Z86C9620PSC - 20MHz ROMless 8-Bit Z8 MCU | Zilog | 64-Pin SDIP
MPN: Z86C9620PSC ✓ NakahandaZ86C9620PSC Ulas
A microcontroller is a complete single-chip computer: it integrates a CPU core, non-volatile program storage, RAM, timers, serial interfaces, and I/O ports on one die. Within the Z8 family the key architectural option is "ROMless", meaning the device contains no internal program memory and instead fetches code from an external EPROM or Flash memory chip through the address/data bus. That choice frees board space and lets the designer select code density independently, at the cost of one or two extra memory components and bus routing complexity.
Key features of this part include a 20 MHz maximum clock frequency, an 8-bit CMOS CPU core, a 64-pin through-hole package that is easy to hand- and machine-solder, and a broad set of on-chip I/O and timer resources typical of the Z8 line. Because the Z8 core is a Z80 derivative, existing Z80 assembler toolchains and Z8 application notes can be reused, shortening the learning curve for teams migrating from legacy 8-bit designs.
Architecturally, the Z86C9620 combines a pipelined 8-bit CPU with an external bus capable of addressing external code and data memory, plus dedicated port pins, timer/counter blocks, and serial peripheral interfaces. Clocking is externally supplied, so a crystal or oscillator network is required to reach the 20 MHz operating point; the maximum frequency is a datasheet limit rather than a guaranteed operating point for every peripheral configuration. Run-time behaviour depends on the external memory map, so the same silicon can serve very different products purely through firmware and memory sizing.
Typical deployments include industrial control panels, burner or programming stations, appliance controllers, HVAC and building-automation modules, motor and relay sequencers, instrument front panels, and legacy equipment retrofits where a 20 MHz 8-bit CPU with external program memory is sufficient. Because the package is a through-hole SDIP, the part is also well suited to prototypes and small production runs assembled on through-hole assembly lines.
The main design consideration for this controller is external memory: the board must provide a working EPROM or Flash device with a stable address and data bus, correct wait-state timing if the memory is slower than the CPU, and decoupling close to the memory pins. Because the 64-pin DIP footprint exposes both address and data lines, board layout must keep the bus short and clean, and unused port pins should be tied to defined levels so that reset behaviour stays deterministic.
Mga alternatibo na pwedeng ilagay na Z86C9620PSC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok Z86C9620PSC (parehas na form factor at footprint) — pagkakaiba sa Package Type, Product Type.
Z86C9620VSC
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →Z86C9640PSC
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
Z86C9440PSC
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
Z86C9620PSC Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 8-bit CMOS Microcontroller |
| CPU Core / Family | Z8 (Z80-derived 8-bit core) |
| Maksimum na Taktiko ng Oras | 20 MHz |
| Program Memory Architecture | ROMless (external program memory required) |
| Package Type | 64-pin SDIP, rectangular, through-hole |
| Package Code | SDIP |
| Number of Terminals | 64 |
| Terminal Form | Through-hole |
| Uri ng Pagpapasok | Through-hole |
| Temperature Grade | Commercial |
| Process Technology | CMOS |
| Bit Width | 8-bit |
| Datasheet Length | 46 pages |
Gabay sa Pin Configuration ng Z86C9620PSC sdip
Pin configuration para sa Z86C9620PSC (sdip package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa Z86C9620PSC.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
Z86C9620PSC ay nararapat para sa 6 aplikasyons: Industrial Control Panel Controller, Appliance and HVAC Sequencer, Programmer and Device Test Fixture, Building Automation and HVAC Gateway, Instrument Front Panel and Metering, Legacy Equipment Retrofit and Repair.
Industrial Control Panel Controller
The Z86C9620PSC fits burner, sequencer, and HMI control boards because the 20 MHz Z8 core executes the sequencer state machine and keypad scanning fast enough to leave headroom for protocol handling. With a 64-pin SDIP footprint, the controller occupies a standard through-hole board alongside external EPROM for firmware. Because the part is ROMless, code density can be scaled independently on the same board family. Design note: keep the address and data bus short, and decouple the external memory close to the memory pins.
Inirekomenda
Appliance and HVAC Sequencer
The Z86C9620PSC is used in appliance controllers and HVAC sequencers where a 64-pin through-hole controller drives relays, valves, and sense inputs under a fixed control algorithm. The 20 MHz clock rate gives ample margin for debounce timers and state sequencing, while the commercial temperature grade suits indoor enclosure environments. Because the MCU is ROMless, one board revision can serve multiple model variants by changing only the external memory contents. Watch the supply rail decoupling at the DIP pins, as long analog sensor traces share the same through-hole board.
Inirekomenda
Programmer and Device Test Fixture
In burner and programming fixtures, the Z86C9620PSC handles fixture sequencing, handshake timing, and pass/fail logging at 20 MHz, which shortens fixture cycle time compared with slower legacy 8-bit controllers. The 64-pin through-hole SDIP package simplifies fixture wiring and rugged through-hole assembly. Since the controller fetches code from external memory, the same fixture firmware can be re-targeted to different DUT families. Practical consideration: provide a clean ground reference plane, because fixture cabling can inject noise on the bus lines.
