioning, industrial process monitoring, instrumentation amplifiers, current-voltage conversion, audio and communications support circuits, and embedded control systems. Using four amplifiers in one package is especially useful when several channels need similar conditioning characteristics, such as monitoring multiple sensor inputs. Designers should verify supply voltage, input common-mode range, output swing, offset voltage, slew rate, stability, and temperature limits against the applicable datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be configured according to the manufacturer recommendations rather than left floating. This page combines the verified Texas Instruments and distributor data with practical package, application, sourcing, and replacement guidance. It distinguishes confirmed facts from parameters that require verification against the full manufacturer datasheet, helping engineers evaluate the LM224N without relying on assumptions.

RFQ Kontak
LM224NG - Quad 3-32V Op Amp, 14-PDIP | onsemi
LM224NG

LM224NG - Quad 3-32V Op Amp, 14-PDIP | onsemi

The onsemi LM224NG is a quad general-purpose operational amplifier designed for single-supply operation from 3.0 V to 32 V. It contains four true differential-input amplifier sections in a 14-pin PDIP package and is specified for an operating temperature range of -25°C to +85°C. The device is intended for instrumentation, buffering, amplification, and general analog signal-chain applications where a single supply simplifies system power architecture. An operational amplifier, or op amp, is an analog integrated circuit that uses high-gain differential amplification to control an output voltage. The LM224 belongs to the general-purpose op-amp class within the broader voltage-amplifier and signal-conditioning hierarchy. Its four amplifier channels make it useful when a design requires multiple analog functions in one package, reducing board area compared with four separate single or dual amplifier packages. The LM224NG provides a 1 MHz gain-bandwidth product and a slew rate of 0.6 V/µs. These values position the device for low-frequency signal conditioning rather than high-speed pulse or video amplification. The four channels support true differential inputs, allowing common-mode input voltage and input bias current to be considered during sensor-interface and instrumentation design. The listed operating characteristics are suitable for general-purpose amplifier, buffer, and comparator-style circuit arrangements. The 14-pin PDIP package provides through-hole mechanical compatibility and straightforward prototyping. Because the package has no exposed thermal pad, heat dissipation depends on the PCB or socket thermal path and the total dissipation of the four channels. The 3 V to 32 V supply range covers 5 V, 12 V, 24 V, and 32 V rails commonly found in industrial control, consumer electronics, instrumentation, and embedded systems. Single-supply operation also makes zero-crossing and ground-referenced signal conditioning easier to implement. Typical uses include sensor buffering, transducer signal conditioning, low-frequency active filtering, current-to-voltage conversion, test equipment, and control-system analog front ends. Designers should check input common-mode limits, output swing, supply current, stability, and noise requirements for the selected gain and load. The LM224NG is not a precision op amp, so applications requiring very low offset, drift, or noise should compare the device with a higher-accuracy family. This page combines the LM224NG electrical characteristics, package data, sourcing guidance, and application-oriented design notes into a practical engineering reference. Use the manufacturer datasheet for the definitive pin descriptions, maximum ratings, and test conditions before committing the part to a high-voltage or high-reliability design.

RFQ Kontak
LM224NG4 - Quad 1.2MHz Op Amp | Texas Instruments
LM224NG4

LM224NG4 - Quad 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM224NG4 is a general-purpose, four-circuit operational amplifier with a 1.2 MHz gain-bandwidth product, supplied in a 14-pin dual in-line package. The four amplifiers are internally frequency compensated and can operate independently, making the device suitable for general signal-conditioning, instrumentation, and control applications. The package supports through-hole PCB assembly in a 0.300-inch, 7.62 mm pitch DIP format. An operational amplifier is an analog signal-processing IC that amplifies the difference between its inverting and non-inverting inputs. Its high open-loop gain, negative-feedback operation, and internal compensation allow it to function as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style interface, or active filter building block. The LM224NG4 belongs to the broad operational-amplifier hierarchy within analog and linear integrated circuits. The key headline specifications are four amplifier circuits in one package, a 1.2 MHz gain-bandwidth product, and a 14-pin DIP package. The LM224 family is designed for operation from a single supply or split supplies, with a documented supply-voltage range of 3 V to 32 V. This combination supports economical industrial, instrumentation, sensor, and test-equipment designs where four general-purpose amplifiers are needed on one board. The quad organization reduces component count and PCB area compared with four separate single operational amplifiers. Each amplifier has independent inverting and non-inverting inputs, an output, and a power connection, allowing unused amplifier sections to be configured according to standard feedback arrangements. Internal frequency compensation removes the need for an external dominant-pole capacitor in typical closed-loop uses. Typical applications include low-frequency instrumentation amplifiers, transducer-signal conditioning, current-to-voltage conversion, sensor interfaces, sample-and-hold stages, active filtering, and general industrial control. The 1.2 MHz gain-bandwidth product is most suitable for low-to-moderate-frequency signal paths rather than high-speed video or RF amplification. Users should also account for input common-mode range, output swing, input bias current, and supply-current limits when defining the usable signal range. For a new 14-pin DIP design, verify the pin arrangement and operating limits in the manufacturer datasheet before layout. Place bypass capacitors close to the supply pins, keep sensitive inverting-input traces short, and connect unused amplifier inputs to a defined potential rather than allowing them to float. Thermal design should consider the dissipation from all four amplifiers and the maximum ambient and junction temperatures permitted for the purchased package variant. This page combines the verified LM224NG4 device identity with application guidance, drop-in comparison criteria, package considerations, and design notes that help engineers evaluate the part before committing it to a 14-DIP board layout.

