MC74F569N - 4-Bit Bidirectional Counter | onsemi | Logic
MPN: MC74F569N ✗ Tapus ng BuhayMC74F569N Ulas
A bidirectional counter is a synchronous digital sequential circuit that counts either upward or downward from a loaded preset value. Unlike a simple unidirectional ripple counter, this type of counter can track positive and negative counting sequences from the same logic state. The 3-state output architecture belongs to the broader bus-interface hierarchy: logic IC > counter > binary counter > bus-compatible digital component. Tri-state outputs permit multiple devices to share a common data bus without creating contention when a device is disabled.
The MC74F569N is identified as a counter IC with a 4-bit element. Its principal functional characteristics include bidirectional counting, preset capability for programmable operation, and carry-look-ahead functions intended to simplify cascading, as described for the related 74F569 family. Three-state outputs add bus-interface flexibility, allowing an external controller to select which counter drives the shared data path. These characteristics are more important for system timing and control than the numeric operating frequency alone.
The 74F569 family architecture is based on edge-triggered logic behavior intended for synchronous counter operation. A synchronous design allows the counter state to advance in response to a common clock edge, simplifying multi-stage count chains because the stages do not rely on ripple propagation. Preset inputs establish an initial count, while direction control determines whether subsequent clock edges increment or decrement that count. Carry logic provides a way to detect and extend counting ranges beyond four bits.
Typical uses include digital chronometers, industrial sequence controllers, frequency-divider and event-counting circuits, programmable timing modules, and address-generation blocks. In each case, the counter can be loaded with a starting value, advanced or reversed under direction control, and connected to shared bus lines through its 3-state outputs. Care is required when multiple counters share a bus because exactly one enabled device should drive the bus at any given time.
For PCB implementation, use the manufacturer pin-description table to assign every signal and preserve the original package footprint, power connections, and decoupling arrangement. A common 0.1 uF ceramic bypass capacitor should be placed close to the power and ground pins when the device is used in conventional digital logic designs. Clock, count-enable, preset, and direction traces should be kept away from output and bus traces where switching activity could cause unintended transitions.
This product record combines the MC74F569N identity, 4-bit bidirectional-counter function, 3-state-output feature, sourcing links, package constraints, and replacement guidance into a design-oriented reference. Because complete electrical ratings and pin assignments are not reproduced in the manufacturer document excerpts, use the MC74F569N datasheet for final logic-level, timing, package, and footprint decisions before placing an order.
Mga alternatibo na pwedeng ilagay na MC74F569N — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboMC74F569N Mga Pinakamataas na Rating at Electrical Characteristics
| Counter Type | Synchronous binary counter |
| Counter Width | 4 bits |
| Count Direction | Bidirectional, up/down |
| Output State | 3-state output |
| High-Impedance Output State | Enabled for bus sharing |
| Preset Capability | Programmable initial count |
| Carry Function | Carry-look-ahead |
| Logic Family | 74F fast logic |
| Tindminan RoHS | Compliant |
Gabay sa Pin Configuration ng MC74F569N standard
Pin configuration para sa MC74F569N (standard package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa MC74F569N.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MC74F569N ay nararapat para sa 6 aplikasyons: Programmable Event Counter, Digital Timing and Elapsed-Time Module, Industrial Sequence Controller, Frequency Divider and Cascaded Count Chain, Digital Address Generation, Data Acquisition and Sample Indexing.
Programmable Event Counter
The MC74F569N fits bidirectional event counting because it provides a 4-bit counting element, preset capability, and selectable count direction. A controller can load a starting value, enable counting on qualified events, and later read the result through the counter outputs. Direction control also permits the same hardware to support both increasing and decreasing event sequences. The 3-state outputs simplify connection to a shared bus where several counters must be read selectively, provided only one device is enabled at a time.
