PIC16LF1719-I/PT - 28KB Flash 8-bit MCU, 32MHz, 44-TQFP
MPN: PIC16LF1719-I/PT ✓ NakahandaPIC16LF1719-I/PT Ulas
An 8-bit microcontroller is a single-chip computer built around an 8-bit data path, on-chip Flash for program storage, on-chip RAM for data, and a rich set of mixed-signal peripherals. PIC microcontrollers use a RISC instruction set and Harvard architecture, meaning the program and data buses are physically separated to allow simultaneous fetch and operand access. Within the broader component taxonomy, PIC MCUs belong to microcontrollers -> microcontrollers and microprocessors -> integrated circuits -> semiconductors. They occupy the same functional layer as AVR, STM8 and low-end Cortex-M0 parts but trade raw 32-bit throughput for deterministic interrupt latency, ultra-low sleep current, and a stable long-life toolchain. The PIC16LF1719 specifically sits in the "intelligent-analog" sub-family, integrating op-amps, 5/8-bit DACs, 10-bit ADC, comparators, COG, NCO, ZCD, CLC, and PPS signal routing on-chip, so most glue logic that would otherwise surround a small analog MCU can be absorbed into the silicon.
Key differentiating features include four op-amps (with selectable internal/external routing), two 5-bit DACs and one 8-bit DAC, a 10-bit ADC with up to 28 channels, two comparators, and four 16-bit PWM/CCP timers. The PPS (Peripheral Pin Select) matrix lets designers remap most I/O functions to any digital pin, simplifying PCB layout for mixed-signal designs. A separate Low-Power Brown-out Reset (LPBOR) and Windowed Watchdog Timer improve system robustness in noisy industrial environments.
The architecture uses a single-cycle ALU with a 32 MHz internal oscillator, two hardware stack levels of interrupt priority, and a 14-bit instruction word. The integrated 32 MHz HFINTOSC is factory calibrated to within ±1 % across voltage and temperature, which lets many designs eliminate an external crystal and reduce BOM cost. XLP (eXtreme Low Power) technology brings the typical sleep current below 50 nA with the RTC active, a key reason this part is favored in battery-powered sensors.
Typical applications include battery-powered IoT sensor nodes, low-power wireless transmitters, white-goods and HVAC user-interface panels, handheld industrial instruments, LED lighting controllers with analog dimming, and small mixed-signal front-ends where the on-chip op-amps and DACs replace external analog ICs. In each scenario the wide-voltage core, XLP sleep current and integrated intelligent analog peripherals directly shorten design time and reduce board area.
When designing with this device, keep the analog supply (AVDD) well bypassed and lay out the analog ground as a star or split plane that returns to the device EP, since the on-chip ADC accuracy depends heavily on clean ground. Always enable the Fail-Safe Clock Monitor (FSCM) when the system clock is derived from an external crystal, and reserve a free PPS channel for in-system debug via the ICSP pins (PGC/PGD) to avoid locking the MCU during board bring-up.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, giving procurement and design engineers a single reference for evaluating the PIC16LF1719-I/PT against modern low-power MCU requirements.
Mga alternatibo na pwedeng ilagay na PIC16LF1719-I/PT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok PIC16LF1719-I/PT (parehas na form factor at footprint) — pagkakaiba sa ADC, Program Memory (Flash), Package, Core Architecture, Core Independent Peripherals.
