PABALIKANG MAGBILI NG IKAKATUWID: TJA1050T/H/V ay papalapit sa katapusan ng buhay. Huling pagsugod ng order: Magkontak sa amin. Tingnan ang mga magagamit na alternatibong bahagi →
NXP Semiconductors

TJA1050T/H/V - 1 Mbaud 5V CAN Transceiver | NXP

MPN: TJA1050T/H/V ✗ Tapus ng Buhay
5 V Vdss 8-pin SOIC Package Improved relative to earlier CAN transceiver generations Memory
MOQ: 1 |

TJA1050T/H/V Ulas

NXP Semiconductors TJA1050T/H/V is a 5 V high-speed CAN transceiver supporting data rates up to 1 Mbaud in an 8-pin SOIC package. It provides a differential interface between a CAN protocol controller and a two-wire CAN bus, combining differential transmission, differential reception, transmitter silent mode, and a TXD dominant timeout function.

A CAN transceiver is a physical-layer interface within the Controller Area Network communication hierarchy. It translates logic-level TXD and RXD signals into the dominant and recessive voltage states carried by CANH and CANL. The differential bus arrangement supports noise rejection and allows multiple nodes to communicate over a shared two-wire network in automotive, industrial, and control systems.

Key features of the TJA1050T/H/V include a 1 Mbaud maximum signaling rate, a nominal 5 V supply, operation from a 4.75 V to 5.25 V supply range, and an 8-pin SOIC package. Silent mode disables the transmitter while retaining receiver operation, while the TXD dominant timeout prevents the bus from remaining permanently dominant if TXD is held low by a controller or software failure.

The device supports differential transmit and receive communication and is intended to connect a CAN controller to a physical CAN bus. Its bus pins are protected against electrical stress, and an unpowered node does not disturb the bus lines. The TJA1050 also provides improved electromagnetic-emission behavior compared with earlier CAN transceiver generations, an important consideration in compact embedded equipment.

Typical uses include automotive body and powertrain control modules, industrial automation equipment, machine controllers, robotics, elevator systems, and service-bus networks. The 1 Mbaud capability supports both conventional automotive CAN traffic and faster industrial CAN systems, although the complete bus must be designed for the intended bit rate, termination, topology, and electromagnetic environment.

When laying out the PCB, place the transceiver close to the CANH and CANL connector or transceiver connector, provide the specified bus termination only at the two physical ends of the bus, and keep the CAN pair routed together with continuous reference to the ground plane. Decoupling capacitors should be placed close to VCC and GND, while protection components should be selected to preserve differential bus behavior.

This product page combines the manufacturer specification, ordering information, lifecycle status, alternative ordering codes, and practical replacement guidance. It also distinguishes genuine same-package drop-in choices from newer transceivers that require different voltage, pin, standby, or common-mode implementation decisions.

Mga alternatibo na pwedeng ilagay na TJA1050T/H/V — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

TJA1050T/CM,118

✅ Drop-In
📦 8-pin SOIC
Same 5 V and 1 Mbaud CAN transceiver ratings with a 0% difference in those key parameters; qualification and temperature attributes require verification.

📋 Alternatibo na Reference (hindi sa katalogo)

TJA1050T/VM,118

✅ Drop-In
📦 8-pin SOIC
Same 5 V and 1 Mbaud CAN transceiver ratings with a 0% difference in those key parameters; ordering-code attributes require verification.

📋 Alternatibo na Reference (hindi sa katalogo)

TJA1050T/118,112

✅ Drop-In
📦 8-pin SOIC
Same 5 V and 1 Mbaud CAN transceiver ratings with a 0% difference in those key parameters; delivery and qualification attributes require verification.

📋 Alternatibo na Reference (hindi sa katalogo)

TJA1050T/V,112

✅ Drop-In
📦 8-pin SOIC
Same 5 V and 1 Mbaud CAN transceiver ratings with a 0% difference in those key parameters; temperature and delivery attributes require verification.

📋 Alternatibo na Reference (hindi sa katalogo)

TJA1050T/H/V,118

✅ Drop-In
📦 8-pin SOIC
Same 5 V and 1 Mbaud CAN transceiver ratings with a 0% difference in those key parameters; ordering and packaging attributes require verification.