Inirekomenda
Building Automation and HVAC Gateway
The Z86C9620PSC is applied in building-automation nodes where it supervises sensor inputs, drives relay outputs, and maintains a serial link to a supervisory controller. Its 20 MHz Z8 core handles polling loops and protocol framing with margin, and the 64-pin DIP body is easy to replace in the field. The ROMless architecture suits product variants that share one board but differ in protocol or feature set via external memory contents. Design note: the commercial temperature grade constrains ambient use, so specify a wider-grade variant for unheated cabinets.
Inirekomenda
Instrument Front Panel and Metering
Front-panel instruments and utility metering designs use the Z86C9620PSC to drive displays, decode keypad input, and manage measurement acquisition sequencing. The 20 MHz clock supports fast sampling loops and display refresh alongside the metering algorithm, while the 64-pin through-hole package gives abundant port access for display and keypad lines. Its ROMless configuration lets the same controller serve metering and diagnostic firmware variants. Keep the display and keypad traces away from the external memory bus to avoid coupling when the bus toggles rapidly.
Inirekomenda
Legacy Equipment Retrofit and Repair
The Z86C9620PSC is a practical choice for keeping legacy Z80/Z8-based equipment in service, because the 64-pin DIP outline and through-hole leads match older boards that cannot accept surface-mount parts. At 20 MHz the controller reproduces original timing behaviour while offering a larger margin for modern diagnostic firmware stored in external memory. Because the part is ROMless, obsolete on-board EPROMs can be replaced with equivalent external devices. Verify the pin assignment against the manufacturer datasheet and confirm the external memory address map before energising the board.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for Z86C9620PSC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | Z86C9620VSC | Z86C9640PSC | Z86C9440PSC |
|---|---|---|---|---|
| Package | 64-pin SDIP, through-hole | 64-pin SDIP, through-hole - same footprint | 64-pin SDIP, through-hole - same footprint | 64-pin SDIP, through-hole - same footprint |
| Brand | Zilog | Zilog | Zilog | Zilog |
| CPU Core | Z8 8-bit CMOS core | Z8 8-bit CMOS core | Z8 8-bit CMOS core | Z8 8-bit CMOS core |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Program Memory Architecture | ROMless (external program memory) | ROMless (external program memory) | ROMless (external program memory) | ROMless (external program memory) |
| Terminal Form / Mounting | Through-hole | Through-hole | Through-hole | Through-hole |
| Number of Terminals | 64 | 64 | 64 | 64 |
| Peripheral / Timer Mix | Z8 timers, ports and serial resources per datasheet | Same Z8 peripheral set | Different peripheral allocation, same core | Different peripheral allocation, same core |
Pangunahing mga Pagkakaiba
- Same 64-pin SDIP footprint as the closest Zilog alternatives, enabling true board reuse (kumpara saZ86C9620VSC)
- ROMless architecture lets firmware density scale independently of the MCU (kumpara saZ86C9640PSC)
- Through-hole 64-pin construction keeps legacy and cost-sensitive boards manufacturable (kumpara saZ86C9440PSC)
Talaan ng Disenyo
Estimated layout guidance: because the Z86C9620PSC is ROMless, the external memory address and data bus occupies a large share of the 64 pins. Route these nets as a short, continuous path between the MCU and the memory device, keep the memory decoupling capacitor within a few millimetres of the memory supply pins, and avoid splitting the bus across a plane change. Place the oscillator crystal close to the clock pins with its load capacitor directly adjacent, since long clock traces on a through-hole board pick up noise that appears directly as timing jitter at 20 MHz.
Estimated power consideration: with a 5 V-class supply at a 20 MHz clock, the Z8 core plus external bus activity typically consumes on the order of tens of milliwatts, so supply regulation requirements are modest, but the external memory and any I/O loads add to the total. Confirm the actual operating current and supply tolerance range from the manufacturer datasheet before fixing the regulator, and place a bulk capacitor plus a 100 nF ceramic at the controller supply pins and a separate local capacitor at the memory device.
Two mistakes dominate Z8 ROMless designs. First, assuming the controller boots from internal memory - without external program memory fitted, the bus floats and the device will not run, so always populate the memory and verify its address range matches the firmware map. Second, ignoring the wait-state requirement when the external memory is slower than the 20 MHz CPU; the bus must be stretched or the memory must be fast enough, otherwise intermittent read errors appear. Also confirm unused input pins are tied to defined levels for deterministic reset and brown-out behaviour.
Impormasyon ng Pagsunod sa Kautusan
No explicit RoHS, REACH, lead-free, halogen-free or conflict-minerals statement appears in the manufacturer or distributor listings for this part, so these fields are left unknown. The device is a commercial-grade through-hole CMOS controller and is not presented as an automotive-qualified part.