DS90CR563MTD - 65MHz LVDS 18-Bit FPD-Link Transceiver
MPN: DS90CR563MTD ✓ NakahandaDS90CR563MTD Ulas
An FPD-Link transceiver is an interface IC that converts parallel pixel data to a low-voltage differential signaling data stream and receives differential data back from a display panel. It belongs to the FPD-Link interface family, within the broader category of interface ICs and digital semiconductors. LVDS reduces signal amplitude while preserving high data throughput, making it suitable for point-to-point connections between a display timing controller and a panel receiver over cables or board-level interconnects.
The verified source data identifies the principal operating features as LVDS signaling, 18-bit color data support, a 65 MHz link clock, 21 driver outputs, 3 receiver inputs, and a 48-pin TSSOP package. These parameters distinguish the device as a multi-channel display-interface solution rather than a general-purpose logic IC. Its transmitter and receiver count also indicates that it is intended for full digital video links carrying pixel data and control information.
Technically, the DS90CR563MTD integrates parallel-to-differential and differential-to-parallel conversion into one package. The 65 MHz operating point supports the stated 18-bit color FPD-Link function, while the 21:3 transmit-to-receive arrangement supports simultaneous transfer in both directions. Exact voltage ratings, current consumption, propagation delay, differential impedance, temperature range, and connector or panel-termination recommendations were not present in the verified excerpts and therefore require confirmation from the manufacturer datasheet.
Typical uses include LVDS flat-panel monitor links, digital signage interfaces, industrial display controllers, automotive passenger-information displays, and embedded human-machine-interface panels. For these systems, the key selection criteria are the 48-TSSOP footprint, 18-bit color width, 65 MHz clocking, and compatibility with the panel’s LVDS input architecture. System designers must also verify connector assignment and panel timing requirements.
The primary layout consideration is the dense 48-pin TSSOP footprint. Place the device according to the datasheet pin configuration and provide the differential routing, ground reference, decoupling, and display-link topology recommended for the application. Do not assume compatibility with a different panel simply because both products use LVDS; data mapping, clocking, voltage levels, and connector assignments must be checked.
This product record combines verified device classification, package information, link width, clock rate, distributor listings, and practical replacement guidance. It also identifies where missing electrical and mechanical details must be obtained, preventing unsupported assumptions during schematic review, PCB layout, and production procurement.
Mga alternatibo na pwedeng ilagay na DS90CR563MTD — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboDS90CR563MTD Mga Spesipikasyon
| Product Type | LVDS FPD-Link transceiver |
| Data Width | 18 bits |
| Maksimum na Taktiko ng Oras | 65 MHz |
| Signal Standard | LVDS |
| Transmitter Count | 21 outputs |
| Receiver Count | 3 inputs |
| Packhaging | 48-pin TSSOP |
| Uri ng Pagpapasok | Surface mount |
| Primary Application | 18-bit color flat-panel display FPD-Link |
Gabay sa Pin Configuration ng DS90CR563MTD 48-pin tssop
Pin configuration para sa DS90CR563MTD (48-pin tssop package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa DS90CR563MTD.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
DS90CR563MTD ay nararapat para sa 6 aplikasyons: Computer Monitor FPD-Link, Industrial Panel Display Interface, Digital Signage Controller, Automotive Passenger Information Display, Embedded Human-Machine Interface, Video Processing and Test Equipment.
Computer Monitor FPD-Link
The DS90CR563MTD fits a flat-panel monitor link that transfers 18-bit color data at a 65 MHz LVDS clock. Its 21 transmitter outputs and 3 receiver inputs support a bidirectional display-interface arrangement between a graphics timing controller and a panel receiver. Using a device identified specifically for 18-bit color FPD-Link operation simplifies initial panel-interface assessment. The designer must still match connector pins, panel data order, sync signals, input voltage, and differential termination before fabrication. Because the verified excerpts omit propagation-delay, supply-voltage, and recommended-layout details, those values should be obtained from the manufacturer datasheet and validated in the target monitor electronics.
Industrial Panel Display Interface
The DS90CR563MTD is applicable to industrial HMIs and control panels that use a compatible 18-bit LVDS display channel operating at 65 MHz. The dedicated FPD-Link function provides a defined alternative to implementing pixel-to-differential conversion with multiple discrete components. Its 48-pin TSSOP package requires careful fanout and matched routing, while the verified 21/3 channel arrangement should be compared directly with the panel receiver. Industrial environments also make grounding, ESD protection, temperature qualification, and lifecycle verification important. Those electrical and environmental limits were not present in the supplied search excerpts and must be confirmed from the manufacturer document rather than inferred.