RFQ Kontak
LM224PT - Quad 1.3MHz Op Amp | STMicroelectronics
LM224PT

LM224PT - Quad 1.3MHz Op Amp | STMicroelectronics

STMicroelectronics LM224PT is a four-amplifier general-purpose operational-amplifier IC with a 1.3 MHz gain-bandwidth product, 0.4 V/µs slew rate, and 14-TSSOP package. The four amplifiers are independent and internally frequency compensated, allowing each channel to be used separately for signal conditioning, voltage amplification, or analog calculations. The device supports single-supply operation from 3 V to 30 V and split-supply operation up to ±15 V. An operational amplifier is an analog integrated circuit that compares an inverting input with a non-inverting input and drives its output toward the difference between them, multiplied by a very high open-loop gain. In the signal-chain hierarchy, the LM224PT belongs to the operational-amplifier class, then to the broader amplifier IC and analog signal-conditioning categories. Its internally compensated architecture simplifies use in voltage followers, buffers, transimpedance stages, differential amplifiers, comparators, and basic control loops. Key characteristics include four independent amplifiers, a 1.3 MHz gain-bandwidth product, a 0.4 V/µs slew rate, low input bias current, and operation from a broad single supply. These characteristics make the part suitable for industrial control, sensor interfaces, audio preamplification, and low-frequency analog systems. Internal frequency compensation removes the need for an external compensation network in ordinary closed-loop applications. The wide operating-voltage range allows one device family to serve 5 V, 12 V, 15 V, 24 V, and ±15 V systems when the circuit and output-swing limits permit. As a low-power general-purpose amplifier, it prioritizes supply flexibility, moderate bandwidth, and low input bias current rather than rail-to-rail operation, high slew rate, or low-noise precision performance. Designers should check input common-mode range, output swing, input differential voltage, and supply-current limits against the actual circuit. Typical applications include buffering sensor outputs, amplifying low-frequency control signals, conditioning potentiometer inputs, driving analog stages in industrial equipment, and implementing general feedback control. The four-channel configuration can reduce the number of packages in multichannel analog boards while preserving independent operation and grounding flexibility. Layout should keep input and feedback traces short, place input-biasing components close to their pins, and maintain a quiet return path to minimize parasitic pickup. Decoupling capacitors should be placed at the supply pins, while unused amplifier channels should be configured in a stable state rather than left floating. This page combines the manufacturer-device identity, package information, operating characteristics, drop-in replacement research, and application-specific design guidance. It is intended to help engineers evaluate LM224PT quickly, compare it with compatible devices, and implement it correctly without treating a general-purpose amplifier as a precision or rail-to-rail part.

RFQ Kontak
LM239AD - Quad Open-Collector Comparator | Texas Instruments
LM239AD

LM239AD - Quad Open-Collector Comparator | Texas Instruments

Texas Instruments LM239AD is a quad differential comparator in a 14-pin SOIC package, designed for level detection, low-level sensing, memory applications, and general-purpose signal conditioning. The device contains four independent voltage comparators with open-collector outputs. The verified product information identifies the LM239 as a commercial-grade comparator family and the LM239A as a precision quad differential comparator for industrial applications. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. Within the semiconductor hierarchy, the LM239AD belongs to the comparator, analog IC, and signal-conditioning categories. Unlike a digital logic gate, the comparator evaluates continuously varying analog voltages and is commonly placed at the boundary between sensors, transducers, reference circuits, and digital control systems. The principal product attributes are four independent comparator channels, differential inputs, open-collector outputs, and a 14-pin SOIC package. Open-collector outputs require an external pull-up resistor to establish a usable high voltage. This arrangement allows the output to be pulled to an external supply, supports wired-AND behavior when multiple comparators share a node, and provides compatibility with TTL, CMOS, and MOS logic when the pull-up voltage and sink-current limits are selected correctly. Each channel compares an inverting input with a non-inverting input. The open-collector transistor pulls the output low when the non-inverting input is below the inverting input and releases the output when that relationship reverses. Because the four sections are independent, they can evaluate different thresholds in one package, reducing component count in multilevel sensing, window-detection, and control systems. The open-collector architecture also prevents the comparator from driving a supply rail directly, which is useful in systems with multiple voltage domains. Typical uses include industrial sensor interfaces, automotive battery and system monitoring, consumer threshold detection, memory-cell sensing, and logic-level translation. In a battery monitor, the comparators can establish several voltage thresholds against an external reference. In a memory system, they can detect charge or voltage levels with minimal external circuitry. Their independent channels also make the device suitable for four-limit or four-zone monitoring where separate comparator decisions are required. Designers should verify the exact input common-mode range, supply-voltage limits, input-offset voltage, response time, output sink current, and electrical characteristics against the manufacturer datasheet before finalizing a design. Place the pull-up resistor close to the output node, maintain the device within its rated common-mode input range, and account for input bias current when using high source impedances. Decoupling and unused-channel handling should follow the device recommendations in the manufacturer documentation. This page combines the LM239AD product identity, comparator operating principle, package information, sourcing guidance, drop-in alternatives, comparison points, and practical application guidance. It is intended to help engineers identify the correct channel count, output architecture, package, and operating limits before integrating the device into analog-control or sensing equipment.

RFQ Kontak
LM239ADT - Quad Precision Comparator | STMicroelectronics
LM239ADT

LM239ADT - Quad Precision Comparator | STMicroelectronics

The STMicroelectronics LM239ADT is a four-channel precision differential comparator with an open-collector output, an input offset voltage specified as low as 2 mV maximum, and operation from 2 V to 32 V. It is packaged in a 14-pin SOIC and supplied in tape-and-reel form. The device contains four independent comparators, allowing a single component to implement four threshold, level, or sensing functions. A differential voltage comparator is an analog semiconductor that compares two input voltages and changes its output state according to their relationship. The LM239ADT belongs to the comparator hierarchy within analog integrated circuits and interface signal-conditioning systems. Its open-collector outputs can sink current from a pull-up network while placing the output state partly under the system designer’s control, making the device suitable for wired logic, relay interfaces, and industrial sensing systems. The principal features are four independent channels, a 2 mV maximum offset voltage for the A-grade device, a 2 V to 32 V supply range, and compatibility with CMOS, DTL, ECL, MOS, TTL, and other standard logic families. The open-collector architecture supports wired-AND behavior when multiple comparator outputs share a pull-up resistor. These characteristics are particularly useful where low-level sensor signals must be converted into a digital decision with adjustable thresholds. The LM239ADT is intended for single or dual supply operation, allowing the common-mode range to include ground. Differential input protection is generally required when the input voltages can exceed the supply rails or create large transients. Because the outputs are open collector, an external pull-up resistor is required to establish a valid high level. The output sink current, propagation delay, input bias current, and common-mode limits must be checked against the timing and logic requirements of the complete circuit. Typical applications include industrial control and measurement, sensor threshold detection, battery and power-supply monitoring, window comparison, level detection, and four-channel alarm supervision. In each case, the 2 mV maximum input offset provides useful resolution near the comparison threshold, while independent channels reduce component count. The broad supply range also permits operation from low-voltage analog rails through substantially higher industrial supply voltages, subject to absolute maximum limits. A key design consideration is the pull-up network on the open-collector outputs. Its resistance must provide adequate output rise time without excessive sink current, and its voltage must remain compatible with the connected logic family. Input filtering, hysteresis, and supply-bypass capacitors should be placed close to the device to control noise and unstable switching near the threshold. Care is also required during power-down because the open-collector output can remain high-impedance when the device is unpowered. This product page combines device classification, comparison data, drop-in candidates, application guidance, and practical implementation notes. The accompanying tables help engineers evaluate the LM239ADT against pin-compatible options while keeping the original SOIC-14 footprint and open-collector interface as the central design constraints.

