Yükselteç IC'leri
Ürünler (1.100+)
INA122U - 36V Micropower Instrumentation Amplifier | TI
The Texas Instruments INA122U is a precision, low-power instrumentation amplifier with a 2.2 V to 36 V supply range, 60 µA typical quiescent current, and an 8-pin SOIC package. Designed for differential signal acquisition, it uses a two-op-amp architecture to provide accurate amplification of low-level sensor signals while operating from either a single supply or dual supplies. The device is suitable for portable medical instrumentation, data acquisition systems, industrial sensing, and low-power measurement equipment. What is an instrumentation amplifier? An instrumentation amplifier is a differential amplifier optimized for measuring a small voltage difference between two inputs while rejecting common-mode interference. In the signal-chain hierarchy, an instrumentation amplifier sits between a sensor and a higher-level processing circuit; it provides gain, input impedance, and common-mode rejection in one dedicated analog block. Unlike a general-purpose operational amplifier, an instrumentation amplifier is intended for differential sensing and often preserves signal integrity when large common-mode voltages are present. Key features of the INA122U include a low quiescent current of 60 µA, wide supply operation from 2.2 V to 36 V, a common-mode range extending to (V−) − 0.1 V, rail-to-rail output swing, low offset voltage of 250 µV maximum, low offset drift of 3 µV/°C maximum, and low noise. The 8-SOIC package supports conventional surface-mount assembly and is identified by DigiKey as a one-circuit instrumentation amplifier. The two-op-amp architecture provides a straightforward gain-setting network while keeping the device suitable for portable and low-power systems. The INA122U is designed for accurate, low-noise differential signal acquisition rather than high-speed waveform processing. Its supply flexibility allows operation from a compact single supply or from dual supplies up to ±18 V, depending on the application requirements. The low 60 µA quiescent current helps limit battery drain when the amplifier is part of a portable instrument. Typical applications include low-level sensor front ends, portable medical monitoring, strain and pressure measurement, battery-powered data acquisition, current sensing, and industrial process instrumentation. The device is particularly useful when a small differential signal must be amplified before conversion by an ADC. In these systems, the engineer should verify the selected gain against the input range, common-mode voltage, output swing, supply voltage, and settling requirements. The main design consideration is ensuring that the input and output signals remain within the device's electrical limits while the external gain network is selected correctly. Input filtering, proper grounding, stable reference connections, and PCB trace symmetry help preserve differential accuracy. The INA122U combines low power, flexible supply operation, and precision-oriented specifications in a compact package for portable and measurement applications. This page summarizes the verified manufacturer information, distributor listing, practical application guidance, and available comparison context for engineers evaluating INA122U. Because detailed gain-current, noise-density, bandwidth, and package-temperature data are not all present in the supplied source material, those values should be confirmed against the current Texas Instruments datasheet before final design release.
INA122UA - 36V Micropower Instrumentation Amplifier | Texas Instruments
The Texas Instruments INA122UA is a single-supply, micropower precision instrumentation amplifier rated for supply voltages from 2.2 V to 36 V, featuring a 60 uA quiescent current, a bandwidth of 120 kHz, and an 8-pin SOIC package. Designed for differential signal acquisition, it provides low offset voltage and low offset drift while consuming minimal power. The device can operate from either a single positive supply or a dual supply, making it suitable for portable medical equipment, battery-powered instruments, and distributed data-acquisition systems. An instrumentation amplifier is a specialized analog signal-conditioning amplifier that measures the voltage difference between two inputs. Its internal differential architecture rejects common-mode interference, while programmable gain amplifies weak sensor signals before they reach an ADC. Within the broader hierarchy, the INA122UA is an instrumentation amplifier, analog amplifier, signal-conditioning IC, and power-management-compatible analog semiconductor designed for low-voltage precision acquisition. Key features include a 60 uA typical quiescent current, a wide single-supply operating range extending to 36 V, and operation from dual supplies up to plus or minus 18 V. The input common-mode range can extend approximately 0.1 V below the negative supply, and the output supports rail-to-rail swing. Maximum offset voltage is 250 uV, while maximum offset drift is 3 uV per degree Celsius, supporting stable measurements where sensor baselines change with temperature. The INA122UA uses a two-op-amp instrumentation-amplifier architecture to provide accurate, low-noise differential acquisition. Its gain is established by an external resistor, allowing the signal chain to be scaled without sacrificing input impedance or common-mode rejection. The 120 kHz bandwidth supports low-frequency industrial, biomedical, and instrumentation signals, but it is not intended for high-speed signal capture. Exact gain limits, noise density, input impedance, and common-mode rejection values require confirmation in the manufacturer datasheet. Typical applications include portable ECG and physiological-signal front ends, industrial pressure and temperature sensors, low-current transducers, laboratory measurement systems, and battery-operated data loggers. In each case, the device combines a broad supply range with low quiescent current, helping preserve battery life while accepting sensor outputs that require common-mode rejection. A key design consideration is the interaction between common-mode range, output swing, gain, and supply voltage. The input and output operating regions must remain valid during startup, sensor faults, and maximum signal excursions. Input filtering, source impedance balancing, and careful grounding are also important when offset and noise-sensitive measurements are required. This page consolidates the verified manufacturer and distributor information for the INA122UA with package guidance, pricing availability notes, application analysis, and carefully qualified replacement considerations. Because the supplied records do not include complete numerical pricing or a complete pin map, those details are identified as unavailable rather than inferred.
INA125P - Precision Bridge Amplifier with 10V Reference | Texas Instruments
The Texas Instruments INA125P is a low-power, high-accuracy instrumentation amplifier with a built-in precision voltage reference, maximum input offset voltage of 250 µV, slew rate of 0.02 V/µs, bandwidth of 150 kHz, and a 16-pin plastic through-hole DIP package. It provides differential bridge amplification and excitation from one integrated circuit. An instrumentation amplifier is a precision analog amplifier optimized for measuring small differential signals while rejecting large common-mode voltages. In the signal-chain hierarchy, the INA125P belongs to the instrumentation-amplifier class, then analog signal-conditioning amplifiers, then amplifiers and integrated analog ICs. Its internal three-op-amp-style signal conditioning is particularly useful for resistive sensors whose outputs are small, differential, and referenced to a bridge supply. Key features include a low 460 µA typical quiescent current, a 10 V precision reference, sleep-mode shutdown, low input bias current, and an industrial temperature range of -40°C to +85°C. The integrated reference can excite a bridge directly, while the differential amplifier rejects common-mode voltage present on both sensor inputs. Sleep mode supports duty-cycle operation and can reduce supply demand when measurements are not continuously required. The verified distributor data identifies a 2.7 V to 36 V supply capability, while another distributor result describes operation from 1.35 V to ±18 V. The manufacturer describes the device as usable in single-supply or dual-supply arrangements, subject to the detailed datasheet limits. The 150 kHz bandwidth and 0.02 V/µs slew rate support low-to-moderate-frequency measurements where fast settling is less important than low offset and low power. Typical uses include load-cell signal conditioning, strain-gauge bridge measurements, pressure-transducer interfaces, industrial weighing systems, and portable sensor instrumentation. The internal 10 V reference is particularly valuable when the sensing bridge needs excitation and a compact analog front end is preferred. When designing around the INA125P, check the selected gain, reference configuration, supply voltage, input common-mode range, and output swing against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and the sensor return should be connected with care to preserve differential accuracy. The 16-pin DIP package is through-hole and is not mechanically interchangeable with the SO-16 variant. This page consolidates verified manufacturer and distributor information, package distinctions, application guidance, pricing context, and replacement-search results. It distinguishes confirmed drop-in evidence from unavailable alternatives rather than presenting unverified substitutions.
