onsemi

CD4051BCN - 8:1 CMOS Analog Multiplexer | onsemi

MPN: CD4051BCN ✓ Nakahanda
Dual V± supply Vdss 240 ohm Rds(on) 16-lead plastic dual-in-line package Package
MOQ: 1 |

CD4051BCN Ulas

onsemi CD4051BCN is an 8:1 CMOS analog multiplexer and demultiplexer with an on-state resistance of 240 ohm, housed in a 16-lead plastic dual-in-line package. It uses three binary select inputs and an inhibit control to route one of eight analog channels to a common terminal, while the same device can distribute one signal to eight destinations in demultiplexer mode. Its complementary-input structure supports signal-routing and channel-selection functions in analog and mixed-signal equipment.

An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. It belongs to the broader switched-routing and signal-path hierarchy and is commonly used to reduce the number of external connections required by analog, control, measurement, and communication systems. The CD4051BCN combines digital address selection with analog switching, allowing a microcontroller or other logic circuit to control which physical channel is connected.

The principal features include eight analog inputs, one common analog terminal, three address inputs, an inhibit input, and dual supply rails for bipolar analog operation. The manufacturer datasheet identifies low on-state impedance and very low off-state leakage as defining characteristics. Its 16-PDIP construction follows the JEDEC MS-001 package outline, making it appropriate for through-hole assemblies and legacy-compatible boards rather than compact surface-mount designs.

The three select inputs establish one of eight binary channel addresses. When the inhibit input is active, the common terminal is disconnected from the channel inputs, providing a convenient way to isolate a selected signal path. Because the control inputs are referenced to the digital supply environment while the analog path can operate across positive and negative rails, the device supports level-compatible control in many dual-supply analog systems.

Typical uses include instrumentation signal selection, data-acquisition channel routing, test-equipment control, audio path selection, and industrial control systems. The 8:1 organization is especially useful when several sensors or sources must share one amplifier, converter, display, or communications channel. System designers must also account for off-channel leakage, switching transients, and the voltage ranges allowed at each analog terminal.

For a new PCB, preserve the 16-pin DIP footprint and route analog inputs away from high-speed digital clocks and switching nodes. Confirm the supply and signal limits for the selected operating conditions, and ensure the inhibit logic cannot select an unintended channel during reset. A redesign intended for automated assembly should evaluate a surface-mount equivalent rather than assuming a DIP-to-SMD conversion is pin compatible.

This page organizes the functional architecture, control behavior, package details, drop-in options, application guidance, and design considerations into a practical engineering reference for selecting and implementing the CD4051BCN.

Mga alternatibo na pwedeng ilagay na CD4051BCN — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok CD4051BCN (parehas na form factor at footprint) — pagkakaiba sa Off-State Leakage, Package.

Texas Instruments
Off-State Leakage: ±100 pA typ at VDD-VEE = 18V
Package: 16-Pin PDIP (N)
Ikabit sa CD4051BCN →

CD4051BE

✅ Drop-In
Texas Instruments
📦 16-lead PDIP
8:1 Analog Multiplexer / Demultiplexer · 1 Circuit, 8:1 (Single Pole 8 Throw) · 240 Ohm max · 125 Ohm at VDD-VEE = 15V · 5 Ohm typ at VDD-VEE = 15V · ±100 pA typ at VDD-VEE = 18V · 15 Vp-p min at VDD-VEE = 18V · 3 V to 20 V

Magkontak para sa presyo

Tingnan ang Datasheet →

CD4051BN

✅ Drop-In
📦 16-lead PDIP
Same 8:1 multiplex/demultiplex architecture and 16-pin DIP footprint; exact suffix grade differs while the stated 240 ohm on resistance remains equal.

📋 Alternatibo na Reference (hindi sa katalogo)

TMUX4051

✅ Drop-In
📦 16-lead PDIP
Upgraded 8:1 multiplexing functionality with 1.8 V-compatible logic and extended supply capability; legacy CD4051BCN is rated at 240 ohm on resistance.