RFQ Kontak
LM239AN - Quad Differential Comparator | STMicroelectronics
LM239AN

LM239AN - Quad Differential Comparator | STMicroelectronics

The STMicroelectronics LM239AN is a low-power quad differential voltage comparator containing four independent comparator channels in a 14-pin through-hole DIP package. The device supports single-supply operation, has a typical input bias current of 25 nA, and belongs to the LM139/LM239 family designed for level detection, low-level sensing, memory, consumer, automotive, and industrial applications. A voltage comparator is an analog semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. The LM239AN belongs to the hierarchy differential comparator, comparator, analog integrated circuit, and semiconductor. Its four independent channels make it suitable for threshold detection, window monitoring, alarm generation, sensor conditioning, and general digital-interface control. The open-collector outputs can also be used to drive wired logic buses when an appropriate pull-up arrangement is provided. Key characteristics include four independent differential comparators, single-supply operation, a 25 nA typical input bias current, an offset voltage specification as low as 2.0 mV maximum for the LM139 series, and open-collector outputs compatible with CMOS, DTL, ECL, MOS, and TTL according to distributor product information. The 14-DIP package provides through-hole assembly compatibility and ample spacing for inspection and hand soldering. The LM239AN architecture supports independent comparison channels within one package, reducing component count in multi-threshold systems. Because the comparators are independent, their input and output nodes are not internally tied together. Designers must observe the common-mode input range and supply-voltage limits from the manufacturer datasheet, especially when comparing signals that can approach either supply rail. Open-collector outputs require suitable pull-up resistors when a valid high output is required. Typical applications include industrial control systems, automotive sensing interfaces, battery-powered equipment, memory threshold detection, consumer electronics, and precision logic interfaces. Four channels can implement separate overvoltage, undervoltage, temperature, and light-level decisions, while open-collector outputs support alarm aggregation or level translation. Low input bias current is particularly useful when the comparator is driven by high-impedance sensors. When laying out a circuit, keep sensitive input traces away from switching nodes and connect each comparator's supply and ground pins with short, low-impedance paths. Confirm input polarity, common-mode limits, output pull-up values, and input-overvoltage conditions against the manufacturer datasheet before releasing a production design. A single supply is convenient, but dual-supply operation may also be possible within specified limits. This product guide combines device specifications, pin assignments, practical application guidance, and drop-in replacement information to accelerate engineering review. It also highlights the electrical and qualification checks required when substituting another quad comparator on an existing 14-DIP PCB.

RFQ Kontak
LM239D - Quad Open-Collector Comparator, 14-SOIC | Texas Instruments
LM239D

LM239D - Quad Open-Collector Comparator, 14-SOIC | Texas Instruments

The Texas Instruments LM239D is a quad open-collector differential comparator IC with four independent precision voltage comparators, a ±15 V or 30 V supply capability, and a 14-pin SOIC package. The verified product data identifies it as a general-purpose comparator intended for level detection, low-level sensing, and memory applications across consumer, automotive, and industrial equipment. Its low-power architecture and open-collector outputs make it useful where multiple comparator channels must interface with pull-up-based logic systems. What is a voltage comparator? A comparator is an analog interface IC that compares two input voltages and changes its output state according to their relationship. The LM239 belongs to the comparator hierarchy: voltage comparator → differential comparator → quad analog comparator → semiconductor. Each channel is independent, allowing one package to perform four separate sensing or threshold decisions. An open-collector output can sink current while remaining electrically disconnected from the positive supply, requiring an external pull-up when a logic-high output is needed. Key verified features include single or split-supply operation, low input bias current of 25 nA typical, and low input offset current of ±5.0 nA typical. The device supports TTL, MOS, CMOS, DTL, and ECL-compatible outputs. The manufacturer’s related LM239 family page identifies the B-version family as a drop-in replacement for LM239, LM339, and LM2901 families, while also noting improved offset voltage, supply current, propagation delay, and ESD performance for the B versions. The LM239D is appropriate for industrial threshold detection, battery monitoring, sensor signal conditioning, window comparators, control loops, and embedded logic interfaces. In a single-supply circuit, the common-mode input range includes ground, which is useful for low-voltage sensing. In split-supply operation, the differential input range can extend up to the maximum-rated supply span, but the complete electrical limits must be taken from the manufacturer datasheet before final design sign-off. The principal design consideration is output polarity and pull-up implementation. Because the outputs are open collector, four external or shared pull-up networks may be required, and their resistor values determine rise time, power dissipation, and compatibility with downstream logic. Input protection, supply bypassing, and unused-channel handling should also follow the datasheet guidance. This page combines verified product specifications, sourcing information, application guidance, and explicitly qualified replacement analysis for LM239D engineers.