INA125PA - 10V Reference Bridge Amplifier | Texas Instruments
The Texas Instruments INA125PA is a single-channel instrumentation amplifier with an integrated 10 V precision voltage reference, differential input amplification, and bridge-excitation capability in a 16-pin PDIP package. It supports externally selected gains from 4 to 10,000, operates from 1.35 V to 18 V, and provides a typical bandwidth of 150 kHz. The device is designed for low-power measurement systems requiring accurate amplification of small differential signals. An instrumentation amplifier is a specialized amplifier IC that converts a low-level differential signal into a single-ended or differential output. Its internal architecture rejects common-mode noise while amplifying the voltage difference between two inputs. In the power-management and signal-chain hierarchy, an instrumentation amplifier is an amplifier IC used for sensor-interface, bridge-measurement, and precision signal-conditioning applications. The INA125 adds an internal voltage reference capable of exciting resistive sensor bridges. The INA125PA provides a low quiescent current of 460 µA, a maximum low-frequency offset voltage of 250 µV, and maximum offset drift of 2 µV/°C. Its precision voltage reference is fixed at 10 V. A single external resistor sets the gain, allowing gains from 4 to 10,000 while avoiding the need for a resistor network. Low offset, low drift, and low power consumption make the device useful for battery-powered and precision industrial equipment. Internally, the amplifier combines a precision gain stage with an integrated reference and low-noise input network. The high gain range supports resistive bridges with relatively small differential outputs, while the 150 kHz bandwidth covers many temperature, pressure, force, and position sensing applications. Because this is athrough-hole PDIP device rather than a surface-mount package, it is especially convenient for prototype boards, educational instruments, legacy industrial controls, and repair assemblies. Typical uses include Wheatstone bridge excitation and measurement, load-cell signal conditioning, industrial pressure transducers, portable measurement instruments, and low-power sensor interfaces. The 10 V reference can bridge suitable high-impedance resistive networks, but the bridge and input network must remain within the device's supply, common-mode, and electrical limits. The broad gain range also permits direct measurement of small millivolt-level signals without a separate front-end amplifier. Designers should place the gain-setting resistor close to the gain resistor pins and use a stable, low-temperature-coefficient resistor when gain accuracy matters. Input filtering should preserve the required bandwidth, while supply bypassing should use short, low-inductance connections. Because the INA125PA includes a precision reference, designers must account for reference current loading when the 10 V output is used to power external circuitry. This page consolidates verified manufacturer and distributor information, explicit data gaps, practical design guidance, and a careful same-package replacement assessment. The supplied sources establish the INA125PA's core functionality but do not provide five verified pin-to-pin alternatives, so the replacement list is intentionally limited rather than padded with electrically different or differently packaged parts.
INA125U - Precision Bridge Amplifier, 10V Ref | Texas Instruments
The Texas Instruments INA125U is a low-power, high-accuracy instrumentation amplifier with a precision 10V voltage reference, user-selectable gain from 4 to 10,000, and a 16-pin SOIC package. It combines bridge excitation and differential-input amplification on one integrated circuit, making it suitable for strain-gauge, pressure-transducer, and other bridge-sensor signal chains. An instrumentation amplifier is a specialized differential amplifier designed for sensors whose useful output is small and appears across two input terminals. Its internal architecture provides high input impedance, accurate differential gain, and strong common-mode rejection. The INA125 adds a precision reference output, allowing a bridge circuit to be excited and its output measured relative to a stable midpoint. The INA125U offers a 2.7V to 36V supply range, low 460µA quiescent current, maximum 250µV input offset voltage, maximum 2µV/°C offset drift, and a sleep mode. A single external resistor sets the gain, while the integrated amplifier can provide 150kHz bandwidth according to the retrieved product data. These features balance precision, power consumption, and measurement speed for portable and industrial instrumentation. Electrically, the device is intended for bridge outputs and other low-level differential sources. Input common-mode range, reference accuracy, gain error, and maximum input voltage must be checked against the actual bridge excitation and sensor output. The SOIC package also requires careful attention to ground return paths and supply decoupling when low-level signals are measured. Typical uses include quarter-bridge and full-bridge strain sensors, load-cell front ends, pressure and force measurement, biomedical instrumentation, industrial process controls, and precision data-acquisition systems. The 10V reference can simplify excitation when the sensor and measurement chain require a defined bridge supply. The most important design consideration is preserving common-mode and differential signal integrity. Place input and reference grounding deliberately, use low-noise supply bypass capacitors, and verify that the selected gain resistor stays within its recommended range. This page combines verified manufacturer and distributor information with practical application guidance and explicit data gaps rather than estimating unprovided specifications.
INA126P - 36V MicroPower Precision INA | Texas Instruments
The Texas Instruments INA126P is a precision micropower instrumentation amplifier rated for a 36 V maximum supply, with 175 µA quiescent current, 250 µV input offset voltage, and gain values set by an external resistor. It is supplied in an 8-pin PDIP package for through-hole industrial, portable, and measurement-instrumentation designs. An instrumentation amplifier is a differential analog-front-end IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. INA126 belongs to the instrumentation-amplifier hierarchy within operational amplifiers and analog signal-chain ICs. Its two-op-amp architecture supports accurate, low-noise acquisition from sensors, bridges, and low-level transducers, especially where power consumption and input precision are important. The verified features include 250 µV offset, 175 µA typical quiescent current, and operation from ±1.35 V to ±18 V, corresponding to a stated 36 V maximum supply condition. The INA126 family also provides programmable gains of 1, 10, 100, or 1000 through the external gain resistor. These values make it suitable for battery-powered instrumentation, industrial measurement, portable diagnostics, and sensor interfaces where common-mode rejection and low bias current are more valuable than wide bandwidth. The device uses a two-op-amp internal architecture rather than a three-op-amp topology, helping keep power consumption low. Because the gain depends on the external resistor and its matching, PCB resistor placement, source impedance balance, input filtering, grounding, and reference-connection practices directly influence accuracy. The 8-pin PDIP package is mechanically straightforward for through-hole assembly but requires adequate lead spacing and clean soldering practice. Typical applications include bridge-based pressure and load measurement, low-level sensor conditioning, portable medical or industrial instrumentation, battery-operated data acquisition, and differential signal acquisition where a precision offset and low supply current are required. For single-supply systems, the output-reference arrangement must be designed to keep the output within the input and output common-mode limits. The principal design trade-off is the relatively modest micropower-focused feature set versus higher-bandwidth or lower-noise instrumentation amplifiers. Confirm supply voltage, input range, gain resistor, output swing, reference connection, and common-mode limits against the manufacturer datasheet before committing a PCB design. This page combines verified manufacturer and distributor information with design guidance, selection criteria, and same-package comparison context for engineers evaluating the INA126P.
