SN65HVD73D - 20Mbps Full-Duplex RS-485 | TI
MPN: SN65HVD73D ✓ NakahandaSN65HVD73D Ulas
An RS-485 transceiver is a physical-layer interface IC that converts low-voltage digital logic signals into differential bus signals and reconstructs logic-level data from a differential bus. It belongs to the transceiver hierarchy within interface ICs and enables robust, point-to-point or multidrop communication over longer distances than single-ended logic interfaces. Full duplex means the driver and receiver can operate simultaneously on separate differential pairs.
The SN65HVD73D's principal features include a 20 Mbps data rate, 70 mV receiver hysteresis, separate active-high driver enable and active-low receiver enable controls, and ±12 kV IEC-rated ESD protection. Its 3 V to 3.6 V operating range is appropriate for 3.3 V systems. The broad -40°C to +125°C temperature range supports industrial and extended-temperature equipment when the complete system qualification permits it.
The integrated driver and receiver provide one RS-485/RS-422 communication channel in full-duplex configuration. Separate enables allow the transmitter and receiver to be disabled independently, and the manufacturer product page states that standby current can be reduced below 5 µA when both functions are disabled. A common ground reference and carefully terminated differential wiring remain necessary for reliable operation.
Typical applications include industrial control networks, factory automation equipment, data acquisition systems, building-automation controllers, and communications between a host controller and a peripheral transceiver. The 20 Mbps capability supports high-speed point-to-point links, while the ±12 kV IEC ESD rating helps protect external bus connectors in electrically noisy environments.
Designers should follow the manufacturer datasheet for transceiver pinout, termination, fail-safe biasing, and differential routing. Keep the RS-485 differential pair routed as a controlled-impedance pair, minimize stub lengths, place termination only where required by the bus topology, and verify grounding and surge-protection requirements for the installed environment.
This product summary consolidates verified manufacturer and distributor information, supply parameters, design guidance, and replacement constraints into one engineering-focused reference. It also clearly distinguishes verified specifications from electrical values that require confirmation from the complete datasheet before schematic release.
Mga alternatibo na pwedeng ilagay na SN65HVD73D — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboSN65HVD73D Mga Spesipikasyon
| Product Type | RS-485/RS-422 Full-Duplex Transceiver |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 20 Mbps |
| ESD Protection | ±12 kV IEC |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Duplex Mode | Full Duplex |
| Supported Protocols | RS-422 and RS-485 |
| Receiver Hysteresis | 70 mV |
| Driver Enable | Active High |
| Receiver Enable | Active Low |
| Standby Current | Less than 5 µA with driver and receiver disabled |
| Hanay ng Temperature na Operasyon | -40°C to +125°C |
| Packhaging | 14-pin SOIC (D) |
| Uri ng Pagpapasok | Surface Mount |
| Shipping Packaging | Tube |
| Katayuan ng Lifecycle | Active |
Gabay sa Pin Configuration ng SN65HVD73D 14-pin soic (d)
Pin configuration para sa SN65HVD73D (14-pin soic (d) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa SN65HVD73D.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
SN65HVD73D ay nararapat para sa 6 aplikasyons: Industrial Automation Fieldbus Interface, Factory Sensor and Actuator Networking, High-Speed Data Acquisition Equipment, Building Automation Controller, Power and Energy Monitoring Equipment, Communications and Network Equipment.
Industrial Automation Fieldbus Interface
The SN65HVD73D fits a high-speed industrial controller that must exchange differential data with remote field equipment while transmitting and receiving at the same time. Its 20 Mbps maximum data rate supports modern machine-control and data-acquisition links, while the 3 V to 3.6 V supply range integrates with 3.3 V logic. The full-duplex architecture uses separate driver and receiver paths, avoiding contention on a shared pair. The ±12 kV IEC ESD rating adds connector-level protection, although surge, immunity, grounding, and cable requirements must be verified separately for the installed machinery.
Inirekomenda
Factory Sensor and Actuator Networking
The SN65HVD73D can connect a controller to distributed sensors or actuators when the installation benefits from independent transmit and receive paths. Its one-driver, one-receiver configuration and 20 Mbps capability accommodate modern digital equipment, while 70 mV receiver hysteresis helps distinguish valid differential states. Because the device operates from 3 V to 3.6 V, it fits 3.3 V industrial control boards. Designers must plan the differential pair as a controlled-impedance route, minimize branch stubs, and determine whether termination or fail-safe biasing is required at each end of the installed cable.
Inirekomenda
High-Speed Data Acquisition Equipment
The SN65HVD73D is appropriate for a data-acquisition chassis that must return sensor or instrument data to a host controller over a full-duplex differential link. The 20 Mbps rate provides ample link margin for many short-distance laboratory and industrial cables, and the receiver's 70 mV hysteresis supports clean digital recovery. Its 14-pin SOIC package is practical for conventional surface-mount assembly. At the board level, route the A and B conductors as a pair, provide a low-impedance return path, control connector stubs, and verify receiver thresholds and cable attenuation at the selected operating distance.
