PIC18F86K90-I/PTRSL - 8-bit 64MHz 64KB Flash MCU | Microchip
MPN: PIC18F86K90-I/PTRSL ✓ NakahandaPIC18F86K90-I/PTRSL Ulas
A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripheral IP such as timers, ADC, communications controllers, and I/O. Within the broader taxonomy, the PIC18F86K90 belongs to the 8-bit MCU family -> PIC18 sub-family -> PIC18FxxK90 LCD-driver family -> PIC18F8xK90 80-pin members. It targets battery-powered LCD applications that combine touch sensing, segmented display driving, and ultra-low standby current in the same silicon.
Key features include nanoWatt XLP™ technology for deep-sleep currents measured in nanoamps, an integrated LCD driver supporting up to 192 segments, a Charge Time Measurement Unit (CTMU) that enables capacitive touch and simple temperature measurement, 24 channels of 12-bit ADC, multiple UART/SPI/I²C interfaces, and an operating voltage range of 1.8V to 5.5V. The 'I' temperature grade denotes an industrial -40°C to +85°C operating range, and 'PTRSL' indicates the 80-pin TQFP (PT) package shipped in tape-and-reel (TR) orientation with SL suffix marking.
Architecturally, the device uses an enhanced Harvard RISC core with a hardware multiplier, 31-level stack, and a C-friendly instruction set, allowing efficient C compilation through Microchip's MPLAB XC8 toolchain. The 80-pin TQFP exposes the full peripheral set: ample digital I/O, the full LCD segment bus, and CTMU-driven touch channels, which is why designers typically pick the 80-pin variants over the 64-pin PIC18F66K90 family members when the application needs more glass real-estate and more touch keys.
Typical applications include battery-powered medical devices such as glucose meters and portable patient monitors, industrial panel meters and process transmitters with LCD readouts, home appliances with segment displays, security keypads with capacitive touch, and consumer devices requiring long battery life combined with on-glass graphics. The CTMU simplifies touch-interface designs by measuring capacitance changes without an external analog front end.
When designing with this part, allocate the lower 16 addresses of Flash for the interrupt vector table and use MPLAB XC8 PRO mode for code-density. For LCD applications, follow Microchip's AN658 LCD fundamentals application note for bias and contrast resistor selection, and verify that the segment and common pin assignments fit within the 192-segment maximum of the 80-pin package. Industrial users should confirm the 'I' suffix (-40°C to +85°C) versus the 'E' (-40°C to +125°C) variant when targeting harsher environments.
This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Mga alternatibo na pwedeng ilagay na PIC18F86K90-I/PTRSL — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok PIC18F86K90-I/PTRSL (parehas na form factor at footprint) — pagkakaiba sa Package, LCD Driver, Operating Temperature, ADC, CTMU.
PIC18F87K90-I/PTRSL
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
PIC18F87K90T-I/PTRSL
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PIC18F86K90-I/PT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PIC18F86K90T-I/PTRSL
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
PIC18F85K90-I/PTRSL
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PIC18F85K90T-I/PTRSL
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →PIC18F86K90-I/PTRSL Mga Pinakamataas na Rating at Electrical Characteristics
| Core Architecture | PIC18 (8-bit RISC) |
| Family | PIC® XLP™ 18K |
| Sub-family | PIC18FxxK90 (LCD driver) |
| Program Memory (Flash) | 64 KB (32K x 16) |
| RAM | 4 KB |
| Maximum CPU Frequency | 64 MHz |
| Instruction Throughput | 16 MIPS |
| Supply Voltage (VDD) | 1.8 V to 5.5 V |
| Temperature na Operasyon | -40 °C to +85 °C (Industrial, 'I' grade) |
| Packhaging | 80-pin TQFP (PT), 12x12 mm |
| Uri ng Pagpapasok | Surface Mount |
| Packaging Format | Tape & Reel (TR) |
| LCD Driver | Up to 192 segments integrated |
| ADC | 12-bit, multi-channel (channel count per datasheet) |
| CTMU | Yes (Charge Time Measurement Unit for touch) |
| nanoWatt XLP Technology | Yes (ultra-low-power sleep modes) |
| Tindminan RoHS | Compliant |
Gabay sa Pin Configuration ng PIC18F86K90-I/PTRSL 80-pin tqfp (pt), 12x12 mm
Pin configuration para sa PIC18F86K90-I/PTRSL (80-pin tqfp (pt), 12x12 mm package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa PIC18F86K90-I/PTRSL.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
PIC18F86K90-I/PTRSL ay nararapat para sa 6 aplikasyons: Battery-Powered Medical Meter, Industrial Panel Meter / Process Transmitter, Home Appliance Segment Display, Security Keypad with Capacitive Touch, Portable Consumer Device with Graphical LCD, Smart Home Sensor Node with Display.
