LPC1778FBD208K - 120MHz Cortex-M3 MCU with 512KB Flash | NXP
MPN: LPC1778FBD208K ✓ NakahandaLPC1778FBD208K Ulas
A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripheral interfaces on one integrated circuit. The LPC1778 belongs to the Arm Cortex-M3 microcontroller, 32-bit embedded-controller, and integrated-circuit hierarchy. Its Cortex-M3 core operates at up to 120 MHz, allowing real-time control and network-oriented embedded workloads to share one controller while reducing the number of discrete components required on the board.
Key features include 512 kB of flash for firmware, 96 kB of SRAM for working memory, and the extensive communication peripheral set listed by NXP. The integrated Ethernet and USB 2.0 interfaces support connected equipment without requiring separate controllers. Five UARTs, two CAN channels, three SSP/SPI interfaces, three I2C interfaces, and I2S provide options for sensors, displays, industrial buses, storage, audio, and communications links. The 8-channel 12-bit ADC and 10-bit DAC support mixed-signal measurement and control.
The 208-pin LQFP package exposes the device’s broad I/O and interface resources, including Ethernet, USB, CAN, serial buses, analog channels, motor-control signals, and external-memory interfaces. This high pin count is valuable when a system needs many independently connected peripherals without multiplexing several functions through a smaller package. Its 32-bit architecture and 120 MHz operating frequency provide ample compute performance for protocol handling, data acquisition, motor control, and supervisory tasks.
Typical uses include industrial automation and factory equipment, networked embedded controllers, USB-to-Ethernet gateways, motor-control systems, data-acquisition equipment, and communications infrastructure. Ethernet and USB make it appropriate for supervisory controllers or gateways, while the CAN, serial, and analog interfaces can connect sensors and actuators. The integrated ADC, DAC, QEI, and motor-control features also suit position and closed-loop control applications.
A critical design consideration is the 208-pin package’s routing and decoupling requirements. Place the required power and bypass capacitors close to their associated supply pins, provide a clean 3.3 V rail as identified by the verified distributor information, and route high-speed Ethernet and USB signals with controlled impedance and continuous reference planes. Firmware should also validate startup, clock configuration, memory mapping, and peripheral initialization before enabling external actuators.
This page consolidates verified NXP and distributor information, interface details, application fit, and design guidance into one engineering-focused product record. It also distinguishes exact drop-in alternatives from broader functional equivalents, helping procurement and engineering teams avoid treating pin-compatible replacements and redesign-level substitutions as interchangeable.
Mga alternatibo na pwedeng ilagay na LPC1778FBD208K — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
LPC1778FBD208
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
LPC1778FBD208K Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 32-bit microcontroller (MCU) |
| Processor Core | Arm Cortex-M3 |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 512 kB |
| Data Memory | 96 kB |
| Architecture | 32-bit |
| Ethernet Support | Yes |
| USB Support | USB 2.0 device, host, and OTG |
| DMA Controller | 8 channels |
| UART Count | 5 |
| CAN Channel Count | 2 |
| SSP/SPI Interface Count | 3 |
| I2C Interface Count | 3 |
| I2S Support | Yes |
| ADC Resolution | 12-bit |
| ADC Channel Count | 8 |
| DAC Resolution | 10-bit |
| Quadrature Encoder Interface | Yes |
| SD/MMC Support | Yes |
| Motor Control Support | Yes |
| Volte ng Pagbibigay | 3.3 V |
| Package Type | 208-pin LQFP |
| Package Dimensions | 28 mm x 28 mm |
| Uri ng Pagpapasok | Surface mount |
| Automotive Qualification | AEC-Q100 |
Gabay sa Pin Configuration ng LPC1778FBD208K 28 mm x 28 mm
Pin configuration para sa LPC1778FBD208K (28 mm x 28 mm package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa LPC1778FBD208K.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LPC1778FBD208K ay nararapat para sa 6 aplikasyons: Industrial Ethernet Gateway, USB-to-Ethernet Control Hub, Factory Automation Controller, Motor Control and Positioning System, Data Acquisition and Monitoring Unit, USB Communications Adapter.
Industrial Ethernet Gateway
The LPC1778FBD208K fits an industrial Ethernet gateway because it combines a 120 MHz Arm Cortex-M3 core with integrated Ethernet, USB 2.0 device and OTG support, 512 kB of flash, and 96 kB of data memory. The 8-channel DMA controller can transfer network and serial data while the Cortex-M3 handles protocol processing, local control, and diagnostics. Five UARTs and three I2C interfaces allow the gateway to connect sensors, local displays, and service controllers without excessive discrete interfacing. Ethernet magnetics, proper termination, controlled-impedance routing, and careful separation between analog and high-speed digital sections remain essential.
Inirekomenda
USB-to-Ethernet Control Hub
The LPC1778FBD208K can serve as the central controller in a USB-to-Ethernet hub because USB 2.0 device, host, and OTG functions coexist with Ethernet and an 8-channel DMA controller. Its 120 MHz processing rate supports protocol handling and supervisory tasks, while 512 kB of flash accommodates firmware and 96 kB of data memory supports active buffers. The design should validate USB impedance, connector protection, Ethernet magnetics, ground continuity, and enumeration behavior. DMA allocation and buffer ownership must also be tested under sustained traffic to avoid overrun conditions.
