LM2904VDMR2 - Dual 3-32V Op Amp for Industrial Control
MPN: LM2904VDMR2 ✓ NakahandaLM2904VDMR2 Ulas
An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, compare voltages, and implement active analog filters. The dual LM2904 family combines two amplifiers in one package, reducing board area compared with separate single amplifiers. Its ability to operate from a single positive supply or from split positive and negative rails gives it broad utility in both grounded-signal systems and bipolar analog environments.
Key features include low power drain, a 1 MHz gain-bandwidth product, and a common-mode input range that extends to ground or VEE. The 3 V to 32 V operating range supports both conventional 5 V and 24 V industrial systems when the total supply remains within the rated range. The 8-MSOP surface-mount package also supports compact, high-density analog boards while providing adequate lead spacing for automated assembly and inspection.
The LM2904 architecture derives from the circuit design used in onsemi's quad operational-amplifier family. It is intended for general-purpose applications where low power consumption and flexible supply configurations are more important than precision, rail-to-rail input/output performance, or the bandwidth of modern CMOS amplifiers. Because the input common-mode range can reach ground or VEE, the device can process signals near the lower supply rail when correctly biased.
Typical applications include 0–5 V or 0–10 V industrial sensor interfaces, low-level transducer amplification, analog alarm and threshold circuits, active low-pass filters, and general control-signal conditioning. It may also be used in battery-powered instrumentation where the selected operating point must balance signal bandwidth against power drain. Split-supply operation is useful for bipolar sensor signals or analog stages that require both positive and negative swing around ground.
When designing around the LM2904VDMR2, verify input and output voltage limits at the selected supply voltage and load. Input and output decoupling should be placed close to the device, and unused amplifier channels must be configured according to the manufacturer’s recommended stable operating conditions. Avoid relying on rail-to-rail behavior, and account for input offset and bias-current errors when designing high-accuracy signal chains.
This product page consolidates the confirmed supply, bandwidth, package, and application characteristics with drop-in replacement analysis, package comparison, and practical circuit guidance. It helps engineers distinguish genuine footprint-compatible options from amplifiers that are only functionally similar before committing a new board revision.
Mga alternatibo na pwedeng ilagay na LM2904VDMR2 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
LM2904DMR2
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM2904VDMR2 Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Dual operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Supply Voltage Range | 3 V to 32 V |
| Alternate Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1 MHz |
| Common-Mode Input Range | Extends to ground or VEE |
| Supply Configuration | Single supply or split supply |
| Power Consumption | Low power drain |
| Hanay ng Temperature na Operasyon | -25 °C to +85 °C |
| Packhaging | Micro-8 |
| Package Type | 8-MSOP |
| Bilang ng Pins | 8 pins |
| Uri ng Pagpapasok | Surface mount |
| Amplifier Classification | Standard general-purpose amplifier |
Gabay sa Pin Configuration ng LM2904VDMR2 8-msop
Pin configuration para sa LM2904VDMR2 (8-msop package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM2904VDMR2.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM2904VDMR2 ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, 0–10 V Control Signal Buffering, Transducer and Sensor Interface, Active Low-Pass Filter, Threshold and Alarm Detection, Split-Supply Analog Front End.
Industrial Sensor Signal Conditioning
The LM2904VDMR2 is appropriate for amplifying low-level industrial sensor signals because it provides two channels, a 1 MHz gain-bandwidth product, and a confirmed 3 V to 32 V supply range. A typical circuit uses one channel for non-inverting amplification and the other for an active filter or reference stage. Its common-mode input range extending to ground or VEE is useful when the sensed voltage lies near the lower rail. Designers should still calculate closed-loop gain against the 1 MHz bandwidth and verify that input and output operating points remain within the electrical limits.
Inirekomenda
0–10 V Control Signal Buffering
LM2904VDMR2 can buffer and condition a 0–10 V industrial control signal when the system operates from a compatible single supply. The 1 MHz gain-bandwidth product provides ample bandwidth for slow control-loop signals, while the two amplifier channels allow one stage to buffer the input and another to perform scaling or filtering. Because the common-mode range extends toward ground or VEE, the circuit can accommodate input signals near the lower supply rail. The final design must confirm output swing, load capability, stability with the selected feedback network, and operation throughout supply tolerance.
