ADF4007BCP - 7.5GHz Divider/PLL Synthesizer | Analog Devices
MPN: ADF4007BCP ✓ NakahandaADF4007BCP Ulas
A phase-locked loop, or PLL, is a feedback-controlled frequency-synthesis circuit in which a phase-frequency detector compares a reference signal with a divided feedback signal. A charge pump and external loop filter then convert phase error into a tuning voltage for a voltage-controlled oscillator. The ADF4007BCP integrates the phase detector, precision charge pump, programmable divider, and prescaler used to construct such a loop.
The ADF4007BCP supports RF operation to 7.5 GHz and phase-frequency-detector operation to 120 MHz. Its reference divider is permanently set to 2, permitting an external REFIN frequency up to 240 MHz. Divide ratios are selected through two external control pins, while RSET controls charge-pump current. A separate VP supply allows the tuning-voltage range to exceed what the main 3.3 V supply alone would permit.
The device also includes hardware power-down control for system-state management. According to the Analog Devices ADF4007 data sheet, the loop-filter values derived with ADIsimPLL provide typical phase noise of -100 dBc/Hz at a 10 kHz carrier offset, while the loop filter attenuates spurs below -90 dBc. These figures make the synthesizer suitable for RF communication systems requiring predictable phase noise and spur performance.
Typical uses include wireless transceiver frequency synthesis, microwave and RF test equipment, and communications infrastructure. In a PLL implementation, the ADF4007BCP compares the divided feedback output with REFIN and drives a VCO tuning input through an external charge-pump loop filter. Designers must select divider ratios, loop bandwidth, and passive values that satisfy the required phase-noise and spur limits.
A key implementation consideration is the exposed thermal pad. The data sheet controls its connection to ground and provides thermal and electrical layout guidance. Input, reference, charge-pump, and loop-filter connections should follow the manufacturer’s recommended layout to avoid introducing additional phase noise or instability.
This page consolidates the verified manufacturer information, available ordering data, same-package cross-references, comparison points, and practical design guidance for engineers evaluating the ADF4007BCP.
Mga alternatibo na pwedeng ilagay na ADF4007BCP — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
ADF4007BCPZ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADF4007BCPZ-RL7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADF4007BCP Mga Spesipikasyon
| Product Type | High-frequency divider/PLL synthesizer |
| Maximum RF Operating Frequency | 7.5 GHz |
| Maximum PFD Frequency | 120 MHz |
| Maximum External REFIN Frequency | 240 MHz |
| Reference Divider Ratio | 2:1 fixed |
| Power Supply | 3.3 V |
| Supported System Voltage | 3 V |
| Charge-Pump Supply | Separate VP supply for extended tuning voltage |
| Typical Phase Noise | -100 dBc/Hz at 10 kHz offset |
| Typical Spur Level | Below -90 dBc |
| Charge-Pump Current Control | RSET controlled |
| Divider Ratio Control | Two external control pins |
| Power-Down Feature | Hardware power-down mode |
| Packhaging | 20-lead LFCSP with exposed pad |
| Bilang ng Pin | 20 pins |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng ADF4007BCP 20-lead lfcsp with exposed pad
Pin configuration para sa ADF4007BCP (20-lead lfcsp with exposed pad package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ADF4007BCP.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ADF4007BCP ay nararapat para sa 6 aplikasyons: Wireless Transceiver Frequency Synthesis, Microwave RF Signal Generation, Communications Infrastructure RF Synthesis, RF and Microwave Test Equipment, High-Frequency Local Oscillator, Frequency-Changing RF Up/Down Converters.
Wireless Transceiver Frequency Synthesis
The ADF4007BCP fits wireless transceiver local-oscillator synthesis because it supports RF frequencies up to 7.5 GHz and PFD operation up to 120 MHz. It can divide a divided feedback signal, compare it with REFIN, and use its precision charge pump to drive an external VCO tuning input. A separate VP supply expands the available tuning-voltage range, while RSET permits charge-pump-current adjustment for loop dynamics. The implementation trade-off is that engineers must design and validate an external loop filter against phase-noise and spur targets.
Inirekomenda
Microwave RF Signal Generation
The ADF4007BCP is applicable to microwave signal-generation systems requiring a high-frequency divider and PLL core rather than a fully integrated oscillator. Its 7.5 GHz RF operating limit gives the feedback divider substantial headroom for microwave carrier generation. The phase detector can operate to 120 MHz, and the permanently fixed divide-by-2 reference path accepts REFIN up to 240 MHz. Performance depends on the selected divide ratio, external VCO tuning range, and carefully calculated loop-filter component values.