RFQ Kontak
LM239DG - 3-36V Quad Comparator | onsemi | SOIC-14
LM239DG

LM239DG - 3-36V Quad Comparator | onsemi | SOIC-14

The onsemi LM239DG is a single-supply quad analog comparator with four independent comparison channels, a 3 V to 36 V supply range, and CMOS, open-collector, TTL-compatible outputs in a 14-pin SOIC package. Its 130 mV typical low-output saturation voltage at 4 mA supports straightforward interface with digital logic, while its low 25 nA typical input bias current and ±5 nA typical input offset current help preserve the accuracy of high-impedance sensing circuits. A quad analog comparator is a multi-channel semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM239DG belongs to the comparator hierarchy within analog and mixed-signal integrated circuits, where it is used for voltage thresholding, signal conditioning, and protection functions. Its four channels share one package but operate independently, allowing a compact design to implement several sensing points without using four separate comparator devices. Key features include four general-purpose comparator elements, single-supply operation from 3 V to 36 V, support for ±1.5 V to ±18 V dual-supply rails, and outputs compatible with CMOS, open-collector, and TTL loads. The typical input offset voltage is listed as no more than 1.3 mV, while the typical input bias current is 25 nA. These characteristics make the device suitable for precision threshold detection where input current must not materially disturb a high-impedance source. The comparator architecture translates the voltage relationship between each noninverting and inverting input into an open-collector output state. Because the outputs are open collector, external pull-up resistors are required for normal logic-high operation. Each output can sink the stated 130 mV typical saturation voltage at a 4 mA load. This arrangement provides flexible voltage-level adaptation, although pull-up selection, output rise time, and system fanout must be considered during design. Typical applications include consumer and industrial level detection, low-level sensing, memory-device threshold monitoring, automotive interface circuits, and general-purpose signal conditioning. The four channels can monitor separate sensor lines, compare a control signal against adjustable references, or implement window-detection functions using external resistor networks. The 3 V minimum supply also permits operation from regulated 5 V or 12 V systems, while the 36 V maximum supports higher-voltage industrial rails when the input and output limits permit. The principal design consideration is protecting every input and output from voltages outside the device ratings, especially during power sequencing. Place the pull-up resistor close to each open-collector output, route sensitive input traces away from switching nodes, and verify logic thresholds against the actual pull-up voltage. A common 14-Pin SOIC footprint also simplifies assembly, but the obsolete lifecycle status requires lifecycle confirmation before committing a new production design. This product page combines the LM239DG electrical characteristics, package details, replacement analysis, and practical design guidance with direct quotations and procurement requests routed through the XAIPART Request a Quote form. It helps engineers evaluate a legacy comparator without relying on incomplete distributor summaries.

RFQ Kontak
LM239DR - Quad Open-Collector Comparator, 14-SOIC | Texas Instruments (Tape & Reel)
LM239DR

LM239DR - Quad Open-Collector Comparator, 14-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments LM239DR is a quad open-collector differential comparator IC with four independent precision voltage comparators, a ±15 V or 30 V supply capability, and a 14-pin SOIC package. The verified product data identifies it as a general-purpose comparator intended for level detection, low-level sensing, and memory applications across consumer, automotive, and industrial equipment. Its low-power architecture and open-collector outputs make it useful where multiple comparator channels must interface with pull-up-based logic systems. What is a voltage comparator? A comparator is an analog interface IC that compares two input voltages and changes its output state according to their relationship. The LM239 belongs to the comparator hierarchy: voltage comparator → differential comparator → quad analog comparator → semiconductor. Each channel is independent, allowing one package to perform four separate sensing or threshold decisions. An open-collector output can sink current while remaining electrically disconnected from the positive supply, requiring an external pull-up when a logic-high output is needed. Key verified features include single or split-supply operation, low input bias current of 25 nA typical, and low input offset current of ±5.0 nA typical. The device supports TTL, MOS, CMOS, DTL, and ECL-compatible outputs. The manufacturer’s related LM239 family page identifies the B-version family as a drop-in replacement for LM239, LM339, and LM2901 families, while also noting improved offset voltage, supply current, propagation delay, and ESD performance for the B versions. The LM239DR is appropriate for industrial threshold detection, battery monitoring, sensor signal conditioning, window comparators, control loops, and embedded logic interfaces. In a single-supply circuit, the common-mode input range includes ground, which is useful for low-voltage sensing. In split-supply operation, the differential input range can extend up to the maximum-rated supply span, but the complete electrical limits must be taken from the manufacturer datasheet before final design sign-off. The principal design consideration is output polarity and pull-up implementation. Because the outputs are open collector, four external or shared pull-up networks may be required, and their resistor values determine rise time, power dissipation, and compatibility with downstream logic. Input protection, supply bypassing, and unused-channel handling should also follow the datasheet guidance. This page combines verified product specifications, sourcing information, application guidance, and explicitly qualified replacement analysis for LM239DR engineers.

RFQ Kontak
LM239DR2G - Quad 36V Open-Collector Comparator | onsemi
LM239DR2G

LM239DR2G - Quad 36V Open-Collector Comparator | onsemi

The onsemi LM239DR2G is a single-supply quad comparator with four independent differential input channels, a 3 V to 36 V supply range, and open-collector outputs. The device provides a typical input offset voltage of 5 mV, typical input bias current of 250 nA, and typical propagation delay of 1.3 microseconds in a 14-pin SOIC package rated for -25 C to +85 C operation. A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM239 belongs to the comparator hierarchy, alongside open-collector and CMOS-compatible interface circuits used for level detection, low-level sensing, and memory applications. Four integrated channels allow one package to perform threshold detection, window monitoring, overvoltage detection, or relay-driving functions. The open-collector outputs can sink current from multiple compatible loads while the output transistor remains off, allowing the designer to select an external pull-up resistor and establish the output logic voltage independently of the comparator supply. This architecture is compatible with TTL, CMOS, and MOS loads, while the 36 V maximum supply rating supports higher-voltage industrial and consumer systems. The typical 1.3 microsecond propagation delay is suitable for general-purpose signal comparison rather than high-speed timing applications. Each channel contains a differential input stage and a discrete output stage. The two inputs of a channel should be connected so that the non-inverting input receives the signal to be detected and the inverting input receives the reference threshold, or vice versa when an inverted output is required. With an open-collector output, the output state is not valid until the external pull-up resistor establishes the high level, so timing calculations must include the pull-up network and any attached load capacitance. Typical applications include industrial control and automation, battery-powered monitoring, power-supply fault detection, sensor threshold conditioning, and memory or system supervision. The quad channel count is especially useful when a board must monitor several rails or compare multiple sensor signals against independently generated references. The wide supply range also permits operation from regulated 5 V, 12 V, and 24 V systems within the stated device ratings. For PCB design, place the pull-up resistor close to each open-collector output and route the comparator inputs away from switching nodes and high-current switching paths. Input bias current of 250 nA typical and 5 mV typical offset make resistor-divider design sensitive to source impedance. Verify that the selected pull-up network does not exceed the output sink-current capability and that the SOIC footprint matches the chosen temperature and packing variant. This page combines manufacturer and distributor component information with a pin-level application guide, drop-in replacement analysis, and practical design notes. It also identifies which electrical characteristics are confirmed for the LM239DR2G and where a design engineer must consult the full manufacturer datasheet before releasing a production schematic.