Inirekomenda
Building Automation Controller
The SN65HVD73D can support full-duplex communications between a building controller and remote room or equipment controllers. The 3.3 V operating range suits modern embedded control boards, and the broad -40°C to +125°C specification provides margin for temperature-controlled equipment. Its independent active-high driver enable and active-low receiver enable allow firmware to control the two interface directions, including a low-power state below 5 µA when both are disabled. The finished design still needs appropriate cable routing, grounding, connector protection, and qualification for the building environment.
Inirekomenda
Power and Energy Monitoring Equipment
The SN65HVD73D is suitable for energy-monitoring equipment that communicates measurements from a remote meter or monitoring unit to a concentrator. Full-duplex operation permits simultaneous command transmission and measurement reporting, while the 20 Mbps capability supports high-speed local links. The 3.3 V supply range and 14-pin SOIC package align with compact embedded control hardware. Ensure that the bus cable is installed according to its environmental class, maintain a continuous reference path between communicating nodes, and separate or filter noisy power stages to avoid coupling disturbances into the differential receiver.
Inirekomenda
Communications and Network Equipment
The SN65HVD73D can terminate a full-duplex RS-485 or RS-422 link inside routers, gateways, protocol converters, and network-interface modules. Its 20 Mbps maximum rate supports short, high-speed links, while separate enable inputs give the host controller explicit control over the driver and receiver. The ±12 kV IEC ESD protection is useful where an internal board connects to an external panel connector. For reliable operation, keep the transceiver close to the connector, keep the connector-to-transceiver differential route short and impedance-controlled, and validate the complete interface under cable, ground-potential, and transient conditions.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for SN65HVD73D — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | Texas Instruments |
| Package | 14-pin SOIC (D) |
| Supply Voltage Range | 3 V to 3.6 V |
| Maximum Data Rate | 20 Mbps |
| Duplex Mode | Full Duplex |
| Drivers/Receivers | 1/1 |
| Supported Protocols | RS-422 and RS-485 |
| Receiver Hysteresis | 70 mV |
| ESD Protection | ±12 kV IEC |
| Operating Temperature Range | -40°C to +125°C |
Pangunahing mga Pagkakaiba
- Full-duplex operation with independent enable controls (kumpara saSN65HVD73DR)
- High verified signaling rate (kumpara saSN65HVD06D)
- Panel-interface ESD resilience (kumpara saSN65HVD1470D)
Talaan ng Disenyo
Route the two RS-485 conductors as a controlled-impedance differential pair from the transceiver to the connector, using matched geometry and a continuous reference plane. Keep the transceiver close to the connector, minimize connector-to-IC distance, and avoid stubs that create reflections. Keep unrelated switching nodes and crystal or clock routing away from the receiver input. Where the cable interface crosses a board partition or chassis boundary, provide a defined ground and surge-protection strategy rather than relying only on the transceiver's ±12 kV IEC ESD feature.
Do not assume that every SN65HVD7x-family device is pin-to-pin compatible with the SN65HVD73D. The verified TI ordering information distinguishes devices with fully enabled operation from those with active-high driver enables and active-low receiver enables, but enable polarity alone does not establish package compatibility. Before substituting any family member, compare the official pin assignments, differential output pins, receiver-output pins, enable pins, supply pins, and exposed-pad requirements. Also verify that the candidate supports the intended protocol and data rate.
Use a stable 3.3 V supply within the verified 3 V to 3.6 V operating range, and place local bypass capacitance close to the device's supply and ground connections. Confirm the required capacitor value, voltage rating, and layout against the complete manufacturer datasheet. Keep the receive-side and transmit-side return current within the transceiver ground reference, and avoid sharing narrow ground paths with high-current loads. The manufacturer states that standby current can fall below 5 µA when both driver and receiver are disabled, making enable-state planning important for low-power systems.
Determine termination and fail-safe biasing from the actual cable topology rather than adding components by habit. Full-duplex systems commonly place termination at the ends of each differential pair, while multidrop arrangements require careful analysis of branches and reflections. Evaluate the receiver's 70 mV hysteresis against the cable loss, common-mode noise, ground offset, and transmitted signal amplitude. Use the manufacturer's recommended test conditions to verify the 20 Mbps operating limit with the intended cable length and connector rather than assuming the headline data rate applies to every installation.
Impormasyon ng Pagsunod sa Kautusan
The supplied verified data explicitly references IEC ESD protection and an operating range of -40°C to +125°C, but it does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields remain unknown rather than being inferred.