📋 Alternatibo na Reference (hindi sa katalogo)

TJA1050T/H/V Mga Spesipikasyon

Product Type High-speed CAN transceiver
CAN Bus Data Rate Up to 1 Mbaud
Nominal Supply Voltage 5 V
Supply Voltage na Operasyon 4.75 V to 5.25 V
Supply Pin Count 1 VCC pin
Ground Pin Count 1 GND pin
Differential Transmit Capability Yes
Differential Receive Capability Yes
Transmitter Silent Mode Yes
TXD Dominant Timeout Yes
Unpowered Node Bus Disturbance No disturbance of the bus lines
Bus Pin Protection Protected
Packhaging 8-pin SOIC
Uri ng Pagpapasok Surface mount
Electromagnetic Emission Performance Improved relative to earlier CAN transceiver generations
Tindminan RoHS unknown
REACH Status unknown

Pin Configuration ng TJA1050T/H/V

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 TXD — Transmit data input from the CAN controller
Pin 2 GND — Ground connection
Pin 3 VREF — Voltage reference output used for common-mode control
Pin 4 RXD — Receive data output to the CAN controller
Pin 5 VCC — 5 V supply connection
Pin 6 CANL — CAN low bus terminal
Pin 7 CANH — CAN high bus terminal
Pin 8 S — Silent-mode input

Tipikal na mga Gamit

TJA1050T/H/V ay nararapat para sa 6 aplikasyons: Automotive Body Control Module, Industrial Automation Controller, Robotics Motor Network, Machine Tool Communication, Elevator and Building Control, Legacy CAN Test and Service Tool.

🚗

Automotive Body Control Module

The TJA1050T/H/V fits an automotive body control module that connects a CAN controller to door, lighting, climate, or seat-control nodes. Its 1 Mbaud capability accommodates conventional high-speed CAN networks, while differential transmission and reception support reliable signaling over a shared two-wire bus. The TXD dominant timeout can prevent a controller failure from holding the network dominant indefinitely. Because the device is legacy and listed as end of life, an existing module can retain its 8-pin SOIC layout, but a new platform should also evaluate current-generation transceivers with suitable low-power and fault-protection features.

🏭

Industrial Automation Controller

The TJA1050T/H/V can connect an industrial controller to remote actuators, sensors, drives, or operator panels over a CAN bus. A nominal 5 V supply and operation up to 1 Mbaud suit embedded 5 V control platforms, while the differential physical layer helps reject common-mode noise found around motors and switching equipment. The 8-pin SOIC footprint simplifies use in compact control boards. Design the bus according to the manufacturer's application guidance, including termination at the two ends, controlled stub lengths, and placement of the transceiver near the bus connector.

🏭

Robotics Motor Network

The TJA1050T/H/V is suitable for CAN-based robot coordination when motors and actuators communicate through a common bus. The 1 Mbaud rate allows higher bus activity than lower-speed serial links, and the differential CAN interface supports communication between distributed modules. Silent mode provides a way to disable transmission during selected test or shutdown states without removing the physical interface. The bus layout should keep CANH and CANL paired, use a continuous ground reference, and separate high-current motor paths from the transceiver and controller traces.

🏭

Machine Tool Communication

A machine-tool controller can use the TJA1050T/H/V to communicate with distributed I/O, servo drives, safety-related monitoring modules, and service interfaces. The 5 V operating range is compatible with conventional embedded CAN controller platforms, and the 8-pin SOIC package supports compact, surface-mounted assemblies. The differential bus reduces susceptibility to common-mode industrial noise, but correct termination and topology remain essential at 1 Mbaud. For new machine platforms with long lifecycle requirements, evaluate the obsolete status alongside newer CAN transceivers that may offer enhanced bus-fault handling.

🏭

Elevator and Building Control

The TJA1050T/H/V can serve as the physical-layer interface in elevator controllers, door systems, and building-control nodes that exchange commands over CAN. Its 1 Mbaud capability supports compact control networks with several communicating units, while differential signaling helps maintain reliable operation around relays, lighting electronics, and motor equipment. The transmitter silent mode is useful when a node must monitor without asserting the bus. Keep the CAN pair away from high-energy switching traces and verify that cable length and node spacing remain appropriate for the selected signaling rate.