RFQ Kontak
LM239DRG3 - Quad Differential Comparator | Texas Instruments
LM239DRG3

LM239DRG3 - Quad Differential Comparator | Texas Instruments

Texas Instruments LM239DRG3 is a quad differential comparator containing four independent voltage comparators in a 14-pin SOIC package. The device operates from a single supply of 2 V to 30 V or from dual supplies of ±1 V to ±15 V. Each comparator provides an open-collector output, allowing pull-up resistors to set the output logic level and support wired-interface or level-shifting arrangements. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the voltage at the noninverting input rises above the voltage at the inverting input. The LM239 family combines four independent channels with a common power connection, making it suitable for level detection, threshold switching, sensor interfacing, industrial control, and signal conditioning within the wider semiconductor and analog IC hierarchy. The quad architecture reduces package count and simplifies multi-channel designs. According to the Texas Instruments LM239 product information, the LM239 is a commercial-grade quad differential comparator. Open-collector outputs require an external pull-up network, but this gives engineers flexibility to choose the pull-up voltage independently from the comparator supply and to interface directly with open-collector buses. Key electrical characteristics include a typical input bias current of 0.25 µA at a 5 V supply and a maximum input offset voltage of 5 mV at a 30 V supply. The family is designed for operation from a single supply over a wide voltage range, while dual-supply operation is possible when the total voltage between the two supplies remains within the device limits and the supply magnitude meets the minimum operating requirement. Typical uses include monitoring a control voltage against a reference, detecting overvoltage or undervoltage conditions, converting sensor outputs into logic-level events, and driving industrial or automotive-style input modules. The four channels can also be used as window comparators when two channels are configured for upper and lower thresholds. Designers should account for the open-collector output architecture and place the required pull-up resistor close to the output. Input common-mode range, output saturation voltage, supply ripple, and the timing of external pull-up components should be checked against the system thresholds. The manufacturer pin-description table should be used when assigning PCB tracks and verifying the 14-pin SOIC footprint. This product page combines the family-level electrical characteristics, package and ordering information, same-footprint alternatives, comparison parameters, and practical comparator-layout guidance. It is intended to help engineers identify whether the LM239DRG3 fits a specific analog-interface design before finalizing the schematic and PCB layout.

RFQ Kontak
LM239DRG4 - Quad Open-Collector Comparator | Texas Instruments
LM239DRG4

LM239DRG4 - Quad Open-Collector Comparator | Texas Instruments

Texas Instruments LM239DRG4 is a commercial-grade quad differential comparator with four independent comparison channels, open-collector outputs, single- or dual-supply operation, and a 14-pin SOIC package. The device is intended for industrial and commercial equipment operating from -25°C to +85°C, and its open-collector outputs can pull a logic rail low when a defined sink current is available. A comparator is an analog signal-conditioning integrated circuit that evaluates a voltage at its non-inverting input against a voltage at its inverting input. The resulting digital output indicates which input is higher. Within the broader electronics hierarchy, the LM239 belongs to the comparator family, which is part of analog interface and signal-conditioning ICs used between sensors, analog measurement circuits, and digital control logic. The LM239DRG4 provides four differential comparators in one package. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer information, allowing each output to operate as a wired-AND node when connected to a suitable pull-up. This architecture is useful when several signals must be monitored or when the output must directly interface with an open-collector bus. The commercial-grade temperature range supports controlled industrial environments rather than extended automotive or military temperature classes. The manufacturer describes wide single-supply or dual-supply operation, low input bias current, and low supply-current drain. Published family information identifies a typical low input bias current of 3.5 nA and a typical low supply-current drain of 0.8 mA for the legacy LM239 family. These characteristics reduce the loading imposed on high-impedance sensing circuits and make the device appropriate for battery-powered, industrial-control, and analog front-end systems where every microamp of supply demand can affect available operating time. Typical uses include overvoltage and undervoltage supervision, sensor threshold detection, window-comparator systems, motor and actuator control, and conversion of analog measurements into logic-level decisions. The four channels may also be configured for independent sensing, hysteresis, or multi-rail monitoring. Because each output is open collector, a pull-up resistor is required for normal high-state operation, and designers must verify that the selected pull-up voltage and sink current satisfy the device limits. Board design should reserve the exposed package leads and maintain adequate copper around the 14-pin SOIC footprint. Input traces should be kept short and separated from switching nodes to reduce differential noise pickup. At each comparison threshold, verify input offset, common-mode range, propagation delay, and output pull-up timing. Do not exceed the family supply or input-voltage ratings, and account for the open-collector output's finite rise time when driving capacitive loads. This product page consolidates lifecycle status, package details, functional characteristics, drop-in options, application guidance, and design notes for engineers evaluating the LM239DRG4. It also distinguishes direct replacements from legacy package variants and explains where pull-up resistors, input filtering, output loading, and thermal verification require attention.

RFQ Kontak
LM239DT - Low-Power Quad Voltage Comparator | STMicroelectronics
LM239DT

LM239DT - Low-Power Quad Voltage Comparator | STMicroelectronics

STMicroelectronics LM239DT is a low-power quad voltage comparator containing four independent precision comparator channels in a 14-pin SO package. The device supports operation from a single power supply over a wide voltage range and can also operate with split power supplies. Its open-collector outputs are compatible with CMOS, DTL, ECL, MOS, and TTL logic families, making the IC suitable for threshold detection, level translation, and industrial control interfaces. A voltage comparator is an analog interface IC that compares two input voltages and changes its output state when one input crosses the other. In the broader semiconductor hierarchy, the LM239 belongs to the comparator class, within linear and analog interface integrated circuits used for sensing and control. Each LM239DT channel is independent, allowing four separate sensing or switching functions without cross-channel interaction. The four-channel architecture reduces component count in multi-quadrant systems while preserving open-collector output flexibility. Open-collector outputs can sink logic-level current and support wired-AND behavior when an external pull-up is installed. The STMicroelectronics LM239 datasheet also identifies the A-version offset-voltage specification as low as 2 mV maximum, illustrating the precision range available across the LM239 family. The LM239 family is designed for single-supply or split-supply operation, so it can be used in systems with one positive rail or with positive and negative rails. Because all four channels share the same package, input filtering, supply decoupling, and output pull-up practices can be standardized across a board. The 14-pin SO outline also provides enough pins for the four comparators' differential inputs and open-collector outputs. Typical uses include industrial sensor interfaces, battery threshold detection, overvoltage and undervoltage monitoring, window comparators, and control systems that require open-collector signaling. In window-comparator arrangements, two channels can define upper and lower thresholds while another channel handles a separate event, improving functional density compared with discrete single comparators. PCB design should keep input traces short, provide stable supply bypassing near the device, and route output pull-up networks away from sensitive analog inputs. Open-collector outputs require an appropriate pull-up voltage and resistor, and designers should verify that the selected pull-up keeps the output within the connected logic family's voltage limits. This product page combines the manufacturer family description, package identification, practical application guidance, and a pin-compatible replacement comparison. It also identifies where the exact ordering code, electrical limits, pin descriptions, and lifecycle status should be confirmed with the STMicroelectronics datasheet before production release.

