A3P060-1FG144 - 60K Gate ProASIC3 FPGA | Microchip
MPN: A3P060-1FG144 ✓ NakahandaA3P060-1FG144 Ulas
A ProASIC3 FPGA is a nonvolatile semiconductor device that stores its programmed configuration in flash memory. This places it in the hierarchy of programmable logic devices, where an FPGA provides configurable gates, registers, memory and I/O blocks that can be updated without removing the device from the circuit. The A3P060 combines this programmable architecture with a low-pin-count 144-LBGA package.
The device provides 60000 system gates, 1536 logic cells and 96 user I/Os. The -1 suffix identifies speed grade 1, while FG144 identifies the 144-ball package. Its flash-based configuration supports instant-on and reprogrammable operation, making it suitable for control logic, interface bridging, instrumentation and embedded system functions that benefit from field updates. The product family is also documented for automotive-oriented ProASIC3 variants, but the temperature qualification of this exact ordering code must be confirmed against its ordering information.
Compared with a fixed ASIC, the A3P060 allows logic changes without a silicon mask change and supports the same broad design flow used for FPGA development. Its 60000-gate resource level is suited to moderate-complexity parallel logic rather than processor-heavy systems. The 96-I/O count provides substantial connectivity in a compact package, although board planning must account for the fine-pitch 144-LBGA land pattern and careful escape routing.
Typical uses include industrial control modules, data-acquisition front ends, communications adapters, embedded test equipment and compact instrumentation. Designers can map counters, state machines, bus interfaces, protocol converters and control functions into the same device, reducing the number of discrete logic components. A key engineering benefit is nonvolatile configuration: the programmed design remains available after power cycling without an external configuration loader.
PCB implementation should prioritize BGA assembly capability, via-in-pad and blind-buried-via rules, clean power distribution and decoupling close to the device. Signal-integrity checks are necessary on user I/O paths, while timing closure should use the speed-grade-1 timing constraints for the selected clock and I/O standards. Because the exact pin map is extensive, use the manufacturer pin-description table when assigning board nets.
This page combines the verified A3P060 family specifications with package-aware alternatives, comparison parameters and practical FPGA layout guidance, helping engineers evaluate whether the A3P060-1FG144 matches the required logic density, package, speed grade and application environment.
Mga alternatibo na pwedeng ilagay na A3P060-1FG144 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok A3P060-1FG144 (parehas na form factor at footprint) — pagkakaiba sa Package, Device Type, Configuration Memory, Process Technology, User I/O Count.
A3P060-1FG144I
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
A3P060-1FG144T
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →A3P060-FG144
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →A3P060-FG144I
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →A3P060-1FG144II
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
A3P060-1FG144 Mga Pinakamataas na Rating at Electrical Characteristics
| Device Type | ProASIC3 flash FPGA |
| System Gates | 60000 gates |
| Logic Cells | 1536 logic cells |
| User I/O Count | 96 I/Os |
| Device Pin Count | 144 pins |
| Packhaging | 144-LBGA, 13 x 13 mm |
| Package Pitch | 1.0 mm pitch |
| Package Height | 1.45 mm |
| Speed Grade | Grade 1 |
| Temperature Grade | Commercial |
| Configuration Memory | Flash |
| Process Technology | 130 nm |
| Metal Layers | 7 layers, 6 copper layers |
| Internal Frequency | 350 MHz |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng A3P060-1FG144 1.45 mm
Pin configuration para sa A3P060-1FG144 (1.45 mm package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa A3P060-1FG144.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
A3P060-1FG144 ay nararapat para sa 6 aplikasyons: Industrial Control Logic, Data-Acquisition Front End, Communications Adapter, Embedded Test Equipment, Programmable Instrumentation, Secure Embedded System Control.
Industrial Control Logic
The A3P060-1FG144 is suitable for compact industrial controllers that combine state machines, counters, interlocks and actuator logic in one programmable device. Its 60000 system gates and 1536 logic cells provide substantial parallel-logic capacity, while 96 user I/Os reduce the number of separate logic packages around a control board. Flash-based configuration preserves the programmed control sequence during power cycles and permits field updates when operating conditions or firmware behavior change. The -1 speed grade supports deterministic timing decisions, but every path must still be closed against the selected clock and I/O standards. The 144-LBGA footprint is compact, yet it requires an assembly process qualified for 1.0 mm-pitch BGA components.
Inirekomenda
Data-Acquisition Front End
The A3P060-1FG144 can implement channel control, trigger sequencing, digital filtering and data-format conversion ahead of an analog-to-digital converter. Its 96 user I/Os allow multiple converters, sensors, capture indicators and memory devices to share a tightly coordinated timing domain. With 1536 logic cells and 60000 system gates, the device has adequate capacity for parallel pipelines and multi-channel state management without moving to a larger FPGA. Flash configuration also simplifies field-instrument updates because the acquisition configuration remains resident in nonvolatile memory. Signal-integrity planning remains essential, particularly for high-speed converter interfaces, clock distribution and simultaneous-switching output effects around the fine-pitch 144-LBGA device.
Inirekomenda
Communications Adapter
A3P060-1FG144 applications include protocol converters, interface bridges and communications adapters that translate between embedded serial or parallel interfaces. The programmable logic blocks can implement buffering, framing, timeout, error detection and FIFO-like data movement, while 96 user I/Os provide enough board-level connectivity for several independent channels. Its nonvolatile flash configuration permits field reprogramming without external configuration memory, which is valuable in distributed equipment where physical access is inconvenient. Timing constraints should be applied to each interface independently because the 350 MHz internal frequency is a device capability rather than a guaranteed user-I/O rate. Board layout should isolate sensitive clock paths and route high-speed nets over continuous reference planes.