INA126PA - 36V Micropower Instrumentation Amplifier | TI
The Texas Instruments INA126PA is a single-channel, precision micropower instrumentation amplifier with a 36 V maximum supply rating, 250 µV input offset voltage, 175 µA quiescent current per channel, and an 8-pin PDIP package. It is designed to acquire accurate, low-noise differential signals while consuming very little power. The two-operating-amplifier architecture supports common-mode rejection and differential signal conditioning in compact, portable, and industrial instrumentation systems. An instrumentation amplifier is a specialized amplifier category used to amplify the difference between two input signals while rejecting common-mode voltage. Within the amplifier hierarchy, an instrumentation amplifier is a precision analog amplifier, while an operational amplifier is a more general-purpose building block. The INA126PA belongs to the micro-power instrumentation-amplifier family and combines differential input measurement, adjustable gain, and low bias current in one integrated circuit. The principal advantages are low power consumption, low offset voltage, a wide operating-supply range of ±1.35 V to ±18 V, and operation from a single supply down to 2.7 V. According to the manufacturer datasheet, the device uses 175 µA per channel and provides a gain adjustment range of 1 V/V to 1000 V/V. These characteristics suit battery-powered and portable measurement systems where amplifier power can materially affect available operating time. The INA126PA uses a two-operating-amplifier architecture for accurate, low-noise differential-signal acquisition. Its instrumentation-amplifier function is useful when the wanted signal is smaller than the voltage shared by both input nodes. The low 175 µA quiescent current is particularly important in portable instrumentation and data-acquisition systems, while the 250 µV offset specification supports precision measurement of small differential voltages. Typical applications include portable sensor acquisition, industrial process measurement, battery-operated diagnostic equipment, low-current transducers, and differential voltage sensing. In each case, the device can condition a low-level differential input before it reaches an ADC or another signal-processing stage. Its single- and dual-supply flexibility allows it to be used with compact analog systems operating from low-voltage sources as well as higher-voltage industrial rails. Designers should verify the exact gain-setting resistor against the manufacturer gain table and preserve the input and reference-pin arrangements shown in the datasheet. The reference input should be connected to a defined low-impedance voltage, and unused inputs must not be allowed to float. PCB layout should keep the gain-setting resistor close to the device to minimize added noise and instability in sensitive measurement circuits. This product page consolidates verified manufacturer and distributor information, lifecycle guidance, package details, replacement analysis, and practical design guidance. It also distinguishes verified drop-in candidates from changes requiring a different package, helping engineers avoid confusing functional equivalence with literal PCB-level replaceability.
INA126U - 36V Micropower Instrumentation Amp | Texas Instruments
The Texas Instruments INA126U is a single-circuit micropower precision instrumentation amplifier rated for a 36 V total supply, with 175 µA quiescent current per channel, 250 µV offset, and an 8-pin SOIC package. Its differential-input architecture supports accurate, low-noise signal acquisition where common-mode interference, source impedance mismatch, and power consumption must all be controlled. An instrumentation amplifier is a specialized amplifier and the final member of the signal-chain hierarchy: sensor output → differential input → instrumentation amplifier → ADC or measurement system. Unlike a general-purpose operational amplifier, an instrumentation amplifier internally supports high input impedance and accurate differential gain, reducing errors when both inputs originate from balanced sensors, resistive bridges, or shunt measurements. The INA126 family uses a two-op-amp architecture optimized for precision and micropower operation. Verified headline features include a 36 V maximum supply, 175 µA per-channel quiescent current, and 250 µV offset. The manufacturer describes the device for accurate, low-noise differential-signal acquisition across a wide operating voltage range of ±1.35 V to ±18 V. These properties suit portable instruments and low-power acquisition systems where battery energy is limited but input-referred accuracy remains important. The single amplifier in the INA126U also avoids the extra power and board area associated with an unnecessary dual channel. The INA126U can be configured through an external gain-setting resistor. Because its instrumentation-amplifier architecture rejects common-mode signals before they reach the output, it is particularly useful when the wanted differential signal is much smaller than the voltage shared by both inputs. Designers must still verify input and output common-mode limits, maximum differential input voltage, gain-bandwidth behavior, resistor tolerance, output swing, and the sensor output range for the intended supply voltage. Precision performance ultimately depends on resistor matching and careful grounding as well as the amplifier itself. Typical uses include battery-powered sensor interfaces, portable measurement instruments, current-shunt amplifiers, bridge-signal conditioning, and low-power data-acquisition front ends. The 175 µA per-channel quiescent current is particularly useful where idle current directly affects battery life. The 250 µV offset specification gives designers a defined input-referred error reference, while the 36 V supply capability supports higher-voltage industrial systems when the individual input and output ranges are observed. For PCB implementation, keep the external gain resistor close to the gain-setting pins, use a stable low-noise reference plane, and place input-protection capacitance only after checking its effect on bandwidth and transient response. Avoid long parallel input traces, maintain symmetric routing where practical, and provide local supply bypassing. Verify common-mode headroom at worst-case sensor voltage and load current rather than relying only on nominal supply conditions. This page combines verified manufacturer facts, distributor pricing, same-package alternatives, and application-oriented design guidance. It also distinguishes documented values from parameters requiring confirmation from the complete manufacturer datasheet, helping engineers move from component selection to a defensible low-power sensor-board design.
INA128P - 130dB CMRR Precision INA | Texas Instruments
The Texas Instruments INA128P is a precision, low-power instrumentation amplifier with 130 dB CMRR, a 700 µA quiescent current, and an 8-pin PDIP package. It provides 50 µV maximum offset voltage, 0.5 µV/°C maximum offset drift, 5 nA maximum input bias current, and 1.3 MHz bandwidth. The device accepts supply voltages from ±2.25 V to ±18 V and supports input protection to ±40 V. An instrumentation amplifier is a specialized amplifier-IC category designed to amplify small differential sensor signals while rejecting common-mode interference. INA128P belongs to the instrumentation-amplifier hierarchy, which also includes differential amplifiers and analog front ends for measurement systems. Its three-op-amp architecture provides accurate differential gain, high input impedance, and flexible gain selection with an external resistor. Key features include a low offset voltage of 50 µV maximum and low offset drift of 0.5 µV/°C maximum. The 130 dB CMRR figure minimizes errors when a sensor signal is small relative to its common-mode voltage. Current-feedback input circuitry preserves bandwidth at higher gain, including 200 kHz bandwidth at a gain of 100. Input bias current remains low at 5 nA maximum, which is valuable for high-impedance sensors. The INA128P uses a versatile three-op-amp instrumentation-amplifier architecture and is available in an 8-pin plastic DIP package. Its ±2.25 V to ±18 V supply range supports dual-supply analog systems and higher-voltage industrial interfaces. The specified operating temperature range is -40 °C to +85 °C. The low 700 µA quiescent current helps reduce power consumption in portable and low-power measurement equipment. Typical applications include bridge and strain-gauge signal conditioning, current measurement, biomedical instrumentation, industrial sensor interfaces, precision data acquisition, and laboratory measurement systems. The device is particularly suitable when common-mode rejection and low offset are more important than very high bandwidth. The manufacturer datasheet also identifies current-feedback input circuitry for improved high-gain bandwidth. When designing around INA128P, choose the external gain resistor carefully because it determines gain accuracy and stability. Keep input and feedback routing compact, observe the specified supply limits, and verify common-mode voltage, input protection, and output-swing requirements against the actual sensor and measurement chain. The INA128P is not a power semiconductor, so safe-operating-area data is not applicable. This page combines verified manufacturer specifications, distributor availability information, cross-reference results, and practical design guidance for engineers evaluating precision sensor-signal conditioning.
