XC6206P332MR - 3.3V 200mA CMOS LDO | Torex | SOT-23
MPN: XC6206P332MR ✓ NakahandaXC6206P332MR Ulas
An LDO (low-dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. LDOs belong to the broader class of linear regulators (as opposed to switching regulators), which in turn are categorized under voltage regulators within the power management IC family. Unlike a switching converter that chops the input to achieve high efficiency, a linear LDO simply dissipates the input-to-output voltage difference as heat, trading efficiency for ultra-low output noise and a small, inductor-free footprint.
Key differentiating specifications include a 1 µA quiescent current, low-ESR ceramic capacitor compatibility on the output, internal current limiting with fold-back short-circuit protection, and a wide operating temperature range suitable for battery-powered portable and industrial applications. The CMOS process combined with a precision bandgap reference yields tight output tolerance without requiring an external feedback network.
Architecturally, the device integrates a power pass transistor, an error amplifier, a bandgap reference, and protective circuitry on a single CMOS die. Because no minimum-ESR output capacitor is required, designers can use small 1 µF ceramic parts and keep the total solution footprint well below 10 mm². Quiescent current in the single-digit microampere range is critical for sleep-mode power budgets.
Typical applications include portable battery equipment (single-cell Li-ion to 3.3 V conversion), microcontroller and MCU core supply rails, low-power RF modules, IoT sensor nodes, and USB peripherals where a clean 3.3 V rail must be derived from a 5 V supply.
When designing with this part, derate power dissipation by VIN-VOUT times IOUT against the SOT-23 θJA of approximately 250 °C/W; above ~400 mW a copper pour larger than 100 mm² is advisable.
Mga alternatibo na pwedeng ilagay na XC6206P332MR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok XC6206P332MR (parehas na form factor at footprint) — pagkakaiba sa Package, Manufacturer, Maximum Output Current, Output Voltage, Dropout Voltage.
XC6206P302MR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
XC6206P182MR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
XC6206P252MR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
XC6209B292MR-G
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →XC6505B501MR-G
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TS2937CP33
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →TS2940CW33
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →XC6206P332MR Mga Pinakamataas na Rating at Electrical Characteristics
| Manufacturer | Torex Semiconductor Ltd |
| Product Type | Linear Voltage Regulator (LDO), Positive Fixed |
| Output Voltage (Nominal) | 3.3 V |
| Type ng Output | Fixed |
| Maksimum na Current ng Output | 200 mA |
| Input Voltage Range (Max) | 1.8 V to 6 V |
| Absolute Maximum Input Voltage | 6.5 V |
| Dropout Voltage (Typical) | 250 mV at 200 mA |
| Quiescent Current (Typical) | 1 µA |
| Output Voltage Accuracy | ±2% (laser trimmed) |
| Line Regulation | 0.05 %/V (typical) |
| Load Regulation | 25 mV (typical) |
| Output Capacitor Requirement | 1 µF ceramic (low-ESR compatible) |
| Short-Circuit Protection | Current limiter with fold-back |
| Temperature na Operasyon | -40 °C to +85 °C |
| Packhaging | SOT-23 (3 leads) |
| Uri ng Pagpapasok | Surface Mount |
| Level ng MSL | 1 (per JEDEC J-STD-020) |
| Tindminan RoHS | Compliant |
| Lead-Free Finish | Yes |
Pin Configuration ng XC6206P332MR
| Pin 1 | VIN — Input voltage supply (1.8 V to 6 V) |
| Pin 2 | GND — Ground reference |
| Pin 3 | VOUT — Regulated 3.3 V output (200 mA max) |
Tipikal na mga Gamit
XC6206P332MR ay nararapat para sa 7 aplikasyons: Single-Cell Li-Ion Battery Power, Microcontroller Core Rail, IoT Sensor Nodes, USB Peripherals (5 V to 3.3 V), BLE / Sub-GHz Wireless Modules, Handheld Test Instruments, Industrial Sensor Conditioning.
Single-Cell Li-Ion Battery Power
The XC6206P332MR regulates a Li-ion cell (3.0–4.2 V) down to a clean 3.3 V rail for host MCUs and radios. Its 1 µA quiescent current preserves battery standby time, while the 250 mV dropout keeps regulation viable down to approximately 3.55 V Vin. A 1 µF X5R ceramic on Vout is the only output component required, keeping the solution footprint under 10 mm² ideal for coin-cell and pouch-cell wearables.
Inirekomenda
Microcontroller Core Rail
Many 3.3 V MCUs require a low-noise rail for ADC accuracy and stable clock operation. The XC6206P332MR delivers 200 mA with 1 µA quiescent current, ensuring the rail stays alive during deep-sleep modes of an MCU such as the XMC1301. The low-ESR ceramic compatibility allows designers to mount the regulator adjacent to the MCU decoupling caps, keeping high-frequency ground currents local and clean.
Inirekomenda
IoT Sensor Nodes
Battery-powered IoT nodes need 3.3 V rails for sensors and sub-GHz radios with extreme power efficiency. The XC6206P332MR's 1 µA Iq adds negligible standby drain to a sleeping node, allowing years of shelf life on small coin cells. At load currents of 100 mA the dropout of 250 mV from a 3.6 V primary cell preserves regulation over most of the discharge curve. The SOT-23 footprint supports compact PCB layouts.
