ADP2370ACPZ-R7 - 800mA, 15V Buck DC-DC Converter | Analog Devices
MPN: ADP2370ACPZ-R7 ✓ NakahandaADP2370ACPZ-R7 Ulas
A buck (step-down) DC-DC converter is a switching voltage regulator that uses an inductor, a switch, and a rectifier to convert a higher input voltage to a lower output voltage with high efficiency. The buck converter sits within the broader hierarchy of DC-DC converters -> switching regulators -> voltage regulators -> power management ICs -> semiconductors. By cycling the internal MOSFETs at high frequency and filtering with an LC network, a buck converter achieves efficiencies typically above 90 percent, vastly superior to linear regulators at large input-to-output voltage differentials.
Key features of the ADP2370 include up to 800 mA of continuous output current, 92 percent peak efficiency at 1.2 MHz operation, low quiescent current for extended battery life, internal compensation, internal soft start, power-good output, and thermal shutdown. The device integrates high-side and low-side MOSFETs, eliminating the need for external switching transistors. Forced PWM (FPWM) mode maintains a constant switching frequency for noise-sensitive applications, while automatic PWM/PFM mode maximizes efficiency at light loads.
The ADP2370 uses peak current-mode control with internal slope compensation, providing excellent line and load transient response across the full operating range. The internal reference is a high-accuracy bandgap with low temperature coefficient. Power-good indication, undervoltage lockout, and overcurrent protection are all integrated, reducing external component count to three (input capacitor, inductor, output capacitor). The exposed pad on the LFCSP-8 package provides a low thermal resistance path, enabling full 800 mA output even in compact designs.
Typical applications include portable and battery-powered equipment, handheld instrumentation, point-of-load regulators for FPGAs, DSPs, and microcontrollers, automotive infotainment and telematics subsystems (non-safety-critical rails), industrial control boards, and distributed power systems. The wide 3.2 V to 15 V input range accommodates single-cell Li-ion, USB, 5 V and 12 V rails, making the device particularly versatile for mixed-rail designs.
When designing with the ADP2370, select an inductor with low DCR to preserve efficiency and keep the input/output ceramic capacitors close to the IC to minimize parasitic inductance. For noise-sensitive analog loads, operate in FPWM mode to avoid PFM switching ripple; for battery-powered systems, leave PFM enabled to maximize efficiency at light load. The exposed pad must be soldered to a sufficient copper pour for thermal dissipation.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Verified distributor data is current as of 2026-10-06, and all specifications come from the Analog Devices ADP2370/ADP2371 datasheet.
Mga alternatibo na pwedeng ilagay na ADP2370ACPZ-R7 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
ADP2370ACPZ-3.3-R7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADP2370ACPZ-5.0-R7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADP2371ACPZ-R7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ADP2370ACPZ-R7
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →ADP2370ACPZ-R7 Mga Pinakamataas na Rating at Electrical Characteristics
| Topolohiya | Synchronous Buck (Step-Down) |
| Hanay ng Voltage ng Input | 3.2 V to 15 V |
| Hanay ng Output Volte | 0.8 V to 14 V (Adjustable) |
| Continuous Output Current | 800 mA |
| Takbo ng Pagpipili | 600 kHz or 1.2 MHz (FSEL selectable) |
| External Sync Range | 600 kHz to 1.2 MHz |
| Peak Efficiency | 92% (typical at 1.2 MHz, 5 V to 3.3 V) |
| Control Mode | Peak Current-Mode PWM, optional PFM at light load |
| Internal MOSFETs | Yes (high-side and low-side, integrated) |
| Output ng Power Dati | Yes |
| Soft-Start | Internal |
| Thermal Shutdown | Yes |
| Undervoltage Lockout | Yes |
| Hanay ng Temperature na Operasyon | -40C to +125C |
| Packhaging | 8-pin LFCSP-EP (CP-8-13) 3 mm x 3 mm |
| Uri ng Pagpapasok | Surface Mount |
| Level ng MSL | 3 (168 hours) |
| Tindminan RoHS | Compliant |
| Forced PWM Mode | Yes (FPWM via SYNC/MODE pin) |
Pin Configuration ng ADP2370ACPZ-R7
| Pin 1 | AGND — Analog ground reference for internal control circuitry |
| Pin 2 | VIN — Input supply voltage (3.2 V to 15 V) |
| Pin 3 | SW — Switch node - connect to power inductor |
| Pin 4 | SW — Switch node - connect to power inductor (tied to pin 3) |
| Pin 5 | PGND — Power ground return for internal low-side MOSFET |
| Pin 6 | FB — Feedback input - connect to resistor divider for adjustable VOUT |
| Pin 7 | EN — Enable input (active high) |
| Pin 8 | FSEL/SYNC — Frequency select / external sync input |
| Pin EP | EP — Exposed pad - thermal and electrical ground, must be soldered to PCB |
Tipikal na mga Gamit
ADP2370ACPZ-R7 ay nararapat para sa 6 aplikasyons: Portable Battery-Powered Equipment, Point-of-Load Regulators for MCUs and DSPs, Industrial Control and Instrumentation, Automotive Infotainment and Telematics, Distributed Power and Intermediate Bus Systems, FPGA and Processor Auxiliary Rails.