Inirekomenda
Digital Timing and Elapsed-Time Module
The MC74F569N can represent elapsed time or remaining time as a 4-bit binary count when the system converts a stable time-base signal into clock events. Preset inputs establish the initial count, while up/down control determines whether the value progresses toward a higher or lower endpoint. The 74F569 family description identifies synchronous operation, carry look-ahead, and programmable operation as central functions, helping designers create cascaded timing ranges without relying on asynchronous ripple increments.
Inirekomenda
Industrial Sequence Controller
A 4-bit up/down counter is useful in industrial sequence control because it can track discrete process steps and respond to forward or reverse commands. The MC74F569N can be preset at a defined step and advanced as the controller recognizes completed operations. Its carry indication supports extension to wider sequence ranges, while the tri-state outputs allow the count to be observed by a common controller bus. Firmware must ensure that bus ownership is mutually exclusive and that preset changes occur only in valid clock intervals.
Inirekomenda
Frequency Divider and Cascaded Count Chain
The MC74F569N is suitable for frequency division and multi-stage count chains because a binary counter divides an input clock by powers of two and produces a carry indication when its four-bit count reaches its terminal state. The family’s carry-look-ahead function assists programmable operation and cascading. Designers can combine multiple counting stages, use preset values to establish phase offsets, and route the tri-state outputs into shared buses when several divider stages need selective access.
Inirekomenda
Digital Address Generation
The MC74F569N can form part of a programmable address-generation block because it stores a 4-bit binary value and can increment or decrement that value under control logic. Preset inputs allow new address segments to begin at a defined boundary, while carry output indicates when a segment limit has been reached. The 3-state outputs are useful in bus-based architectures where address fragments are exposed to a shared bus only during the required access interval, reducing contention between multiple counters.
Inirekomenda
Data Acquisition and Sample Indexing
The MC74F569N can maintain a sample index, repeat count, or channel-selection value in a digital acquisition system. A four-bit element offers sixteen count states, and preset capability allows each acquisition burst to begin at a known index. Direction control supports counting forward for successive samples or backward for reverse scans. Because the outputs are 3-state, several counter sections may share parallel buses, but the controlling logic must guarantee non-overlapping output-enable periods and comply with the device’s setup and hold timing.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MC74F569N — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | onsemi |
| Counter Width | 4 bits |
| Count Direction | Bidirectional up/down |
| Output Type | 3-state output |
| Preset Capability | Programmable preset operation |
| Carry Function | Carry-look-ahead |
| Logic Family | 74F fast logic |
Pangunahing mga Pagkakaiba
- Bidirectional counting in a compact 4-bit element (kumpara sa74F569)
- Tri-state outputs support shared-bus architectures (kumpara sa74F569)
- Programmable operation with carry look-ahead (kumpara sa74F569)
Talaan ng Disenyo
Do not assume that a 74F-family functional equivalent is automatically a drop-in replacement. Confirm the exact pinout, package dimensions, lead orientation, supply range, output timing, preset behavior, and output-enable polarity against the MC74F569N datasheet. A suffix such as N can identify a specific package or temperature option, and changing that suffix without verifying the mechanical drawing can prevent assembly, alter pin mapping, or introduce an electrical mismatch.
Treat clock, preset, and direction inputs as synchronous signals and preserve their required setup and hold relationships. Route the clock away from parallel output buses and shared-enable traces to reduce crosstalk and false state transitions. If multiple counters drive one bus, use one decoded output-enable signal per device and guarantee non-overlap; two enabled outputs with different data values can create excessive contention current.
Place the device power bypass capacitor close to its supply and ground pins, following the value and layout recommendations in the manufacturer datasheet. Maintain short, direct paths for clock and control inputs, and provide adequate ground-plane continuity beneath the package. Because the exact physical package is not identified in the accessible technical summary, reproduce the original PCB footprint from the verified package drawing rather than inferring it from the MPN suffix.
Impormasyon ng Pagsunod sa Kautusan
The LCSC product document identifies the MC74F569N as RoHS compliant. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was present in the accessible product information.