📋 Alternatibo na Reference (hindi sa katalogo)

CD4051BCN Mga Spesipikasyon

Multiplexer Configuration 8:1
On-State Resistance 240 ohm
Number of Channels 8 channels
Common Terminal Count 1 terminal
Select Input Count 3 binary inputs
Inhibit Control 1 active input
Packhaging 16-lead plastic dual-in-line package
Package Outline JEDEC MS-001
Package Width 0.300 inch
Uri ng Pagpapasok Through-hole
Supply Architecture Dual V± supply
Technology CMOS
On-State Impedance Low
Off-State Leakage Very low

Pin Configuration ng CD4051BCN

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
Pin 1 VDD — Positive supply terminal
Pin 2 IN4 — Analog input channel 4
Pin 3 IN6 — Analog input channel 6
Pin 4 IN5 — Analog input channel 5
Pin 5 IN7 — Analog input channel 7
Pin 6 IN3 — Analog input channel 3
Pin 7 IN2 — Analog input channel 2
Pin 8 IN1 — Analog input channel 1
Pin 9 IN0 — Analog input channel 0
Pin 10 COM — Common analog terminal
Pin 11 A — Binary select input A
Pin 12 B — Binary select input B
Pin 13 C — Binary select input C
Pin 14 INHIBIT — Inhibit control input
Pin 15 VEE — Negative supply terminal
Pin 16 VSS — Ground reference terminal

Tipikal na mga Gamit

CD4051BCN ay nararapat para sa 6 aplikasyons: Instrumentation Signal Selection, Data Acquisition Channel Routing, Test and Measurement Equipment, Industrial Control Signal Routing, Audio Signal Selection, Legacy Control-System Repair.

⚡

Instrumentation Signal Selection

The CD4051BCN fits instrumentation designs that must connect one of eight sensor or test signals to a shared amplifier, measurement converter, or display. Its eight analog inputs, single common terminal, and three binary address inputs reduce the number of external connections required by the host system. With a stated on-state resistance of 240 ohm, it is most appropriate when the resulting loading and insertion loss remain acceptable to the measurement accuracy. The inhibit function can isolate the common path during range changes or calibration intervals.

📊

Data Acquisition Channel Routing

The CD4051BCN can route eight analog inputs into a shared data-acquisition front end while a microcontroller applies the three select bits. The 16-PDIP package is useful for through-hole laboratory equipment and legacy control boards, while the 8:1 organization expands a single measurement chain without requiring eight separate front ends. Designers should include the 240 ohm path impedance in the source and amplifier calculations and evaluate off-channel leakage when adjacent signals differ substantially. The inhibit input provides a defined isolation point for maintenance or calibration modes.

🔧

Test and Measurement Equipment

The CD4051BCN is useful in test equipment that must connect one of several test points, sources, or return paths to a common measurement amplifier. Eight selectable inputs and three address lines allow a digital controller to organize many analog connections while retaining one common measurement path. Its 16-lead PDIP format supports traditional through-hole instrument construction and hand-built prototypes. Engineers should verify that the 240 ohm on resistance does not distort the measured quantity and that off-state leakage remains below the required error floor for the selected signal sources.

🏭

Industrial Control Signal Routing

The CD4051BCN can route different analog command or feedback signals through a shared control block in an industrial system. Its CMOS implementation, dual positive and negative supply architecture, and three digital select inputs suit systems where a controller chooses one channel for further processing. The inhibit terminal allows the controller to disconnect the common path during reset or fault conditions. For long wiring runs or noisy environments, keep the analog routes short, protect exposed inputs, and confirm that the selected switch ratings and 240 ohm impedance remain suitable for the process-control accuracy requirement.

🎧

Audio Signal Selection

The CD4051BCN may be used to select among multiple analog audio sources before an amplifier or mixer stage. Its 8:1 arrangement permits several inputs to share one downstream signal path, while the inhibit function can mute or isolate the selected route under digital control. Because the stated on-state resistance is 240 ohm, the source impedance, gain distribution, and input capacitance must be checked to prevent excessive attenuation or unintended response changes. The 16-PDIP package is particularly convenient in through-hole audio prototypes and legacy equipment repairs.

🔧

Legacy Control-System Repair

The CD4051BCN is a practical replacement target for maintaining older through-hole control equipment built around the CD4051 multiplexer family. The 16-lead PDIP footprint, three select inputs, inhibit function, and common-terminal architecture support direct board-level substitution when the selected alternative has the same pin assignments. The 8:1 capability makes it suitable for restoring old analog selection cards, test fixtures, and process-control interfaces. Before installation, verify the exact suffix grade, power rails, analog signal limits, and whether the original circuit relies on any unusual inhibit or power-up behavior.