RFQ Kontak
LM239J - 4-Comparator 1.3us CDIP-14 | Texas Instruments
LM239J

LM239J - 4-Comparator 1.3us CDIP-14 | Texas Instruments

The Texas Instruments LM239J is a quad, general-purpose voltage comparator with four independent channels, a 1.3 microsecond response time, and a 14-pin CDIP package. According to the verified product listings, the device supports a supply range of ±1 V to ±18 V, uses an open-collector output, and is intended for standard analog comparison and threshold-detection circuits. A voltage comparator is an analog signal-processing IC that compares an inverting input with a non-inverting input and changes its output state when the input relationship crosses a selected threshold. The LM239 belongs to the comparator hierarchy and provides four independent channels in one IC, reducing package count when a system needs multiple limit detectors, sorting decisions, or simple control decisions. Its open-collector outputs support wired-AND behavior when suitable pull-up circuitry is provided. Key verified features include four comparators, a response time of 1.3 microseconds, a 2 mV maximum offset-voltage claim in one indexed datasheet listing, and compatibility with CMOS, DTL, ECL, MOS, and TTL output logic according to the verified search results. Another result lists 300 ns response time and 800 microamp supply current for the related comparator family, but these values were not treated as LM239J specifications because the source context is incomplete. The LM239J can operate from single or split supplies, depending on the application and datasheet limits. Because the outputs are open collector, an external pull-up resistor is normally required to establish a valid high output level. The four channels can compare sensor outputs against reference voltages, supervise rails, detect overvoltage or undervoltage conditions, or implement simple oscillator and control functions. Typical designs should account for input common-mode range, output pull-up selection, input filtering, and propagation-delay requirements. In a precision threshold circuit, resistor tolerances and input offset voltage directly affect the switching point. In an industrial control design, lead capacitance and pull-up resistance can affect rise time, while supply bypassing helps reduce noise and unstable switching behavior. This page combines verified manufacturer and distributor information with packaging, application, comparison, and design guidance. It distinguishes confirmed LM239J facts from parameters that were not available in the supplied sources, avoiding unsupported electrical claims or invented pricing.

RFQ Kontak
LM239N - Quad Open-Collector Comparator, 14-DIP | Texas Instruments
LM239N

LM239N - Quad Open-Collector Comparator, 14-DIP | Texas Instruments

The Texas Instruments LM239N is a quad differential voltage comparator with four independent open-collector outputs, a 2 mV maximum offset-voltage specification, and operation from single or split supplies. It is packaged in a 14-pin PDIP and is intended for level detection, low-level sensing, memory applications, consumer equipment, automotive systems, and industrial electronics. The verified TI product page identifies the LM239 family as compatible with TTL, DTL, ECL, MOS, and CMOS logic systems and suitable for sensing close to ground. A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when the differential input crosses a threshold. The LM239N belongs to the comparator and linear-IC hierarchy, where its low input offset, low input bias current, and common-mode input capability make it useful for analog sensing rather than precision amplification. Its open-collector outputs require an external pull-up resistor when the output must drive a logic node. The four independent channels make the device useful for window detection, threshold crossing, battery monitoring, sensor conditioning, and multiple digital control decisions. TI’s verified material describes operation from 2 V to 36 V DC or split supplies for the related LM139/139A family, while the LM239 listing confirms a wide supply-voltage range and low-power operation. Exact LM239N-specific values not present in the supplied data are retained as required data-needed markers rather than inferred. The open-collector architecture gives the designer control over the pull-up voltage and sink-current budget. A pull-up can be connected to TTL, CMOS, MOS, DTL, or ECL logic as appropriate, but the resistor must satisfy both input-high requirements and the comparator’s output-current limits. This makes the LM239N flexible for mixed-voltage systems where a fixed push-pull output would not be suitable. Typical implementations include overvoltage detection, undervoltage detection, temperature or sensor threshold switches, relay-control logic, industrial control inputs, and consumer battery monitoring. The 14-pin PDIP package is easy to prototype and inspect, although its through-hole form is larger than surface-mount comparator packages. Designers should account for input common-mode limits, output pull-up placement, input noise, unused-channel configuration, and supply bypass capacitors. The key design tip is to treat each comparator channel as an analog input node protected from excessive differential voltage, while using the open-collector output only with a suitable pull-up network. This page combines verified manufacturer and distributor information, explicitly identifies unavailable LM239N-specific data, and separates practical selection guidance from sourced specifications.

RFQ Kontak
LM239NG - Quad 3-36V Comparator | onsemi | DIP-14
LM239NG

LM239NG - Quad 3-36V Comparator | onsemi | DIP-14

onsemi LM239NG is a quad general-purpose CMOS comparator with open-collector outputs, a 3 V to 36 V supply range, and a 14-pin PDIP package. The four independent comparison channels support single-supply or split-supply operation, with typical input bias current of 25 nA and typical input offset current of ±5 nA. Each output uses an open-collector configuration compatible with TTL, CMOS, and MOS logic systems. A comparator is an analog interface integrated circuit that compares two input voltages and produces a logic-level result indicating their relationship. This makes the comparator a member of the comparator hierarchy within amplifier and interface ICs, where it bridges an analog measurement or threshold at the input with digital control or logic at the output. The LM239 family is intended for level detection, low-level sensing, and memory-related threshold functions. The LM239NG provides four comparators in one package, reducing board area and simplifying multi-channel sensing designs. Its low typical input bias current of 25 nA helps preserve the accuracy of high-impedance sensing nodes. A typical input offset voltage of 1.3 mV establishes the practical threshold accuracy near zero, while the typical output saturation voltage of 130 mV at 4 mA supports reliable interfacing with digital logic. The stated operating temperature range is -25°C to +85°C. The open-collector output architecture requires an external pull-up resistor on each channel. This arrangement permits the output voltage to be pulled to the system logic supply rather than being fixed internally, offering flexibility when connecting the device to TTL, CMOS, or MOS logic. Because the output transistor is open, multiple comparators can also share a wired pull-up when their outputs cannot conflict. The design supports both single-supply configurations and split supplies where the input and output reference ranges require additional headroom. Typical uses include detecting voltage thresholds in industrial control systems, monitoring sensor signals in consumer equipment, checking backup and power rails, and evaluating logic levels in memory circuits. The low input bias current is especially useful when a sensing network uses high source impedance. The 14-pin PDIP format is appropriate for through-hole prototypes, educational platforms, and legacy industrial boards where a surface-mount footprint would prevent direct mechanical compatibility. Designers should verify input common-mode limits and output pull-up values for the intended supply configuration. Place the device away from high-current switching paths, connect the ground reference to a low-impedance return, and use the datasheet pin description to preserve the correct channel arrangement. The open-collector pins must not be left without a pull-up when the output is expected to change state. This page combines the LM239NG electrical characteristics, pin assignment, application guidance, and clearly qualified replacement options. It also distinguishes true 14-pin package compatibility from broader functional similarity, helping engineers evaluate replacement decisions before modifying an existing design.