Digital Signage Controller
A digital signage controller can use the DS90CR563MTD when the selected display panel accepts an 18-bit color LVDS FPD-Link signal at 65 MHz. The device consolidates differential transmission and reception functions into one 48-pin TSSOP transceiver, supporting a point-to-point display architecture with reduced external interface circuitry. The key engineering checks are channel mapping, timing compatibility, cable length, connector assignment, and panel-side input thresholds. Because the supplied sources do not state cable-length limits or receiver sensitivity, the design should not be released until those parameters are confirmed from the authoritative datasheet and the display vendor's interface specification.
Automotive Passenger Information Display
The DS90CR563MTD can serve as the display-link transceiver in an automotive passenger-information system when the target LCD uses a compatible 18-bit LVDS FPD-Link architecture at 65 MHz. Its integrated 21 transmitter outputs and 3 receiver inputs make it suitable for exchanging pixel and control data between a video controller and display module. Automotive use requires separate verification of AEC-Q100 status, operating temperature, transient immunity, ESD behavior, and fault monitoring because those details were not included in the verified excerpts. The final design must also comply with the vehicle display connector and OEM validation requirements rather than relying only on generic LVDS signaling.
Embedded Human-Machine Interface
The DS90CR563MTD is suitable for an embedded human-machine interface panel when the graphics engine and LCD module use a compatible 18-bit color FPD-Link clocked at 65 MHz. Integrating the transmit and receive functions in one 48-pin TSSOP device can simplify the panel-facing subsystem compared with separate serializer and deserializer components. Integration still requires a careful lane-by-lane data map, synchronization of enable or timing signals, and verification of the panel's differential input network. The verified excerpts do not provide I/O capacitance, input current, or timing margins, so signal-integrity simulation should use values obtained directly from the manufacturer datasheet.
Video Processing and Test Equipment
The DS90CR563MTD can be evaluated in video-interface test equipment that reproduces an 18-bit, 65 MHz LVDS FPD-Link connection between a source controller and a panel emulator. This application allows engineers to validate the target's 21/3 transceiver arrangement in a controlled fixture before integrating it into a finished display. The fixture should use the manufacturer's specified pinout, supply sequencing, test patterns, and LVDS termination network rather than a generic connector arrangement. A panel emulator must reproduce the receiver's expected impedance and loading, while instrumentation should account for the source's differential signaling and timing. Exact test conditions were not included in the verified data and require the manufacturer datasheet.
Impormasyon ng Talumpati sa Engineering for DS90CR563MTD — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Package | 48-pin TSSOP |
| Brand | National Semiconductor |
| Data Width | 18 bits |
| Maximum Clock Frequency | 65 MHz |
| Signal Standard | LVDS |
| Transmitter Count | 21 outputs |
| Receiver Count | 3 inputs |
| Product Type | 18-bit color FPD-Link transceiver |
Pangunahing mga Pagkakaiba
- Dedicated 18-bit color display-interface configuration (kumpara saGeneric 18-bit LVDS transceiver)
- Integrated bidirectional link functions (kumpara saSeparate serializer and deserializer approach)
- Established 65 MHz display-link operating point (kumpara saLower-rate LVDS transceiver)
Talaan ng Disenyo
Route each LVDS differential pair as a coupled pair with continuous reference-plane clearance and avoid stubs, vias, or split planes where practical. Keep the DS90CR563MTD close to the display connector and place any panel-side termination network where the manufacturer datasheet shows it. The verified excerpts do not provide a reference LVDS impedance or trace-spacing recommendation, so these values must come from the authoritative interface specification rather than a generic FPD-Link rule.
Use the 48-pin TSSOP land pattern and pin numbering from the manufacturer datasheet exactly. Confirm which pins are power, ground, transmit channels, receive channels, clock, and control functions before fanout; a generic 48-pin library footprint is insufficient for assigning signals. Place required bypass capacitors at the corresponding pins, provide an uninterrupted ground reference, and verify exposed or thermal requirements from the package drawing.
Do not treat every 18-bit LVDS transceiver as interchangeable with the DS90CR563MTD. Drop-in use requires the same 48-pin TSSOP footprint, 21 transmitter outputs, 3 receiver inputs, 18-bit data organization, 65 MHz operation, compatible electrical levels, and matching panel data mapping. Also verify connector assignments and control-signal polarity. The supplied cross-reference results did not establish a confirmed pin-compatible substitute, so unverified replacement parts can damage display links or create subtle timing errors.
Validate the complete source-to-panel link with the final cable, connector, and receiver loading rather than assuming compliance from the 65 MHz label alone. Check differential voltage, input thresholds, propagation delay, channel-to-channel skew, clock jitter, and panel data timing using the values in the manufacturer datasheet. Because exact timing and jitter limits were not present in the verified excerpts, use an eye diagram or equivalent receiver tolerance analysis with authorized device parameters.
Impormasyon ng Pagsunod sa Kautusan
The verified web excerpts do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These statuses require confirmation from the current manufacturer product page or an authorized distributor record.