Inirekomenda
Communications Infrastructure RF Synthesis
The ADF4007BCP can serve as the frequency-synthesizing core in communications infrastructure that derives coherent RF references from a stable external oscillator. Its 120 MHz maximum PFD rate permits useful comparison bandwidth for suitable reference plans, while the 7.5 GHz RF rating supports high-frequency channels. The separate VP supply is valuable when a VCO requires a tuning range broader than the 3.3 V main rail. Deployment requires local loop-filter analysis, reference-jitter budgeting, and validation of spur behavior in the completed receiver or transmitter.
Inirekomenda
RF and Microwave Test Equipment
The ADF4007BCP offers a practical way to construct a tunable RF source for test equipment when the system already includes an external VCO. The 7.5 GHz divider capability and 120 MHz PFD limit support carrier generation across high-frequency test ranges. According to the Analog Devices data sheet, a typical ADIsimPLL-derived loop-filter implementation reaches approximately -100 dBc/Hz at a 10 kHz offset and attenuates spurs below -90 dBc. These are typical—not guaranteed maximum—figures and must be confirmed for the selected VCO and loop bandwidth.
Inirekomenda
High-Frequency Local Oscillator
The ADF4007BCP can form the synthesizer section of a high-frequency local oscillator using an external voltage-controlled oscillator and loop filter. Its RF bandwidth extends to 7.5 GHz, while the independent charge-pump supply helps accommodate the oscillator’s tuning-voltage requirements. The reference divider is fixed at 2, so the architecture is particularly relevant when a reference plan intentionally avoids an adjustable reference divider. Designers should still verify phase margin, reference-noise multiplication, and capture behavior across all required divide ratios.
Inirekomenda
Frequency-Changing RF Up/Down Converters
The ADF4007BCP is suitable for the programmable frequency-generation section of RF up-converters and down-converters. The phase detector compares a divided RF output with the reference, and the charge pump generates the tuning correction applied to the local oscillator. Operation to 7.5 GHz accommodates many microwave conversion bands, while the 120 MHz PFD ceiling supports reference architectures with a relatively high comparison rate. Image rejection and conversion performance still depend on the complete synthesizer, filters, mixer architecture, and selected loop bandwidth.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ADF4007BCP — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ADF4007BCPZ | ADF4007BCPZ-RL7 |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-WFQFN Exposed Pad | 20-WFQFN Exposed Pad | 20-WFQFN Exposed Pad |
| Maximum RF Frequency | 7.5 GHz | 7.5 GHz | 7.5 GHz |
Pangunahing mga Pagkakaiba
- Matches the verified ADF4007 family frequency capability (kumpara saADF4007BCPZ)
- Supports a flexible external-VCO tuning range (kumpara saADF4007BCPZ)
- Offers a verified 120 MHz PFD comparison rate (kumpara saADF4007BCPZ-RL7)
Talaan ng Disenyo
Use the Analog Devices recommended land pattern and route the charge-pump and loop-filter connections as short as practical. Keep the external VCO tuning path away from noisy digital and switching nodes, and provide a clean return path for the reference and RF divider connections. Because the verified data does not provide exact layout dimensions, the package drawing and ADF4007 data sheet should be treated as the authoritative layout sources.
Connect and thermally couple the exposed pad according to the manufacturer package guidance. The verified material identifies the ADF4007BCP as a 20-lead LFCSP with an exposed pad but does not provide verified junction-temperature or thermal-resistance figures. Before production release, obtain those values from the data sheet and calculate worst-case dissipation using the actual supply voltage, VCO tuning voltage, and charge-pump duty cycle.
Determine the loop bandwidth from phase-noise, spur, reference-jitter, and lock-time requirements rather than copying one filter value across all divide ratios. The Analog Devices data sheet notes that ADIsimPLL was used to derive the shown component values, with typical phase noise of -100 dBc/Hz at 10 kHz offset and spurs below -90 dBc. Validate these typical figures using the actual VCO, reference source, crystal or oscillator, and system thermal conditions.
Do not treat the 7.5 GHz RF rating as permission to exceed the 120 MHz PFD limit or the 240 MHz external REFIN limit. The reference divider is permanently set to 2, so reference planning cannot compensate with an adjustable reference divider. Also avoid omitting the separate charge-pump supply or RSET path; these functions are central to the advertised tuning-voltage range and charge-pump-current control.
Impormasyon ng Pagsunod sa Kautusan
The supplied verified snippets do not contain explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. No compliance status has been inferred from the ordering suffix.