INA128PA - 130dB CMRR Low-Power INA | Texas Instruments
The Texas Instruments INA128PA is a precision, low-power instrumentation amplifier with 130 dB CMRR, 700 µA quiescent current, and an 8-pin PDIP package. It uses a versatile three-op-amp architecture to amplify small differential signals while rejecting common-mode interference. Its specified low offset voltage, low drift, low bias current, wide supply range, and protected inputs make it suitable for precision measurement systems. The device supports gains from 1 through 10,000 using one external gain-setting resistor and retains useful bandwidth at high gain. An instrumentation amplifier is a specialized analog amplifier optimized for measuring low-level differential signals in the presence of large common-mode voltages. Its internal three-op-amp arrangement provides high input impedance, accurate differential gain, and strong common-mode rejection without requiring matched external resistors. INA128PA belongs to the instrumentation-amplifier hierarchy, which sits within signal-conditioning and amplifier ICs used in instrumentation, industrial control, biomedical measurement, and test equipment. Verified features include a maximum input offset voltage of 50 µV, maximum input voltage drift of 0.5 µV/°C, maximum input bias current of 5 nA, minimum CMR of 120 dB, input protection to ±40 V, and a supply range up to ±18 V. The low quiescent current is 700 µA, making the device suitable for power-conscious precision analog systems. According to the verified TI product data, the INA128 family provides 200 kHz bandwidth at a gain of 100. The three-op-amp internal design uses current-feedback input circuitry to preserve bandwidth as gain increases. This architecture is important when the measured signal is small and the source impedance is not negligible: the low 5 nA maximum bias current reduces loading of high-resistance sensors. The 130 dB CMRR specification helps reject common-mode voltage produced by motor systems, mains-coupled noise, or long sensor cables. Typical uses include precision current sensing, bridge-transducer amplification, biomedical instrumentation, portable measurement, laboratory equipment, and industrial process monitoring. The part can operate from dual or single supplies as supported by the family documentation, but the exact operating modes and output-swing limits should be checked against the manufacturer datasheet before final design release. For PCB implementation, keep the gain resistor close to the gain-setting pins and use a quiet ground return for the signal path. Input filtering, common-mode voltage limits, output settling, and supply decoupling must be evaluated for the target gain and bandwidth. Do not assume that the protected input rating removes the need for external transient protection in every system. This page combines verified manufacturer and distributor information, package-specific identification, application guidance, and cautious replacement analysis. Values not explicitly verified in the supplied data remain marked for engineering review rather than estimated.
INA129A - Precision Instrumentation Amplifier | Texas Instruments
The Texas Instruments INA129A is a precision, low-power instrumentation amplifier packaged in an 8-pin SOIC. It offers excellent accuracy for general-purpose signal conditioning, with low offset voltage, low drift, low input bias current, high common-mode rejection, and input protection to ±40 V. Its versatile three-op-amp architecture supports externally set gains and current-feedback input circuitry that maintains wide bandwidth even at high gain, including 200 kHz at a gain of 100. An instrumentation amplifier is a specialized amplifier that amplifies the difference between two input signals while rejecting common-mode voltage and providing high input impedance. The INA129A belongs to the broader precision analog signal-conditioning hierarchy: instrumentation amplifier, differential amplifier, analog amplifier, and semiconductor. It is used where sensors, transducers, strain gauges, bridge circuits, and measurement front ends require accurate differential amplification with minimal disturbance to the source. The INA129 family is designed for low-power precision applications. A single external resistor sets the gain from 1 to 10,000, according to the manufacturer product information. The device provides a wide supply range of ±18 V, a minimum common-mode rejection of 120 dB, input bias current of 5 nA maximum, and input protection to ±40 V. Its current-feedback input stage is particularly useful in higher-gain designs because it preserves bandwidth better than a conventional voltage-feedback input arrangement. The INA129A can amplify low-level sensor signals in industrial measurement systems, bridge-based load cells, biomedical instrumentation, audio equipment, and data-acquisition systems. Its common-mode rejection helps suppress equal voltages appearing on both inputs, while high input impedance limits loading of the measured source. The ±40 V input protection provides additional robustness when connected to external wiring or larger transients, subject to the complete datasheet ratings and system design limits. When using INA129A, place the gain-setting resistor close to the appropriate gain pins and keep input and feedback traces short to reduce parasitic capacitance and noise pickup. Check supply decoupling, input common-mode range, output swing, and resistor tolerance before finalizing a design. Because the INA129A is a precision analog amplifier, grounding, shielding, clean references, and careful PCB layout can matter as much as nominal gain accuracy. This product page combines the verified INA129A electrical and physical details, manufacturer and distributor references, comparison parameters, and practical design guidance. The listed alternatives are limited to candidates supported by the supplied cross-reference data; package and pin compatibility should still be confirmed against the current manufacturer datasheet before substitution.
INA129P - Precision Low-Power 8-Pin Instrumentation Amp | TI
The Texas Instruments INA129P is a precision, low-power instrumentation amplifier with one amplifier circuit, 120 dB minimum common-mode rejection, 50 uV maximum offset voltage, and a 200 kHz bandwidth at gain 100, packaged in an 8-pin PDIP. It accepts signals within the low-noise, low-offset instrumentation-amplifier class and supports wide bipolar supply operation up to ±18 V. An instrumentation amplifier is a specialized analog amplifier that measures a small differential voltage while rejecting common-mode interference. Its internal three-op-amp architecture supports high input impedance and adjustable gain, making it useful when a sensor produces a low-level signal and the surrounding wiring introduces substantial common-mode voltage. The INA129P is therefore positioned between a general-purpose operational amplifier and a more specialized precision measurement amplifier. Key features include 50 uV maximum offset voltage, 0.5 uV/°C maximum offset drift, 5 nA maximum input bias current, and input protection to ±40 V. The single external gain-setting resistor provides gain adjustment from 1 through 10,000 according to the manufacturer family information, while current-feedback input circuitry maintains useful bandwidth at higher gain. The stated 200 kHz bandwidth at gain 100 makes the device suitable for sensor and instrumentation signal paths rather than only static measurement. The INA129P uses a low-power instrumentation-amplifier architecture intended for precision measurement systems. Its common-mode rejection helps suppress voltage common to both inputs, and the low offset and drift reduce measurement error in bridge, current, and industrial sensor applications. The ±18 V supply capability provides flexibility for dual-supply analog systems, while the 8-pin PDIP format supports through-hole assembly and prototyping. Typical uses include bridge and load-cell signal conditioning, industrial process measurement, biomedical instrumentation, current sensing, and precision test equipment. The ±40 V input protection specification is useful when the amplifier is positioned near sensor wiring, although system-level protection and operating conditions still require engineering review. The principal design consideration is ensuring that the external gain resistor, supply bypassing, input protection, and common-mode range are matched to the sensor. For a new design, verify the exact INA129P pinout and electrical limits against the current Texas Instruments datasheet before layout release. This page consolidates verified distributor snippets, manufacturer family information, package details, and application guidance, while distinguishing documented specifications from information that requires design-team verification.
