MAX3385EEAP - 250kbps RS-232 Transceiver | Analog Devices
MPN: MAX3385EEAP ✓ NakahandaMAX3385EEAP Ulas
An RS-232 transceiver is an interface IC that belongs to the line-driver and line-receiver hierarchy within interface semiconductors. It converts logic-level signals into RS-232-compatible levels in the transmit direction and converts incoming RS-232 levels back into logic levels in the receive direction. The MAX3385EEAP therefore provides the physical signaling layer between equipment logic and a cable-based serial interface.
Key characteristics include support for both 3.0V and 5.5V supply operation, a maximum signaling rate of 250kbps, low-power design, true RS-232 transceiver operation, and ±15kV ESD protection. The 3.0V minimum supply makes the interface suitable for systems whose digital core operates below 5V, while the 5.5V upper limit allows use with conventional 5V equipment. The 250kbps rate supports modern point-to-point serial links without requiring the lower bandwidth associated with legacy communication standards.
The MAX3385EEAP combines two transmit drivers and two receive receivers in one package, matching the conventional direction and signal arrangement used by RS-232 interface designs. Its integrated ESD protection reduces the amount of external protection normally required at a connector or cable entry. Applications still require correct signal routing, suitable bypass capacitance, controlled return paths, and compliance with the applicable RS-232 electrical requirements.
Typical uses include industrial control consoles, test equipment, data acquisition systems, service interfaces, and embedded products that retain an RS-232 port for configuration or diagnostics. The part is particularly useful where modern 3.3V logic must communicate with an RS-232 host while board area and external protection components must be minimized.
Designers should begin with the manufacturer's pin-description table when assigning PCB tracks and must preserve the documented charge-pump and driver topology around the transceiver. Input and supply bypassing should be placed close to the relevant pins, and connector-side protection must be reviewed against the required ESD exposure and working voltage.
This page consolidates the core electrical and package characteristics of the MAX3385EEAP with application guidance, comparison parameters, and practical interface-design considerations. It is intended to help engineers determine whether the device's voltage range, data rate, package, and protection level match a particular RS-232 design before committing the footprint to a PCB.
Mga alternatibo na pwedeng ilagay na MAX3385EEAP — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
MAX3385E
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MAX3385EEAP Mga Spesipikasyon
| Device Type | RS-232 transceiver |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps |
| ESD Protection | ±15kV |
| Power Class | Low-power |
| Interface Standard | RS-232 |
| Packhaging | 20-pin SSOP |
| Terminal Count | 20 |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| Uri ng Pagpapasok | Surface mount |
| Tindminan RoHS | Non-compliant |
| AEC-Q100 Qualification | Not applicable |
Gabay sa Pin Configuration ng MAX3385EEAP rectangular
Pin configuration para sa MAX3385EEAP (rectangular package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa MAX3385EEAP.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MAX3385EEAP ay nararapat para sa 6 aplikasyons: Industrial Control Consoles, Data Acquisition Equipment, Embedded Diagnostic Interfaces, Test and Measurement Instruments, Serial Printers and Point-of-Sale Equipment, Network Equipment Service Ports.
Industrial Control Consoles
The MAX3385EEAP fits industrial control consoles that need an RS-232 service port while using modern low-voltage logic. Its 3.0V to 5.5V supply range allows operation from a 3.3V control platform, while the 250kbps maximum data rate supports configuration downloads, diagnostic logs, and short command exchanges. The integrated ±15kV ESD protection adds useful robustness where the serial connector is exposed to routine handling and cable transients. Place the transceiver between the logic connector and protected RS-232 lines, observe the manufacturer's bypass-capacitor recommendations, and provide a controlled chassis or signal return to reduce common-mode noise.
Inirekomenda
Data Acquisition Equipment
The MAX3385EEAP is appropriate for laboratory and industrial data-acquisition equipment that retains an RS-232 configuration or calibration port. A 250kbps interface rate can transfer commands and compact status information efficiently, while the 3.0V minimum supply supports interface logic operating from 3.3V. The ±15kV ESD protection helps protect the transceiver when users connect external cables, although instrumentation designs may require additional attenuation, filtering, or surge protection. Keep the RS-232 traces short where practical, route the logic-side signals away from analog inputs, and use the manufacturer's pin-description table to implement the power, ground, and charge-pump connections correctly.