What is the CD4051BCN?
The CD4051BCN is an 8:1 CMOS analog multiplexer and demultiplexer in a 16-lead PDIP package. According to the manufacturer datasheet, it contains eight analog channel inputs, one common terminal, three binary select inputs, and an inhibit input. It can route one of eight inputs to the common terminal or distribute a common signal to the selected output when configured for demultiplexing.
How do I select a channel on the CD4051BCN?
The CD4051BCN selects one of eight channels by applying a three-bit binary code to its A, B, and C inputs. The address combinations from 000 through 111 correspond to the eight analog inputs. An inhibit input provides an additional isolation function, while the manufacturer datasheet identifies 240 ohm as the nominal on-state resistance used to evaluate the selected analog path.
Where can I download the CD4051BCN datasheet PDF?
The CD4051BCN datasheet PDF is available through the manufacturer-family document link on this page and through the listed technical-document sources. The datasheet covers the 16-lead plastic DIP package, JEDEC MS-001 outline, 240 ohm on-state resistance, select and inhibit controls, and the recommended electrical characteristics. Use the pin-description table for PCB assignments.
Where can I find the CD4051BCN pinout?
The CD4051BCN pinout is shown by the 16-pin package diagram and can be confirmed in the manufacturer datasheet. Pin 1 is VDD, pins 2 through 9 are the eight analog inputs, pin 10 is the common terminal, pins 11 through 13 are the A, B, and C select inputs, pin 14 is inhibit, pin 15 is VEE, and pin 16 is VSS.
What are the key specifications of CD4051BCN that engineers should know?
The key CD4051BCN specifications are its 8:1 configuration, 240 ohm on-state resistance, three select inputs, inhibit function, CMOS construction, and 16-lead PDIP package. According to the manufacturer datasheet, the device also provides low on impedance and very low off-state leakage. These characteristics make it suitable for selecting one of eight analog signals in bipolar, dual-supply circuits.
Can the CD4051BCN be used as a demultiplexer?
Yes, the CD4051BCN can operate as either an 8:1 analog multiplexer or a demultiplexer. In multiplexer mode, one of eight inputs connects to the common terminal; in demultiplexer mode, a signal at the common terminal is routed to the channel selected by the three address inputs. The manufacturer datasheet describes the device specifically as a multiplexer/demultiplexer.
What can replace the CD4051BCN?
A true drop-in replacement must use the same 16-lead PDIP footprint and preserve the select, inhibit, supply, analog-input, and common-terminal assignments. CD4051BE and CD4051BN are the supported alternatives identified for that role, while TMUX4051 offers upgraded functionality but has different packaging options. Confirm the exact package and control logic before replacing any installed device.
Is the CD4051BCN the same as CD4051BE?
The CD4051BCN and CD4051BE implement the same 8:1 analog multiplexer/demultiplexer function in a 16-lead PDIP package, with 240 ohm on-state resistance. Their ordering codes distinguish the temperature grade or qualification treatment, so the manufacturer datasheet for each exact suffix should be checked before substitution. The CD4051BE is a supported same-footprint alternative.
When should I choose CD4051BCN over a modern multiplexer?
Choose the CD4051BCN when maintaining a through-hole legacy design, using a 16-PDIP footprint, and requiring a conventional 8:1 control interface. Retain it when its 240 ohm on-state resistance is adequate and a qualified modern alternative would introduce different pin assignments, supply requirements, or package dimensions. For new surface-mount designs, compare the electrical trade-offs of current multiplexers before selecting a replacement.
Is CD4051BCN suitable for instrumentation signal routing?
The CD4051BCN is suitable for instrumentation signal routing when its 240 ohm on-state resistance and leakage characteristics meet the measurement accuracy budget. It offers eight selectable analog inputs in a 16-lead PDIP package, allowing several sensors to share a downstream amplifier or converter. Verify input bandwidth, charge injection, off-state leakage, and allowable signal voltage for the specific measurement.
What is the best onsemi equivalent for CD4051BCN?
The onsemi CD4051BE is the closest listed equivalent for a 16-lead PDIP footprint because it retains the 8:1 multiplexer/demultiplexer architecture and 240 ohm on-state resistance. The onsemi CD4051BN is another same-family option identified by the package and suffix pattern. Check the exact ordering code, temperature grade, and lifecycle status before approving either replacement.
Where can I buy CD4051BCN online?
Use the Request a Quote form on this page to ask for CD4051BCN availability, current lead time, and order quantities. The component is an onsemi 16-PDIP analog multiplexer, so quote details should include the exact CD4051BCN suffix and required shipment quantity. Requesting a formal quote avoids relying on a stale distributor listing or an incorrect package variant.
What is the price of CD4051BCN?
Current CD4051BCN commercial terms are handled through the Request a Quote form on this page. Enter the quantity, target packaging, and delivery requirements to obtain a current response. The manufacturer listing identifies the part as a 16-PDIP, 8:1, 240 ohm multiplexer, allowing the quotation request to be tied to the exact device and package.
What is the lead time for CD4051BCN?
The current CD4051BCN lead time and available stock should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, packaging, shipment destination, and market conditions. Include the exact 16-PDIP ordering code CD4051BCN in the request so the supplier can confirm the correct component rather than a related multiplexer suffix.
Is CD4051BCN in stock?
Current CD4051BCN stock status should be confirmed through the Request a Quote form on this page. The onsemi product listing identifies the part as an 8:1 analog switch with 240 ohm on-state resistance in a 16-PDIP package, but live quantity confirmation requires a quotation response. State the required quantity and target date in the request.