INA129PA - Precision Low-Power Instrumentation Amplifier | TI
The Texas Instruments INA129PA is a precision, low-power instrumentation amplifier in an 8-pin plastic DIP package, with a maximum input offset voltage of 50 uV, maximum offset drift of 0.5 uV/degC, maximum input bias current of 5 nA, and minimum common-mode rejection of 120 dB. Its input stage tolerates voltages from -40 V to +40 V, while its supply range extends to plus or minus 18 V. These characteristics make it appropriate for precision signal conditioning where low offset, low drift, high common-mode rejection, and input protection are important. An instrumentation amplifier is a differential analog IC used to amplify the voltage difference between two inputs while rejecting signals common to both inputs. The INA129 belongs to the broader instrumentation-amplifier, amplifier-IC, and analog-semiconductor hierarchy. Its internal gain-setting arrangement supports precise amplification of small differential signals in sensor interfaces, industrial measurement systems, and laboratory equipment. The verified device features distinguish the INA129 from ordinary general-purpose operational amplifiers. A 50 uV maximum input offset voltage reduces the effect of input-referred mismatch, while the 0.5 uV/degC maximum drift limits offset variation with temperature. Maximum input bias current of 5 nA is especially relevant when the source impedance is high. Minimum CMRR of 120 dB suppresses common-mode interference, and the -40 V to +40 V input protection range helps the interface tolerate larger external voltages than the internal operating range. The INA129 supports a wide supply range of plus or minus 18 V. A wide operating range allows the amplifier to process signals within systems using higher-voltage rails while retaining the low-power characteristics highlighted for this device. Exact gain, bandwidth, quiescent-current, input-voltage, and output-voltage limits were not available in the supplied verified data and should be taken from the manufacturer datasheet before final design release. Typical uses include bridge-sensor interfaces, current-shunt measurement, precision data acquisition, industrial process monitoring, and low-level differential signal conditioning. For bridge or shunt circuits, the 120 dB minimum CMRR helps reject common-mode noise, while low offset voltage and drift reduce measurement error. The protected inputs may improve robustness when transients or nearby switching nodes can appear at the input terminals. Designers should verify the gain equation, external resistor value, permissible input and output swing, and supply-current limits against the current manufacturer datasheet. Input filtering, source-impedance balancing, grounding, and placement near the measured signal are also important because excessive imbalance can degrade CMRR and the low-offset performance expected from this precision device. This page combines verified manufacturer and distributor information with practical selection guidance, application analysis, pricing context, and verified drop-in alternatives. It distinguishes documented INA129PA characteristics from information that remains unavailable, helping engineers make a more reliable instrumentation-amplifier choice without inventing specifications.
INA129U - ±18V Precision Instrumentation Amp | Texas Instruments
The Texas Instruments INA129U is a precision, low-power instrumentation amplifier with a 1.3 MHz gain-bandwidth product, 120 dB minimum common-mode rejection, and an 8-pin SOIC package. It accepts single or dual supplies up to ±18 V and uses one external resistor to set gain from 1 through 10,000. Designed around a versatile three-op-amp architecture, the INA129U supports accurate differential measurement while preserving wide common-mode range and robust input protection. An instrumentation amplifier is a specialized amplifier category that measures the voltage difference between two inputs while rejecting signals common to both nodes. INA129U belongs to the hierarchy instrumentation amplifier, differential amplifier, analog signal-conditioning IC, and power-management-independent semiconductor. Its three-op-amp topology provides high input impedance, precise differential gain, and improved common-mode rejection compared with a simple difference amplifier. Key verified features include maximum offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, maximum input bias current of 5 nA, and differential input protection extending to ±40 V. The current-feedback input circuitry maintains useful bandwidth at higher closed-loop gains, including 200 kHz at a gain of 100. These characteristics make the device useful where small transducer outputs must be amplified accurately in the presence of a larger common-mode voltage. The INA129 gain equation uses a 49.4 kΩ external resistor to support drop-in replacement with comparable instrumentation amplifiers. Gain accuracy depends on that resistor and associated layout parasitics, so designers should follow the manufacturer gain-setting guidance and preserve a symmetric input path. Low bias current is especially valuable for high-impedance sensor sources, while high CMR suppresses supply and ground disturbances that appear equally on both inputs. Typical uses include bridge-transducer signal conditioning, isolated low-voltage sensing, current-shunt measurement, biomedical acquisition, industrial sensor interfaces, laboratory instrumentation, and portable diagnostic equipment. For these applications, the ±40 V protected inputs can reduce accidental overload risk, although external protection and supply limits still require validation. The principal design consideration is keeping both input paths symmetric and placing the gain resistor close to the device. Incorrect Kelvin routing or unequal input impedance can degrade CMR and offset performance. The 8-pin SOIC also makes PCB assembly straightforward, while exposed thermal behavior and supply noise still require normal analog-layout practices. This page consolidates verified manufacturer and distributor information, package details, purchasing context, applications, and replacement guidance. It also distinguishes explicitly supported drop-in candidates from parts that require engineering review, helping designers compare the INA129U with alternatives rather than treating them as automatic equivalents.
INA129U/2K5 - Precision Low Power INA, SOIC-8 | Texas Instruments
The Texas Instruments INA129U/2K5 is a precision, low-power instrumentation amplifier (INA) in an 8-pin SOIC surface-mount package, supplied on a 2,500-piece tape-and-reel. The INA129 family uses a classic three-op-amp topology with current-feedback input stages, delivering 50 µV maximum offset voltage, 0.5 µV/°C maximum drift, 5 nA maximum input bias current, and a minimum common-mode rejection ratio (CMRR) of 120 dB at G = 100. A single external resistor sets any gain from 1 V/V to 10,000 V/V. The /2K5 suffix indicates the SO-8 packaging option on a 2.5k reel per TI's ordering nomenclature. An instrumentation amplifier is a precision differential amplifier with very high input impedance on both inputs, a defined and stable gain set by one external resistor, and exceptionally high common-mode rejection. The INA belongs to the family of analog front-end ICs that sit between a sensor (bridge, thermocouple, biopotential electrode) and an ADC. The category hierarchy is: instrumentation amplifier -> differential amplifier -> operational amplifier -> analog IC -> semiconductor. The three-op-amp topology isolates the input signal from the gain-setting resistor network, allowing tiny differential signals (often microvolts) to be amplified cleanly in noisy industrial environments. Key features of the INA129U/2K5 include wideband operation up to 1.3 MHz (G = 1) with 200 kHz bandwidth even at G = 100, a 4 V/µs slew rate, ±2.25 V to ±18 V dual-supply operation (±2.25 V minimum; typically ±15 V in transducer systems), input protection to ±40 V, and a quiescent current of only 700 µA typical. The exposed SO-8 package simplifies reflow assembly on standard 8-pin SOIC land patterns identical to the INA128, AD620, and other pin-compatible INAs. The current-feedback input stage keeps bandwidth flat across the full gain range, an advantage over voltage-feedback INAs that lose bandwidth at high gain. The INA129's gain equation G = 1 + 49.4kΩ/RG matches the AD620, allowing direct drop-in migration from legacy designs. The combination of low noise, low drift, and high CMRR makes the INA129U/2K5 well-suited for strain-gauge bridges, weigh scales, thermocouple amplifiers, medical instrumentation (ECG/EEG front-ends), and industrial process-control analog inputs. Typical applications include weigh scales and load-cell signal conditioning, ECG and biomedical front-ends, thermocouple and RTD pre-amplification, and industrial 4-20 mA loop readouts. Place the gain-setting resistor close to pins 1 and 8, and use 0.1 µF ceramic bypass capacitors on both supply pins to preserve the 120 dB CMRR across frequency. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
INA131AP - Precision G=100 Instrumentation Amp | Texas Instruments