PIC16F1719-I/PT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PIC16LF1718-I/PT
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
PIC16LF1717-I/PT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PIC16LF1719-I/PT Mga Pinakamataas na Rating at Electrical Characteristics
| Core Architecture | 8-bit PIC RISC (Harvard) |
| Family | PIC® XLP™ 16F |
| Maximum CPU Frequency | 32 MHz |
| Program Memory (Flash) | 28 KB (16K x 14 words) |
| Data SRAM | 2 KB |
| Data EEPROM | 256 bytes |
| Operating Voltage Range | 1.8 V to 3.6 V |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C (Industrial) |
| ADC | 10-bit, up to 28 channels |
| DAC | Two 5-bit + one 8-bit |
| Op-Amps | 4 on-chip |
| Comparators | 2 |
| Timers | 4x 16-bit (PWM/CCP) |
| Communication | EUSART, I2C, SPI |
| Packhaging | 44-pin TQFP (10x10 mm) |
| Uri ng Pagpapasok | Surface Mount |
| Level ng MSL | MSL3 (per JEDEC J-STD-020) |
| Tindminan RoHS | Compliant |
| Lead-Free | Yes |
Pin Configuration ng PIC16LF1719-I/PT
| Pin 1 | RA5 — Port A bit 5 / ICSPDAT |
| Pin 2 | RA4 — Port A bit 4 |
| Pin 3 | RA3 — Port A bit 3 / MCLR (weak pull-up) |
| Pin 4 | RA2 — Port A bit 2 |
| Pin 5 | RA1 — Port A bit 1 |
| Pin 6 | RA0 — Port A bit 0 |
| Pin 7 | VSS — Digital ground |
| Pin 8 | RA7 — Port A bit 7 / OSC1 |
| Pin 9 | RA6 — Port A bit 6 / OSC2 |
| Pin 10 | RC0 — Port C bit 0 |
| Pin 11 | VDD — Digital supply (1.8–3.6 V) |
| Pin 12 | AVDD — Analog supply |
| Pin 13 | AVSS — Analog ground |
| Pin 14 | RC1 — Port C bit 1 |
| Pin 15 | RC2 — Port C bit 2 |
| Pin 16 | RC3 — Port C bit 3 / SCL |
| Pin 17 | RC4 — Port C bit 4 / SDA |
| Pin 18 | RC5 — Port C bit 5 |
| Pin 19 | RC6 — Port C bit 6 / TX |
| Pin 20 | RC7 — Port C bit 7 / RX |
| Pin 21 | RB0 — Port B bit 0 / INT |
| Pin 22 | RB1 — Port B bit 1 |
| Pin 23 | RB2 — Port B bit 2 |
| Pin 24 | RB3 — Port B bit 3 |
| Pin 25 | RB4 — Port B bit 4 |
| Pin 26 | RB5 — Port B bit 5 |
| Pin 27 | RB6 — Port B bit 6 / ICSPCLK |
| Pin 28 | RB7 — Port B bit 7 |
| Pin 29 | VSS — Digital ground |
| Pin 30 | VDD — Digital supply |
| Pin 31 | RE3 — Port E bit 3 |
| Pin 32 | RD0 — Port D bit 0 |
| Pin 33 | RD1 — Port D bit 1 |
| Pin 34 | RD2 — Port D bit 2 |
| Pin 35 | RD3 — Port D bit 3 |
| Pin 36 | RD4 — Port D bit 4 |
| Pin 37 | RD5 — Port D bit 5 |
| Pin 38 | RD6 — Port D bit 6 |
| Pin 39 | RD7 — Port D bit 7 |
| Pin 40 | VSS — Digital ground |
| Pin 41 | VDD — Digital supply |
| Pin 42 | RE0 — Port E bit 0 |
| Pin 43 | RE1 — Port E bit 1 |
| Pin 44 | RE2 — Port E bit 2 |
Tipikal na mga Gamit
PIC16LF1719-I/PT ay nararapat para sa 6 aplikasyons: Battery-Powered IoT Sensor Nodes, Handheld Industrial Instruments, White-Goods and HVAC User-Interface Panels, LED Lighting Controllers with Analog Dimming, Low-Power Wireless Sensor Transmitters, Small Mixed-Signal Front-End Modules.
Battery-Powered IoT Sensor Nodes
The PIC16LF1719-I/PT's 1.8–3.6 V core, 50 nA XLP sleep current and integrated 10-bit ADC with up to 28 channels make it a strong fit for battery-powered IoT sensor nodes. Placed as the central MCU on a 3.3 V coin-cell or 2xAA rail, it wakes periodically, samples one or more analog sensors, and returns to deep sleep without an external LDO. The 28 KB Flash comfortably accommodates BLE/Zigbee stack stubs plus application logic, while the on-chip op-amps condition bridge sensors directly, eliminating front-end analog ICs.
Inirekomenda
Handheld Industrial Instruments
For handheld industrial instruments including multimeters, clamp meters, and process calibrators, the PIC16LF1719-I/PT combines 32 MHz performance, four on-chip op-amps, two comparators, and a 5/8-bit DAC set that drive LCD bias and reference trim. Operating from -40 °C to +85 °C industrial grade, it survives factory-floor thermal stress and ESD events better than consumer-grade MCUs. The 44-TQFP gives enough I/O for keypad scanning, segmented LCD driving, and isolated communication ports in a single chip.
Inirekomenda
White-Goods and HVAC User-Interface Panels
In white-goods and HVAC user-interface panels, the PIC16LF1719-I/PT drives capacitive touch keys, LED dimming channels, and a character or segment LCD from a single 3.3 V rail. The PPS matrix lets the PCB designer place keypad traces anywhere on the board without rewiring firmware, accelerating mechanical iteration. Integrated op-amps sense NTC temperature directly, while the 8-bit DAC provides smooth analog fan-speed or damper reference control without external DACs.