Inirekomenda
Embedded Test Equipment
The A3P060-1FG144 can consolidate programmable test sequences, pattern generation, timing control and result-capture logic in compact instrumentation. Its 1536 logic cells are well suited to parallel state machines and digital pattern logic, while the 96-I/O budget allows connection to DUTs, fixture controls and status indicators. A single-chip implementation can reduce discrete logic count and simplify programmable test sequences, particularly when the same board must cover several test modes. Flash configuration supports controlled fixture updates and repeatable setup after power cycling. Designers should reserve clean clock distribution, implement series damping where required and validate the BGA assembly using an appropriate solder-joint inspection method.
Inirekomenda
Programmable Instrumentation
The A3P060-1FG144 is a strong fit for programmable signal-conditioning and measurement instruments where multiple internal modes share common hardware. Its 60000 gates can accommodate digital filters, trigger managers, calibration tables, counters and interface control, while flash configuration permits the instrument to retain a selected measurement configuration between power cycles. The 144-LBGA package helps limit board area when the device must coexist with precision analog circuitry. For low-noise analog sections, maintain separation from digital return currents and place decoupling at the relevant power balls. The commercial A3P060-1FG144 ordering code should be checked against the instrument’s ambient-temperature range before deployment in industrial environments.
Inirekomenda
Secure Embedded System Control
A3P060-1FG144-based designs can combine flash-resident configuration, programmable state logic and I/O control in compact embedded equipment. The nonvolatile configuration supports instant-on behavior after power restoration, while the programmable architecture allows protocol and control updates without changing the PCB. Its 1536 logic cells are appropriate for supervisory logic, health monitoring, secure command parsing and deterministic actuator sequencing. A multi-rail implementation should assign supply sequencing and keep sensitive interfaces away from noisy switching nodes. Because the exact security certification and temperature status of this ordering code are not established, security-critical and automotive programs must verify qualification, cryptographic requirements and environmental limits through Microchip’s official documentation.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for A3P060-1FG144 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | A3P060-1FG144I | A3P060-1FG144T | A3P060-FG144 | A3P060-FG144I | A3P060-1FG144II |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | FG144 144-LBGA, 13 x 13 mm | FG144 144-LBGA, 13 x 13 mm | FG144 144-LBGA, 13 x 13 mm | FG144 144-LBGA, 13 x 13 mm | FG144 144-LBGA, 13 x 13 mm | FG144 144-LBGA, 13 x 13 mm |
| Device Architecture | ProASIC3 flash FPGA | ProASIC3 flash FPGA | ProASIC3 flash FPGA | ProASIC3 flash FPGA | ProASIC3 flash FPGA | ProASIC3 flash FPGA |
| System Gates | 60000 gates | 60000 gates | 60000 gates | 60000 gates | 60000 gates | 60000 gates |
| Logic Cells | 1536 logic cells | 1536 logic cells | 1536 logic cells | 1536 logic cells | 1536 logic cells | 1536 logic cells |
| User I/O | 96 I/Os | 96 I/Os | 96 I/Os | 96 I/Os | 96 I/Os | 96 I/Os |
| Configuration Memory | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash |
| Internal Frequency | 350 MHz | 350 MHz | 350 MHz | 350 MHz | 350 MHz | 350 MHz |
Pangunahing mga Pagkakaiba
- Commercial speed-grade-1 configuration in the compact FG144 package (kumpara saA3P060-FG144)
- Broader environmental qualification options in the same 144-LBGA footprint (kumpara saA3P060-1FG144I)
- Compact 60000-gate implementation with 96 user I/Os (kumpara saA3P060-1TQ144)
Talaan ng Disenyo
Treat the FG144 land pattern as a fine-pitch BGA problem rather than a conventional leaded-component layout. Follow the manufacturer escape-routing and via rules for the selected board stack-up, maintain the specified pad and via dimensions, and verify that the assembly supplier supports 1.0 mm-pitch BGA placement. Place programming, configuration and test access points where they remain reachable after board assembly, and avoid placing tall components that can obstruct inspection or rework operations.
Use the manufacturer power-definition table to identify every supply, ground and auxiliary ball before dividing the 144-LBGA footprint into power and signal groups. Decoupling capacitors should be placed directly across the relevant device-side power and ground connections, with additional bulk capacitance placed near the supply entry point. Separate sensitive analog reference returns from digital switching returns where the board architecture permits, and validate voltage sequencing and transient response under the highest expected I/O activity.
Create timing constraints for every clock domain and use the speed-grade-1 timing tables when closing the design. Route clocks on continuous reference planes, avoid unnecessary layer changes, and add source-series termination where output-edge requirements demand it. The 350 MHz internal frequency is not a guaranteed external-interface rate; user-I/O standards, package-ball transitions, loading and board topology determine achievable throughput. Run post-route timing analysis after final BGA escape and fanout routing.
Estimate worst-case junction temperature using the actual utilization of the 60000-gate device, switching activity, I/O load, ambient temperature and the manufacturer thermal model for the selected package and board stack-up. Dense logic or high I/O activity can create local hot spots even when average FPGA utilization appears moderate. Preserve uninterrupted copper beneath and around the BGA where the land pattern permits, and use thermal analysis rather than average activity alone when defining the final power budget.
Impormasyon ng Pagsunod sa Kautusan
Exact compliance declarations were not identified for A3P060-1FG144. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals and automotive qualification status against the current Microchip documentation for the selected ordering code.