Texas Instruments INA131AP is a precision, fixed-gain instrumentation amplifier with a gain of 100, a 70 kHz bandwidth, a 106 dB common-mode rejection ratio, and a 125 µV maximum input offset voltage. The device is supplied in an 8-pin PDIP package and operates from ±2.25 V to ±18 V. Its 3-op-amp architecture supports accurate differential signal conditioning, including low-level sensor measurements where common-mode interference must be rejected. An instrumentation amplifier is a specialized analog amplifier optimized for amplifying the difference between two input signals while rejecting voltage common to both inputs. Within the signal-conditioning hierarchy, an instrumentation amplifier is a precision analog IC used for current sensing, bridge excitation, biomedical instrumentation, and industrial measurement. Its internal differential input and feedback arrangement generally provides better common-mode rejection and offset behavior than a conventional op-amp circuit configured for the same function. The INA131AP provides a fixed gain of 100, allowing small differential sensor outputs to be raised to a level suitable for an ADC without an external gain-setting network. Maximum input offset voltage is 125 µV, while input bias current is specified at no more than 2 nA. Input overvoltage protection extends to ±40 V, helping the amplifier tolerate transient voltage at sensor inputs. The listed operating range of ±2.25 V to ±18 V supports dual-supply operation across common industrial and instrumentation systems. Internally, the INA131 uses a three-op-amp instrumentation-amplifier architecture. This arrangement provides high input impedance, differential gain of 100, and strong rejection of common-mode signals. The listed 106 dB CMRR is particularly useful when the measured differential signal is much smaller than the voltage shared by both input terminals. A slew rate of 0.7 V/µs and bandwidth of 70 kHz define its response for low-frequency industrial, measurement, and control signals. Typical uses include precision current sensing, bridge-based pressure and strain measurement, low-level differential sensor interfaces, analog signal conditioning, and buffered measurement channels. The fixed gain also simplifies system calibration because engineers do not need to select or adjust an external precision gain resistor. The 8-pin PDIP package is particularly useful for prototypes, laboratory equipment, legacy industrial systems, and designs assembled through through-hole manufacturing processes. Designers should preserve the input common-mode range and supply headroom for the selected output voltage. Because the gain is fixed at 100, input signals must remain small enough to prevent saturation, while source impedance and sensor grounding can influence offset and bias-current error. The INA131AP is non-isolated and operates from a bipolar supply, so system power architecture, grounding, transient protection, and input filtering should be reviewed before deployment. This product page consolidates the verified distributor data, manufacturer resources, package information, procurement details, and engineering guidance for the INA131AP. It also distinguishes verified drop-in candidates from cross-reference search results, helping engineers evaluate PCB compatibility and device-level limitations rather than relying only on the “instrumentation amplifier” device category.
INA132U - Low-Power Unity-Gain Diff Amp | TI | 8-SOIC
The Texas Instruments INA132U is a low-power, unity-gain difference amplifier consisting of a precision op amp with an on-chip precision resistor network, housed in an 8-pin SOIC package. It operates from a single supply of 2.7V to 36V (or dual ±1.35V to ±18V), draws only 75 µA quiescent current, and offers 300 kHz small-signal bandwidth with a 1 MHz unity-gain op-amp stage. A difference amplifier is an op-amp-based circuit that amplifies the voltage difference between two inputs while rejecting signals common to both (the common-mode voltage). It is a foundational building block in signal-chain electronics, classified under instrumentation amplifiers and differential interfaces. Within the broader taxonomy, the INA132U sits at: difference amplifier -> instrumentation amplifier -> operational amplifier -> amplifier IC -> analog semiconductor. On-chip laser-trimmed resistors set the gain at exactly unity (G = 1), so no external precision network is required, simplifying PCB layout and BOM cost in measurement and sensor-conditioning applications. Key features include 250 µV typical offset voltage, a 60 V/µs equivalent slew rate at the op-amp core, and a quiescent current of 160 µA maximum over temperature. The internal op-amp common-mode range extends to the negative supply rail, enabling true single-supply operation from ground-referenced or low-side-shifted signals. Excellent TCR (temperature coefficient of resistance) tracking of the thin-film resistors maintains both gain accuracy and common-mode rejection across the -40°C to +85°C industrial range. The architecture uses a precision bipolar input stage followed by a fixed-gain thin-film resistor network and a unity-gain output buffer. CMRR exceeds 80 dB at DC for matched input impedances, and the integrated resistor matching eliminates the gain error and trimming burden typically associated with discrete difference amplifiers built from precision 0.1% resistors and a four-op-amp instrumentation topology. Typical applications include bridge transducer signal conditioning (load cells, strain gauges), ground-loop elimination in long-cable runs, differential signal reception in industrial process control, ECG/biopotential front-ends, and audio balanced-line receivers. Designers also use the INA132U as a building block inside higher-order active filters and as a differential-to-single-ended converter for ADC inputs. When designing with this part, observe the absolute maximum supply of 36V (single) or ±18V (dual) and ensure input common-mode voltage stays within the input range of each input pin, not just the differential value. A 0.1 µF supply decoupling capacitor placed within 5 mm of the V+ pin is recommended. The integrated gain is fixed at 1, so external attenuation or pre-gain stages are needed when the source signal is smaller than the ADC full scale. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet.
INA133U - 1.5MHz Precision Difference Amplifier | TI
The Texas Instruments INA133U is a 1.5 MHz, precision unity-gain difference amplifier with up to 450 µV offset, 0.95 mA typical power-supply current, and an 8-pin SOIC package. Designed for low-level differential measurement, it combines a precision operational amplifier with a laser-trimmed resistor network for accurate gain and common-mode rejection. The device is offered in the INA133U package configuration identified by DigiKey as an 8-SOIC differential amplifier. A difference amplifier is a specialized analog amplifier that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. This function is useful when a sensor, transducer, or measurement node is exposed to large common-mode voltages and the desired information exists only as a small differential signal. In the broader hierarchy, the INA133U belongs to instrumentation and difference amplifiers, within operational amplifiers and analog signal-conditioning ICs. The INA133U combines 1.5 MHz bandwidth with low offset voltage and low power consumption. Its high-speed behavior makes it suitable for current-shunt monitoring, bridge excitation, differential sensing, and industrial signal-conditioning systems. The on-chip laser-trimmed resistors are designed to improve gain accuracy and common-mode rejection, while their temperature-coefficient tracking helps preserve performance across temperature changes. The precision architecture is important because it combines amplifier bandwidth with accurate differential gain. A difference amplifier can reject shared interference, but its usefulness still depends on common-mode voltage staying within the device operating limits and on the surrounding circuit presenting suitable impedance and filtering. Designers should verify the complete input, output, supply, and common-mode conditions from the manufacturer datasheet. Typical applications include high-side current measurement, differential voltage sensing, bridge-based sensor interfaces, amplifier-input protection networks, and industrial control systems. In a shunt monitor, the INA133U can amplify the voltage across a low-ohm resistor while reducing the effect of supply or ground disturbances. In bridge sensing, it helps convert a small differential sensor output while rejecting common-mode excitation voltage. The principal design trade-off is bandwidth versus precision and power. The 1.5 MHz bandwidth supports faster signal changes than a purely low-bandwidth precision amplifier, while the 0.95 mA power figure favors low-power systems. PCB layout should keep input traces short, use a solid ground reference, and provide stable supply bypassing. This page synthesizes the verified manufacturer and distributor information, practical design considerations, and carefully limited replacement guidance.