Portable Battery-Powered Equipment
The ADP2370ACPZ-R7 fits portable battery-powered equipment because its 3.2 V to 15 V input range covers single-cell Li-ion (3.7 V nominal), 5 V USB rails, and 12 V wall adapters. The low quiescent current and automatic PFM mode at light load extend battery life, while the 92% peak efficiency reduces heat in handheld designs. Placed between the battery and downstream rails (3.3 V MCU, 1.8 V sensor, 1.2 V core), the device powers handheld instruments, wireless sensor nodes, and battery-charged IoT devices. The 3 mm x 3 mm LFCSP-EP footprint preserves small PCB area.
Inirekomenda
Point-of-Load Regulators for MCUs and DSPs
The ADP2370ACPZ-R7 is well-suited as a point-of-load regulator for microcontrollers, DSPs, and FPGAs that require clean, fast-transient sub-rails. Its peak current-mode control provides excellent line and load transient response, and the integrated power-good output enables sequencing with adjacent rails. Placed adjacent to the processor's VDD pin with a 10 uF input capacitor and a 4.7 uH inductor, it produces a 1.2 V or 3.3 V core rail. The 600 kHz / 1.2 MHz frequency selection allows tuning against system noise budgets.
Inirekomenda
Industrial Control and Instrumentation
The ADP2370ACPZ-R7 fits industrial control boards because its wide 3.2 V to 15 V input range directly accepts 5 V and 12 V industrial buses, eliminating the need for upstream regulation. The -40C to +125C operating temperature range and integrated protection features (UVLO, OCP, thermal shutdown) suit factory-floor and outdoor environments. Placed on a PLC analog-input board, it powers ADC references and signal-conditioning op-amps. The exposed-pad package ensures reliable thermal performance at full 800 mA load across temperature.
Inirekomenda
Automotive Infotainment and Telematics
The ADP2370ACPZ-R7 powers non-safety-critical rails in automotive infotainment, telematics, and body-electronics modules where its 12 V input range matches vehicle bus voltages. The device is not AEC-Q100 qualified, so designers should reserve it for non-safety head units, displays, and gateway controllers rather than ADAS or chassis systems. The forced PWM (FPWM) mode maintains constant switching frequency, reducing AM-band interference in radio-equipped vehicles. Placed between the 12 V bus and downstream 5 V/3.3 V rails, it powers CAN transceivers, Bluetooth/Wi-Fi modules, and display controllers.
Inirekomenda
Distributed Power and Intermediate Bus Systems
The ADP2370ACPZ-R7 works as a downstream point-of-load converter in distributed power architectures where a 12 V intermediate bus supplies multiple local rails. Its 92% peak efficiency at 12 V to 3.3 V conversion minimizes thermal dissipation in densely populated backplanes, and its small footprint enables many parallel regulators on a single board. Placed on a PCIe card, telecom blade, or server riser, it powers local logic and memory rails. The 600 kHz operation minimizes switch-node ringing when driving long PCB traces.