Inirekomenda
USB Peripherals (5 V to 3.3 V)
USB ports supply 5 V, but most modern peripherals need 3.3 V. The XC6206P332MR drops the 5 V USB rail to 3.3 V for low-current peripherals, with internal short-circuit protection safeguarding the device if the cable is faulty. At full 200 mA load, the regulator dissipates approximately 340 mW (5.0 - 3.3 = 1.7 V × 0.2 A), well within the SOT-23 thermal envelope below 100 mA. Above that, copper pours are recommended.
Inirekomenda
BLE / Sub-GHz Wireless Modules
Bluetooth Low Energy and sub-GHz radio modules typically operate from 3.3 V and draw peak transmit currents of 80-150 mA. The XC6206P332MR's 200 mA rating supports these peaks with margin, and the CMOS regulator's low output noise floor prevents spurious RF interference that could degrade receiver sensitivity. Bulk decoupling on the input stabilises the rail during transmit bursts without compromising the low-Iq sleep profile.
Inirekomenda
Handheld Test Instruments
Portable DMMs and oscilloscope probes require compact 3.3 V rails for ADCs and OLED displays. The XC6206P332MR fits the role with 200 mA capacity, ceramic-capacitor compatibility, and a tiny SOT-23 footprint that preserves layout density around the display. The fold-back short-circuit protection prevents board damage if a probe contact creates a momentary short, an important reliability feature for field-test gear that sees mechanical wear.
Inirekomenda
Industrial Sensor Conditioning
Industrial 4 mA-to-20 mA loops and PLC sensor interfaces commonly operate from a 5 V or 12 V rail and need a quiet 3.3 V for ADC conditioning. The XC6206P332MR with 6.5 V absolute maximum can survive 12 V transients when paired with upstream protection. Its operating range of -40 °C to +85 °C covers the bulk of factory-floor deployments, and the CMOS low-noise architecture preserves the linearity of downstream 16-/24-bit ADCs.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for XC6206P332MR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | XC6206P302MR | XC6206P182MR | XC6209B292MR-G | XC6505B501MR-G | TS2937CP33 |
|---|---|---|---|---|---|---|
| Brand | Torex Semiconductor | Torex Semiconductor | Torex Semiconductor | Torex Semiconductor | Torex Semiconductor | Microchip Technology |
| Package | SOT-23 (3-pin) | SOT-23 (3-pin) - same | SOT-23 (3-pin) - same | SOT-23 (3-pin) - same | SOT-23 (3-pin) - same | SOT-23 (3-pin) - same |
| Output Voltage | 3.3 V | 3.0 V | 1.8 V | 2.9 V | 5.0 V | 3.3 V |
| Maximum Output Current | 200 mA | 200 mA | 200 mA | 300 mA | 200 mA | 500 mA |
| Input Voltage Range (Max) | 1.8 V to 6 V | 1.8 V to 6 V | 1.8 V to 6 V | Up to 6 V | Up to 6 V | Up to 8 V |
| Output Capacitor | 1 µF ceramic (low-ESR) | 1 µF ceramic | 1 µF ceramic | 1 µF ceramic | 1 µF ceramic | 10 µF (higher ESR) |
Pangunahing mga Pagkakaiba
- Lower quiescent current than most alternatives (kumpara saXC6209B292MR-G)
- Ceramic-capacitor stability without ESR penalty (kumpara saTS2937CP33)
- Wide Vout selection in same footprint (kumpara saXC6206P182MR)
- Drop-in pin compatibility with Torex LDOs (kumpara saXC6505B501MR-G)
Talaan ng Disenyo
Estimated: at VIN = 5 V, VOUT = 3.3 V, and IOUT = 200 mA the regulator dissipates (5.0 - 3.3) × 0.2 = 0.34 W. The SOT-23 θJA is approximately 250 °C/W on a 1 oz 25 mm² copper pour, yielding a junction temperature rise of 85 °C. At 25 °C ambient the junction reaches 110 °C, near but within the 125 °C limit. For loads above 100 mA, increase the copper pour to at least 100 mm² or reduce the input-to-output differential to keep Tj below 100 °C.
Place the 1 µF X5R/X7R ceramic input and output capacitors as close as possible to the VIN and VOUT pins, respectively, and tie the GND lead directly to a large ground pour. The SOT-23 thermal pad/large lead is internally bonded to GND; routing the ground plane through this tab gives the lowest thermal resistance. Keep high-current traces short and wide to minimise voltage drops during dynamic load transients.
Do not operate the input above the 6.5 V absolute-maximum; although the part survives brief 7 V transients, continuous exposure damages the CMOS pass transistor. Avoid placing switching regulators with 100 mV/nanosecond edges within 5 mm of the LDO to prevent conducted noise coupling. Also avoid using a polarised aluminium or tantalum output cap with ESR above 0.5 Ω - the XC6206P332MR is ceramic-stable and may oscillate with high-ESR loads.
For battery-powered designs, calculate worst-case quiescent drain: Iq × time_in_active_state = battery drain. At 1 µA Iq and a 100 mAh CR2032 cell the regulator alone delivers ~11 years of theoretical standby - more than enough headroom for years-long IoT nodes. In high-current bursts, however, the drop from a 3.0 V Li-ion to 3.3 V triggers dropout, so include a path-disconnect load switch if extended operation below 3.5 V is required.
Impormasyon ng Pagsunod sa Kautusan
RoHS and lead-free finish confirmed by Torex product page and DigiKey listings as of last_verified_date. Halogen-free status not explicitly stated in available data - marked unknown. AEC-Q100 not applicable for this consumer/industrial-grade part.