Impormasyon ng Talumpati sa Engineering for CD4051BCN — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the CD4051BCN when maintaining or reproducing a 16-lead PDIP design that requires an 8:1 CMOS analog multiplexer, three select inputs, an inhibit function, and a 240 ohm on-state resistance. It is particularly appropriate for legacy industrial controls, laboratory instruments, audio routing, and test fixtures through which through-hole assembly is acceptable. CD4051BE is the preferred same-family choice when procurement qualification calls for that suffix while retaining the same footprint and channel architecture. CD4051BN offers another matched 16-PDIP option when its exact grade is approved. TMUX4051 is appropriate when upgraded functionality, 1.8 V-compatible control, or broader supply capability is more important than preserving the traditional CD4051 implementation. For any substitution, confirm pin assignments, inhibit polarity, operating temperature, supply limits, analog-node limits, leakage, and channel impedance against the exact manufacturer datasheet.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto CD4051BE CD4051BN TMUX4051
Package 16-lead PDIP 16-lead PDIP 16-lead PDIP 16-lead PDIP
Brand onsemi onsemi onsemi Texas Instruments
Multiplexer Configuration 8:1 8:1 8:1 8:1
Mounting Type Through-hole Through-hole Through-hole Through-hole
Supply Architecture Dual V± supply Dual V± supply Dual V± supply Extended bipolar and positive supply capability
Logic Compatibility Logic-level conversion Logic-level conversion Logic-level conversion 1.8 V-compatible logic
Analog Signal Capability Bipolar analog multiplexing Bipolar analog multiplexing Bipolar analog multiplexing ±24 V multiplexing

Pangunahing mga Pagkakaiba

  • Legacy-compatible 16-pin through-hole implementation (kumpara saTMUX4051)
  • Eight-channel routing in one component (kumpara saCD4051BE)
  • Consistent 240 ohm on-state resistance (kumpara saCD4051BN)

Talaan ng Disenyo

Treat the selected analog path as a resistance-controlled route with a stated 240 ohm on-state impedance. Include that value together with the source impedance, amplifier input resistance, cable capacitance, and switching transients when setting gain and bandwidth. For precision measurements, evaluate leakage and channel-to-channel crosstalk at the actual operating temperature rather than relying only on the nominal 8:1 configuration.

Keep the eight analog inputs and the common terminal on a compact, continuous trace region, and separate them from clocks, relay contacts, and switching power nodes. Maintain a stable ground reference between VSS and the analog source. For a new through-hole design, reserve the 16-pin PDIP footprint and include the dual supply connections even when one rail is used at zero volts.

Do not treat an 8:1 multiplexer as a zero-drop connection: the selected path introduces 240 ohm on resistance, and the unselected inputs can influence common-mode and leakage behavior in the connected circuit. Confirm the inhibit polarity and startup state in firmware, and verify every analog-node voltage against the manufacturer limits before energizing the board.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ordering code.

Data napatotohanan sa: 2026-11-10 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

cd4051bcn datasheet CD4051BCN datasheet pdf CD4051BCN pinout CD4051BCN equivalent CD4051BCN replacement CD4051BCN cross reference CD4051BCN vs CD4051BE CD4051BCN vs TMUX4051 onsemi CD4051BCN CD4051BCN 8:1 multiplexer CD4051BCN 240 ohm CD4051BCN 16-PDIP CD4051BCN price CD4051BCN stock CD4051BCN analog switch application

Mga kaugnay na Mga Komponente at mga Tuntunin

onsemi Fairchild Semiconductor CD4051BCN CD4051BE CD4051BN TMUX4051 analog multiplexer analog demultiplexer 8:1 multiplexer CMOS interface IC semiconductor analog switch common terminal binary select input inhibit control on-state resistance off-state leakage dual supply JEDEC MS-001 16-lead PDIP through-hole package dual in-line package logic-level conversion
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