LM2904FVM-GTR - Dual Ground-Sense Op Amp | ROHM
MPN: LM2904FVM-GTR ✓ NakahandaLM2904FVM-GTR Ulas
An operational amplifier is an analog amplifier IC that uses feedback to amplify the difference between two input voltages. The dual configuration integrates two amplifier channels into one package, reducing board area in designs that need more than one amplification stage. Within the broader semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and linear IC families, where it supports precision control, measurement, buffering, and signal-conditioning functions.
The ground-sense architecture is suited to circuits that monitor or condition signals referenced toward ground. The two independent channels can be used separately or together in applications such as current-sense amplifiers, low-side sensing, sensor interfaces, and general feedback-control blocks. The 3 V to 32 V single-supply range permits operation from compact 3 V systems through substantially higher industrial supply rails, provided the complete circuit remains within the device operating limits.
Low current consumption makes the LM2904FVM useful in designs where the amplifier must coexist with battery-powered, portable, or broadly distributed sensing circuitry. Its MSOP-8 package supports compact surface-mount assembly, while the dual channel count reduces the number of packages needed compared with two single operational amplifiers. Engineers should still verify output-current demand, input common-mode range, output swing, noise, offset, and stability requirements against the manufacturer datasheet for the intended application.
Typical uses include amplifying the voltage across a low-side shunt, conditioning resistive sensor outputs, and providing gain around analog-control loops. The amplifier can also serve as a buffer when its input bias and noise characteristics meet the system requirements. In each circuit, resistor values should establish suitable gain while keeping the operating point within the device input and output ranges.
For PCB implementation, place the device close to the signal source and receiver to minimize susceptibility to noise and parasitic loading. Keep high-current switching paths away from input and feedback nodes, provide a stable decoupling capacitor at the supply pins, and route the feedback loop compactly. Confirm stability with the selected gain and output-load configuration rather than assuming that a generic compensation arrangement fits every application.
This page organizes the LM2904FVM-GTR for engineers evaluating dual ground-sense amplifier requirements, including its 3 V to 32 V supply range, 8-MSOP format, use cases, sourcing considerations, and the engineering checks needed before committing a PCB footprint. Use the manufacturer product page and datasheet for final electrical, environmental, and ordering validation.
Mga alternatibo na pwedeng ilagay na LM2904FVM-GTR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboLM2904FVM-GTR Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Dual ground-sense operational amplifier |
| Number of Channels | 2 circuits |
| Single-Supply Operating Voltage Range | 3 V to 32 V |
| Total Supply Voltage Range | ±16 V / 32 V |
| Packhaging | 8-MSOP |
| Uri ng Pagpapasok | Surface mount |
| Delivery Form | Tape & Reel (TR) |
| Current Consumption | Low current consumption |
| Input and Output Ground Sense | Supported |
Gabay sa Pin Configuration ng LM2904FVM-GTR 8-msop
Pin configuration para sa LM2904FVM-GTR (8-msop package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM2904FVM-GTR.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM2904FVM-GTR ay nararapat para sa 6 aplikasyons: Low-Side Shunt Current Sensing, Resistive Sensor Signal Conditioning, Battery-Powered Monitoring, Industrial Control Signal Amplification, Analog Feedback Control, Ground-Referenced Voltage Buffering.
Low-Side Shunt Current Sensing
LM2904FVM-GTR fits low-side current sensing because its ground-sense architecture is intended for signals referenced toward ground and its two channels can amplify a shunt voltage in a compact 8-MSOP package. The amplifier can be placed between the shunt and a controller, ADC, or comparator to raise a small differential measurement above the usable signal range. The 3 V to 32 V single-supply range allows the same device to serve low-voltage and higher-voltage sensing systems. Before layout, confirm that the shunt-induced input voltage remains inside the common-mode range and that the selected feedback resistors keep the output within its permitted swing. Include the shunt tolerance, amplifier offset, and measurement bandwidth in the error budget.
Inirekomenda
Resistive Sensor Signal Conditioning
The LM2904FVM-GTR is suitable for conditioning resistive sensor outputs where a divider produces a ground-referenced voltage that requires amplification before digitization. Its dual configuration can process complementary or related sensor channels, while the low current consumption helps limit the burden on a compact sensing system. A 3 V minimum supply supports low-energy operation, and the 32 V upper limit provides room for higher-voltage industrial designs. Choose resistor values that keep the sensor bridge and amplifier input within their valid common-mode range. Account for input offset when resolving small changes, and verify output headroom at the highest sensor value. The manufacturer datasheet should determine whether the selected gain and loading meet the required accuracy and bandwidth.