🔧

Legacy CAN Test and Service Tool

The TJA1050T/H/V can be retained in a diagnostic fixture or service tool designed for an existing 5 V CAN controller and SO-8 layout. Its differential receiver supports bus monitoring, while silent mode permits a tester to observe traffic without driving the network. The TXD dominant timeout protects the bus if the test host fails during transmission. Since this is an end-of-life device, service equipment should use controlled procurement and verify the exact ordering attributes before assembly. New test tools should assess contemporary CAN transceivers with programmable standby or diagnostic functions.

Buod ng mga Inirekomendang Produkto

TJA1050T/CM,118 Same-family 5 V CAN transceiver candidate Ginagamit sa: Automotive Body Control Module, Robotics Motor Network, Legacy CAN Test and Service Tool TJA1050T/VM,118 Same-family 5 V CAN transceiver candidate Ginagamit sa: Automotive Body Control Module, Machine Tool Communication, Legacy CAN Test and Service Tool TJA1050T/118,112 Same-family industrial CAN interface candidate Ginagamit sa: Industrial Automation Controller, Machine Tool Communication TJA1050T/V,112 Same-family industrial CAN interface candidate Ginagamit sa: Industrial Automation Controller, Elevator and Building Control TJA1050T/H/V,118 Same-family CAN transceiver ordering variant Ginagamit sa: Robotics Motor Network, Elevator and Building Control
What is the TJA1050T/H/V?
The TJA1050T/H/V is an NXP Semiconductors high-speed CAN transceiver that connects a CAN protocol controller to a two-wire CAN bus. According to the NXP TJA1050 product specification, it supports differential transmit and receive communication, signaling rates up to 1 Mbaud, a 5 V nominal supply, and an 8-pin SOIC package. It is intended for automotive and industrial CAN networks where a controller requires a physical-layer bus interface.
What is the operating voltage of TJA1050T/H/V?
The TJA1050T/H/V operates from a 4.75 V to 5.25 V supply with a nominal operating voltage of 5 V. The NXP TJA1050 product specification identifies the device as a 5 V high-speed CAN transceiver. A 5 V controller interface and appropriately decoupled supply rail are therefore required; the transceiver should not be operated from a 3.3 V-only rail without a suitable interface and power solution.
What is the maximum CAN data rate of TJA1050T/H/V?
The TJA1050T/H/V supports CAN signaling up to 1 Mbaud. The NXP TJA1050 product specification describes the device as a high-speed CAN transceiver with a maximum rate of 1 Mbaud. Actual network performance also depends on cable length, topology, termination, transceiver propagation characteristics, controller timing, electromagnetic conditions, and the number and placement of bus nodes.
Where can I download the TJA1050T/H/V datasheet?
The TJA1050T/H/V datasheet PDF is available from the official NXP page at https://www.nxp.com/docs/en/data-sheet/TJA1050.pdf. The document is titled “PDF TJA1050 High speed CAN transceiver” and identifies itself as the NXP product specification. Use its pin-description table, electrical characteristics, application diagram, and ordering information when assigning PCB nets and verifying operating limits.
Where is the TJA1050T/H/V pinout?
The TJA1050T/H/V uses an 8-pin SOIC configuration with TXD, GND, VREF, RXD, VCC, CANL, CANH, and S functions. The manufacturer datasheet is the authoritative source for assigning each signal. Keep CANH and CANL as a routed differential pair, connect the transceiver ground to the board ground plane, and use the pin-description table to avoid confusing the RXD output with the TXD input.
What does silent mode do on the TJA1050T/H/V?
Silent mode disables the TJA1050T/H/V transmitter so the device does not actively drive the CAN bus, while the receiver remains available for monitoring bus activity. The NXP TJA1050 product specification identifies silent mode as a core feature. It is useful during controlled shutdown, diagnostics, or test states where bus communication must stop without removing the transceiver from the circuit.
What is TXD dominant timeout on TJA1050T/H/V?
The TXD dominant timeout disables the transmitter if the TXD input remains low longer than the internal timeout interval. The NXP TJA1050 product specification states that this prevents the bus lines from being driven into a permanent dominant state when a hardware or software failure holds TXD low. The timeout improves network availability by allowing other nodes to continue communicating instead of being blocked by one failed node.