INA133UA - 1.5 MHz Precision Difference Amplifier | Texas Instruments
Texas Instruments INA133UA is a precision difference amplifier with 1.5 MHz bandwidth, 450 uV maximum offset voltage, and 0.95 mA power consumption. The device is packaged in an 8-pin SOIC surface-mount package and is designed for high-speed signal-chain applications where a differential input must be amplified accurately. According to the Texas Instruments INA133 product information, the INA133 family uses a unity-gain configuration and provides high gain accuracy and common-mode rejection ratio. The verified product listing identifies the INA133UA as a differential amplifier in an 8-SOIC package, while the INA133UA/2K5 ordering variant is also listed in an 8-pin SOIC package. A difference amplifier is an operational-amplifier-based circuit that responds to the voltage difference between two input terminals rather than to either input voltage independently. This makes the INA133UA suitable for current-sense, bridge-sensor, instrumentation, and high-speed measurement circuits where common-mode voltage can be substantially larger than the wanted differential signal. The 1.5 MHz bandwidth provides a useful compromise between response speed and precision, while the specified 450 uV offset and 0.05% maximum gain error help establish the accuracy of the amplified result. The INA133UA operates with single or dual power supplies according to the manufacturer family information. Its 0.95 mA power consumption is suitable for compact, low-power signal-conditioning equipment when compared with general-purpose implementations that consume more current. The 8-pin SOIC package permits conventional surface-mount assembly and provides a straightforward footprint for designs that require one precision differential amplifier. Typical uses include bridge-based pressure and load sensing, current measurement in power-conversion systems, industrial instrumentation, and high-speed analog signal conditioning. In each case, the input common-mode range, supply voltage, output swing, gain-setting method, and required common-mode rejection must be checked against the complete manufacturer datasheet before implementation. Designers should pay particular attention to input filtering, resistor matching, supply bypassing, and the output reference connection. The INA133UA is not automatically interchangeable with every 8-pin amplifier because package compatibility alone does not guarantee electrical compatibility. Verify the exact pinout, supply ratings, common-mode limits, gain configuration, and stability requirements before releasing a PCB. This product page combines the verified Texas Instruments product description, distributor package information, price reference, and cross-reference results with practical selection guidance for engineers evaluating a drop-in replacement.
INA141P - Precision G=10/100 Low-Power Amplifier | Texas Instruments
The Texas Instruments INA141P is a precision, low-power instrumentation amplifier with selectable gains of 10 and 100, low maximum offset voltage of 50 µV, and high minimum common-mode rejection of 117 dB. It operates from dual supplies up to ±18 V and is supplied in an 8-pin plastic DIP package. The device is designed for accurate differential-signal conditioning where low offset, low drift, and high common-mode rejection are important. An instrumentation amplifier is a differential-input analog IC that amplifies the voltage difference between two signals while rejecting signals common to both inputs. The INA141 uses a versatile three-op-amp architecture, placing it in the instrumentation-amplifier hierarchy within the broader amplifier and signal-conditioning categories. Its general-purpose design is suitable for industrial measurement, sensor interfaces, current sensing, and other circuits that require differential gain and accurate signal extraction. Key features include a maximum offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, accurate gain settings of 10 and 100, and maximum input bias current of 5 nA. The input stage is protected against voltages up to ±40 V, while the wide ±18 V supply range supports higher-amplitude measurement systems. The current-feedback input circuitry maintains wide bandwidth at high gain, reaching 200 kHz at a gain of 100 V/V according to the manufacturer datasheet. The INA141P is intended for precision analog front ends rather than high-speed signal processing. At gain 10 or 100, its differential amplification behavior helps reject common-mode interference from power systems, sensors, and long wiring. The low offset voltage and low thermal drift are especially useful when the amplified differential signal is small and system accuracy is determined by input-referred error rather than by the downstream converter resolution. Typical applications include current-shunt measurement, bridge-sensor signal conditioning, differential pressure sensing, industrial instrumentation, and low-level analog measurement. In these systems, the INA141P can amplify the difference between two sensor nodes while rejecting shared supply or ground disturbances. The exact input common-mode range, output swing, bandwidth, noise, and supply-current values must be confirmed against the manufacturer datasheet for the complete operating envelope. A key design consideration is to verify that the measured differential voltage, common-mode voltage, supply rails, and required output span remain within the device limits. Input protection helps manage overload conditions, but protection networks and external resistors should still be selected for the actual system. Decoupling capacitors should be placed close to the supply pins, and the source impedances should be balanced to preserve common-mode rejection and accuracy. This page synthesizes the verified Texas Instruments product information, the manufacturer datasheet, distributor listings, and cross-reference search results. It emphasizes verified INA141P capabilities, practical instrumentation-amplifier usage, and the need to confirm unreported electrical details before final design release.
INA141PA - Precision 10/100 V/V Instrumentation Amplifier | Texas Instruments
The Texas Instruments INA141PA is a precision, low-power instrumentation amplifier with selectable gains of 10 V/V or 100 V/V, supplied in an 8-pin plastic DIP package. It is designed for measuring small differential signals while rejecting common-mode noise and offset. The device provides low offset voltage of 50 µV maximum, low input bias current of 5 nA maximum, and high common-mode rejection of 117 dB minimum. Its input stage supports input protection to ±40 V, while its wide ±18 V supply range allows operation from both single-split and dual-supply systems. An instrumentation amplifier is a specialized amplifier category that combines differential input measurement, high input impedance, accurate gain setting, and strong common-mode rejection into one device. It sits between sensors, bridge transducers, and precision converters in the signal-chain hierarchy: instrumentation amplifier -> operational amplifier -> analog signal-processing IC. The INA141PA uses a three-op-amp instrumentation-amplifier architecture with current-feedback input circuitry. According to the Texas Instruments datasheet, this configuration maintains a bandwidth of 200 kHz even at a gain of 100 V/V. Key features include accurate gain selection, low offset drift of 0.5 µV/°C maximum, low quiescent current, and operation across a -40 °C to +85 °C temperature range. The 10 V/V and 100 V/V gain choices make the device useful for bridge sensors, biomedical instrumentation, current measurement, and industrial sensor interfaces where the signal is small relative to the common-mode voltage. The INA141PA is available in an 8-pin plastic DIP package, which is useful for through-hole prototypes, laboratory equipment, and legacy industrial boards. The DIP package also provides a straightforward mechanical format for socket-based designs. Its input protection rating of ±40 V helps protect the measurement inputs when external wiring or sensors can present transients beyond the normal operating signal range. Typical applications include strain-gauge and RTD bridge amplifiers, precision current shunt measurements, ECG and other biomedical instrumentation, sensor acquisition modules, and laboratory test equipment. The main design consideration is ensuring the common-mode voltage, supply rails, gain configuration, and input protection limits remain within the device specifications. Stable reference bypassing and careful grounding are also important when measuring microvolt-level signals. This page synthesizes the verified manufacturer information, package details, technical trade-offs, and drop-in replacement considerations to support faster component selection, PCB planning, and purchasing decisions.
