MCP6009-E/SL - 4-Channel 1MHz RRIO Op Amp | Microchip
MPN: MCP6009-E/SL ✓ NakahandaMCP6009-E/SL Ulas
An operational amplifier, commonly called an op amp, is an active semiconductor that amplifies the difference between two input voltages. In the broader hierarchy, an op amp belongs to the amplifier IC category and the analog signal-processing family. Rail-to-rail input operation permits the input common-mode range to approach the supply rails, while rail-to-rail output operation allows the output voltage to swing close to those limits under suitable load conditions.
The MCP6009-E/SL combines four amplifiers in one package. According to the manufacturer datasheet, its typical gain-bandwidth product is 1 MHz, maximum input offset voltage is 1.6 mV, and typical input bias current is 1 pA. Maximum quiescent current is 70 µA per amplifier, while the listed input noise density is 25 nV/√Hz at 1 kHz. The device is unity-gain stable and supports a slew rate of 3 V/µs.
Its low-voltage operation is suitable for battery-powered and energy-conscious equipment. The input stage includes capacitive filtering for EMI suppression, reducing sensitivity to interference coupled onto sensitive sensor or measurement lines. Four channels in one SOIC-14 package can also reduce board area when a design needs multiple buffers, amplifiers, or active filters. The family is intended for general-purpose analog signal conditioning rather than precision instrumentation amplification.
Typical uses include low-voltage sensor conditioning, portable measurement equipment, audio preamplification, battery monitoring, and general-purpose signal buffering. The MCP6009-E/SL is particularly useful where several low-power channels must operate from the same supply while accepting input signals near either supply rail. Its 1 MHz bandwidth is adequate for low-frequency control, sensing, and audio tasks rather than high-speed video or communications.
When designing around the MCP6009-E/SL, keep each input and output connection short, provide a stable supply reference, and avoid capacitive loading on the output. Decoupling capacitors should connect directly between the supply and ground pins near the device. Verify the external feedback network, output load, and input common-mode range across temperature before using the amplifier at the extremes of its 1.8 V to 5.5 V operating range.
This product page organizes the amplifier's electrical limits, package information, drop-in alternatives, application guidance, and design considerations into a single engineering reference. It highlights where the 1 MHz bandwidth, low quiescent current, rail-to-rail operation, and EMI filtering make the MCP6009-E/SL useful, while also separating it from options that offer higher speed or different channel counts.
Mga alternatibo na pwedeng ilagay na MCP6009-E/SL — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
MCP6009-I/SL
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MCP6004-E/SL
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MCP6009-E/SL Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Channels | 4 amplifiers |
| Gain-Bandwidth Product | 1 MHz typical |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Input Offset Voltage | ±1.6 mV maximum |
| Input Bias Current | 1 pA |
| Input Noise Density | 25 nV/√Hz at 1 kHz |
| Kuru-kuryente ng Kapayapaan | 70 µA maximum per amplifier |
| Slew Rate | 3 V/µs |
| Offset Voltage Drift | 600 nV/°C |
| EMI Filtering and RF Suppression | 90 dB |
| Common-Mode Input | Rail-to-rail |
| Common-Mode Output | Rail-to-rail |
| Gain Stability | Unity-gain stable |
| Hanay ng Temperature na Operasyon | -40°C to +125°C |
| Packhaging | 14-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Tindminan RoHS | Compliant |
Pin Configuration ng MCP6009-E/SL
| Pin 1 | OUTA — Channel A output |
| Pin 2 | IN A- — Channel A inverting input |
| Pin 3 | IN A+ — Channel A non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | IN B+ — Channel B non-inverting input |
| Pin 6 | IN B- — Channel B inverting input |
| Pin 7 | OUTB — Channel B output |
| Pin 8 | OUTC — Channel C output |
| Pin 9 | IN C- — Channel C inverting input |
| Pin 10 | IN C+ — Channel C non-inverting input |
| Pin 11 | V+ — Positive supply connection |
| Pin 12 | IN D+ — Channel D non-inverting input |
| Pin 13 | IN D- — Channel D inverting input |
| Pin 14 | OUTD — Channel D output |
Tipikal na mga Gamit
MCP6009-E/SL ay nararapat para sa 6 aplikasyons: Low-Voltage Sensor Signal Conditioning, Battery-Powered Portable Instruments, Audio Preamplification and Buffering, Industrial Control Signal Conditioning, Battery Monitoring and Protection, General-Purpose Buffering and Active Filtering.
Low-Voltage Sensor Signal Conditioning
The MCP6009-E/SL fits four-channel sensor conditioning when signals must be amplified close to the supply rails. Its 1.8 V to 5.5 V operating range supports low-energy systems, while rail-to-rail inputs prevent clipping when a sensor output approaches either supply limit. The 1 MHz typical gain-bandwidth product supports low-frequency resistive sensors, while maximum input offset voltage of ±1.6 mV determines the smallest useful gain for accuracy-critical measurements. The 90 dB EMI filtering can reduce interference coupled through long sensor wiring, although the application should still include appropriate input protection and grounding.