Inirekomenda
Factory Automation Controller
The LPC1778FBD208K is suitable for factory automation because it combines 120 MHz Cortex-M3 processing with 5 UARTs, 2 CAN channels, 3 SSP/SPI interfaces, 3 I2C interfaces, an 8-channel 12-bit ADC, and a 10-bit DAC. This resource mix can supervise sensors, actuators, remote I/O, and service interfaces within one controller. The 208-pin LQFP exposes the large peripheral set without requiring an external interface multiplexer. Practical deployments should include isolated power and communication interfaces where required, surge protection for exposed wiring, watchdogs, and firmware checks that prevent unsafe outputs after a fault.
Inirekomenda
Motor Control and Positioning System
The LPC1778FBD208K supports motor-control and positioning systems through its 120 MHz control capability, QEI support, dedicated motor-control features, 8-channel 12-bit ADC, and 10-bit DAC. The ADC channels can monitor motor and system feedback, while the QEI interface assists with rotary position measurement. The 208-pin LQFP provides access to the required control and feedback signals. Designers must still account for gate-drive isolation, current sensing, protection timing, and analog conditioning; firmware should include defined shutdown states and verify safe outputs after reset or communication failure.
Inirekomenda
Data Acquisition and Monitoring Unit
The LPC1778FBD208K can act as a data-acquisition unit because its 8-channel 12-bit ADC operates alongside 96 kB of data memory, 512 kB of flash, 3 I2C channels, 3 SSP/SPI channels, and 5 UARTs. Analog measurements can be collected while serial and bus-connected sensors feed data into the 120 MHz Cortex-M3 core. The 10-bit DAC can support stimulus or control outputs where appropriate. Practical implementations should condition analog inputs, account for sampling and conversion time, isolate noisy power domains, and provide buffering so acquisition activity does not disrupt communication or control tasks.
Inirekomenda
USB Communications Adapter
The LPC1778FBD208K fits a USB communications adapter because it provides USB 2.0 device, host and OTG support alongside 5 UARTs, 3 SSP/SPI interfaces, 3 I2C interfaces, and 2 CAN channels. A single MCU can manage USB enumeration, protocol conversion, configuration, and diagnostic reporting at up to 120 MHz. The 8-channel DMA controller assists with moving data between USB and external interfaces, while 96 kB of data memory provides working space. Production validation should cover enumeration across host versions, hot-plug behavior, ESD protection, connector layout, and sustained data-transfer throughput.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LPC1778FBD208K — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LPC1778FBD208 |
|---|---|---|
| Package | 208-pin LQFP (28 mm x 28 mm) | 208-pin LQFP (28 mm x 28 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Processor Core | Arm Cortex-M3 | Arm Cortex-M3 |
| Maximum CPU Frequency | 120 MHz | 120 MHz |
| Flash Memory | 512 kB | 512 kB |
| Data Memory | 96 kB | 96 kB |
| Connectivity | Ethernet, USB 2.0 device/host/OTG, 2 CAN, 5 UART | Ethernet, USB 2.0 device/host/OTG, 2 CAN, 5 UART |
| Analog Conversion | 8-channel 12-bit ADC and 10-bit DAC | 8-channel 12-bit ADC and 10-bit DAC |
| Supply Voltage | 3.3 V | 3.3 V |
Pangunahing mga Pagkakaiba
- Exact same-package manufacturer ordering option (kumpara saLPC1778FBD208)
- High peripheral integration in a single MCU (kumpara saSTM32F429NIH6TR)
- Dedicated DMA support for connected embedded workloads (kumpara saLPC1759FBD80K)
Talaan ng Disenyo
The verified distributor listing identifies a 3.3 V supply for LPC1778FBD208K. Provide each supply domain with the decoupling and bulk capacitance required by the manufacturer datasheet, place high-frequency bypass capacitors adjacent to the relevant pins, and verify the complete 208-pin footprint against the official NXP package drawing before fabrication. Ethernet and USB interfaces should receive filtered, low-impedance supply paths where required. Do not infer capacitor values from generic MCU designs because the selected regulator, clocking scheme, and transceiver implementation determine the required energy and filtering.
The 208-pin LQFP footprint has a dense lead pitch and requires careful escape routing between the MCU and Ethernet, USB, CAN, ADC, DAC, and motor-control functions. Follow the official NXP land pattern and paste stencil rather than relying on a generic LQFP footprint. Sequence the layout to keep high-speed Ethernet and USB routes short and continuous, provide an uninterrupted ground reference, separate analog inputs from switching nodes, and reserve unobstructed access for inspection and rework.
Ethernet and USB are the most sensitive digital interfaces on this device because they combine many perimeter pins with high-speed routing requirements. Use controlled-impedance routing based on the actual board stack-up, maintain continuous reference planes, avoid stubs and unnecessary vias, and apply manufacturer-recommended termination. Place the Ethernet PHY and magnetics close to the relevant MCU pins where the reference design specifies it. Validate signal integrity and protocol compliance with eye diagrams or equivalent measurements rather than relying only on functional enumeration.
Do not substitute a broadly similar Cortex-M3 or Cortex-M4 device without checking every multiplexed peripheral and pin. The LPC1778FBD208K has 208 exposed pins and combines Ethernet, USB, two CAN channels, five UARTs, three SSP/SPI ports, three I2C ports, I2S, ADC, DAC, QEI, SD/MMC, and motor-control resources. Boot pins, power pins, debug functions, and peripheral multiplexing can differ even when CPU frequency and memory capacity are similar. Require a complete pin table, memory map comparison, and firmware porting plan before approving any substitution.
Impormasyon ng Pagsunod sa Kautusan
The Arrow distributor result identifies LPC1778FBD208K as automotive AEC-Q100. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly provided in the verified data. The automotive statement applies to the ordering code shown by that distributor listing.