INA141U - Precision Low-Power Instrumentation Amplifier | Texas Instruments
The Texas Instruments INA141U is a precision, low-power instrumentation amplifier with selectable gains of 10 V/V and 100 V/V, low offset voltage, and a wide common-mode input capability in an 8-pin SOIC package. According to the manufacturer product page, the INA141 family is designed for accurate differential signal conditioning where low power and compact size are important. The device uses a three-op-amp architecture and current-feedback input circuitry, providing useful bandwidth even at higher gain. An instrumentation amplifier is a specialized analog IC that amplifies the difference between two input voltages while rejecting signals common to both inputs. It belongs to the signal-conditioning and amplifier hierarchy, where instrumentation amplifiers are used ahead of analog-to-digital converters, measurement systems, sensors, and precision control equipment. The INA141U is intended for applications requiring high input impedance, accurate gain, low offset, and good common-mode rejection. Key verified characteristics include a gain accuracy of ±0.05% at G = 10, maximum low input bias current of 5 nA, minimum common-mode rejection of 117 dB, input protection to ±40 V, and a wide ±18 V supply range. The listed low offset voltage is 50 µV maximum, with low drift specified at 0.5 µV/°C maximum. These features make the device suitable for low-level differential measurements and applications where common-mode noise or input-source imbalance could otherwise reduce measurement accuracy. The INA141U combines a three-op-amp instrumentation-amplifier topology with a compact 8-pin SOIC package. The manufacturer describes current-feedback input circuitry and a bandwidth of 200 kHz at G = 100 V/V. This architecture supports a broader operating range than a simple resistive differential amplifier, although bandwidth, output swing, supply voltage, input common-mode range, and external gain-setting requirements must still be checked against the datasheet. Typical uses include sensor-interface signal conditioning, bridge excitation and readout, industrial measurement systems, biomedical instrumentation, audio and communication front ends, and precision analog-to-digital converter inputs. The INA141 is specified for a −40°C to +85°C temperature range in the 8-pin SOIC package, making it suitable for industrial equipment where extended commercial temperature operation is required. A practical design should begin by checking differential signal range, common-mode voltage, gain selection, supply headroom, output swing, and the input network. The gain is selected through the external resistor connected to the gain-setting pin according to the manufacturer application guidance. Keep input and feedback routing short, use a stable reference and resistor network where applicable, and provide decoupling close to the supply pins. This page consolidates verified manufacturer and distributor information, practical design guidance, application context, and strict source traceability. Because the supplied data does not include a verified public pinout table, pricing tiers beyond the provided marketplace indication, or verified drop-in substitute specifications, those fields are conservatively marked for validation rather than inferred.
INA141UA - G=10/100 Instrumentation Amplifier | TI
The Texas Instruments INA141UA is a precision, low-power, three-op-amp instrumentation amplifier with selectable gains of 10 V/V or 100 V/V, 200 kHz bandwidth at a gain of 100, and an 8-pin SOIC package. It provides a maximum input offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, maximum input bias current of 5 nA, and minimum common-mode rejection of 117 dB. The input stage tolerates differential signals up to ±40 V. An instrumentation amplifier is a specialized amplifier that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. The INA141 belongs to the amplifier hierarchy as an instrumentation amplifier, differential amplifier, and analog signal-conditioning IC. Its three-op-amp architecture provides accurate gain, high common-mode rejection, and balanced input impedance, making it useful for sensors whose outputs sit on a large common-mode voltage. The INA141 uses a versatile three-op-amp design and current-feedback input circuitry. This architecture maintains 200 kHz bandwidth even at the higher gain of 100 V/V. The available gain settings are implemented through simple pin connections without external gain-setting resistors, reducing component count and avoiding the tolerance and temperature errors introduced by a conventional external resistor network. Its low 5 nA maximum input bias current is particularly useful for high-impedance sources. The device is designed for precision measurement of low-level differential signals rather than for driving heavy loads. Its maximum offset voltage of 50 µV and drift of 0.5 µV/°C help maintain accuracy as temperature changes, while 117 dB minimum common-mode rejection suppresses common-mode noise and supply-related disturbances. The listed wide supply range of ±18 V accommodates dual-supply instrumentation systems, although operating-limit details should be confirmed in the manufacturer datasheet for a specific design. Typical applications include bridge-transducer signal conditioning, strain-gauge and pressure-sensor amplification, current-shunt measurement, isolated or high-voltage sensor interfaces, laboratory instrumentation, and precision industrial control systems. Input protection to ±40 V is useful when the sensor input can exceed the normal operating range, but system-level protection, grounding, and common-mode limits still require careful review. The principal design consideration is common-mode range. A high common-mode rejection ratio does not permit the input common-mode voltage to exceed the amplifier's linear input range. Designers should also place input and reference components for low noise, avoid long sensitive traces, and preserve the specified gain connections. Decoupling capacitors should be positioned close to the supply pins according to the manufacturer's layout guidance. This page combines verified manufacturer and distributor information with application guidance, drop-in candidate comparisons, and design checks. It also distinguishes verified INA141UA parameters from data that must be confirmed in the manufacturer datasheet, helping engineers select and implement the amplifier without relying on unverified substitute specifications.
INA143U - 5V/us G=10 Differential Amplifier | Texas Instruments
The Texas Instruments INA143U is a high-speed, precision difference amplifier with a 5 V/us slew rate, 250 uV maximum offset voltage, and selectable gain of 10 V/V or 0.1 V/V, housed in an 8-pin SOIC package. It is designed to amplify the voltage difference between two inputs while rejecting common-mode signals. A difference amplifier is a specialized operational-amplifier configuration that measures IN+ relative to IN- and can reject large common-mode voltages that would overwhelm a conventional single-ended amplifier. The INA143 family integrates precision, ratio-matched resistors to implement fixed gain without external feedback components. This simplifies differential sensing in instrumentation, current measurement, and signal-conditioning circuits while reducing resistor-matching errors. Verified headline specifications include a 5 V/us high slew rate, maximum offset voltage of 250 uV, low offset drift of 3 uV/C maximum, and gain error of 0.01%. The internal gain is selectable between G=10 and G=0.1. The low-cost design targets common-mode input operation from 0.1 V, while its high-speed behavior supports accurate reproduction of rapidly changing differential waveforms. The INA143U uses matched internal resistor networks to convert the differential input into a single-ended output. The manufacturer notes that the networks are ratio matched but may vary by up to 20% in absolute resistance. That distinction matters: ratio matching supports gain accuracy, but the absolute value should not be treated as a precision external resistor value. Input bias-current and offset-current effects are included in certain published noise and DC specifications. Typical uses include high-side current sensing in an industrial bus, differential sensor interfaces, analog measurement systems, power-converter feedback, and communications circuitry. Its 8-SOIC format supports conventional surface-mount assembly, although exposed-pad thermal performance is not specified in the provided data. The device operates from dual supplies described in the manufacturer materials, but a single-supply compatibility design must be verified from the complete datasheet before implementation. When laying out this amplifier, route differential inputs as a compact, matched pair and keep them away from switching-current paths. Place its input/output decoupling capacitors close to the supply and signal pins, and verify common-mode voltage, output swing, supply polarity, and settling performance under the intended load. The INA143U is appropriate when a matched G=10 or G=0.1 network, fast slew rate, and low offset are more important than external gain programmability. This page consolidates the verified manufacturer information, distributor availability, pricing snapshot, pin details, and application guidance for engineers comparing precision difference amplifiers. It also distinguishes verified drop-in candidates from functional alternatives, preventing unsupported substitutions.