Battery-Powered Medical Meter
The PIC18F86K90-I/PTRSL fits battery-powered medical meters because its nanoWatt XLP™ sleep currents in the nanoamp range extend coin-cell life across multi-year service intervals. The integrated 192-segment LCD driver eliminates an external segment-driver IC and the 12-bit ADC captures measurements from analog sensor front-ends. The CTMU adds reliable capacitive buttons for the user interface without a separate touch controller. At 64MHz/16 MIPS, the device can run measurement DSP, encrypt telemetry, and refresh the LCD without compromising response latency.
Inirekomenda
Industrial Panel Meter / Process Transmitter
Industrial panel meters benefit from the PIC18F86K90-I/PTRSL's 1.8V-5.5V VDD range, -40°C to +85°C industrial temperature grade, and 4KB RAM that buffers fieldbus protocol stacks such as HART or Modbus. The 192-segment LCD capability supports a 4-digit numeric display plus engineering units and status icons. The CTMU enables sealed-front-panel capacitive keys with no mechanical buttons, improving IP65+ ingress protection. Designers can use MPLAB Code Configurator to spin up UART, I²C, and ADC peripherals in minutes.
Inirekomenda
Home Appliance Segment Display
Microwave ovens, washing machines, and induction cooktops use the PIC18F86K90-I/PTRSL to drive large segmented LCD or LED displays while keeping touch-button user interfaces responsive. The 64KB Flash holds user-interface state machines and menu logic, while the 4KB RAM runs display refresh buffers. The 12-bit ADC reads temperature, humidity, or load sensors with sufficient resolution for closed-loop control. nanoWatt XLP™ sleep modes allow standby power below 1 µA, satisfying Energy Star idle requirements.
Inirekomenda
Security Keypad with Capacitive Touch
Security keypads that need PIN entry plus a status display benefit from the PIC18F86K90-I/PTRSL's CTMU, which supports up to 24 capacitive touch channels without an external touch controller. The integrated LCD driver drives 192 segments-enough for a 16-digit PIN pad plus icons for armed, alarm, fault, and battery states. The 8-bit PIC18 core handles AES-style authentication routines in firmware, and nanoWatt XLP™ sleep extends battery life in wireless sensors. The wide 1.8V-5.5V VDD range simplifies battery management.
Inirekomenda
Portable Consumer Device with Graphical LCD
Portable consumer devices such as e-bike displays, personal health trackers, and remote controls use the PIC18F86K90-I/PTRSL because it drives the LCD glass, runs the user interface, and reads sensors with a single IC. The 64KB Flash holds firmware graphics, and the 4KB RAM buffers display frames. The 12-bit ADC captures battery voltage and analog sensor data, while multiple UART/SPI/I²C ports connect to Bluetooth or Wi-Fi modules. The wide VDD range supports direct Li-ion battery operation down to 3.0V cutoff.