Where can I buy TJA1050T/H/V and check its lead time?
Use the Request a Quote form on this page to request TJA1050T/H/V availability, current lead time, and order quantity. The manufacturer lists the TJA1050 family as end of life, so procurement should include lifecycle confirmation and a documented obsolete-parts plan. Confirm the exact ordering code and delivery condition before committing a replacement design to production.
What is the price of TJA1050T/H/V?
The current TJA1050T/H/V quotation is provided through the Request a Quote form on this page. Because the TJA1050 family is listed as end of life, the commercial terms can vary with quantity, condition, and procurement timing. Submit the required quantity and target date through the quote form so the order can be evaluated against the current supply position.
Is TJA1050T/H/V currently in stock?
TJA1050T/H/V is subject to end-of-life supply conditions, so current stock should be confirmed through the Request a Quote form on this page. The NXP product page identifies the TJA1050 as end of life. For new production, request a supply schedule and consider a qualified replacement strategy rather than depending on an unconfirmed single shipment.
What is the lead time for TJA1050T/H/V?
The Request a Quote form on this page is the appropriate route for the current TJA1050T/H/V lead time. Because the manufacturer lists the device as end of life, availability can be constrained and may depend on remaining factory inventory, authorized-channel supply, and the quantity ordered. Include your production schedule and required date when requesting the quotation.
What is the best drop-in replacement for TJA1050T/H/V?
The closest drop-in choices are ordering-code members of the NXP TJA1050 family that retain the same SO-8 footprint and 5 V, 1 Mbaud CAN transceiver architecture. The TJA1050T/CM,118, TJA1050T/VM,118, TJA1050T/118,112, and TJA1050T/V,112 appear in cross-reference results. Their qualification, temperature, or delivery attributes must be checked against the original requirements before production release.
Can TJA1050T/CM,118 replace TJA1050T/H/V?
TJA1050T/CM,118 can be considered as a same-family drop-in candidate because it is identified as a high-speed CAN transceiver and appears in direct comparison results with TJA1050T/H/V,118. Before substitution, verify the exact pin functions, operating-temperature grade, qualification level, supply range, order quantity, and delivery form. A shared SOIC footprint alone does not prove that every ordering attribute is interchangeable.
TJA1050T/H/V vs TJA1051T/3 - which is better for a new CAN design?
TJA1050T/H/V is preferable when an existing 5 V design needs a direct, low-disruption replacement path, while TJA1051T/3 may suit a new design that benefits from a controller interface operating from 3 V to 5 V. The TJA1051T/3 comparison identifies operation from 3 V to 5 V, but it is not treated here as a guaranteed drop-in because standby, pin behavior, and application-level requirements must be compared.
When should I choose TJA1050T/H/V over a newer CAN transceiver?
Choose TJA1050T/H/V when maintaining an existing PCB, avoiding transceiver redesign, and preserving the original 5 V CAN interface has more value than adopting newer low-power or standby features. The manufacturer lists the device as end of life, so this choice is best for controlled legacy support. For new designs with long product lifetimes, evaluate current-generation transceivers even when they require some schematic or firmware changes.
What are the key specifications of TJA1050T/H/V that engineers should know?
The principal TJA1050T/H/V specifications are a 4.75 V to 5.25 V supply, operation up to 1 Mbaud, differential CAN transmission and reception, silent mode, TXD dominant timeout, protected bus pins, and an 8-pin SOIC package. The NXP TJA1050 product specification also notes that an unpowered node does not disturb the bus lines and that electromagnetic-emission behavior was improved over earlier generations.
Is there a Texas Instruments equivalent for TJA1050T/H/V?
The TI E2E discussion identifies SN65HVD1050A-Q1 as a candidate to examine against TJA1050T, but it also highlights a functional pin difference: pin 5 on TCAN1051-Q1 is a no-connect, whereas SN65HVD1050A-Q1 assigns VREF to pin 5. Because VREF can affect bus common-mode behavior and stability, review the existing PCB and bus design rather than treating the part as an automatic drop-in replacement.