Inirekomenda
Transducer and Sensor Interface
The LM2904VDMR2 fits transducer interfaces that operate from a 5 V to 24 V supply and require two analog channels on one package. One amplifier can provide gain around a resistive sensor bridge, while the other can buffer the result or form an active low-pass filter. Its common-mode input range extending to ground or VEE helps with sensors whose output is close to the lower rail. The 3 V to 32 V operating range supports industrial supply variants, but input bias current, offset voltage, output drive, and noise must be checked against the sensor impedance and required measurement accuracy.
Inirekomenda
Active Low-Pass Filter
The LM2904VDMR2 can implement a second-order active low-pass filter when both amplifier channels are assigned to the filter topology. Its 1 MHz gain-bandwidth product provides a practical basis for choosing closed-loop gains and component values, while the 8-MSOP package keeps the implementation compact. The supply range of 3 V to 32 V permits operation from a 5 V rail or an appropriately protected 24 V system. Filter performance remains dependent on resistor tolerances, capacitor selection, output loading, and amplifier stability, so the final transfer function should be simulated before release to manufacturing.
Inirekomenda
Threshold and Alarm Detection
LM2904VDMR2 is well suited to threshold and alarm detection because its common-mode input range can extend to ground or VEE and its supply range reaches 32 V. A comparator-style application can compare a sensor voltage against a reference, with the second channel available for reference buffering or hysteresis shaping. The 1 MHz gain-bandwidth product is sufficient for many slow industrial alarms and avoids the bandwidth limits of very low-frequency comparators. The circuit must include suitable output pull-up or load arrangements, verify input common-mode limits, and account for offset voltage so the switching threshold remains repeatable.
Inirekomenda
Split-Supply Analog Front End
The LM2904VDMR2 can process bipolar signals when the board provides positive and negative rails because the amplifier explicitly supports split-supply operation. Both channels can be used for instrumentation-style gain and filtering stages without changing to a rail-to-rail device, provided the signal remains inside the common-mode range. The 3 V to 32 V figure describes the total supported supply condition, so the rail allocation and negative-rail magnitude must be taken from the manufacturer electrical characteristics. Decoupling, input protection, and output-swing verification are especially important when the input approaches either supply rail.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM2904VDMR2 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM2904DMR2 |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 8-MSOP | 8-MSOP |
| Product Type | Dual operational amplifier | Dual operational amplifier |
| Number of Channels | 2 channels | 2 channels |
| Mounting Type | Surface mount | Surface mount |
Pangunahing mga Pagkakaiba
- Higher confirmed upper supply rating (kumpara saTI LM2904)
- Higher gain-bandwidth product (kumpara saTI LM2904)
- Compact dual-amplifier integration (kumpara saLM2904P3)
Talaan ng Disenyo
Place the input and output bypass capacitors close to the corresponding power pins and route each return current directly to the device ground or supply-reference plane. Keep sensitive input traces short, avoid routing them alongside switching-node or high-current traces, and use a continuous ground reference beneath the analog section. The 8-MSOP package has fine lead spacing, so verify pad dimensions, solder-mask clearance, and assembly capability against the manufacturer package drawing before releasing the PCB.
Do not assume rail-to-rail input or output behavior. Check the common-mode input range against the actual signal and supply levels, especially when operating near ground or VEE. For each channel, use the manufacturer’s recommended configuration when the output is unused, account for output loading, and avoid creating feedback networks that approach the device’s stability limits. The 1 MHz gain-bandwidth product should be used as the basis for closed-loop bandwidth calculations rather than treated as unlimited signal bandwidth.
The confirmed operating range is 3 V to 32 V, but industrial 24 V rails can exceed nominal voltage during transients. Analyze the maximum rail voltage, supply tolerance, and switching spikes before connecting the device. Decoupling close to the package helps control supply noise, while external clamping may be required in long cables or inductive environments. Separate the 24 V input path from sensitive signal routing so common-mode supply noise is not injected into the amplifier inputs.
Impormasyon ng Pagsunod sa Kautusan
The LM2904VDMR2 is a general-purpose commercial operational amplifier rather than an AEC-Q100-qualified automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the cited product information.