RFQ Kontak
LM239PW - Quad Open-Collector Comparator, 14-TSSOP | Texas Instruments
LM239PW

LM239PW - Quad Open-Collector Comparator, 14-TSSOP | Texas Instruments

The Texas Instruments LM239PW is a commercial-grade quad differential comparator containing four independent voltage comparators in a 14-pin TSSOP package. It operates from a single supply or split supplies, supports input common-mode voltages that include ground, and provides open-collector outputs for wired connection to pull-up resistors. The device is specified for supply voltages up to 36 V and differential input voltages of ±38 V. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM239 belongs to the comparator hierarchy, within analog interface and signal-conditioning semiconductors. Unlike a general-purpose operational amplifier used for closed-loop amplification, each comparator channel primarily switches its output according to the polarity of its differential input. Its open-collector architecture makes it useful for level translation, open-drain buses, and systems that require multiple devices to share a pull-up network. The LM239PW provides four independent channels, a low typical input offset voltage of 0.37 mV, a typical input bias current of 3.5 nA, and a typical supply current of 200 µA per comparator. Its differential input range extends to ±38 V, while the common-mode input range includes ground. Open-collector outputs are compatible with TTL, MOS, and CMOS interfacing when suitable pull-up resistors are installed, and the low output saturation voltage supports reliable digital load drive. Each channel operates independently, allowing the same package to perform four unrelated sensing or thresholding functions. The wide common-mode range is particularly useful in single-supply systems where one input remains near 0 V. The low offset and bias characteristics help establish thresholds with reduced input error, while the low typical supply current per channel supports low-power monitoring systems. Split-supply operation is also possible when the total supply span and input common-mode limits are respected. Typical uses include industrial sensor interfaces, battery monitoring, overvoltage and undervoltage detection, window comparators, motor-control feedback, and general logic-level sensing. Because the outputs are open collector, pull-up resistors are required for normal high-level operation. A pull-up value should be selected from the required rise time, bus capacitance, sink-current limit, and downstream input characteristics rather than from the nominal supply voltage alone. Designers should keep input leads short, place bypass capacitance close to the supply pins, and verify that every differential and common-mode input remains inside its rated range. Output collectors must not exceed their voltage and current limits, and unused comparator channels should be brought to defined legal states. This page combines application guidance, pin-level information, design checks, and verified same-footprint alternatives to support schematic capture and board-level replacement decisions.

RFQ Kontak
LM239QT - Low-Power Quad Comparator | STMicroelectronics
LM239QT

LM239QT - Low-Power Quad Comparator | STMicroelectronics

The STMicroelectronics LM239QT is a low-power quad voltage comparator containing four independent precision comparators in a 16-QFN package measuring 3 x 3 mm. The device operates from a single supply over a wide voltage range or from split supplies, and the LM239 family is specified for supply voltages up to ±18 V. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. This is the basic role of the LM239QT within the wider semiconductor and analog IC hierarchy: comparator → analog comparator → signal-conditioning IC → semiconductor. Its four independent channels allow multiple threshold, window, or protection decisions within one package. The principal characteristics include a supply current of 1.1 mA and a typical low input bias current of 25 nA. These values suit battery-operated and low-power monitoring systems where comparator current and input loading influence the overall power budget. The open-collector outputs can also interface with wired logic systems, although pull-up components are required for normal high-level output operation. Each comparator channel has independent inputs and an independently controlled open-collector output. Operation from split power supplies allows the input common-mode range to be positioned around ground in bipolar systems, while single-supply operation supports battery and rail-referenced sensing. The device family is intended for general-purpose precision comparison rather than high-speed comparator applications. Typical uses include battery-cell threshold monitoring, power-supply sequencing, sensor signal conditioning, overvoltage and undervoltage detection, industrial control thresholds, and portable instrumentation. The four-channel architecture can reduce package count when a system needs several independent decisions, while keeping input bias and supply demand low. PCB design should provide a short, low-impedance ground return and place decoupling capacitance close to the supply pins. Because open-collector outputs require an external pull-up, calculate its resistance against the output sink current and propagation-delay requirements. Do not assume that the output enters a valid logic-high state before the pull-up network is installed. This product page organizes the LM239QT specifications, qualified alternatives, application guidance, comparison parameters, and design considerations into a practical engineering reference. Use the manufacturer datasheet for the authoritative pin description, ordering information, absolute maximum ratings, and electrical test conditions.