Impormasyon ng Talumpati sa Engineering for TJA1050T/H/V — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose TJA1050T/H/V when maintaining an existing 5 V CAN design where PCB changes are undesirable and the manufacturer lifecycle status is acceptable under a controlled procurement plan. Its 8-pin SOIC footprint, 1 Mbaud operation, differential interface, silent mode, and TXD dominant timeout preserve the established TJA1050 design method. Select a same-family TJA1050 ordering code when its qualification, temperature, or delivery attributes meet the original requirements. Do not automatically substitute TJA1051T/3, TJA1057T, or a TI transceiver: controller voltage, standby behavior, VREF implementation, bus-fault handling, and exact pin functions can differ. For new platforms with long service lives, compare current-generation CAN transceivers against the legacy device's protection, power consumption, common-mode range, and availability requirements.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto TJA1050T/CM,118 TJA1050T/VM,118 TJA1050T/118,112 TJA1050T/V,112 TJA1050T/H/V,118
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Product Type High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver
Maximum Data Rate 1 Mbaud 1 Mbaud 1 Mbaud 1 Mbaud 1 Mbaud 1 Mbaud
Nominal Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Operating Supply Range 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V
Transmitter Silent Mode Yes Yes Yes Yes Yes Yes
TXD Dominant Timeout Yes Yes Yes Yes Yes Yes
Lifecycle Status End of life End of life End of life End of life End of life End of life

Pangunahing mga Pagkakaiba

  • Maintains a 1 Mbaud CAN interface in the original 8-pin SOIC footprint (kumpara saTJA1051T/3)
  • Preserves the established TJA1050 family behavior for controlled legacy maintenance (kumpara saTJA1057T,118)
  • Supports deterministic protection against a permanently dominant TXD state (kumpara saSN65HVD1050A-Q1)

Talaan ng Disenyo

Route CANH and CANL as a close, continuous differential pair over a solid ground reference. Keep the transceiver near the bus connector or transceiver connector to minimize the unprotected stub, and avoid introducing test pads or routing discontinuities in the pair. At 1 Mbaud, trace geometry, external components, and connector transitions can materially affect signal integrity, so review the complete bus path rather than treating the PCB route as an isolated item.

Decouple the 5 V VCC pin close to the device with the capacitance specified by the NXP application guidance, and provide a low-impedance return to the ground plane. The transceiver's operating range is 4.75 V to 5.25 V, so verify supply tolerance, startup sequencing, and controller I/O levels across the complete board. Avoid placing switching-regulator high-current paths between the decoupling capacitor and VCC pin.

Do not use a 120 ohm termination resistor at every node; install the standard bus termination only at the two physical ends of the CAN bus. Also avoid leaving the VREF and silent-mode pins in electrically undefined states. Follow the manufacturer pin-description table for their configured levels. Incorrect termination or an undefined control input can cause reflections, unintended dominant states, or inconsistent behavior when the transmitter is disabled.

For industrial or automotive equipment, isolate the CAN bus from sources of electromagnetic interference and confirm the transceiver's common-mode behavior under the actual installation conditions. The differential interface improves noise rejection, but it does not remove the need for controlled topology, suitable cable routing, and common-mode margin. Review protection-component capacitance because excessive filtering at the connector can degrade edge quality at 1 Mbaud.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The manufacturer product information identifies the TJA1050 as end of life, but the available product pages do not state the requested compliance classifications.

Data napatotohanan sa: 2026-11-18 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

tja1050t datasheet tja1050t cm 118 datasheet tja1050t cm 118 nxp tja1050t schematic TJA1050T/H/V datasheet pdf TJA1050T/H/V pinout TJA1050T/H/V SOIC-8 TJA1050T/H/V 1 Mbaud CAN TJA1050T/H/V equivalent TJA1050T/H/V replacement TJA1050T/H/V vs TJA1051T/3 TJA1050T/H/V automotive CAN TJA1050T/H/V price TJA1050T/H/V stock

Mga kaugnay na Mga Komponente at mga Tuntunin

NXP Semiconductors TJA1050T/H/V TJA1050T/CM,118 TJA1050T/VM,118 TJA1050T/118,112 TJA1050T/V,112 TJA1050T/H/V,118 TJA1051T/3 TJA1057T,118 SN65HVD1050A-Q1 CAN transceiver CAN interface high-speed CAN Controller Area Network differential transceiver two-wire CAN bus physical-layer interface TXD RXD CANH CANL VREF silent mode TXD dominant timeout 8-pin SOIC surface mount 1 Mbaud 5 V transceiver common-mode voltage electromagnetic immunity
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