Inirekomenda
Battery-Powered Monitoring
LM2904FVM-GTR fits portable monitoring equipment when low current consumption and a 3 V minimum operating voltage are important. Its two ground-sense channels can support compact measurement blocks that monitor current, temperature-derived analog signals, or other ground-referenced conditions. The 8-MSOP format reduces PCB area, and the single-supply range permits operation from a 3 V system without a negative rail. Because the amplifier can remain connected continuously, verify the quiescent current and the additional supply demand created by the selected feedback network. Power-gate the input or measurement path when the application requires longer standby time, and ensure the input common-mode range remains valid throughout battery discharge and recharge transients.
Inirekomenda
Industrial Control Signal Amplification
LM2904FVM-GTR can amplify low-level control signals in industrial equipment requiring a single supply and a ground-referenced input arrangement. Its 3 V to 32 V operating range covers systems where the control rail can vary across the operating envelope, while two channels can support gain stages, comparators, or actuator-driver input conditioning. The MSOP-8 package helps reduce board area in dense control assemblies. Design the feedback network around the required closed-loop gain, then verify output swing, common-mode range, and stability. Maintain separation between analog input routing and switching power stages. For factory equipment, check the operating-temperature limits and environmental qualification in the manufacturer documentation before using the device in safety-related or high-temperature locations.
Inirekomenda
Analog Feedback Control
The two channels of LM2904FVM-GTR can be assigned to independent analog feedback functions in control and regulation circuits. The ground-sense capability supports signals whose useful operating point lies near ground, while the broad 3 V to 32 V supply range supports both compact and industrial control rails. One channel may amplify an error or sensing signal, and the other may support an auxiliary signal path. Feedback-loop stability remains dependent on the amplifier gain, load, output impedance, and compensation network, so evaluate the final topology rather than relying on the amplifier family name. Keep feedback traces short, provide local supply decoupling, and verify startup behavior over the complete input and load ranges.
Inirekomenda
Ground-Referenced Voltage Buffering
LM2904FVM-GTR can buffer ground-referenced voltages when a source cannot drive the following stage directly. Its dual-channel construction allows two buffers to share one compact package, and its 3 V to 32 V single-supply operation accommodates a wide range of system rails. A unity-gain buffer configuration still requires verification of input offset, bias current, output capability, and stability with the attached load. Place each buffer close to the source or destination it serves, avoid long high-impedance input routes, and maintain a low-impedance ground return. This arrangement is especially useful for sensor nodes and control interfaces where ground noise or loading would otherwise degrade measurement accuracy.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM2904FVM-GTR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Amplifier Type | Dual ground-sense operational amplifier |
| Number of Channels | 2 circuits |
| Single-Supply Operating Voltage Range | 3 V to 32 V |
| Total Supply Voltage Range | ±16 V / 32 V |
| Ground-Sense Operation | Input and output ground sense |
| Current Consumption | Low current consumption |
| Package | 8-MSOP |
| Brand | ROHM Semiconductor |
Pangunahing mga Pagkakaiba
- Ground-sense dual-amplifier architecture (kumpara saGeneral-purpose LM2904 family devices)
- Wide single-supply operating range (kumpara saTI LM2904)
- Low-current dual-channel integration (kumpara saTwo single-channel operational amplifiers)
Talaan ng Disenyo
Place the input, output, feedback, and supply connections with short, direct traces. Put the supply-decoupling capacitor immediately beside the power pins and provide a low-impedance ground return. Sensitive input nodes should remain away from switching inductors, power stages, and high-current return paths because capacitive coupling can appear as measurement error even when the amplifier itself operates correctly.
Do not assume that every LM2904-family device is a mechanical substitute. The footprint, exposed-pad arrangement, pin numbering, input assignment, common-mode range, and output-swing limits must match. Compare the manufacturer pin table and electrical characteristics before replacing LM2904FVM-GTR, especially when moving between MSOP, SOIC, and other package styles.
For shunt and sensor measurements, keep the amplifier input route short and preserve a continuous reference ground. Calculate the maximum shunt voltage, offset contribution, and output swing before fixing the gain. Use the manufacturer datasheet to confirm input bias current, offset voltage, noise, bandwidth, and capacitive-load stability under the actual source impedance and feedback network.
The 3 V to 32 V single-supply capability does not imply that every input and output combination is valid at 3 V. Check the common-mode and output-swing requirements across the lowest, nominal, and highest supply conditions. In battery systems, include startup, load-dump, and recharge transients when selecting the supply range and local decoupling.
Impormasyon ng Pagsunod sa Kautusan
Compliance status must be confirmed from the current ROHM product declaration or material-compliance documentation before production release.