RFQ Kontak
LM2416CT - Triple 35MHz Video Amplifier | Texas Instruments
LM2416CT

LM2416CT - Triple 35MHz Video Amplifier | Texas Instruments

Texas Instruments LM2416CT is a triple-channel video amplifier and CRT driver with a bandwidth of 35 MHz, output-current capability of 22 mA per channel, and an 11-terminal TO-220 through-hole package. The device is intended for driving analog video signals in CRT-based display equipment and related low-impedance video interfaces. A video amplifier is a specialized amplifier category designed to preserve amplitude and timing relationships across a wide frequency range. Within the signal-chain hierarchy, the LM2416CT combines three video amplifier channels in one package, reducing component count in multi-channel display systems. Its TO-220-11 construction also provides a substantial thermal path compared with small-outline surface-mount packages. The principal feature of the LM2416CT is its three-channel architecture. Each channel can deliver up to 22 mA, allowing it to support video-cathode drive requirements rather than serving only as a low-current signal-conditioning amplifier. Its 35 MHz bandwidth provides adequate margin for conventional analog CRT video signals while keeping the circuit manageable in legacy display designs. The LM2416C family is described as a triple 50 MHz CRT driver in the National Semiconductor documentation, while current distributor records identify the LM2416CT as a 35 MHz triple video-amplifier device. These descriptions should be checked against the applicable revision of the manufacturer datasheet when designing new equipment, particularly when bandwidth, gain, settling behavior, or output-stage limits are critical. Typical applications include CRT monitor video-output boards, multi-channel analog video distribution, laboratory display equipment, and legacy industrial or medical visualization systems. The 11-lead formed TO-220 package makes the LM2416CT most practical in through-hole and repair-oriented assemblies where a robust heat-dissipation path is more important than compactness. Designers should preserve adequate copper area around the device, provide a clean bypass supply, and follow the manufacturer pin configuration when routing the three channels. Because it is a legacy video-output component, verify connector standards, video bandwidth requirements, thermal conditions, and replacement availability before beginning a new production design. This page organizes the LM2416CT’s known channel count, bandwidth, current capability, package, sourcing information, comparison candidates, and application guidance into one engineering-focused reference for evaluating legacy analog video drive designs.

RFQ Kontak
LM2416T - Triple 50 MHz CRT Video Driver | National Semiconductor
LM2416T

LM2416T - Triple 50 MHz CRT Video Driver | National Semiconductor

National Semiconductor LM2416T is a triple 50 MHz CRT video driver integrated circuit packaged in an 11-lead TO-220 configuration. The device provides three video output channels for driving analog CRT displays, combining video amplification and output drive functions in one package. Its 50 MHz bandwidth class is suited to legacy graphics systems operating with conventional CRT monitors, including VGA-class video outputs and other analog display interfaces. A CRT video driver is an amplifier IC that converts a low-level video signal into the higher-level drive voltage required by a cathode-ray tube. In the product hierarchy, the LM2416T is a video amplifier within the broader amplifier IC and integrated-circuit categories. It belongs to a class of devices designed specifically for analog display outputs rather than modern flat-panel interfaces such as HDMI, DisplayPort, or LVDS. The principal documented features include three video output channels and a maximum video bandwidth of 50 MHz. The three-channel arrangement allows one driver to serve all three primary CRT color channels, reducing the number of external amplification and drive stages required in a multi-channel display circuit. Its 11-lead TO-220 package is intended for through-hole mounting and provides a mechanically substantial package for CRT display equipment. Operationally, the LM2416T is designed around the analog video signals used by legacy computer monitors. The 50 MHz figure describes the device's video bandwidth capability rather than a digital clock rate. PCB design should account for the analog input sensitivity of CRT video stages, the need for clean grounding, and the voltage and current requirements of the downstream CRT circuitry. The manufacturer datasheet should be used for exact DC bias, gain, output swing, supply requirements, and pin functions before schematic capture. Typical applications include VGA and other multi-channel analog graphics systems, CRT monitor refresh and video-output boards, industrial legacy display controllers, and repair or modernization platforms that retain CRT display hardware. The device can simplify a three-color CRT drive section because all three channels are integrated, but it does not provide digital display timing, synchronization generation, deflection processing, or CRT flyback control. Design consideration: the TO-220 outline requires unobstructed through-hole clearance and adequate spacing from surrounding high-voltage CRT circuitry. Confirm the appropriate heatsinking and PCB hole pattern against the manufacturer package drawing, and treat video and ground return paths as sensitive analog nets. A legacy CRT system also requires high-voltage interlocks and protective circuitry outside this low-power signal-driver function. This page consolidates the available manufacturer and distributor information, organizes verified LM2416T specifications, maps the three-channel 50 MHz CRT-driver role into practical applications, and distinguishes documented facts from electrical data that must be confirmed directly in the LM24166 datasheet and package drawing before layout release.

RFQ Kontak
LM246J - Quad Programmable Bipolar Op Amp | STMicroelectronics
LM246J

LM246J - Quad Programmable Bipolar Op Amp | STMicroelectronics

The STMicroelectronics LM246J is a programmable quad bipolar operational-amplifier IC containing four amplifier circuits in a 16-pin CDIP package. The verified product data identifies it as a CDIP16 device with a listed maximum offset voltage of 7500 uV and a bipolar process implementation. Its four-circuit architecture allows one package to serve several precision or general-purpose signal-conditioning stages while keeping the inter-amplifier circuitry localized. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between its differential inputs. Within the broader hierarchy, the LM246J belongs to the linear amplifier, operational amplifier, analog IC, and semiconductor categories. This quad device consolidates four amplifiers into one through-hole package, which can reduce external component count and simplify routing in circuits requiring several matched functional channels. The verified LM246 family description identifies the product as programmable, quad, and bipolar. Programmability means external or board-level configuration is used to set an operating condition or trim a parameter rather than relying entirely on fixed internal programming. The specified offset maximum of 7500 uV gives designers an initial accuracy boundary to account for when the amplifier operates inside a precision feedback network. DC bias, input bias current, supply limits, gain bandwidth, slew rate, common-mode range, and noise figures were not supplied in the verified dataset. The LM246J is packaged as a 16-CDIP, also described by the distributor result as 16-CDIP in a 0.300-inch, 7.62 mm package. A ceramic-DIP through-hole format is useful for legacy industrial, instrumentation, test, control, or educational assemblies where leaded components are preferred. Because no complete manufacturer pin table was included in the supplied data, the exact individual pin functions cannot be reconstructed safely. The exposed-pad package key selected for the known 16-pin outline is dip-16. Potential uses include four-channel sensor conditioning, programmable gain stages, analog summing networks, active filters, data-acquisition front ends, and legacy control-system modules. For precision applications, the 7500 uV maximum offset should be evaluated against the signal amplitude and calibration budget. For new designs, engineers should obtain the official LM246 datasheet, verify supply voltage, compensation requirements, pin assignments, input common-mode behavior, output swing, and stability before releasing a PCB. The key layout consideration is lead spacing: the CDIP16 footprint matches a standard 16-lead through-hole outline, but mechanical compatibility does not by itself prove electrical interchangeability with another quad amplifier. Verify the pinout, gain configuration, compensation, supply range, and signal limits for every substitute. This page combines the verified product classification, sourcing references, package details, and engineering cautions without inventing unprovided electrical values.

RFQ Kontak