Inirekomenda
FPGA and Processor Auxiliary Rails
The ADP2370ACPZ-R7 is appropriate for FPGA and processor auxiliary rails such as 1.8 V, 2.5 V, and 3.3 V where its 800 mA capacity handles moderate loads including memory banks and I/O voltage rails. Peak current-mode control yields tight regulation during load steps, important for multi-channel memory interfaces. The power-good output signals the host processor when each rail is in regulation, supporting multi-rail sequencing. Placed near the FPGA bank power pin with a 4.7 uH inductor, it provides a quiet 1.8 V supply.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ADP2370ACPZ-R7 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ADP2370ACPZ-3.3-R7 | ADP2370ACPZ-5.0-R7 | ADP2371ACPZ-R7 |
|---|---|---|---|---|
| Package | 8-pin LFCSP-EP 3x3 mm | 8-pin LFCSP-EP 3x3 mm - same | 8-pin LFCSP-EP 3x3 mm - same | 8-pin LFCSP-EP 3x3 mm - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Input Voltage Range | 3.2 V to 15 V | 3.2 V to 15 V | 3.2 V to 15 V | 3.2 V to 15 V |
| Output Voltage | 0.8 V to 14 V (Adjustable) | 3.3 V Fixed | 5.0 V Fixed | 0.8 V to 14 V (Adjustable) |
| Output Current | 800 mA | 800 mA | 800 mA | 800 mA |
| Switching Frequency | 600 kHz / 1.2 MHz (FSEL) | 600 kHz / 1.2 MHz (FSEL) | 600 kHz / 1.2 MHz (FSEL) | 600 kHz / 1.2 MHz (FSEL) |
| Peak Efficiency | 92% | 92% | 92% | 90% (lower IQ optimized) |
| Quiescent Current Profile | Standard (battery-friendly) | Standard | Standard | Ultra-low for sleep-mode |
| Output Type | Adjustable (external resistor divider) | Fixed 3.3 V | Fixed 5.0 V | Adjustable |
Pangunahing mga Pagkakaiba
- Adjustable output with widest range in 3x3 LFCSP family (kumpara saADP2370ACPZ-3.3-R7)
- Standard quiescent current optimized for most applications (kumpara saADP2371ACPZ-R7)
- Industry-standard 8-pin LFCSP footprint for easy second-sourcing (kumpara saTPS62177 (Texas Instruments))
Talaan ng Disenyo
Place the input capacitor (10 uF X7R ceramic minimum) as close to VIN and PGND pins as possible. Route the SW node traces as short and wide to minimize parasitic inductance that causes voltage ringing and EMI. Use a continuous ground plane on the layer beneath the IC, and tie the exposed pad directly to this ground plane with multiple thermal vias for heat dissipation.
Estimated: at VIN = 12 V, VOUT = 3.3 V, and IOUT = 800 mA, power dissipation is approximately (12 - 3.3) * 0.8 = 6.96 W if linear, but actual buck dissipation is roughly VIN * IQ + (VOUT / VIN efficiency factor). Real dissipation in the FETs is about 0.4 W at this operating point. At VIN = 12 V, VOUT = 1.2 V, IOUT = 800 mA, the high-side FET dissipation rises. Always design with the LFCSP-EP exposed pad soldered to a minimum 1 square inch copper pour to keep junction temperature below 125 C.
Do not operate below the 3.2 V minimum input voltage; below this threshold UVLO triggers and output collapses. Avoid using output capacitors with insufficient voltage rating - 6.3 V minimum X7R ceramic is recommended for 5 V outputs. Do not leave FB floating on the adjustable version; a floating FB pin causes output voltage to drift to the upper limit. For noise-sensitive analog loads, force PWM mode to avoid PFM ripple, accepting slightly lower light-load efficiency.
Impormasyon ng Pagsunod sa Kautusan
RoHS and lead-free compliant per Analog Devices product page. Not AEC-Q100 qualified; for safety-critical automotive applications, use a qualified equivalent from TI, NXP, or Infineon.