Inirekomenda
Smart Home Sensor Node with Display
Smart-home sensors such as indoor air-quality monitors, thermostat remotes, and energy meters pair the PIC18F86K90-I/PTRSL with a small LCD to surface readings without needing a smartphone app. The CTMU supports touch buttons, the LCD driver displays readings, and the 64KB Flash fits Zigbee or Matter protocol stacks. The 16 MIPS throughput processes sensor data and encryption, while nanoWatt XLP™ sleep enables multi-year battery life on 2xAA cells. The wide 1.8V-5.5V VDD accommodates battery voltage droop without brown-out issues.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for PIC18F86K90-I/PTRSL — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | PIC18F87K90-I/PTRSL | PIC18F87K90T-I/PTRSL | PIC18F86K90-I/PT | PIC18F85K90-I/PTRSL | PIC18F85K90T-I/PTRSL |
|---|---|---|---|---|---|---|
| Package | 80-pin TQFP (PT), 12x12 mm | 80-pin TQFP (PT), 12x12 mm | 80-pin TQFP (PT), 12x12 mm | 80-pin TQFP (PT), 12x12 mm | 80-pin TQFP (PT), 12x12 mm | 80-pin TQFP (PT), 12x12 mm |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 128 KB | 128 KB | 64 KB | 32 KB | 32 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB | 2 KB | 2 KB |
| Maximum Clock | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS |
| LCD Segments (max) | 192 | 192 | 192 | 192 | 192 | 192 |
| CTMU (Touch) | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Temperature Grade | -40 °C to +85 °C (Industrial) | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Pangunahing mga Pagkakaiba
- Largest Flash within the 80-pin PIC18FxxK90 K90 family with PTRSL packaging (kumpara saPIC18F85K90-I/PTRSL)
- Industrial temperature range with I-grade suffix (kumpara saPIC18F86K90-E/PTRSL)
- PTRSL suffix delivers ready-to-feed tape-and-reel format for high-volume SMT (kumpara saPIC18F86K90-I/PT (tray))
- Integrated CTMU touch controller eliminates external touch IC (kumpara saGeneric 8-bit MCU without CTMU)
Talaan ng Disenyo
Estimated: at 64MHz active, the PIC18F86K90-I/PTRSL core draws roughly 8-12 mA from 3.3V, dominated by the LCD driver and I/O switching. In Sleep mode with nanoWatt XLP™ enabled, current drops to under 100 nA typical, allowing multi-year battery life in metering applications. Use the Microchip MPLAB XC8 POWER_DEBUG plugin and AN1414 to characterize your actual application current before committing to a battery chemistry.
Decouple VDD with a 100 nF ceramic placed within 5 mm of each VDD/AVDD pin pair, plus a bulk 10 µF tantalum or ceramic. The LCD driver charge-pump output (VLCD) and bias pins (LCDBIASx) need their own 100 nF capacitors close to the pins per application note AN658. Use a star-ground topology tying AGND to DGND at a single point beneath the IC, and keep the high-frequency MCU traces away from the LCD glass connector.
Do not skip the configuration bits (CONFIG1L-3H) or set the wrong oscillator mode - the device defaults to internal oscillator but defaults may not be optimal for USB or timing-critical peripherals. Verify the Vcap pin (if present in your package variant) has a 10 µF capacitor, and confirm the LCD segment/common pin assignments do not collide with CTMU touch channels when both features are used simultaneously on the same pin. Always check the latest PIC18F87K90 silicon errata (DS80000542) for known anomalies before locking the PCB layout.
When driving longer traces to the LCD glass (typically a 1-3 cm flex cable), add 1-10 kΩ series resistors on each segment line to dampen overshoot from the high-impedance LCD outputs. For CTMU touch channels, keep the touch electrode traces short, guarded by a ground plane, and away from switching signals. The Microchip AN1250 CTMU application note gives PCB layout guidelines for robust capacitive touch sensing.
Impormasyon ng Pagsunod sa Kautusan
RoHS and REACH compliance per Microchip product page. Halogen-free per Microchip material declarations. PIC18F86K90 family is not AEC-Q100 qualified; for automotive use, review Microchip's PIC18F87K90 automotive-grade variants or the dsPIC33 family.