Inirekomenda
Battery-Powered Portable Instruments
The MCP6009-E/SL supports portable instruments that need several analog channels while keeping energy use modest. The family rating of 70 µA maximum quiescent current per amplifier is important when the instrument operates continuously from a small battery, and the 1.8 V minimum supply permits direct operation from low-energy rails. Four unity-gain-stable amplifiers can perform buffering, gain, filtering, or reference-interface functions without requiring separate devices for every channel. Designers should calculate the complete load current, regulator dropout, and sleep-mode behavior rather than relying only on quiescent current.
Inirekomenda
Audio Preamplification and Buffering
The MCP6009-E/SL is suitable for low-frequency audio preamplifier and buffer stages that do not require wideband video performance. Its 3 V/µs slew rate and 1 MHz typical gain-bandwidth product provide useful margin for audio-band gain stages, while rail-to-rail output operation increases available swing at low supply voltages. Four channels allow stereo construction with additional monitoring or control paths. The 25 nV/√Hz input noise density at 1 kHz can contribute to low-level audio noise, so resistor selection, source impedance, and supply decoupling remain important even though the device includes EMI filtering.
Inirekomenda
Industrial Control Signal Conditioning
The MCP6009-E/SL is appropriate for low-speed industrial control boards that condition 0–5 V, current-sensor, or resistive-divider signals using a low-voltage supply. Its rail-to-rail input and output behavior gives more usable signal range than a fixed common-mode amplifier, while four channels support actuator feedback, sensor inputs, and monitor signals in a single 14-pin SOIC. The -40°C to +125°C operating range supports demanding industrial environments, but system designers must also address surge, reverse-polarity, and ESD protection because those requirements are separate from the amplifier’s internal EMI filter.
Inirekomenda
Battery Monitoring and Protection
The MCP6009-E/SL can condition battery-cell, charger, and current-sense voltages in a compact protection circuit. Its 1.8 V minimum supply suits low-voltage energy systems, and rail-to-rail inputs are valuable when monitoring approaches the positive supply rail. The four channels can amplify a cell divider, charger-status signal, temperature sensor, and current-sensor output through a common package. Maximum input offset voltage of ±1.6 mV influences the smallest resolvable battery voltage after gain, while the low quiescent current helps preserve standby energy. Protection switches and high-current paths require separate components.
Inirekomenda
General-Purpose Buffering and Active Filtering
The MCP6009-E/SL fits multiplexed test points, ADC drivers, active filters, and general-purpose buffering because each channel is unity-gain stable. A 1 MHz typical gain-bandwidth product allows useful closed-loop bandwidth at moderate gains, while four independent channels reduce package count in a 14-pin SOIC design. The device can buffer high-impedance sources, but its 1 pA typical input bias current should be checked against source impedance and leakage requirements. Decoupling, grounding, and feedback-network layout determine whether the available bandwidth and EMI rejection translate into usable system performance.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MCP6009-E/SL — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MCP6009-I/SL | MCP6004-E/SL |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Number of Channels | 4 amplifiers | 4 amplifiers | 4 amplifiers |
Pangunahing mga Pagkakaiba
- Four-channel integration in a standard 14-pin SOIC (kumpara saMCP6007-E/SL)
- Explicit 90 dB EMI filtering and RF suppression (kumpara saMCP6004-E/SL)
- Low-voltage operation with rail-to-rail inputs and outputs (kumpara saMCP6009-I/SL)
Talaan ng Disenyo
Place the supply bypass capacitor directly between pins 11 and 4, with a short ground return and minimal loop area. Connect each amplifier’s feedback components close to the relevant input and output pins. The input EMI filter can reduce coupled noise, but long PCB traces still act as antennas; keep sensor and feedback routes compact, use a continuous ground reference, and avoid routing sensitive inputs beside switching-regulator power paths.
Check the complete power budget rather than using quiescent current alone. Estimated current per amplifier is the maximum of 70 µA quiescent current and the output-current demand, multiplied by four channels, plus bias and feedback-network current. For example, four channels at the 70 µA quiescent limit contribute 280 µA before external loading. Confirm that the supply remains above 1.8 V and above the input and output signal requirements throughout startup, load transients, and battery discharge.
Do not treat the internal EMI filter as a substitute for input protection. Add the required series resistance or external clamp components when a sensor line can exceed the amplifier input limits. Also account for input offset voltage when setting the first gain stage: at unity gain, ±1.6 mV maximum offset can appear directly at the output. Feedback resistors with suitable tolerance and temperature coefficient should be used when the output accuracy requirement is tighter than that offset.
The SOIC-14 package is suitable for normal low-voltage operation, but power dissipation and junction temperature still depend on the supply voltage, load current, ambient temperature, and board copper. Estimated dissipation is approximately the product of the amplifier output-current demand and the output-to-supply voltage difference. Maintain copper around the package, avoid enclosing the device in a sealed enclosure without thermal analysis, and account for temperature drift of 600 nV/°C when precision offset performance matters.
Impormasyon ng Pagsunod sa Kautusan
RoHS compliance is stated for the MCP6009-E/SL. No automotive qualification, REACH declaration, halogen-free designation, or conflict-minerals statement was identified for this orderable MPN.