Inirekomenda
Embedded Diagnostic Interfaces
The MAX3385EEAP can provide a dedicated diagnostic channel for embedded controllers, industrial appliances, and field-service equipment. Its low-power 3.3V-compatible operating range leaves more of the supply budget for logic and processing, while the 20-pin SSOP package supports compact board layouts. At up to 250kbps, the link is suitable for boot logs, status messages, configuration commands, and firmware update initiation. The interface should be enabled only when required if system power management prioritizes standby consumption. Keep the serial connector away from high-current switching paths and use a solid return connection to the logic ground according to the system grounding strategy.
Inirekomenda
Test and Measurement Instruments
The MAX3385EEAP is suitable for test and measurement instruments that communicate with legacy computers, printers, or automated test systems through RS-232. The 3.0V to 5.5V supply range supports both modern instrument control logic and older 5V interface sections, and the 250kbps rate is useful for command traffic and measurement data where latency remains acceptable. Integrated ±15kV ESD protection improves resilience to user-connected cables. During instrument design, separate the transceiver from sensitive analog or RF sections, maintain the recommended bypass capacitance at the device, and evaluate additional attenuation or protection for long cables or electrically noisy environments.
Inirekomenda
Serial Printers and Point-of-Sale Equipment
The MAX3385EEAP can bridge a low-voltage embedded controller to an RS-232 receipt printer or point-of-sale peripheral. Its 250kbps capability exceeds the requirements of many transactional printer links and provides margin for command acknowledgment traffic. The device operates from a 3.0V to 5.5V supply, which is useful in compact systems based on 3.3V logic, while ±15kV ESD protection supports connection to an external cable. Route the driver outputs and receiver inputs away from switching regulators and noisy relay nodes. Confirm cable length, grounding, and the peripheral's logic levels before production use because RS-232 voltage levels are not directly interchangeable with CMOS levels.
Inirekomenda
Network Equipment Service Ports
The MAX3385EEAP is suitable for a service or management port on network appliances where an RS-232 connector remains available for installation and maintenance. The 3.3V-compatible supply range helps integrate the interface with modern network-controller platforms, and the 250kbps rate is sufficient for console sessions and configuration transfer. The ±15kV ESD rating is particularly relevant to equipment that may be connected during installation or service. Place the interface near the connector, maintain separation from Ethernet magnetics and high-speed switching nodes, and use controlled grounding. If the equipment requires galvanic isolation or remote cable exposure beyond the connector boundary, add the appropriate isolation and surge-protection network.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MAX3385EEAP — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MAX3385E |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 20-pin SSOP | 20-pin SSOP |
| Device Type | RS-232 transceiver | RS-232 transceiver |
Pangunahing mga Pagkakaiba
- Supports 3.3V system logic directly (kumpara saMAX3385E)
- Supports a 250kbps RS-232 data rate (kumpara saMAX3385E)
- Integrates ±15kV ESD protection (kumpara saMAX3385E)
- Uses a compact 20-pin SSOP footprint (kumpara saMAX3385E)
Talaan ng Disenyo
Route the RS-232 driver and receiver nets directly to their assigned connector or protection-network locations, and keep those paths away from switching nodes and high-current relay traces. Use the manufacturer's pin-description table to assign all 20 SSOP terminals, including supply, ground, receiver outputs, driver inputs, and any charge-pump or enable-related connections. Place input and bypass capacitors close to their specified pins with short ground returns.
RS-232 signaling can be affected by common-mode voltage on long or unshielded cables. Establish a predictable return path between the two connected systems, avoid floating signal references, and keep the cable interface away from sources of large transient currents. The MAX3385EEAP provides ±15kV ESD protection, but that rating does not replace a surge-protection network when the cable will encounter sustained overvoltage or severe lightning exposure.
Do not treat the 250kbps rating as a guarantee of long-distance communication. RS-232 cable length, baud rate, capacitance, ground reference, driver loading, and receiver thresholds all affect the usable link. Also confirm that the connected equipment uses ±RS-232 signaling rather than RS-485, RS-422, or logic-level serial signals, because those interfaces are not electrically interchangeable even when their connector pinouts appear similar.
Check the transceiver's supply current and line-loading behavior against the power budget for every supported operating state. Although the MAX3385EEAP is identified as a low-power device operating from 3.0V to 5.5V, the exact supply current is not listed here and should be taken from the manufacturer datasheet. Apply the recommended supply decoupling and avoid placing the interface's switching activity on an unprotected sensitive analog rail.
Impormasyon ng Pagsunod sa Kautusan
The product listing explicitly identifies the MAX3385EEAP as RoHS non-compliant. No manufacturer statement for REACH, lead-free status, halogen-free status, or conflict-minerals compliance was identified.