Inirekomenda
LED Lighting Controllers with Analog Dimming
The PIC16LF1719-I/PT powers constant-current LED drivers that require analog dimming down to 1 % without visible flicker. Its PWM/CCP timers generate high-resolution dimming waveforms while the 10-bit ADC monitors LED current and board temperature. The 1.8–3.6 V core also lets the MCU run directly from a single-cell lithium supply, removing the need for an intermediate boost stage in some architectural-lighting designs. XLP sleep keeps standby power below regulatory limits.
Inirekomenda
Low-Power Wireless Sensor Transmitters
For sub-1 GHz or 2.4 GHz proprietary wireless sensor transmitters, the PIC16LF1719-I/PT serves as the host MCU that wakes the radio, reads the sensor through the on-chip ADC, transmits a packet, and returns to deep sleep in a few hundred microseconds. Its 32 MHz MIPS throughput supports lightweight protocol stacks and AES-128 encryption in firmware, while the 256-byte EEPROM stores calibration and pairing data non-volatilely across battery swaps.
Inirekomenda
Small Mixed-Signal Front-End Modules
In small mixed-signal front-end modules such as RTD-to-digital conditioners, isolated 4–20 mA loop interfaces, or strain-gauge amplifiers, the PIC16LF1719-I/PT replaces a separate op-amp IC, ADC IC, and DAC trim IC with one MCU. Four on-chip op-amps form the bridge excitation and instrumentation stages, the 10-bit ADC digitizes the result, and the 8-bit DAC provides offset correction. This consolidation typically reduces BOM cost by 30–50 % and shrinks PCB area in space-constrained modules.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PIC16LF1719-I/PT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | PIC16F1719-I/PT | PIC16LF1718-I/PT | PIC16LF1717-I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (10x10) | 44-TQFP (10x10) | 44-TQFP (10x10) | 44-TQFP (10x10) |
| Operating Voltage | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Flash Memory | 28 KB | 28 KB | 14 KB | 14 KB |
| SRAM | 2 KB | 2 KB | 1 KB | 1 KB |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| On-Chip Op-Amps | 4 | 4 | 2 | 2 |
| DAC Resolution | 8-bit + 2x 5-bit | 8-bit + 2x 5-bit | 8-bit + 2x 5-bit | 8-bit + 2x 5-bit |
| ADC Resolution | 10-bit | 10-bit | 10-bit | 10-bit |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Pangunahing mga Pagkakaiba
- Highest Flash density in the PIC16LF171x 44-TQFP family (kumpara saPIC16LF1718-I/PT)
- Four on-chip op-amps versus two on smaller siblings (kumpara saPIC16LF1718-I/PT)
- Wide voltage range down to 1.8 V for battery designs (kumpara saPIC16F1719-I/PT)
Talaan ng Disenyo
The PIC16LF1719-I/PT operates from a single 1.8–3.6 V rail; place a 100 nF decoupling capacitor within 5 mm of each VDD/AVDD pin pair and a bulk 4.7 µF ceramic on the main VDD node. For battery applications, enable the LFINTOSC and disable the ADC during sleep to reach the XLP sleep current floor of 50 nA quoted in the Microchip datasheet. Avoid placing the MCU on a high-impedance rail that droops below 1.8 V under load, or the Brown-Out Reset will fire and reset the device unexpectedly.
Use a star-ground topology that returns analog ground (AVSS) and digital ground (VSS) to a single point near the MCU's EP. Keep high-speed digital traces (EUSART, SPI, PWM) at least 5 mm away from the analog input pins to preserve the 10-bit ADC SNR. Place the ICSP header (PGC/PGD on RB6/RA0) at the board edge so that production programming does not require cable extension.
Do not assume the on-chip op-amps can drive heavy loads; they are designed for sensor conditioning with output currents below a few mA. Do not leave the MCLR pin floating - tie it to VDD through a 10 kΩ resistor to prevent spurious resets. Always invoke the PPS unlock sequence (PPSLOCKED bit) before remapping peripherals, or the configuration will silently be ignored on the next reset.
Impormasyon ng Pagsunod sa Kautusan
RoHS and REACH compliance confirmed in Microchip product declaration. Industrial temperature grade (-40 °C to +85 °C) only; AEC-Q100 automotive parts require the -E/VAO suffix. Halogen-free status not stated in verified data.