AT90CAN128-15AZ - 16MHz 128KB CAN MCU | Microchip Technology
MPN: AT90CAN128-15AZ ✓ NakahandaAT90CAN128-15AZ Ulas
An 8-bit microcontroller is a compact programmable controller built around a central processing unit, memory, and dedicated peripheral interfaces. The AT90CAN128 belongs to the hierarchy of embedded microcontroller, RISC processor, semiconductor, and embedded-control device. Its AVR enhanced RISC architecture provides a practical balance of processing capability, deterministic peripherals, and low-power operation for control systems that need CAN networking rather than a high-complexity processor.
Key features include 128 KB of programmable system flash, 4 KB of EEPROM for nonvolatile data, and 4 KB of SRAM for working memory. The device provides 53 general-purpose I/O lines and 32 general-purpose working registers. Two CAN protocol versions, V2.0A and V2.0B, support industrial and automotive communication tasks, while the integrated timers, PWM-capable channels, USARTs, SPI, and two-wire serial interface reduce the need for external peripherals.
The AT90CAN128 architecture follows the AVR enhanced RISC model, with the manufacturer describing throughput approaching one million instructions per second per megahertz. At a 16 MHz operating frequency, this provides useful response bandwidth for protocol handling, supervisory control, and user-interface tasks. The combination of CAN, serial interfaces, timers, and substantial on-chip memory allows a compact control board to support real-time communication without adding substantial external logic.
Typical uses include automotive gateway controllers, industrial automation equipment, CAN-connected sensors, building-control nodes, diagnostic instruments, and compact embedded systems. The AT90CAN128-15AZ is especially appropriate when a design needs a deterministic 8-bit MCU, two-wire CAN connectivity, multiple serial interfaces, and a 64-pin surface-mount package. Its automotive-qualified ordering code also supports designs where that qualification is required.
Designers should use the pin-description table in the manufacturer datasheet when assigning board traces and should place decoupling capacitors close to the supply pins. CAN bus routing also requires a correctly implemented transceiver, termination strategy, and protection network; the MCU's CAN controller does not directly connect to a physical bus.
This product record combines manufacturer specifications, package information, and verified sourcing links to support MCU selection, pin assignment review, automotive and industrial CAN design, and drop-in replacement evaluation. It also highlights the AT90CAN128 family's clock, memory, interface, qualification, and package differences that matter when revising an existing PCB.
Mga alternatibo na pwedeng ilagay na AT90CAN128-15AZ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok AT90CAN128-15AZ (parehas na form factor at footprint) — pagkakaiba sa Package, CAN Controller, ADC, Core Architecture, Flash Memory.
AT90CAN128-15AT1
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AT90CAN128-15AT
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AT90CAN128-16AJ
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →AT90CAN128-16AU
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →AT90CAN128-16MU
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →AT90CAN128-15AZ Mga Pinakamataas na Rating at Electrical Characteristics
| Microcontroller Type | 8-bit AVR RISC microcontroller |
| Maksimum na Taktiko ng Oras | 16 MHz |
| Program Flash Memory | 128 KB |
| EEPROM Memory | 4 KB |
| SRAM | 4 KB |
| General-Purpose I/O Lines | 53 lines |
| General-Purpose Working Registers | 32 registers |
| CAN Controller | CAN V2.0A and V2.0B compliant |
| Timer and Counter Count | 4 flexible timer/counters |
| USART Count | 2 USARTs |
| Serial Interfaces | SPI and byte-oriented two-wire serial interface |
| Packhaging | 64-pin TQFP |
| Uri ng Pagpapasok | Surface mount |
| Automotive Qualification | Automotive qualified |
Gabay sa Pin Configuration ng AT90CAN128-15AZ 64-pin tqfp
Pin configuration para sa AT90CAN128-15AZ (64-pin tqfp package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa AT90CAN128-15AZ.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
AT90CAN128-15AZ ay nararapat para sa 6 aplikasyons: Automotive CAN Gateway Controller, Industrial Automation Node, CAN-Connected Sensor and Metering, Building Control and HVAC Equipment, Diagnostic and Test Equipment, Embedded Communication Controller.
Automotive CAN Gateway Controller
The AT90CAN128-15AZ fits an automotive CAN gateway because it combines a 16 MHz AVR core with a V2.0A and V2.0B CAN controller in an automotive-qualified ordering configuration. Its 128 KB of flash provides room for protocol routing, diagnostic handling, and application firmware, while 4 KB of SRAM and 4 KB of EEPROM support working state and persistent configuration. In a gateway, the MCU manages CAN frames, coordinates power or body-system status, and communicates with other modules through USART, SPI, or the two-wire serial interface. The design must still use a suitable CAN transceiver and protection network. Clock-dependent baud timing should be validated when the 15 MHz ordering code is replaced by a 16 MHz variant.
Inirekomenda
Industrial Automation Node
The AT90CAN128-15AZ is appropriate for a compact industrial automation node that communicates over CAN while executing local control logic. Its 16 MHz clock supports deterministic protocol and supervisory tasks, and the four timer/counters provide timing resources for periodic sampling, motor timing, or PWM functions. The 53 general-purpose I/O lines can distribute digital signals, while two USARTs, SPI, and a byte-oriented two-wire interface support sensors, converters, and service ports. The integrated 128 KB flash allows a unified firmware image to handle communication, diagnostics, and configuration. In deployment, maintain deterministic scheduling, validate CAN timing against the selected oscillator, and isolate field-wired nodes where the environmental design requires galvanic separation.
Inirekomenda
CAN-Connected Sensor and Metering
The AT90CAN128-15AZ suits metering and connected-sensor designs that must measure locally and publish results over a CAN network. Four kilobytes of SRAM supports transient acquisition and protocol processing, while 4 KB of EEPROM can retain calibration constants or configuration values when the application uses nonvolatile storage appropriately. Its 53 I/O lines offer flexible sensor, switch, and status inputs, and the four timer/counters support accurate sampling windows and output timing. CAN V2.0A and V2.0B compatibility lets the node participate in established industrial network architectures. Because the MCU contains a CAN protocol controller rather than a bus transceiver, the board also needs a qualified transceiver, appropriate termination, surge protection, and a defined strategy for bus-off recovery.
Inirekomenda
Building Control and HVAC Equipment
The AT90CAN128-15AZ can serve as the communications and supervisory controller in a building-control or HVAC node. Its 16 MHz processing rate and 128 KB flash are sufficient for control tables, communication maps, diagnostics, and configurable operating logic, while multiple timer/counters help generate timing signals for fans, dampers, or relays. The CAN controller supports connection to a building network, and the two USARTs plus SPI and two-wire serial interfaces permit local expansion. In this application, low-power behavior and watchdog strategy should be matched to the equipment duty cycle, and safety-related outputs must retain the protections required by the final system. Firmware should include communication timeout handling and deterministic recovery after resets or CAN error states.
Inirekomenda
Diagnostic and Test Equipment
The AT90CAN128-15AZ is useful in compact diagnostic equipment that combines CAN communication with a user interface or service link. The 128 KB flash supports firmware, lookup tables, and communication protocols, while 4 KB of EEPROM can preserve instrument settings and calibration identifiers. Two USARTs allow simultaneous connection to a host computer and a service console, and the SPI and two-wire serial interfaces can connect to displays, memories, or sensors. Four timer/counters provide timing functions for trigger generation or measurement control. Engineers should allocate bus timing consistently with the 15 MHz clock and use the manufacturer's programming and reset recommendations. For field diagnostics, implement watchdogs, error counters, and controlled recovery for both firmware faults and CAN bus errors.
Inirekomenda
Embedded Communication Controller
The AT90CAN128-15AZ fits embedded communication equipment that must bridge or manage CAN traffic alongside other serial interfaces. Its 16 MHz AVR core and 128 KB flash provide enough room for frame filtering, protocol translation, diagnostics, and application-level control. The CAN V2.0A and V2.0B controller handles the digital protocol layer, while two USARTs, SPI, and the two-wire interface offer connections to host processors, local memories, and configuration devices. Four timer/counters support timeout, heartbeat, and periodic scheduling tasks. A robust implementation should separate protocol timing from application work, monitor error counters and bus-off conditions, and select the CAN transceiver according to network speed, cable length, isolation, and environmental protection requirements.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for AT90CAN128-15AZ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | AT90CAN128-15AT1 | AT90CAN128-15AT | AT90CAN128-16AJ | AT90CAN128-16AU | AT90CAN128-16MU |
|---|---|---|---|---|---|---|
| Package | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 16 MHz | 15 MHz | 15 MHz | 16 MHz | 16 MHz | 16 MHz |
| Program Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| EEPROM Memory | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| CAN Controller | CAN V2.0A and V2.0B compliant | CAN V2.0A and V2.0B compliant | CAN V2.0A and V2.0B compliant | CAN V2.0A and V2.0B compliant | CAN V2.0A and V2.0B compliant | CAN V2.0A and V2.0B compliant |
| General-Purpose I/O Lines | 53 lines | 53 lines | 53 lines | 53 lines | 53 lines | 53 lines |
| Processor Core | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC |
Pangunahing mga Pagkakaiba
- Automotive-qualified exact ordering configuration (kumpara saAT90CAN128-16AJ)
- Higher clock margin in the same family (kumpara saAT90CAN128-15AT1)
- Integrated communication resources reduce external peripheral count (kumpara saAT90CAN128-16MU)
Talaan ng Disenyo
Use the manufacturer's 64-pin TQFP pin-description table to assign every signal and preserve access to the reset, programming, clock, and CAN-controller pins. Place all decoupling capacitors close to their associated supply and ground pins, minimize loop area, and route sensitive clock and programming nets away from CAN and switching-power-node connections. The exposed board area and thermal pattern should follow the package drawing rather than relying only on the generic TQFP outline.
The AT90CAN128 contains a CAN protocol controller, not a physical-layer transceiver. Add a transceiver whose speed, logic levels, supply range, isolation, and fault tolerance match the network. Route CAN TX and RX as a controlled differential pair with a continuous reference plane, provision the two termination resistors only where the topology requires them, and include protection that does not distort the differential signal. Firmware should also handle transmit failures, receive errors, and bus-off recovery.
Do not assume that changing between a 15 MHz and 16 MHz ordering code is transparent to existing firmware. Baud-rate generation, timer intervals, PWM periods, sampling windows, and timeout calculations may scale with the core clock. Review oscillator configuration and clock prescaling, then retest protocol timing and real-time deadlines. Also confirm the exact temperature grade, qualification, errata, and ordering suffix before replacing the exact AT90CAN128-15AZ device in an automotive or industrial production design.
Impormasyon ng Pagsunod sa Kautusan
Microchip Direct identifies the exact AT90CAN128-15AZ ordering code as automotive qualified. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact MPN.